Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

A Theoretical Investigation of Vortex-Sheet Deformation Behind a Highly Loaded Wing and Its Effect on Lift

The induced drag polar is developed for wt-ngs capable of attaining extremely high loadings while possessing an elliptical distribution of circulation. This development is accomplished through a theoretical investigation of the vortex-wake deformation process and the deduction of the airfoil forces from the impulse and kinetic energy contents of the ultimate wake form. The investigation shows that the induced velocities of the wake limit the maximum lift coefficient to a value of 1.94 times the wing aspect ratio, for aspect ratios equal to or less than 6.5, and that the section properties of the airfoil limit the lift coefficient to 12.6 for aspect ratios greater than 6.5. Relations are developed for the rate of deformation of the vortex wake. It is also shown that linear wing theory is app1icable up to lift coefficients equal to 1.1 times the aspect ratio.

Cone, Clarence D., Jr.↗

Modification in drag of turbulent boundary layers resulting from manipulation of large-scale structures

The effects of placing a parallel-plate turbulence manipulator in a boundary layer are investigated by means of flow visualization and hot-wire measurements. The manipulator was found to be effective in inhibiting the intermittent large scale structure of the boundary layer, and the effect persists for at least 70 boundary-layer thicknesses downstream of the manipulator. With the removal of the large scale, there was an observed reduction in the streamwise turbulence intensity levels near the wall. The downstream distribution of the skin friction coefficient, determined from the stream wise change in fluid momentum, was also altered by the introduction of the manipulator. The data from both the visualization and hot wire studies are provided.

Corke, T. C.↗

Gross-fragmentation of meteoroids and bulk density of Geminids from photographic fireball records

The explicit solution of the drag and ablation equations of a single nonfragmenting meteoroid moving in any actual atmosphere was published several years ago. The solution yields the theoretical relation of l, the distance flown by the meteoroid in its trajectory, as a function of time, t, assuming that the height, h, is a known function of l. The photographic records of meteors and fireballs are coded by time marks, using a rotating shutter or a similar device to break the moving image. Time is, thus, the independent variable and for each time mark on a meteoroid trajector, the observed distance along the trajectory, l sub obs, as well as the double- or multiple- station photographs of the same meteoroid. Applying this solution to all available Prairie Network (PN) fireball-records, we recognized that the majority of them gave good solutions with standard deviations somewhat bigger than the intrinsic geometrical precision of the data. We also noticed that, on an average, previous methods of evaluation of the meteoroid velocities (interpolation polynomials, numerical differenciation of the observed l sub obs) used up to only several tens of percent of the intrinsic precision of the PN observational data. When residuals of these solutions, i.e. l sub obs - l sub com, were represented as a function of time for about 75 percent of solutions. The remaining 25 percent of residuals showed systematic changes with time exceeding one standard deviation. We tried to explain these systematic time course of residuals by using different meteoroids first computed theoretically and then analyzed by the same model as the natural PN fireballs were. The conclusion of these model computations is that systematic time changes of residuals in the nonfragmenting model exceeding one standard of deviation are caused by sudden gross fragmentation at one or more trajectory points. Thus, we generalized the explicit solution of the drag and ablation equations of a single nonfragmenting meteoroid by allowing for one or more points, where sudden gross fragmentation can occur. Using this generalized solution, the distances along the meteoroid trajectory can be computed for any choice of input parameters and compared with the observed distances flown by the meteoroid. For the most precise and long fireball trajectories, the least-squares solution can, thus, yield the initial velocities, the ablation coefficients, the dynamical masses, the positions of gross-fragmentation points, and the terminal mass. At a gross-fragmentation point, the ratio of the main mass to all the remaining fragments can be compared with the dynamic mass determined from our gross-fragmentation model and, thus, the meteoroid bulk density can be evaluated. We applied the gross-fragmentation model to sever PN fireballs showing time changes of residuals, and we recognized that, in all these cases, the new computed bulk densities of meteoroids resulted higher in comparison with the meteoroid densities determined with the non-gross-fragmentation model. Other aspects of the study are discussed.

