Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Automated Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Intelligent Systems Approach for Automated Identification of Individual Control Behavior of a Human Operator

Results have been obtained using conventional techniques to model the generic human operator?s control behavior, however little research has been done to identify an individual based on control behavior. The hypothesis investigated is that different operators exhibit different control behavior when performing a given control task. Two enhancements to existing human operator models, which allow personalization of the modeled control behavior, are presented. One enhancement accounts for the testing control signals, which are introduced by an operator for more accurate control of the system and/or to adjust the control strategy. This uses the Artificial Neural Network which can be fine-tuned to model the testing control. Another enhancement takes the form of an equiripple filter which conditions the control system power spectrum. A novel automated parameter identification technique was developed to facilitate the identification process of the parameters of the selected models. This utilizes a Genetic Algorithm based optimization engine called the Bit-Climbing Algorithm. Enhancements were validated using experimental data obtained from three different sources: the Manual Control Laboratory software experiments, Unmanned Aerial Vehicle simulation, and NASA Langley Research Center Visual Motion Simulator studies. This manuscript also addresses applying human operator models to evaluate the effectiveness of motion feedback when simulating actual pilot control behavior in a flight simulator.

Zaychik, Kirill B.↗
DOE OSTI2013

Automated x-ray/light field congruence using the LINAC EPID panel

Purpose: X-ray/light field alignment is a test described in many guidelines for the routine quality control of clinical linear accelerators (LINAC). Currently, the gold standard method for measuring alignment is through utilization of radiographic film. However, many modern LINACs are equipped with an electronic portal imaging device (EPID) that may be used to perform this test and thus subsequently reducing overall cost, processing, and analysis time, removing operator dependency and the requirement to sustain the departmental film processor. Methods: This work describes a novel method of utilizing the EPID together with a custom inhouse designed jig and automatic image processing software allowing measurement of the light field size, x-ray field size, and congruence between them. The authors present results of testing the method for aS1000 and aS500 Varian EPID detectors for six LINACs at a range of energies (6, 10, and 15 MV) in comparison with the results obtained from the use of radiographic film. Results: Reproducibility of the software in fully automatic operation under a range of operating conditions for a single image showed a congruence of 0.01 cm with a coefficient of variation of 0. Slight variation in congruence repeatability was noted through semiautomatic processing by four independent operators due to manual marking of positions on the jig. Testing of the methodology using the automatic method shows a high precision of 0.02 mm compared to a maximum of 0.06 mm determined by film processing. Intraindividual examination of operator measurements of congruence was shown to vary as much as 0.75 mm. Similar congruence measurements of 0.02 mm were also determined for a lower resolution EPID (aS500 model), after rescaling of the image to the aS1000 image size. Conclusions: The designed methodology was proven to be time efficient, cost effective, and at least as accurate as using the gold standard radiographic film. Additionally, congruence testing can be easily performed for all four cardinal gantry angles which can be difficult when using radiographic film. Therefore, the authors propose it can be used as an alternative to the radiographic film method allowing decommissioning of the film processor.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1978

The Array Automated Assembly Task for the Low Cost Solar Array Project, Phase 2

During the program a process sequence was proposed and tested for the fabrication of dendritic welb silicon into solar modules. This sequence was analyzed as to yield and cost and these data suggest that the price goals of 1986 are attainable. Specifically, it was shown that a low cost POCL3 is a suitable replacement for the semiconductor grade, and that a suitable CVD oxide can be deposited from a silane/air mixture using a Silox reactor. A dip coating method was developed for depositing an antireflection coating from a metalorganic precursor. Application of photoresist to define contact grids was made cost effective through use of a dip coating technique. Electroplating of both Ag and Cu was shown feasible and cost effective for producing the conductive metal grids on the solar cells. Laser scribing was used to separate the cells from the dendrites without degradation. Ultrasonic welding methods were shown to be feasible for interconnecting the cells. A study of suitable low cost materials for encapsulation suggest that soda lime glass and phenolic filled board are preferred.

Campbell, R. B.↗
NASA NTRS1984

Automated Mercury Dilatometer

Task of reading and recording indications of mercury dilatometer simplified by automatic system. Volume change of sample under test converted into electrical signal. Device modified by addition of resistance wire to mercury column. Height of column read indirectly by measuring resistance between terminals. Signal suitable for strip-chart recording or other processing.

