Laser Irradiation Induced Atomic Structure Modifications in Strontium Titanate
Not provided.
Materials Science↗
SEARCH · Engineering Papers
Results for “laser processing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Temperature-dependent growth of hexagonal and monoclinic gallium sulfide films by pulsed-laser deposition
We demonstrate the selective, pulsed-laser deposition of hexagonal GaS and monoclinic Ga2S3 films on sapphire substrates from a single Ga 2 S 3 target in high-vacuum conditions. Growth at substrate temperatures below 550 °C causes GaS film formation, which indicates non-stoichiometric transfer from the target to the film. Surprisingly, stoichiometric transfer occurs at substrate temperatures above 650 °C with monoclinic Ga 2 S 3 as the preferred, higher S-content phase. Through a series of growth and annealing experiments, we show that GaS nucleation under S-deficient conditions leads to the preferred growth of this layered, hexagonal phase below 550 °C. Furthermore, GaS films annealed above 650 °C under high vacuum are transformed to Ga 2 S 3 , reflecting the greater stability of the monoclinic phase. By first growing Ga 2 S 3 at a higher temperature and subsequently growing GaS at a lower temperature, we can fabricate GaS/Ga 2 S 3 heterostructures in a single growth process.
36 MATERIALS SCIENCE↗
Development of Quantum Interconnects (QuICs) for Next-Generation Information Technologies
Just as “classical” information technology rests on a foundation built of interconnected information-processing systems, quantum information technology (QIT) must do the same. A critical component of such systems is the “interconnect,” a device or process that allows transfer of information between disparate physical media, for example, semiconductor electronics, individual atoms, light pulses in optical fiber, or microwave fields. While interconnects have been well engineered for decades in the realm of classical information technology, quantum interconnects (QuICs) present special challenges, as they must allow the transfer of fragile quantum states between different physical parts or degrees of freedom of the system. The diversity of QIT platforms (superconducting, atomic, solid-state color center, optical, etc.) that will form a “quantum internet” poses additional challenges. As quantum systems scale to larger size, the quantum interconnect bottleneck is imminent, and is emerging as a grand challenge for QIT. For these reasons, it is the position of the community represented by participants of the NSF workshop on “Quantum Interconnects” that accelerating QuIC research is crucial for sustained development of a national quantum science and technology program. Given the diversity of QIT platforms, materials used, applications, and infrastructure required, a convergent research program including partnership between academia, industry, and national laboratories is required.
71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
Photodissociation dynamics of the tert -butyl perthiyl radical
Here, the photodissociation dynamics of the tert-butyl perthiyl (t-BuSS) radical are investigated by fast-beam coincidence translational spectroscopy. A fast (6 keV-8 keV) beam of neutral t-BuSS radicals is produced via photodetachment of the corresponding anion, followed by photodissociation at 248 nm (5.00 eV) or 193 nm (6.42 eV) and coincident detection of the neutral products. Photofragment mass and translational energy distributions are obtained at both wavelengths. At 248 nm, the dominant product channel (90%) is found to be S loss, with a product translational energy distribution that peaks close to the maximum available energy and an anisotropic photofragment angular distribution, indicating dissociation along a repulsive excited state. A minor channel (10%) leading to the formation of S 2 + t-Bu is also observed. At 193 nm, both two- and three-body dissociation are observed. The formation of S 2 + t-Bu is the dominant two-body product channel, with multiple electronic states of the S 2 molecule produced via excited-state dissociation processes. The formation of S + t-BuS is a minor two-body channel at this dissociation energy. The three-body channels are S 2 + H + isobutene, S 2 + CH 3 + propene, and S + SH + isobutene. The first two of these channels result from a sequential dissociation process in which the loss of S 2 from t-BuSS results in ground-state t-Bu with sufficient internal energy to undergo secondary fragmentation. The third three-body channel, S + SH + isobutene, is attributed to the loss of internally excited HS 2 from t-BuSS, which then rapidly dissociates to form S + SH in an asynchronous concerted dissociation process.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Self-Trapped-Exciton Radiative Recombination in β–Ga 2 O 3 : Impact of Two Concurrent Nonradiative Auger Processes