Ceplecha, Zdenek↗

Preliminary Results of a Free-Flight Investigation of the Static Stability and Aileron Control Characteristics of 1/6 Scale Models of the Bell MX-776

An investigation of the static longitudinal stability, static directional stability, and aileron control characteristics at transonic and supersonic speeds is being made of 1/6 scale rocket-propelled model of the Bell MX-776. A stability investigation has been made of two symmetrical models with controls undeflected and centers of gravity one-half and one-body diameter, respectively, ahead of the equivalent design center-of-gravity location of the full-scale version. Both models developed large normal-force coefficients in both the subsonic and supersonic ranges which indicated longitudinal instability at low angles of attack. The side-force coefficients were small for both models and indicated that the models were directionally stable. A possible tendency toward dynamic directional instability in the transonic region was indicated by short-period oscillations of the side forces. The results showed a partial-span inboard aileron to be ineffective or to cause negative control in the the transonic region when deflected approximately 5 deg but not when deflected 10 deg. An investigation of drag showed it to increase with a rearward movement of the center of gravity. This indicates an increase in the trim angle of attack as could be caused by a decrease in static stability.

Michal, David H.↗

Lecture Series "Boundary Layer Theory". Part I - Laminar Flows: Laminar Flows - Part 1

In the lecture series starting today author want to give a survey of a field of aerodynamics which has for a number of years been attracting an ever growing interest. The subject is the theory of flows with friction, and, within that field, particularly the theory of friction layers, or boundary layers. A great many considerations of aerodynamics are based on the ideal fluid, that is the frictionless incompressibility and fluid. By neglect of compressibility and friction the extensive mathematical theory of the ideal fluid, (potential theory) has been made possible. Actual liquids and gases satisfy the condition of incomressibility rather well if the velocities are not extremely high or, more accurately, if they are small in comparison with sonic velocity. For air, for instance, the change in volume due to compressibility amounts to about 1 percent for a velocity of 60 meters per second. The hypothesis of absence of friction is not satisfied by any actual fluid; however, it is true that most technically important fluids, for instance air and water, have a very small friction coefficient and therefore behave in many cases almost like the ideal frictionless fluid. Many flow phenomena, in particular most cases of lift, can be treated satisfactorily, - that is, the calculations are in good agreement with the test results, -under the assumption of frictionless fluid. However, the calculations with frictionless flow show a very serious deficiency; namely, the fact, known as d'Alembert's paradox, that in frictionless flow each body has zero drag whereas in actual flow each body experiences a drag of greater or smaller magnitude. For a long time the theory has been unable to bridge this gap between the theory of frictionless flow and the experimental findings about actual flow. The cause of this fundamental discrepancy is the viscosity which is neglected in the theory of ideal fluid; however, in spite of its extraordinary smallness it is decisive for the course of the flow phenomena.

Schlichting, H.↗

OC6 phase I: Improvements to the OpenFAST predictions of nonlinear, low-frequency responses of a floating offshore wind turbine platform

We report in the OC5 and OC6 projects, the authors observed a persistent underprediction of the nonlinear, low-frequency responses of an offshore wind semisubmersible with many mid-fidelity engineering models, including the OpenFAST tool developed by the National Renewable Energy Laboratory. Both the low-frequency wave excitation in surge and pitch and the resulting resonance motions were severely underpredicted. In response, we developed several modifications to the OpenFAST model from the OC5/6 projects to improve the predictions of the low-frequency wave loads and responses. All modifications are in the modeling of the viscous drag forces. Efforts were made to provide physical justifications to the changes and to limit the number of additional parameters requiring tuning, so that the modified model can be applied to other floating wind systems. With the proposed modifications, the predictions of the low-frequency surge and pitch wave loads on a fixed floater and the resonance responses of a floating structure are both significantly improved with a single set of model coefficients, which leads to good agreement with the measurements from the OC6 wave-basin experimental campaign.