Hong, S. D.↗
NASA NTRS1982

LANDSAT Digital Data Base Preparation for the Pennsylvania Defoliation Application Pilot Test

A LANDSAT digital mosaic data base for the State of Pennsylvania was prepared for use in the development of an automated system to annually estimate the extent and severity of Gypsy Moth defoliation of hardward forests. The techniques for detecting the defoliation and development of a geographic information system (GIS) to assess damage is being developed jointly by NASA/Goddard Space Flight Center and Pennsylvania State University using the JPL prepared mosaic base. The JPL processing involved the use of ground control points from the Master Data Processor for planimetric control, resampling of the LANDSAT data to 57 x 57 meter pixels, realignment to north, and reprojection to the Universal Transverse Mercator (UTM) projection in UTM zones 17 and 18. The completed mosaic for each UTM zone was subdivided into 1 degree of latitude by 2 degrees of longitude quadrangles for easy data handling. Consideration is given to the issues of mapping standards, sensor and spacecraft platform characteristics, and their implication to geographic information systems operation. Methods for obtaining measures of accuracy for LANDSAT mosaics are reviewed.

Mcleod, R. G.↗
NASA NTRS1992

Automated rendezvous and capture development infrastructure

The facilities at Marshall Space Flight Center and JSC to be utilized to develop and test an autonomous rendezvous and capture (ARC) system are described. This includes equipment and personnel facility capabilities to devise, develop, qualify, and integrate ARC elements and subsystems into flight programs. Attention is given to the use of a LEO test facility, the current concept and unique system elements of the ARC, and the options available to develop ARC technology.

Bryan, Thomas C.↗
NASA NTRS1995

Traffic Management Advisor: Iterative Field Development and Assessment at Multiple Sites

Previous studies have demonstrated the necessity of involving users in the development of automation aids, especially for complex domains such as air traffic control (ATC). Traditional development only demanded a single field test to validate a completed system, but a more iterative combination of development and assessment ensures that the technology meets the requirements of its application domain. Exposure across an adequate spectrum of field users is also required during development, and the use of multiple development sites provides an opportunity to consider individual facility cultures as they relate to implementation strategies. The development of the Center/TRACON Automation System (CTAS) Traffic Management Advisor (TMA) at the Denver and Dallas ATC facilities demonstrates successful iterative development and assessment at multiple field sites. The use of field development changes the nature of assessment. As development progresses, periodic assessments are required to validate that system development is progressing along an appropriate track. In the development of the TMA, assessments were performed based on software in the field, and input from traffic managers was analyzed and incorporated into subsequent releases of the TMA, to be reassessed in the field. This has led to a tool with operational suitability and broad user acceptance. Assessment at multiple sites provides a more generalizable perspective that allows the production of a system that is both generic enough to be used at different sites and tailored enough to be of use at any site. In addition to providing a better understanding of specific facility requirements, the use of multiple assessment sites in the development of TMA has provided an opportunity to consider individual facility operations, procedures and cultures as they relate to development and implementation strategies.

Sanford, Beverly D.↗
NASA NTRSDate not supplied

Uniform Dust Deposition System for Dust Tolerance Studies

Future missions to the Moon will require mechanisms and materials to effectively and reliably operate in the presences of lunar regolith. One of the challenges of developing such technologies is terrestrial testing with lunar dust simulants. Dust has a stochastic nature of depositing and it can be difficult to accurately apply it to surfaces of interest. Deposition density, particles size distribution, and percent coverage are all factors that affect the quality of dust mitigation testing. Therefore, to enable such testing the dust mitigation and seals teams at NASA Glenn Research Center (GRC) have developed a system that can uniformly and repeatably deposit lunar simulants on a range of surfaces. Testing of the Dust Deposition System (DDS) and an associatedsimulant preparation methodology have quantified the levels of uniformity and precision for this system. Furthermore, the deposition system has been paired with automated micrograph capturing and machine learning image analysis to correlate the images of dust on a surface to deposition density (in g/cm2). This correlation alleviates the need for tested samples to be accurately weighed with milligram precision and may be a useful tool for in-situ contamination evaluation on the Moon. This paper covers the design and validation testing for the DDS.

