SEARCH · Engineering Papers

Results for “Commanding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Selectable towline spin chute system

An emergency spin recovery parachute is presented that is housed within a centrally mounted housing on the aft end of an aircraft and connected to a ring fitting within the housing. Two selectively latching shackles connected to separate towlines are openly disposed adjacent the ring fitting. The towlines extend in opposite directions from the housing along the aircraft wing to attachment points adjacent the wing-tips where the other end of each towline is secured. Upon pilot command, one of the open shackles latches to the ring fitting to attach the towline connected thereto, and a second command signal deploys the parachute. Suitable break-away straps secure the towlines to the aircraft surface until the parachute is deployed and the resulting force on the towline attached to the parachute overcomes the straps and permits the towline to extend to the point of attachment to exert sufficient drag on the spinning aircraft to permit the pilot to regain control of the aircraft. To employ the parachute as a drag chute to reduce landing speeds, both shackles and their respective towlines are latched to the ring fitting.

Vairo, Daniel M.↗

NASA NTRS1990

EMG analysis of human postural responses during parabolic flight microgravity episodes

Anticipatory postural activity in the trunk and legs precedes rapid shoulder flexion in unit gravity. The hypothesis that anticipatory activity is a component of a single neural command for arm movement was tested by monitoring the surface electromyographic activity of the biceps femoris, paraspinals, and deltoid muscles of three subjects during the microgravity phase of parabolic flight. If part of a single command, anticipatory postural activity would be expected to remain intact despite the absence of the body's center of gravity in a reduced gravity environment. However, in at least 75 percent of the microgravity trials anticipatory biceps femoris activity was absent, indicating a separation of postural and agonist muscle activity. Such a finding suggests that anticipatory postural biceps femoris activity may be initiated independently of agonist (deltoid) activity.

Layne, Charles S.↗

NASA NTRS1990

UMI - An interactive supervisory and shared control system for telerobotics

An interactive user interface, User-Macro-Interface (UMI), and its complete task execution system are developed and implemented for utilization by an operator to describe, simulate and execute tasks on a multiarm telerobot. The sequences or primitives can be executed on a graphics simulator or on the JPL Telerobot which incorporates two task execution manipulators, one manipulation used for positioning cameras, and two 6-degree-of-freedom force-reflecting hand controllers employed for shared and teleoperation modes of execution. The UMI interface is to be used as the operator interface at a local command site to prepare and send commands to a remote space telerobot.

Backes, Paul G.↗

NASA NTRS1991

Effect of motor dynamics on nonlinear feedback robot arm control

A nonlinear feedback robot controller that incorporates the robot manipulator dynamics and the robot joint motor dynamics is proposed. The manipulator dynamics and the motor dynamics are coupled to obtain a third-order-dynamic model, and differential geometric control theory is applied to produce a linearized and decoupled robot controller. The derived robot controller operates in the robot task space, thus eliminating the need for decomposition of motion commands into robot joint space commands. Computer simulations are performed to verify the feasibility of the proposed robot controller. The controller is further experimentally evaluated on the PUMA 560 robot arm. The experiments show that the proposed controller produces good trajectory tracking performances and is robust in the presence of model inaccuracies. Compared with a nonlinear feedback robot controller based on the manipulator dynamics only, the proposed robot controller yields conspicuously improved performance.

Tarn, Tzyh-Jong↗

NASA NTRS1990

Control of multiple resonant power processors in a multi-source system

Analysis and test results show that phasor-regulated, Mapham-derived resonant inverters can be paralleled to provide standardizing interfaces for multiple sources on a utility-type, aerospace power distribution bus. The basic sources do not require matching in any way, and may have grossly different characteristics. Fully stable system architectures with multiple sources, parallel/redundant distribution buses, and a wide variety of loads can be easily constructed and controlled. The commands and parameters available for system control allow for tight tolerance bus voltage control, and absolute power-sharing control from the various sources over the full range of possible source and load variations. That level of control enables simplified load power processing hardware and the distribution of losses to optimally load the source thermal control system. Positive control of all system performance and allocation of losses are not required by all missions or vehicles, and overall vehicle considerations do not always require the loads on vehicle energy sources and thermal control systems to be balanced. In those cases, power system control can be simplified, and a hierarchical set of defaults can be substituted for computer-generated or supervisory input commands to allow for stable, fully autonomous system operation.