17 WIND ENERGY↗

Ground simulation and tunnel blockage for a jet-flapped, basic STOL model tested to very high lift coefficients

Ground effects experiments and large/small-tunnel interference studies were carried out on a model with a 20-inch (50.8 cm) span wing. The wing, which includes a highly deflected knee-blown flap can be fitted with unflapped tips and slats. A low-mounted tailplane can be fitted to the aft fuselage. Three-component balance meaurements, made with a fixed ground equipped with a single boundary-layer blowing slot, were compared with datum, moving-ground results. Good comparisons were obtained up to model blowing momentum coefficients of approximately two, after which the particular floor blowing settings used proved insufficient to prevent floor separation in the vicinity of the model. Skin friction measurements, taken routinely along the floor centerline, proved invaluable during the analysis of results, and their use is recommended as input to determination of floor BLC setting. A careful investigation was made of pitching moments, including tail-on, close-to-ground cases, with favorable results. Drag proved the most sensitive to the change from a moving to the boundary-layer controlled ground.

Hackett, J. E.↗

F-8 supercritical wing flight pressure, Boundary layer, and wake measurements and comparisons with wind tunnel data

Data for speeds from Mach 0.50 to Mach 0.99 are presented for configurations with and without fuselage area-rule additions, with and without leading-edge vortex generators, and with and without boundary-layer trips on the wing. The wing pressure coefficients are tabulated. Comparisons between the airplane and model data show that higher second velocity peaks occurred on the airplane wing than on the model wing. The differences were attributed to wind tunnel wall interference effects that caused too much rear camber to be designed into the wing. Optimum flow conditions on the outboard wing section occurred at Mach 0.98 at an angle of attack near 4 deg. The measured differences in section drag with and without boundary-layer trips on the wing suggested that a region of laminar flow existed on the outboard wing without trips.

Montoya, L. C.↗

Effects of Wing Flaps and Wing Duct Inlet on the Lift and Stalling Characteristics of a 1/4-Scale Partial-Span Model of the Republic XF-12 Airplane in the Langley 19-Foot Pressure Tunnel

An investigation was conducted in the Langley 19-foot pressure tunnel to determine the lift, drag, pitching-moment and stalling characteristics fo a 1/4 -scale partial-span model of the left wing of the Republic XF-12 airplane. The effects of a duct inlet, located between the nacelles at the leading edge of the wing, on those characteristics were also investigated. The Reynolds numbers for the investigation covered a range from 4,500,000 to 8,600,000. The results of the investigation indicated that maximum lift coefficients of 1.36, 1.71, and 2.11 were measured on the model with flaps neutral and deflected 20 deg and 55 deg, respectively at a Reynolds number of 8,600,000. When the duct inlet was replaced by a basic airfoil nose the flap-neutral maximum-lift coefficient was increased from 1.36 to 1.41. The results also showed that at maximum lift with flaps neutral or deflected 55 deg. most of the area between the nacelles were stalled while only small areas on other portions of the model were stalled; when the duct inlet was replaced by the basic airfoil nose the stall was delayed to a slightly higher angle of attack but the nature of the stall was relatively unaffected.

Graham, Robert R.↗

Jupiter - Structure and composition of the upper atmosphere

The Voyager ultraviolet stellar occultation data yield a temperature of 200 + or - 50 K at about 400 km, and the solar occultation data give 1100 + or - 200 K at 1450 km above the ammonia cloud tops. The temperature gradient between 400 and 1450 km is approximately 1 K/km. The mesospheric temperature structure gives no strong indication of an earth-like mesopause. The heating of the upper atmosphere appears to result from a combination of magnetospheric charged particle precipitation, ion drag, inertia gravity waves, and solar EUV. The volume mixing ratios of CH4 and C2H6 at 325 km are measured to be 2.5(+3, -2) x 10 to the -5th and 2.5(+2.0, -1.5) x 10 to the -6th, respectively, which are lower than in the stratosphere. The C2H2 volume mixing ratio is not greater than 5 x 10 to the -6th at 300 km. The homopause value of the equatorial eddy diffusion coefficient is found to be 1-2 x 10 to the -6th sq cm/s.