Stephen Gerdts↗
DOE OSTI2021

Simple, Secure, Internet Delivery of MOOSE-based Applications

Application packaging and distribution are the final steps for delivering software to end-users; both are frequently neglected when creating scientific software. Commercial businesses rely on electronic distribution systems that have rendered disk drives obsolete. Still, national laboratories continue to rely heavily on removable media to distribute and limit access to controlled applications. With increasing concerns of unauthorized copying of sensitive applications, a modern distribution system that utilizes cryptographically secure communication and authentication protocols has been developed. This new distribution system will secure the chain of custody for nuclear software while simultaneously simplifying access to these tools. This report summarizes four primary advancements made toward the secure distribution of Nuclear Energy Advanced Modeling and Simulation (NEAMS)-developed, Multiphysics Object Oriented Simulation Environment (MOOSE)-based applications: application installation, package distribution, automated package building, and distribution of documentation. NEAMS is currently developing more than ten separate applications based on the open-source MOOSE Framework. Distribution of these applications has primarily been accomplished by distributing source code, with end-users compiling the applications themselves. This work created a mechanism where MOOSE applications can be installed in a similar way to any other software. This allows both administrators and end-users simplified access to runnable executables. With this new installation capability, it was then possible to rethink distribution. A new, secure capability for delivering MOOSE-based applications over the internet has been created. This system requires unique cryptographic tokens for authentication, greatly securing the custody chain for software. Once granted access, installation of any NEAMS code can be accomplished with these terminal commands: "conda install ncrc" "ncrc install ncrc-bison." After these two commands (and authenticating) the BISON application will be securely down- loaded from Idaho National Laboratory (INL)’s servers, installed, and ready to use. To enable this new distribution capability to be successful, the open-source Continuous Integration, Verification, Enhancement, and Testing (CIVET) Continuous Integration (CI) capability was augmented to add Continuous Delivery (CD). CD enables the automated building and packaging of MOOSE-based applications as they are modified by development teams, ensuring that our customers can obtain up-to-date versions of the software at any time. The need for instruction on how to use these applications was addressed through modifications to the MOOSE documentation system. The MooseDocs capability, which enables robust documentation of MOOSE-based applications, has been extended to allow both for the installation of documentation and the packaging of documentation with installed applications. Together, these enhancements form the core of a new, secure distribution mechanism for nuclear simulation tools. In concert with the Nuclear Computational Resource Center (NCRC), NEAMS- developed applications will now be straightforward to obtain securely.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1992

Methodology for sensitivity analysis, approximate analysis, and design optimization in CFD for multidisciplinary applications

Fundamental equations of aerodynamic sensitivity analysis and approximate analysis for the two dimensional thin layer Navier-Stokes equations are reviewed, and special boundary condition considerations necessary to apply these equations to isolated lifting airfoils on 'C' and 'O' meshes are discussed in detail. An efficient strategy which is based on the finite element method and an elastic membrane representation of the computational domain is successfully tested, which circumvents the costly 'brute force' method of obtaining grid sensitivity derivatives, and is also useful in mesh regeneration. The issue of turbulence modeling is addressed in a preliminary study. Aerodynamic shape sensitivity derivatives are efficiently calculated, and their accuracy is validated on two viscous test problems, including: (1) internal flow through a double throat nozzle, and (2) external flow over a NACA 4-digit airfoil. An automated aerodynamic design optimization strategy is outlined which includes the use of a design optimization program, an aerodynamic flow analysis code, an aerodynamic sensitivity and approximate analysis code, and a mesh regeneration and grid sensitivity analysis code. Application of the optimization methodology to the two test problems in each case resulted in a new design having a significantly improved performance in the aerodynamic response of interest.

Taylor, Arthur C., III↗
NASA NTRSDate not supplied

Demonstration of A Long Duration Crop in the Advanced Plant Habitat Engineering Demonstration Unit: Key Factors to Consider Prior to Testing and Lessons Learned

The Advanced Plant Habitat (APH) is a fully enclosed, closed-loop, plant growth facility currently deployed on the International Space Station (ISS). It is equipped with complete environmental control (i.e.spectral qualityandlight intensity, temperature, relative humidity, and CO2),root module which containsa growth substrate(typically arcillite) and a porous tube based automated water delivery system. Two APH units, one ground unitidentical to the on-orbit versionand an Engineering Development Unit (EDU; a high fidelity test version), currently reside at Kennedy Space Center. Prior to conducting tests on-orbit, these APH ground units areutilized to conductbothScience Verification Tests(SVT; primarilyinthe EDU) and Experiment Verification Tests (EVT; primarily in the Ground Unit). In February 2020, a 122 day experiment was concluded in the APH EDU where four 'Numex Española Improved' pepper plants (Capsicum annuum) were successfully grown from seed to harvestyieldingover 50 fruit, demonstrating the capabilityand versatilityof this APH EDU system to support plant growth for long life cycle flowering/fruiting plants.

