Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thrust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Jet Propulsion with Special Reference to Thrust Augmenters

An investigation of the possibility of using thrust augmented jets as prime movers was carried out. The augmentation was to be effected by allowing the jet to mix with the surrounding air in the presence of bodies which deflect the air set in motion by the jet.

Schubauer, G B↗

Investigation of the Liquid Fluorine-liquid Diborane Propellant Combination in a 100-pound-thrust Rocket Engine

The experimental performance of liquid fluorine and liquid diborane was investigated in a 100-pound-thrust engine at a combustion pressure of 300 pounds per square inch absolute. Methods of handling and transporting liquid fluorine were developed. It was extremely difficult to obtain satisfactory operation because of the high flame speed and high combustion chamber temperatures. The maximum performance obtained was 280 pound seconds per pound, 88 percent of the theoretical maximum. The theoretical performance was recalculated with revised thermodynamic data, indicating a maximum specific impulse of 311 pound seconds per pound as compared with the previously reported value of 323.

COMBUSTION - ROCKET ENGINES↗

Simulated afterburner performance with hydrogen peroxide injection for thrust augmentation

Combustion performance of three afterburner configurations was evaluated at simulated altitude flight conditions with liquid augmentation to the primary combustor. Afterburner combustion efficiency and stability were better with injection of high-strength hydrogen peroxide than with no injection or with water injection. Improvements were observed in afterburner configurations with and without flameholders and in a short-length afterburner. At a peroxide-air ratio of 0.3, combustion was stable and 85 to 90 percent efficient in all configurations tested. Calculated augmented net-thrust ratios for peroxide injection with afterburning were approximately 60 percent greater than those for water injection.

Metzler, Allen J↗

Static Thrust and Power Characteristics of Six Full-Scale Propellers

Static thrust and power measurements were made of six full-scale propellers. The propellers were mounted in front of a liquid-cooled-engine nacelle and were tested at 15 different blade angles in the range from -7 1/2 degrees to 35 degrees at 0.75r. The test rig was located outdoors and the tests were made under conditions of approximately zero wind velocity.

Hartman, Erwin P↗

Plastic buckling of a rectangular plate under edge thrusts

The fundamental equations for the plastic buckling of a rectangular plate under edge thrusts are developed on the basis of a new set of stress-strain relations for the behavior of a metal in the plastic range. These relations are derived for buckling from a state of uniform compression. The fundamental equation for the buckling of a simply compressed plate together with typical boundary conditions is then developed and the results are applied to calculating the buckling loads of a thin strip, a simply supported plate, and a cruciform section. Comparisons with the theories of Timoshenko and Ilyushin are made. Finally, an energy method is given which can be used for finding approximate values of the critical load.

Handelman, G H↗

Analysis of thrust augmentation of turbojet engines by water injection at compressor inlet including charts for calculating compression processes with water injection

A psychrometric chart having total pressure (sum of partial pressures of air and water vapor) as a variable, a Mollier diagram for air saturated with water vapor, and charts showing the thermodynamic properties of various air-water vapor and exhaust gas-water vapor mixtures are presented as aids in calculating the thrust augmentation of a turbojet engine resulting from the injection of water at the compressor inlet. Curves are presented that show the theoretical performance of the augmentation method for various amounts of water injected and the effects of varying flight Mach number, altitude, ambient-air temperature, ambient relative humidity, compressor pressure ratio, and inlet-diffuser efficiency. Numerical examples, illustrating the use of the psychrometric chart and the Mollier diagram in calculating both compressor-inlet and compressor-outlet conditions when water is injected at the compressor inlet, are presented.

Wilcox, E Clinton↗

A Wind-Tunnel Investigation of the Effects of Thrust-Axis Inclination on Propeller First-Order Vibration

Data on the aerodynamic excitation of first-order vibration occurring in a representative three-blade propeller having its thrust axis inclined to the airstream at angles of 0 degree, 4.55 degrees, and 9.80 degrees are included in this report. For several representative conditions the aerodynamic excitation has been computed and compared with the measured values. Blade stresses also were measured to permit the evaluation of the blade stress resulting from a given blade aerodynamic excitation. It was concluded that the section aerodynamic exciting force of a pitched propeller may be computed accurately at low rotational speeds. As section velocities approach the speed of sound, the accuracy of computation of section aerodynamic exciting force is not always so satisfactory.

