Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “jets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Spreading Characteristics and Thrust of Jets from Asymmetric Nozzles

The spreading characteristics of jets from several asymmetric nozzles are studied in comparison to those of an axisymmetric jet, over the Mach number (M(sub J)) range of 0.3 to 1.96. The effect of tabs in two cases, the axisymmetric nozzle fitted with four tabs and a rectangular nozzle fitted with two large tabs, is also included in the comparison. Compared to the axisymmetric jet, the asymmetric jets spread only slightly faster at subsonic conditions, while at supersonic conditions, when screech occurs, they spread much faster. Screech profoundly increases the spreading of all jets. The effect varies in the different stages of screech, and the corresponding unsteady flowfield characteristics are documented via phase-averaged measurement of the fluctuating total pressure. An organization and intensification of the azimuthal vortical structures under the screeching condition is believed to be responsible for the increased spreading. Curiously, the jet from a 'lobed mixer' nozzle spreads much less at supersonic conditions compared to all other cases. This is due to the absence of screech with this nozzle. Jet spreading for the two tab configurations, on the other hand, is significantly more than any of the no-tab cases. This is true in the subsonic regime, as well as in the supersonic regime in spite of the fact that screech is essentially eliminated by the tabs. The dynamics of the streamwise vortex pairs produced by the tabs cause the most efficient jet spreading thus far observed in the study.

Zaman, K. B. M. Q.↗

Jet Evolution Visualized and Quantified Using Filtered Rayleigh Scattering

Filtered Rayleigh scattering was utilized as a flow diagnostic in an investigation of a method for enhancing mixing in supersonic jets. The primary objectives of the study were to visualize the effect of vortex generating tabs on supersonic jets, to exact quantitative data from these planar visualizations, and to detect the presence of secondary flows (i.e., streamwise vorticity) generated by the tabs. An injection seeded frequency-doubled Nd:YAG was the light source and a 14 bit Princeton Instruments iodine charge coupled display (ICCD) camera recorded the image through an iodine cell. The incident wave length of the laser was held constant for each flow case so that the filter absorbed unwanted background light, but permitted part of the thermally broadened Rayleigh scattering light to pas through. The visualizations were performed for axisymmetric jets (D=1.9 cm) operated at perfectly expanded conditions for Mach 1.0, 1.5, and 2.0. All data were recorded for the jet cross section at x/D=3. One hundred instantaneous images were recorded and averaged for each case, with a threshold set to eliminate unavoidable particulate scattering. A key factor in these experiments was that the stagnation air was heated such that the expansion of the flow in the nozzle resulted in the static temperature in the jet being equal to the ambient temperature, assuming isentropic flow. Since the thermodynamic conditions of the flow were approximately the same for each case, increases in the intensity recorded by the ICCD camera could be directly attributed to the Doppler shift, and hence velocity. Visualizations were performed for Mach 1.5 and Mach 2.0 jets with tabs inserted at the nozzle exit. The distortion of the jet was readily apparent and was consistent with Mie scattering-based visualizations. Asymmetry in the intensities of the images indicate the presence of secondary flow patterns which are consistent with the streamwise vortices measured using more traditional diagnostics in subsonic jets with the same tab configurations. Because each tab causes shocks to form, the assumption of isentropic flow is not valid for these cases. However, within a reasonable first-order estimation,the intensity across the illuminated plane for these cases can be related to a value combining density and velocity.

Reeder, Mark F.↗

An Analysis of the Pressures, Forces and Moments Induced by the Ground Vortex Generated by a Single Impinging Jet

When a jet STOVL aircraft is in STOL operation the jets impinge on the ground and generate wall jets flowing radially outward from the points at which the jets impinge. When the forward flowing part of a wall jet meets the free stream flow it is rolled back on itself forming a parabolic shaped ground vortex. Positive pressures are induced on the lower surface of the configuration ahead of the ground vortex and suction pressures are induced over the ground vortex itself. In addition, the suction pressures induced aft of the jet out of ground effect are reduced and lifting pressures are induced on the upper surface. This study analyzes available pressure and force data and develops a method for estimating the forces and moments induced in ground effect. The method includes the effects of configuration variables, height and operating conditions, as well as the effects of the location, deflection and shape of the jet. However, it is limited to single jets at subcritical nozzle pressure ratios. An analysis of the effects of moving over the ground vs. tests over a fixed ground plane is included.