The peculiarities of radiative and nonradiative processes associated with self-trapped intrinsic eXcitons in the excited β-Ga 2 O 3 crystals are studied via time-resolved techniques of induced absorption, transient grating, and photoluminescence (PL) at room temperature. The excitation above the bandgap is produced by laser pulses with linear light polarization parallel and orthogonal in the (–201) and (001) planes. We elucidate that the nonradiative recombination rate occurring in the eXciton prevails over its radiative emission rate in a wide range of free carrier concentration composed of excited and equilibrium electrons. Hence, the nonradiative recombination has no effect on the strong anisotropy and the shape of the eXciton emission band. However, we find out that the conventional ABC model of electron effective lifetime is insufficient for explanation of the excitation dependences. Inclusion of two nonradiative Auger mechanisms in a modified ABC formula provides excellent agreement of these dependences. We conclude that the trap-assisted Auger process is in proportion to the free electron density with coefficient B = 1.1 × 10 –11 cm 3 /s and appears at low/intermediate excitation, while the triple-particle Auger process is in proportion to Δn 2 with coefficient C = 8 × 10 –30 cm 6 /s and appears at high excitation conditions. The transition between two Auger mechanisms is accompanied by a rise of the eXciton diffusivity in preferred crystallographic directions where the radiative PL intensity is maximal. The diffusion length LD in these directions can reach values ~300 nm, but, at high excitations, LD becomes limited by Auger lifetimes. These findings pave the way for the implementation of self-trapped eXcitons into specific optoelectronic devices.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Registration and fusion of large-scale melt pool temperature and morphology monitoring data demonstrated for surface topography prediction in LPBF
In-situ monitoring technologies for laser powder bed fusion (LPBF) additive manufacturing often face one key challenge, extracting the ultrafast melt pool (MP) signatures for understanding the localized part properties. Further, the spatial information of each monitored MP signature is essential for correlating the MP – part property. This spatial information is often unavailable especially from commercial LPBF printers. Many MP monitoring methods have been reported and utilized. However, very few of these have the MP’s spatial information. To overcome this challenge, in this work we report a method for spatially registering the key MP signatures (MP intensity, temperature, and area) to the monitored print parts. The MP signatures are obtained from our coaxial high-speed single-camera based two-wavelength imaging pyrometry (STWIP) system and the MP spatial information is obtained from an off-axis camera system. A machine learning aided image analysis method is employed to retrieve the spatial distribution of MPs within the corresponding part’s coordinates system. Then, the MP signature maps (MPSMs) are reconstructed by mapping the STWIP measured MP signatures to the registered MP coordinates. Further, a long short-term memory (LSTM) neural network is developed for estimating the layer surface topography from the registered MPSMs. The obtained results indicate that the layer surface topography can be more accurately estimated by using MP temperature signature rather than MP intensity and/or area signatures as in common practice. Finally, our developed methods for MP monitoring, registration, and MP-surface topography prediction offer advanced capabilities for the online detection of process anomalies and part defects.
36 MATERIALS SCIENCE↗
Improved Productivity with Multilaser Rotary Powder Bed Fusion Additive Manufacturing
Laser powder bed fusion (LPBF) enables the fabrication of intricate, geometrically complex structures with a sufficiently fine surface finish for many engineering applications with a diversity of available feedstock metals. However, the production rate of LPBF systems is not well suited for mass production in comparison to traditional manufacturing methods. LPBF systems measure their deposition rates in 100's of grams per hour, while other processes measure in kilograms per hour or even in the case of processes such as forming, stamping, and casting, 100's of kilograms per hour. To be widely adopted in industry for mass production, LPBF requires a new scalable architecture that enables many orders of magnitude improvement in deposition rate, while maintaining the geometry freedom of additive manufacturing. This article explores concepts that could achieve as much as four orders of magnitude increase in the production rate through the application of (1) rotary table kinematic arrangements; (2) a dramatic number of simultaneously operating lasers; (3) reductions of laser optic size; (4) improved scanning techniques; and (5) an optimization of toroidal build plate size. To theoretically demonstrate the possibilities of production improvements, a productivity analysis is proposed for synchronous reluctance motors with relevance to the electric vehicle industry, given the recent increase in the diversity of printable soft magnetic alloys. The analysis provides insights into the impact of the architecture and process parameters necessary to optimize rotary powder bed fusion for mass production.