Mildice, James↗

NASA NTRS1990

Primary lithium cell life studies

One solution for providing a truly independent power source is to package, within the critical subsystem element, a primary battery that can remain dormant for time periods as long as the mission life, which can be 10-15 years, maximum. When primary power from the spacecraft solar array/battery system is interrupted, the backup battery system, which is connected through a diode to the power input line, would automatically support the load to avoid a power interruption to the critical load for a time period long enough to ensure that ground control could access the satellite and correct the anomaly by sending appropriate commands to the spacecraft. Critical subsystems identified for the application are telemetry and command circuits, volatile computer memory, attitude control circuits, and some critical payloads. Due to volume packaging and weight restrictions that exist on most spacecraft, coupled with the long storage periods required, lithium cell technology was selected for the backup power source. Because of the high energy density (200-400 Wh/kg), long shelf life, and load capability, soluble cathode primary lithium technology was chosen. The most important lithium cell properties that require detail characterization for this application are capacity loss, shelf life, and the voltage delay mechanism. These are functions of storage time and temperature. During storage, a passive film builds up on the lithium electrode. The film protects the lithium electrode from progressive capacity decay but requires time to break down when a load is applied. This phenomenon results in a depressed voltage during the period of film breakdown which can last from fractions of a second to minutes.

Capulli, John↗

NASA NTRS1991

Ulysses spacecraft control and monitoring system

The baseline Ulysses spacecraft control and monitoring system (SCMS) concepts and the converted SCMS, residing on a DEC/VAX 8350 hardware, are considered. The main functions of the system include monitoring and displaying spacecraft telemetry, preparing spacecraft commands, producing hard copies of experimental data, and archiving spacecraft telemetry. The SCMS system comprises over 20 subsystems ranging from low-level utility routines to the major monitoring and control software. These in total consist of approximately 55,000 lines of FORTRAN source code and 100 VMS command files. The SCMS major software facilities are described, including database files, telemetry processing, telecommanding, archiving of data, and display of telemetry.

Hamer, P. A.↗

NASA NTRS1991

Helicopter flight-control design using an H(2) method

Rate-command and attitude-command flight-control designs for a UH-60 helicopter in hover are presented and were synthesized using an H(2) method. Using weight functions, this method allows the direct shaping of the singular values of the sensitivity, complementary sensitivity, and control input transfer-function matrices to give acceptable feedback properties. The designs were implemented on the Vertical Motion Simulator, and four low-speed hover tasks were used to evaluate the control system characteristics. The pilot comments from the accel-decel, bob-up, hovering turn, and side-step tasks indicated good decoupling and quick response characteristics. However, an underlying roll PIO tendency was found to exist away from the hover condition, which was caused by a flap regressing mode with insufficient damping.

Takahashi, Marc D.↗

NASA NTRS1990

BIRD: A general interface for sparse distributed memory simulators

Kanerva's sparse distributed memory (SDM) has now been implemented for at least six different computers, including SUN3 workstations, the Apple Macintosh, and the Connection Machine. A common interface for input of commands would both aid testing of programs on a broad range of computer architectures and assist users in transferring results from research environments to applications. A common interface also allows secondary programs to generate command sequences for a sparse distributed memory, which may then be executed on the appropriate hardware. The BIRD program is an attempt to create such an interface. Simplifying access to different simulators should assist developers in finding appropriate uses for SDM.