Atreya, S. K.↗

Miniature drag force anemometer

A miniature drag force anemometer is described which is capable of measuring dynamic velocity head and flow direction. The anemometer consists of a silicon cantilevered beam 2.5 mm long, 1.5 mm wide, and 0.25 mm thick with an integrated diffused strain gage bridge, located at the base of the beam, as the force measuring element. The dynamics of the beam are like that of a second order system with a natural frequency of about 42 kHz and a damping coefficient of 0.007. The anemometer can be used in both forward and reversed flow. Measured flow characteristics up to Mach 0.6 are presented along with application examples including turbulence measurements.

Krause, L. N.↗

Comparison of theoretical and experimental thrust performance of a 1030:1 area ratio rocket nozzle at a chamber pressure of 2413 kN/m2 (350 psia)

The joint Army. Navy, NASA. Air Force (JANNAF) rocket engine peformnace prediction procedure is based on the use of various reference computer programs. One of the reference programs for nozzle analysis is the Two-Dimensional Kinetics (TDK) Program. The purpose of this report is to calibrate the JANNAF procedure incorporated into the December l984 version of the TDK program for the high-area-ratio rocket engine regime. The calibration was accomplished by modeling the performance of a 1030:1 rocket nozzle tested at NASA Lewis Research Center. A detailed description of the experimental test conditions and TDK input parameters is given. The results show that the computer code predicts delivered vacuum specific impulse to within 0.12 to 1.9 percent of the experimental data. Vacuum thrust coefficient predictions were within + or - 1.3 percent of experimental results. Predictions of wall static pressure were within approximately + or - 5 percent of the measured values. An experimental value for inviscid thrust was obtained for the nozzle extension between area ratios of 427.5 and 1030 by using an integration of the measured wall static pressures. Subtracting the measured thrust gain produced by the nozzle between area ratios of 427.5 and 1030 from the inviscid thrust gain yielded experimental drag decrements of 10.85 and 27.00 N (2.44 and 6.07 lb) for mixture ratios of 3.04 and 4.29, respectively. These values correspond to 0.45 and 1.11 percent of the total vacuum thrust. At a mixture ratio of 4.29, the TDK predicted drag decrement was 16.59 N (3.73 lb), or 0.71 percent of the predicted total vacuum thrust.

Smith, Tamara A.↗

Miniature drag-force anemometer

A miniature drag-force anemometer is described which is capable of measuring dynamic velocity head and flow direction. The anemometer consists of a silicon cantilever beam 2.5 mm long, 1.5 mm wide, and 0.25 mm thick with an integrated diffused strain-gage bridge, located at the base of the beam, as the force measuring element. The dynamics of the beam are like those of a second-order system with a natural frequency of about 42 kHz and a damping coefficient of 0.007. The anemometer can be used in both forward and reversed flow. Measured flow characteristics up to Mach 0.6 are presented along with application examples including turbulence measurements.

Krause, L. N.↗

Aerodynamic characteristics induced on a supercritical wing due to vectoring twin nozzles at Mach numbers from 0.40 to 0.95

The induced lift characteristics are studied for a vectored-thrust concept in which jet-exhaust nozzles were located in the fuselage at the wing trailing edge. The wing had a supercritical airfoil section. The investigation was conducted at Mach numbers from 0.4 to 0.95, angles of attack up to 14 deg, and thrust coefficients up to 0.35, and nozzle deflection angles of 0 deg and 30 deg. Separate force balances were used to determine both total aerodynamic and thrust forces alone which allowed for a direct measurement of jet turning angle at forward speeds. The Reynolds number per meter varied from 8.20 x 1 million to 12.80 x 1 million. The results show that the configuration with the supercritical wing generally had a better performance with respect to both lift augmentation and drag reduction than the same configuration with a 64 series airfoil.