36 MATERIALS SCIENCE↗
Tempering kinetics during multilayer laser additive manufacturing of a ferritic steel
Grade 91 steel forms martensite during additive manufacturing and the extent of tempering of martensite significantly affects the mechanical properties of parts. Currently, there is a lack of quantitative understanding of the tempering kinetics for Grade 91 steel, and as a result, the effects of repeated thermal cycles on properties for different processing conditions cannot be determined. Here we evaluate the tempering kinetics by determining the constant terms in the Johnson Mehl Avrami kinetic equation from the tempering data available in the literature and the thermal cycles computed using a rigorously-tested heat and fluid flow model of multi-layer additive manufacturing. The raw tempering data are cleaned using a neural network to enhance accuracy. The lower layers experience repeating cycles of heating and cooling when the upper layers are added. As a result, the hardness is reduced owing to the tempering of martensite. In contrast, martensite formed in the upper layers is not tempered to the same extent and the hardness remains high. Therefore, the hardness of the part increases with the distance from the substrate. Variations in the heat input at different laser powers and scanning speeds significantly affect the extent of tempering. Finally, since the method used here can provide a quantitative understanding of the tempering of martensite and the spatial variation in hardness, it can be used to tailor the microstructure and hardness of heat treatable printed metallic parts.
36 MATERIALS SCIENCE↗
The X-Ray Emission Effectiveness of Plasma Mirrors: Reexamining Power-Law Scaling for Relativistic High-Order Harmonic Generation
Ultrashort pulsed lasers provide uniquely detailed access to the ultrafast dynamics of physical, chemical, and biological systems, but only a handful of wavelengths are directly produced by solid-state lasers, necessitating efficient high-power frequency conversion. Relativistic plasma mirrors generate broadband power-law spectra, that may span the gap between petawatt-class infrared laser facilities and x-ray free-electron lasers; despite substantial theoretical work the ultimate efficiency of this relativistic high-order-harmonic generation remains unclear. We show that the coherent radiation emitted by plasma mirrors follows a power-law distribution of energy over frequency with an exponent that, even in the ultrarelativistic limit, strongly depends on the ratio of laser intensity to plasma density and exceeds the frequently quoted value of -8/3 over a wide range of parameters. The coherent synchrotron emission model, when adequately corrected for the finite width of emitting electron bunches, is not just valid for p-polarized light and thin foil targets, but generally describes relativistic harmonic generation, including at normal incidence and with finite-gradient plasmas. Our numerical results support the ω-4/3 scaling of the synchrotron emission model as a limiting efficiency of the process under most conditions. The highest frequencies that can be generated with this scaling are usually restricted by the width of the emitting electron bunch rather than the Lorentz factor of the fastest electrons. The theoretical scaling relations developed here suggest, for example, that with a 20-PW 800-nm driving laser, 1 TW/harmonic can be produced for 1-keV photons.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
LeTID-Affected Cells from a Utility-Scale Photovoltaic System Characterized by Deep Level Transient Spectroscopy
Photovoltaic modules from a utility-scale field experienced power loss by light- and elevated temperature-induced degradation (LeTID). Samples of one of the affected monocrystalline silicon cells were cored and extracted from the module packaging and encapsulation. One of the cell fragments was processed using a regeneration cycle of applying short-circuit-rated current in forward bias at 85 degrees C for 2 weeks, while the other fragment was kept in its outdoor-degraded LeTID state. Both samples were scribed to form 2-mm diameter isolated areas using a femtosecond-pulse-width laser micromachining system. Both isolated areas contained front grid line segments which were wire bonded to larger contact pads, and the samples were probed in a cryostat linked to a deep-level transient spectroscopy (DLTS) system. Using DLTS, a majority-carrier, hole-trap defect was detected on each sample with an activation energy of 0.42 eV. The LeTID-degraded sample, however, had a larger signal corresponding to a trap density of 1.1x10^13 cm-3, which was about five times larger than the 2.1x10^12 cm-3 trap density of the regenerated sample.
charge carrier lifetime↗
Pulsed laminar falling films in vertical tubes: Maintaining a continuous liquid film with reduced film thickness
Falling-liquid-film heat transfer is important to a wide variety of industrial applications, including two-phase thermosyphons, falling-film evaporators in the food industry, heat exchangers in fuel-ethanol processing, and the chemical service industry. Particularly for laminar falling films, the heat transfer increases as the film thickness decreases, hence it is desirable to keep the films as thin as possible. This article presents a periodically-pulsed flow concept to reduce the average mass flow inside a vertical tube. The technique provides thinner films than can be achieved with continuous flow. A drainage model is adopted to predict the film thickness as a function of flow rate and location along the tube. The concept is confirmed experimentally by measuring the film thickness in real time in a circular tube using a laser-based absorption technique. A new heat-transfer-based film continuity measurement is also integrated into the optical film measurement setup. Water at ambient temperature and pressure is used for this work. Film thickness reductions of up to 60%, and liquid-film volume-flow reductions of up to 80% compared to the minimum continuous-flow film have been obtained. The time-varying film thickness profile can also be controlled to a limited extent, which may be of interest for process industries.