Rogers, David↗

NASA NTRS1991

Linear quadratic servo control of a reusable rocket engine

A design method for a servo compensator is developed in the frequency domain using singular values. The method is applied to a reusable rocket engine. An intelligent control system for reusable rocket engines was proposed which includes a diagnostic system, a control system, and an intelligent coordinator which determines engine control strategies based on the identified failure modes. The method provides a means of generating various linear multivariable controllers capable of meeting performance and robustness specifications and accommodating failure modes identified by the diagnostic system. Command following with set point control is necessary for engine operation. A Kalman filter reconstructs the state while loop transfer recovery recovers the required degree of robustness while maintaining satisfactory rejection of sensor noise from the command error. The approach is applied to the design of a controller for a rocket engine satisfying performance constraints in the frequency domain. Simulation results demonstrate the performance of the linear design on a nonlinear engine model over all power levels during mainstage operation.

Musgrave, Jeffrey L.↗

NASA NTRS1991

Hipparcos

The primary objective of Hipparcos is to provide very accurate star map data and star position accuracies on the order of 2 arc seconds. Hipparcos was planned to be in a geostationary orbit, but due to failure of the apogee motor, it is currently in a high elliptical orbit and has a 10.8 hour period. Goldstone 26 m will provide 6-8 hours per day support for real-time telemetry and command. Mission-dependent equipment is required at Goldstone, and telemetry and command data will be transmitted from Goldstone to European Space Operations Control Center (ESOC) via satellite links. Operations support is scheduled to begin 12 Mar. 1990.

Source record↗

NASA NTRS1991

Nimbus-7

The DSN (Deep Space Network) mission support requirements for Nimbus 7 are summarized. The basic Nimbus series spacecraft is attitude-stabilized in three axes, with the yaw axis always pointing towards the center of the Earth. The spacecraft provides a stable platform, power, command, and data handling support for active and passive sensors for daily global surveillance of the atmosphere, and for mapping details of the atmospheric structure and Earth surface from satellite altitudes. The Nimbus 7 mission objectives are outlined and the DSN support requirements are defined through the presentation of tables and narratives describing the spacecraft flight profile; DSN support coverage; S-band frequency assignments; support parameters for telemetry, command and support systems; and tracking support responsibility.

Foreman, M.↗

NASA NTRS1991

Development and application of virtual reality for man/systems integration

While the graphical presentation of computer models signified a quantum leap over presentations limited to text and numbers, it still has the problem of presenting an interface barrier between the human user and the computer model. The user must learn a command language in order to orient themselves in the model. For example, to move left from the current viewpoint of the model, they might be required to type 'LEFT' at a keyboard. This command is fairly intuitive, but if the viewpoint moves far enough that there are no visual cues overlapping with the first view, the user does not know if the viewpoint has moved inches, feet, or miles to the left, or perhaps remained in the same position, but rotated to the left. Until the user becomes quite familiar with the interface language of the computer model presentation, they will be proned to lossing their bearings frequently. Even a highly skilled user will occasionally get lost in the model. A new approach to presenting type type of information is to directly interpret the user's body motions as the input language for determining what view to present. When the user's head turns 45 degrees to the left, the viewpoint should be rotated 45 degrees to the left. Since the head moves through several intermediate angles between the original view and the final one, several intermediate views should be presented, providing the user with a sense of continuity between the original view and the final one. Since the primary way a human physically interacts with their environment should monitor the movements of the user's hands and alter objects in the virtual model in a way consistent with the way an actual object would move when manipulated using the same hand movements. Since this approach to the man-computer interface closely models the same type of interface that humans have with the physical world, this type of interface is often called virtual reality, and the model is referred to as a virtual world. The task of this summer fellowship was to set up a virtual reality system at MSFC and begin applying it to some of the questions which concern scientists and engineers involved in space flight. A brief discussion of this work is presented.