Capone, F. J.↗

Earth return aerocapture for manned Mars missions

Lift to drag ratio (L/D) requirements and stagnation point heating have been examined for a variety of probable entry conditions and vehicle configurations. It is found that vehicles with an L/D of 0.5 or more provide a corridor width of at least 0.7 degrees while keeping the peak deceleration load below 5 g for approach velocities up to 14.5 km/s. It is shown that stagnation point peak heating rates and integrated heat load critically depend on both entry velocity and ballistic coefficient. For the most severe cases under consideration, peak heating and integrated heat load are five times greater than those encountered by Apollo but within the range of experience for unmanned vehicles.

Tauber, M. E.↗

Comparisons of two-dimensional shock-expansion theory with experimental aerodynamic data for delta-planform wings at high supersonic speeds

An investigation has been conducted to explore the potential for optimizing airfoil shape at high supersonic speeds by utilizing the two-dimensional shock-expansion method. Theoretical and experimental force and moment coefficients are compared for four delta-planform semispan wings having a leading-edge sweep angle of 65 deg and incorporating modified diamond airfoils with a thickness-chord ratio of 0.06. The wings differ only in airfoil maximum-thickness position and camber. The experimental data are obtained at Mach numbers of 3.95 and 4.63 and at a Reynolds number of 9.84 million per meter. A relatively simple method is developed for predicting, in terms of lift-drag ratio, the optimum modified diamond airfoil at high supersonic and hypersonic speeds.

Jernell, L. S.↗

Analyses of the solid earth and ocean tidal perturbations on the orbits of the GEOS-1 and GEOS-2 satellites

The luni-solar tidal perturbations in the inclination of the GEOS-I and GEOS-II satellite orbits were analyzed for the solid Earth and ocean tide conditions. Precision reduced camera and TRANET Doppler observations spanning periods of over 600 days for each satellite were used to derive mean orbital elements. Perturbations due to the earth's gravity field, solar radiation pressure, and atmospheric drag were modelled, and the resulting inclination residuals were analyzed for tidal effects. The amplitudes of the observed total tidal effects were about 1.2 arc seconds (36 meters) in the inclination of GEOS-I and 4.5 arc seconds (135 meters) for GEOS-II. The solid earth tides were then modelled using earth tide measurements, earth rotation observations, and seismic data. The resulting inclination residuals were analyzed for ocean tide parameters. The derived parameters consist of one second degree coefficient and an accompanying phase angle in a spherical harmonic expansion of the ocean tidal potential for each tidal constituent. The results are presented.

Felsentreger, T. L.↗

Free-Flight Tests of Fifth-Stage Scout Entry Vehicle at Mach Numbers of 5 and 17

Measurements have been made in air at two Mach numbers of the static stability, normal force, and drag of a version of the fifth-stage Scout entry vehicle. The most significant result was that the design center of gravity led to a condition of static instability at small angles of attack at Mach number 17. At this Mach number, the static stability was a highly nonlinear function of the angle of attack. A useful method for analyzing free-flight data having this nonlinear behavior is included in this report. Comparisons were made between the measured aerodynamic coefficients and those estimated by Newtonian impact theory and by a method developed by Seiff and Whiting. The latter method gave good estimates of the normal-force-curve slope at both Mach numbers and of the moment-curve slope at the lower Mach number. It resulted in an overestimation of the static stability at Mach number 17, although it gave results decidedly closer to the experimental value than did Newtonian impact theory.

FREE FLIGHT↗