42 ENGINEERING↗
Amorphous Ag 2-x Cu x S quantum dots: “all-in-one” theranostic nanomedicines for near-infrared fluorescence/photoacoustics dual-modal-imaging-guided photothermal therapy
Integrating dual-modal imaging and photothermal effect within a single nanosystem is an enormous challenge for current nanomedicine application. In this study, non-toxic amorphous Ag 2-x Cu x S quantum dots (QDs) possessing near-infrared fluorescence (NIRF), enhanced photothermal and photoacoustic (PA) performance, as “one-in-all” nanomedicines, are designed and obtained. Cu doping in amorphous Ag 2 S QDs causes red-shift of NIRF to the lowest tissue absorption wavelength in so called “first biowindow” (~820 nm) and improves photothermal conversion efficiency to 44.0% simultaneously. Density functional theory simulation results suggest the fluorescence red-shift and enhanced photothermal/photoacoustics properties can be attributed to the generation of intragap states introduced by Cu doping. The amorphous Ag 2-x Cu x S QDs exhibit high long-term biocompatibility. Under a single laser irradiation with relatively low power density, an effective tumor ablation induced by high photothermal effect of amorphous Ag 2-x Cu x S QDs is achieved in vivo. Simultaneously, the PTT process can be guided by high quality NIRF/PA dual-modal-imaging.
36 MATERIALS SCIENCE↗
Thermal conductivity measurement using modulated photothermal radiometry for nitrate and chloride molten salts
Molten salts are being used or explored for thermal energy storage and conversion systems in concentrating solar power and nuclear power plants. Thermal conductivity of molten salts is an important thermophysical property dictating the performance and cost of these systems, but its accurate measurement has been challenging, as evidenced by wide scattering of existing data in literature. The corrosive and conducting nature of these fluids also leads to time consuming sample preparation processes of many contact-based measurements. Here, in this work, we report the measurement of thermal conductivity of molten salts using a modulated photothermal radiometry (MPR) technique, which is a laser-based, non-contact, frequency-domain method adopted for molten salts for the first time. By unitizing the advantages of front side sensing of frequency-domain measurements and the vertical holder orientation, the technique can minimize the natural convection and salt creeping effects, thus yielding accurate molten salt thermal conductivity . The MPR technique is first calibrated using standard molten materials including paraffin wax and sulfur. It is then applied on measuring pure nitrate salts (NaNO 3 and KNO 3 ), solar salt (NaNO 3 –KNO 3 mixture), and chloride salt (NaCl–KCl–MgCl 2 ). The measurement results are compared with data from literature, especially those obtained from laser flash analysis (LFA). Our results demonstrate that the MPR is a convenient and reliable technique of measuring thermal conductivity of molten salts. Accurate thermal conductivity data of molten salts will be valuable in developing the next-generation high-temperature thermal energy storage and conversion systems.
14 SOLAR ENERGY↗
Compositionally graded aluminum-silicon alloy fabricated via friction extrusion
Herein, a novel solid-phase gradient alloying technique was developed for a high throughput composition-microstructure-mechanical property assessment. Friction extrusion of a two-piece billet setup facilitated the formation of a seamless compositionally graded aluminum (Al)-silicon (Si) extrudate rod, with Si concentration in Al matrix gradually increasing from ~1 at% at one end to ~7 at% at the other end of the rod. We observed a strong dependence of the Al grain size, morphology, and texture on the Si concentration. The Si particles pinned the recrystallized grain boundaries resulting in refined (< 10 µm) and textured grains in the high Si content region, while the Al grains in the low Si region are equiaxed, randomly textured, and with a larger average size (~50 µm). The hardness of Al-Si gradient extrudate increases by ~50% percent with a 6 at% increase in Si content due to Hall Petch and particle strengthening effects. Our approach demonstrates the use of a solid phase processing technique to successfully produce a defect-free continuously compositionally graded bulk components thus overcoming the limitations of porosity and material heterogeneities commonly observed in other techniques such as by additive laser deposition.