L. E. Spencer↗
NASA NTRS2021

System Analysis and Generative Design for Icenode, a Buoyant Vehicle for Measuring Melt Rate Under Ice Shelves

Antarctic ice shelves buttress the Antarctic Ice Sheet from sliding into the ocean, and their collapse could trigger a meter or more of global sea level rise by the end of the century. Current state-of-the-art predictions for ice shelf behavior in a warming climate have large uncertainty, significantly hindered by a lack of in situ melt rate observations under ice shelves, especially near grounding zones. IceNode is a novel robotic vehicle under development at the NASA Jet Propulsion Laboratory to acquire such measurements, but presents a complex design problem owing to the large design space and conflicting performance requirements. Evaluating a preliminary design requires several types of tedious analysis which prevents rapid iteration and exploration of the design space. We present the implementation of a custom system analysis framework which was used to automate analysis such as resource budgeting, mission simulation, mass and buoyancy balancing, and static landing stability analysis of a given design configuration. Using this framework, we selected parameters which had the largest effects on design success and conducted a generative design study in which we programmatically varied a handful of parameters to generate 1540 different design candidates and test them across 160 different environmental scenarios. The custom built system analysis tool enabled rapid development of critical analysis and automated exploration of a large design space to guide preliminary design of the IceNode vehicle.

Gebara, Christine↗
DOE OSTI2013

Automated fibroglandular tissue segmentation and volumetric density estimation in breast MRI using an atlas-aided fuzzy C-means method

Purpose: Breast magnetic resonance imaging (MRI) plays an important role in the clinical management of breast cancer. Studies suggest that the relative amount of fibroglandular (i.e., dense) tissue in the breast as quantified in MR images can be predictive of the risk for developing breast cancer, especially for high-risk women. Automated segmentation of the fibroglandular tissue and volumetric density estimation in breast MRI could therefore be useful for breast cancer risk assessment. Methods: In this work the authors develop and validate a fully automated segmentation algorithm, namely, an atlas-aided fuzzy C-means (FCM-Atlas) method, to estimate the volumetric amount of fibroglandular tissue in breast MRI. The FCM-Atlas is a 2D segmentation method working on a slice-by-slice basis. FCM clustering is first applied to the intensity space of each 2D MR slice to produce an initial voxelwise likelihood map of fibroglandular tissue. Then a prior learned fibroglandular tissue likelihood atlas is incorporated to refine the initial FCM likelihood map to achieve enhanced segmentation, from which the absolute volume of the fibroglandular tissue (|FGT|) and the relative amount (i.e., percentage) of the |FGT| relative to the whole breast volume (FGT%) are computed. The authors' method is evaluated by a representative dataset of 60 3D bilateral breast MRI scans (120 breasts) that span the full breast density range of the American College of Radiology Breast Imaging Reporting and Data System. The automated segmentation is compared to manual segmentation obtained by two experienced breast imaging radiologists. Segmentation performance is assessed by linear regression, Pearson's correlation coefficients, Student's pairedt-test, and Dice's similarity coefficients (DSC). Results: The inter-reader correlation is 0.97 for FGT% and 0.95 for |FGT|. When compared to the average of the two readers’ manual segmentation, the proposed FCM-Atlas method achieves a correlation ofr = 0.92 for FGT% and r = 0.93 for |FGT|, and the automated segmentation is not statistically significantly different (p = 0.46 for FGT% and p = 0.55 for |FGT|). The bilateral correlation between left breasts and right breasts for the FGT% is 0.94, 0.92, and 0.95 for reader 1, reader 2, and the FCM-Atlas, respectively; likewise, for the |FGT|, it is 0.92, 0.92, and 0.93, respectively. For the spatial segmentation agreement, the automated algorithm achieves a DSC of 0.69 ± 0.1 when compared to reader 1 and 0.61 ± 0.1 for reader 2, respectively, while the DSC between the two readers’ manual segmentation is 0.67 ± 0.15. Additional robustness analysis shows that the segmentation performance of the authors' method is stable both with respect to selecting different cases and to varying the number of cases needed to construct the prior probability atlas. The authors' results also show that the proposed FCM-Atlas method outperforms the commonly used two-cluster FCM-alone method. The authors' method runs at ∼5 min for each 3D bilateral MR scan (56 slices) for computing the FGT% and |FGT|, compared to ∼55 min needed for manual segmentation for the same purpose. Conclusions: The authors' method achieves robust segmentation and can serve as an efficient tool for processing large clinical datasets for quantifying the fibroglandular tissue content in breast MRI. It holds a great potential to support clinical applications in the future including breast cancer risk assessment.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
NASA NTRSDate not supplied