Gray, W H↗

An Analysis of Once-per-revolution Oscillating Aerodynamic Thrust Loads on Single-Rotation Propellers on Tractor Airplanes at Zero Yaw

A simplified procedure is shown for calculating the once-per-revolution oscillating aerodynamic thrust loads on propellers of tractor airplanes at zero yaw. The only flow field information required for the application of the procedure is a knowledge of the upflow angles at the horizontal center line of the propeller disk. Methods are presented whereby these angles may be computed without recourse to experimental survey of the flow field. The loads computed by the simplified procedure are compared with those computed by a more rigorous method and the procedure is applied to several airplane configurations which are believed typical of current designs. The results are generally satisfactory.

Rogallo, Vernon L↗

An Investigation of Single- and Dual-Rotation Propellers at Positive and Negative Thrust, and in Combination with an NACA 1-series D-Type Cowling at Mach Numbers up to 0.84

An investigation has been made to determine the aerodynamic characteristics of the NACA 4-(5)(05)-041 four-blade, single-relation propeller and the NACA 4-(5)(05)-037 six- and eight-blade, dual-rotation propellers in combination with various spinners and NACA d-type spinner-cowling combinations at Mach numbers up to 0.84. Propeller force characteristics, local velocity distributions in the propeller planes, inlet pressure recoveries, and static-pressure distributions on the cowling surfaces were measured for a wide range of blade angles, advance ratios, and inlet-velocity ratios. Included are data showing: (a) the effect of extended cylindrical spinners on the characteristics of the single-rotation propeller, (b) the effect of variation of the difference in blade angle setting between the front and rear components of the dual-rotation propellers, (c) the negative- and static-thrust characteristics of the propellers with 1 series spinners, and (d) the effects of ideal- and platform-type propeller-spinner junctures on the pressure-recovery characteristics of the single-rotation propeller-spinner-cowling combination.

Reynolds, Robert M↗

Altitude-wind-tunnel investigation of a 4000-pound-thrust axial-flow turbojet engine VI : combustion-chamber performance

An analysis of the performance of the types A, B, and C combustion chambers of the 4000-pound-thrust axial-flow turbojet engine is presented. The data were obtained from investigations of the complete engine over a range of pressure altitudes from 5000 to 40,000 feet and ram pressure ratios from 1.00 to 1.86. The combustion-chamber pressure losses, the effect of the losses on cycle efficiency, and the combustion efficiency are discussed.

Pinkel, I Irving↗

A wind-tunnel investigation of the effects of thrust-axis inclination on propeller first-order vibration

Data on the aerodynamic excitation of first-order vibration occurring in a representative three-blade propeller having its thrust axis inclined to the air stream at angles of 0 degrees, 4.55 degrees, and 9.8 degrees are included in this paper. For several representative conditions the aerodynamic excitation has been computed and compared with the measured values. Blade stresses also were measured to permit the evaluation of the blade stress resulting from a given blade aerodynamic excitation. It was concluded that the section aerodynamic exciting force of a pitched propeller may be computed accurately at low rotational speeds. As section velocities approach the speed of sound, the accuracy of computation of section aerodynamic exciting force is not always so satisfactory. First-order blade vibratory stresses were computed with satisfactory accuracy from untilted-propeller loading data. A stress prediction which assumes a linear relation between first-order vibratory stress and the product of pitch angle and dynamic pressure and which is based on stresses at low rotational speeds will be conservative when the outer portions of the blade are in the transonic and low supersonic speed range.

Gray, W H↗

Take-off and propeller thrust

As a result of previous reports, it was endeavored to obtain, along with the truest possible comprehension of the course of thrust, a complete, simple and clear formula for the whole take-off distance up to a certain altitude, which shall give the correct relative weight to all the factors.

Schrenk, Martin↗

Static internal performance of a single expansion ramp nozzle with multiaxis thrust vectoring capability

An investigation was conducted at static conditions in order to determine the internal performance characteristics of a multiaxis thrust vectoring single expansion ramp nozzle. Yaw vectoring was achieved by deflecting yaw flaps in the nozzle sidewall into the nozzle exhaust flow. In order to eliminate any physical interference between the variable angle yaw flap deflected into the exhaust flow and the nozzle upper ramp and lower flap which were deflected for pitch vectoring, the downstream corners of both the nozzle ramp and lower flap were cut off to allow for up to 30 deg of yaw vectoring. The effects of nozzle upper ramp and lower flap cutout, yaw flap hinge line location and hinge inclination angle, sidewall containment, geometric pitch vector angle, and geometric yaw vector angle were studied. This investigation was conducted in the static-test facility of the Langley 16-Foot Transonic Tunnel at nozzle pressure ratios up to 8.0.