36 MATERIALS SCIENCE↗
Dry Printing Pure Copper with High Conductivity and Adhesion for Flexible Electronics
Additive manufacturing of functional devices on various rigid and flexible substrates is rising rapidly due to their design flexibility, rapid manufacturing, and lower cost. Current printing technologies are ink-based and focused on printing silver (Ag) as conductive lines due to its matured ink formulation process, low sintering temperature, ease of printing, and low oxidation rate. However, Ag is the 68th most abundant element on Earth, while copper (Cu) is the 25th, making it much cheaper (>100×) while having a comparable conductivity to Ag. Therefore, printing Cu has become technologically and economically more attractive than Ag. Nevertheless, Cu printing is still a significant challenge in ink-based printing methods due to the higher sintering temperature relative to the glass-transition temperature of most flexible substrates, the higher oxidation rate, the challenging ink formulation process, and ink stability concerns. Here, we demonstrate printing highly conductive Cu on flexible polyimide substrates using a dry printing technique. Cu nanoparticles (~3–30 nm) are generated by on-demand laser ablation of a solid Cu target inside the printer head and under argon background gas. These Cu nanoparticles are then transported through a nozzle and onto the substrate, where they are laser-sintered in real time. The argon gas plays three critical roles in laser plume condensation for nanoparticle generation, transport, and sheath gas to avoid oxidation during sintering. The sintered nanoparticles thus show high electrical conductivity and mechanical stability under static and cyclic tests. Our dry printing technique can potentially revolutionize how electronic devices and sensors are additively manufactured for earth and space applications.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Magnetic field effects on laser energy deposition and filamentation in magneto-inertial fusion relevant plasmas
We report on experimental measurements of how an externally imposed magnetic field affects plasma heating by kJ-class, nanosecond laser pulses. The experiments reported here took place in gas cells analogous to magnetized liner inertial fusion targets. We observed significant changes in laser propagation and energy deposition scale lengths when a 12T external magnetic field was imposed in the gas cell. We find evidence that the axial magnetic field reduces radial electron thermal transport, narrows the width of the heated plasma, and increases the axial plasma length. Reduced thermal conductivity increases radial thermal gradients. This enhances radial hydrodynamic expansion and subsequent thermal self-focusing. Our experiments and supporting 3D simulations in helium demonstrate that magnetization leads to higher thermal gradients, higher peak temperatures, more rapid blast wave development, and beam focusing with an applied field of 12T.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Swift /UVOT follow-up of gravitational wave alerts in the O3 era
ABSTRACT In this paper, we report on the observational performance of the Swift Ultra-violet/Optical Telescope (UVOT) in response to the gravitational wave (GW) alerts announced by the Advanced Laser Interferometer Gravitational Wave Observatory and the Advanced Virgo detector during the O3 period. We provide the observational strategy for follow-up of GW alerts and provide an overview of the processing and analysis of candidate optical/UV sources. For the O3 period, we also provide a statistical overview and report on serendipitous sources discovered by Swift/UVOT. Swift followed 18 GW candidate alerts, with UVOT observing a total of 424 deg2. We found 27 sources that changed in magnitude at the 3σ level compared with archival u- or g-band catalogued values. Swift/UVOT also followed up a further 13 sources reported by other facilities during the O3 period. Using catalogue information, we divided these 40 sources into five initial classifications: 11 candidate active galactic nuclei (AGNs)/quasars, three cataclysmic variables (CVs), nine supernovae, 11 unidentified sources that had archival photometry, and six uncatalogued sources for which no archival photometry was available. We have no strong evidence to identify any of these transients as counterparts to the GW events. The 17 unclassified sources are likely a mix of AGN and a class of fast-evolving transient, and one source may be a CV.
Oates, S. R.↗
Laser-Based Means for Accelerating Nuclear Decay Rate
This project aims to replicate and build upon a reported series of results whereby nuclear decay of unstable species has been accelerated under laser irradiation in the presence of resonantly excited plasmonic nanoparticles. We are currently utilizing a laser system similar to that used within these reports as well as optimizing nanoparticle solution environments in an attempt to replicate reported results or provide alternative pathways that may explain some perceived discrepancies. The current work is being performed with equipment and techniques currently available at SRNL, including nanoparticle synthesis and pulsed lasers for plasmon excitation. The results of these experiments could provide quantitative data that can be used to resolve the discrepancies in the calculations and better estimate the ultimate utility of the process. If verified, this would represent a pathway for using readily available and scalable technology to reduce the long-term radiological storage requirements of certain forms of nuclear waste.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