Uniform Dust Deposition System for Dust Tolerance Studies

Future missions to the Moon will require mechanisms and materials to effectively and reliably operate in the presences of lunar regolith. One of the challenges of developing such technologies is terrestrial testing with lunar dust simulants. Dust has a stochastic nature of depositing and it can be difficult to accurately apply it to surfaces of interest. Deposition density, particles size distribution, and percent coverage are all factors that affect the quality of dust mitigation testing. Therefore, to enable such testing the dust mitigation and seals teams at NASA Glenn Research Center (GRC) have developed a system that can uniformly and repeatably deposit lunar simulants on a range of surfaces. Testing of the Dust Deposition System (DDS) and an associated simulant preparation methodology have quantified the levels of uniformity and precision for this system. Furthermore, the deposition system has been paired with automated micrograph capturing and machine learning image analysis to correlate the images of dust on a surface to deposition density (in g/cm2). This correlation alleviates the need for tested samples to be accurately weighed with milligram precision and may be a useful tool for in-situ contamination evaluation on the Moon. This paper covers the design and validation testing for the DDS.

Dust↗
NASA NTRS2017

Development of a High-Fidelity Simulation Environment for Shadow-Mode Assessments of Air Traffic Concepts

This paper describes the Shadow-Mode Assessment Using Realistic Technologies for the National Airspace System (SMART-NAS) Test Bed. The SMART-NAS Test Bed is an air traffic simulation platform being developed by the National Aeronautics and Space Administration (NASA). The SMART-NAS Test Bed's core purpose is to conduct high-fidelity, real-time, human-in-the-loop and automation-in-the-loop simulations of current and proposed future air traffic concepts for the United States' Next Generation Air Transportation System called NextGen. The setup, configuration, coordination, and execution of realtime, human-in-the-loop air traffic management simulations are complex, tedious, time intensive, and expensive. The SMART-NAS Test Bed framework is an alternative to the current approach and will provide services throughout the simulation workflow pipeline to help alleviate these shortcomings. The principle concepts to be simulated include advanced gate-to-gate, trajectory-based operations, widespread integration of novel aircraft such as unmanned vehicles, and real-time safety assurance technologies to enable autonomous operations. To make this possible, SNTB will utilize Web-based technologies, cloud resources, and real-time, scalable, communication middleware. This paper describes the SMART-NAS Test Bed's vision, purpose, its concept of use, and the potential benefits, key capabilities, high-level requirements, architecture, software design, and usage.

human-in-the-loop↗
NASA NTRS2017

Development of a High-Fidelity Simulation Environment for Shadow-Mode Assessments of Air Traffic Concepts

This paper will describe the purpose, architecture, and implementation of a gate-to-gate, high-fidelity air traffic simulation environment called the Shadow Mode Assessment using Realistic Technologies for the National Airspace System (SMART-NAS) Test Bed.The overarching purpose of the SMART-NAS Test Bed (SNTB) is to conduct high-fidelity, real-time, human-in-the-loop and automation-in-the-loop simulations of current and proposed future air traffic concepts for the Next Generation Air Transportation System of the United States, called NextGen. SNTB is intended to enable simulations that are currently impractical or impossible for three major areas of NextGen research and development: Concepts across multiple operational domains such as the gate-to-gate trajectory-based operations concept; Concepts related to revolutionary operations such as the seamless and widespread integration of large and small Unmanned Aerial System (UAS) vehicles throughout U.S. airspace; Real-time system-wide safety assurance technologies to allow safe, increasingly autonomous aviation operations. SNTB is primarily accessed through a web browser. A set of secure support services are provided to simplify all aspects of real-time, human-in-the-loop and automation-in-the-loop simulations from design (i.e., prior to execution) through analysis (i.e., after execution). These services include simulation architecture and asset configuration; scenario generation; command, control and monitoring; and analysis support.