Brown, Marcus↗

NASA NTRS1991

NASA Goddard Space Flight Center Robotic Processing System Program Automation Systems, volume 2

Topics related to robot operated materials processing in space (RoMPS) are presented in view graph form. Some of the areas covered include: (1) mission requirements; (2) automation management system; (3) Space Transportation System (STS) Hitchhicker Payload; (4) Spacecraft Command Language (SCL) scripts; (5) SCL software components; (6) RoMPS EasyLab Command & Variable summary for rack stations and annealer module; (7) support electronics assembly; (8) SCL uplink packet definition; (9) SC-4 EasyLab System Memory Map; (10) Servo Axis Control Logic Suppliers; and (11) annealing oven control subsystem.

Dobbs, M. E.↗

NASA NTRS1992

An improved lateral control wheel steering law for the Transport Systems Research Vehicle (TSRV)

A lateral control wheel steering law with improved performance was developed for the Transport Systems Research Vehicle (TSRV) simulation and used in the Microwave Landing System research project. The control law converted rotational hand controller inputs into roll rate commands, manipulated ailerons, spoilers, and the rudder to achieve the desired roll rates. The system included automatic turn coordination, track angle hold, and autopilot/autoland modes. The resulting control law produced faster roll rates (15 degrees/sec), quicker response to command reversals, and safer bank angle limits, while using a more concise program code.

Ragsdale, W. A.↗

NASA NTRS1992

An intelligent control and virtual display system for evolutionary space station workstation design

Research and development of the Advanced Display and Computer Augmented Control System (ADCACS) for the space station Body-Ported Cupola Virtual Workstation (BP/VCWS) were pursued. The potential applications were explored of body ported virtual display and intelligent control technology for the human-system interfacing applications is space station environment. The new system is designed to enable crew members to control and monitor a variety of space operations with greater flexibility and efficiency than existing fixed consoles. The technologies being studied include helmet mounted virtual displays, voice and special command input devices, and microprocessor based intelligent controllers. Several research topics, such as human factors, decision support expert systems, and wide field of view, color displays are being addressed. The study showed the significant advantages of this uniquely integrated display and control system, and its feasibility for human-system interfacing applications in the space station command and control environment.

Feng, Xin↗

NASA NTRS1992

IGGy: An interactive environment for surface grid generation

A graphically interactive derivative of the EAGLE boundary code is presented. This code allows the user to interactively build and execute commands and immediately see the results. Strong ties with a batch oriented script language are maintained. A generalized treatment of grid definition parameters allows a more generic definition of the grid generation process and allows the generation of command scripts which can be applied to topologically similar configurations. The use of the graphical user interface is outlined and example applications are presented.

Prewitt, Nathan C.↗

NASA NTRS1992

Origin of orbital debris impacts on Long Duration Exposure Facility's (LDEF) trailing surfaces

Orbital debris tracked by the US Space Command is mostly in near circular orbit around the Earth. If small debris were in the same types of orbits, there would be very few orbital debris impacts on the Long Duration Exposure Facility's (LDEF's) trailing surfaces. However, at least 15 percent of the impacts found on the trailing A03 gold surface was found to be orbital debris impacts. This measurement suggests that the orbital distribution of small debris is not the same as that of larger debris. Although this is not a total surprise, since modelling of satellite breakups has predicted different distributions, it does raise questions as to what types of orbits could be responsible for these impacts. A model was developed to explain these LDEF results. The model calculates the expected debris impact crater distribution around LDEF, as a function of debris orbital parameters. The results show that only low inclination and highly elliptical orbits could be responsible for these impacts. The most common object left in this type of orbit is an orbital transfer stage, used by the US and ESA to place objects into geosynchronous orbit, and inclinations near 28 and 7 degrees for the US and ESA, respectively. Even large fragments from satellites, which break up in these types of orbits, are difficult to observe from the ground; consequently, little is known about the number and characteristics of breakups in these orbits. The LDEF data suggest that these objects are breaking up. The LDEF data also suggest that the ratio of the contribution of small debris from this type of orbit to the contribution from circular orbits is about an order of magnitude larger than the same ratio for debris tracked by the US Space Command.

Kessler, Donald J.↗