Capone, Francis J.↗

Evaluation of dual flow thrust vector nozzles with exhaust stream impingement

To supplement previous work performed by NASA, a cold-jet facility was established at the California Polytechnic State University, San Luis Obispo campus. The purpose of this facility is to continue the studies of cold flow multiaxis thrust vectoring conducted at the NASA Langley Research Center. A single nozzle test apparatus was completed and is presently operational. Included are the results of the single flow test envelope that was requested by NASA personnel. Details about the test apparatus are included in the Cal Poly Semi-Annual Progress report.

Carpenter, Thomas W.↗

Computational analysis of Variable Thrust Engine (VTE) performance

The Variable Thrust Engine (VTE) of the Orbital Maneuvering Vehicle (OMV) uses a hypergolic propellant combination of Monomethyl Hydrazine (MMH) and Nitrogen Tetroxide (NTO) as fuel and oxidizer, respectively. The performance of the VTE depends on a number of complex interacting phenomena such as atomization, spray dynamics, vaporization, turbulent mixing, convective/radiative heat transfer, and hypergolic combustion. This study involved the development of a comprehensive numerical methodology to facilitate detailed analysis of the VTE. An existing Computational Fluid Dynamics (CFD) code was extensively modified to include the following models: a two-liquid, two-phase Eulerian-Lagrangian spray model; a chemical equilibrium model; and a discrete ordinate radiation heat transfer model. The modified code was used to conduct a series of simulations to assess the effects of various physical phenomena and boundary conditions on the VTE performance. The details of the models and the results of the simulations are presented.

Giridharan, M. G.↗

Thrust augmentation options for the Beta 2 two-stage-to-orbit vehicle

NASA LeRC is continuing to study propulsion concepts for a horizontal takeoff and landing, fully reusable, two-stage-to-orbit vehicle. This will be capable of launching and returning a 10,000 pound payload to a 100 nautical mile polar orbit using low-risk technology. The vehicle, Beta 2, is a derivative of the USAF/Boeing Beta vehicle which was designed to deliver a 50,000 pound payload to a similar orbit. Beta 2 stages at Mach 6.5 and about 100,000 ft altitude. The propulsion system for the booster is an over/under turbine bypass engine/ramjet configuration. In this paper, several options for thrust augmentation were studied in order to improve the performance of this engine where there was a critical need. Options studies were turbine engine overspeed in the transonic region, water injection at a various turbine engine locations also during the transonic region, and water injection at the turbine engine face during high speed operation. The methodology, constraints, propulsion performance, and mission study results are presented.

Snyder, Christopher A.↗

Options for thrust augmentation for the Beta 2 two-stage-to-orbit launch vehicle

A study to improve the performance of the NASA two-stage-to-orbit vehicle was undertaken. The NASA concept, a horizontal takeoff and landing, fully reusable, two-stage to orbit vehicle, will be capable of launching and returning a 10,000 pound payload to a 100 nmi polar orbit. The vehicle, Beta 2, is a derivative of the USAF/Boeing Beta vehicle which was designed to deliver a 50,000 pound payload to a similar orbit. Beta 2 stages at Mach 6.5 and about 100,000 feet altitude. The propulsion system for the booster is an over/under turbine engine/ramjet configuration. In this paper a study was performed for one of the candidate engines, the variable cycle engine, to assess its potential to meet the required performance needs of the Beta 2 vehicle. Several options for thrust augmentation were studied in order to improve the performance of the engine where there was a critical need. The methodology, constraints, propulsion performance, and mission study results are presented.

Jules, Kenol↗

Orbital transfer rocket engine technology 7.5K-LB thrust rocket engine preliminary design

A preliminary design of an advanced LOX/LH2 expander cycle rocket engine producing 7,500 lbf thrust for Orbital Transfer vehicle missions was completed. Engine system, component and turbomachinery analysis at both on design and off design conditions were completed. The preliminary design analysis results showed engine requirements and performance goals were met. Computer models are described and model outputs are presented. Engine system assembly layouts, component layouts and valve and control system analysis are presented. Major design technologies were identified and remaining issues and concerns were listed.

Harmon, T. J.↗