human-in-the-loop↗
DOE OSTI2024

Optimization and Evaluation of Energy Savings for Connected and Autonomous Off-Road Vehicles

Off-road vehicles, such as wheel loaders, excavators, and harvesters, are extensively utilized across a wide range of industries, including construction, agriculture, and mining. These machines have become indispensable in supporting the day-to-day operational needs of a nation, playing a critical role in various sectors' infrastructure and productivity. However, despite their utility, off-road vehicles are significant consumers of fossil fuels, resulting in substantial emissions that contribute to environmental degradation. This highlights the pressing need for research and technological advancements aimed at improving their energy efficiency and reducing their carbon footprint. There are, however, two primary challenges that must be addressed to achieve these goals. First, off-road vehicles typically perform both driving and working tasks simultaneously, which introduces a high level of complexity into their overall dynamic systems. Analysis the interactions between these functions is challenging. Second, research into off-road vehicles is inherently interdisciplinary, demanding expertise across several domains such as fluid power systems, vehicle dynamics, control theory, optimization techniques, and real-world implementation. Recognizing these challenges, we proposed the project titled "Optimization and Evaluation of Energy Savings for Connected and Autonomous Off-Road Vehicles" as a comprehensive solution to enhance fuel efficiency while simultaneously improving productivity. This project specifically focuses on autonomous off-road vehicles, with particular attention to wheel loaders, and seeks to develop novel methods to optimize energy consumption without sacrificing operational performance. The project integrates real-time control algorithms, vehicle dynamics modeling, and co-optimization of powertrain system and vehicle system to achieve these goals. Our optimization strategy dynamically co-optimizes critical parameters at both the powertrain and vehicle levels, including vehicle speed, working tool movements, powertrain dynamics, and engine operations in real-time. To streamline this optimization process, we developed a vehicle model that captures the key dynamics while significantly enhancing computational efficiency. This allows the system to intelligently minimize fuel consumption, all while maintaining or even improving productivity through real-time calculations during various off-road operations. To validate the effectiveness of this energy optimization method, we introduced a state-of-the-art Hardware-in-the-Loop (HIL) testbed. This reconfigurable testbed seamlessly integrates the actual engine with virtual models of the wheel loader's subsystems, allowing for accurate emulation of real-world operational loads and environments. By simulating these conditions, the HIL testbed enables us to evaluate the wheel loader’s performance under diverse working scenarios, ensuring the developed solution is applicable in real-world operations. This testbed proved to be instrumental in validating the optimization algorithms and demonstrating the system's practical effectiveness. During the evaluation and testing phase, we employed the HIL testbed to rigorously assess the energy savings and productivity improvements generated by the optimized system. The results were highly encouraging, revealing that the automated wheel loader achieved over 30% fuel savings compared to traditional, human-operated cycles, with comparable or even enhanced levels of productivity. The insights gained from this HIL-based testing provided critical validation of our approach and highlighted the potential for deploying these optimized autonomous technologies in real-world off-road vehicles.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Evaluation of Machine Learning Models for Automated Data Analysis in In-Service Nuclear Power Plant Inspections

The commercial nuclear power industry is facing a potential shortage of certified nondestructive evaluation (NDE) analysts to meet future in-service inspection demands. Automated data analysis (ADA) currently supports human inspectors in tasks such as eddy current evaluations for steam generator examinations. Machine learning (ML) systems are nearing the capability to pass performance demonstration tests for ultrasonic testing (UT) inspections of reactor pressure vessel upper head penetrations in nuclear power plants (NPPs). Current research and development is focused on assisted analysis (AA) of ADA versus fully automated examinations. This presentation will cover assessment of ML flaw detection on dissimilar metal weld (DMW) piping joints.

36 MATERIALS SCIENCE↗