Kuhn, Richard E.↗

Response of High Subsonic Jet to Nonaxisymmetric Disturbances

A model of sound generated in a high subsonic (Mach 0.9) circular jet is solved numerically in cylindrical coordinates for nonaxisymmetric disturbances. The jet is excited by transient mass injection by a finite duration pulse via a modulated ring source. The nonaxisymmetric solution is computed for long times after the initial disturbance has exited the computational domain. The long time behavior of the jet is dominated by vorticity and pressure disturbances generated at the nozzle lip and growing as they convect down-stream in the jet. These disturbances generate sound as they propagate. The primary non-axisymmetric effect that we simulate is that of a flapping mode where regions of high and low pressure alternate on opposite sides of the jet. The predominant feature of this mode is the appearance of relatively large deviations of the pressure from the ambient pressure on opposite sides of the jet and the convection of these regions downstream. We illustrate flow field, near field and far field data. Important nonaxisymmetric characteristics of the near and flow field disturbances include roughly periodic pressure elevations and depressions at opposite values of the azimuthal angle psi. These correspond to pressure disturbances propagating in the axial direction. The azimuthal velocity exhibits a sinusoidal dependence on psi with similar roughly periodic disturbances. For every azimuthal angle psi, the jet radiation peaks about 30 deg. from the jet axis, however there is now a pronounced dependence of the far field radiation pattern on psi.

Bayliss, A.↗

Noise from Supersonic Coaxial Jets: Inverted Velocity Profile - Part 3

The instability wave noise generation model is used to study the instability waves in the two shear layers of an inverted velocity profile, supersonic, coaxial jet and the noise radiated from the dominant wave. The inverted velocity profile jet has a high speed outer stream surrounding a low speed inner stream and the outer shear layer is always larger than the inner shear layer. The jet mean flows are calculated numerically. The operating conditions are chosen to exemplify the effect of the coaxial jet outer shear layer initial spreading rates. Calculations are made for the stability characteristics in the coaxial jet shear layers and the noise radiated from the instability waves for different operating conditions with the same total thrust, mass flow and exit area as a single reference jet. Results for inverted velocity profile jets indicate that relative maximum instability wave amplitudes and far field peak noise levels can be reduced from that of the reference jet by having higher spreading rates for the outer shear layer, low velocity ratios, and outer streams hotter than the inner stream.

Dahl, Milo D.↗

Noise from Supersonic Coaxial Jets: Mean Flow Predictions - Part 1

Recent theories for supersonic jet noise have used an instability wave noise generation model to predict radiated noise. This model requires a known mean flow that has typically been described by simple analytic functions for single jet mean flows. The mean flow of supersonic coaxial jets is not described easily in terms of analytic functions. To provide these profiles at all axial locations, a numerical scheme is developed to calculate the mean flow properties of a coaxial jet. The Reynolds-averaged, compressible, parabolic boundary layer equations are solved using a mixing length turbulence model. Empirical correlations are developed to account for the effects of velocity and temperature ratios and Mach number on the shear layer spreading. Both normal velocity profile and inverted velocity profile coaxial jets are considered. The mixing length model is modified in each case to obtain reasonable results when the two stream jet merges into a single fully developed jet. The mean flow calculations show both good qualitative and quantitative agreement with measurements in single and coaxial jet flows.

Dahl, Milo D.↗

The Effects of Crossflow on the Pressures and Lift Induced by the Fountain Generated Between Two Impinging Jets

When a jet STOVL aircraft is hovering, or in a crossflow, while close to the ground wall jets flowing radially outward from the impingement points of the jets are generated. An upflow, or fountain, is generated where the wall jets from adjacent jets meet on the ground surface. The induced lift and suckdown generated by the impingement of the fountain on the lower surface of the configuration has been the subject of previous studies. This study analyzes the limited available pressure and force data on the effect of crossflow on the fountain induced lift and suckdown. The analysis includes the effects of jet spacing, height and operating conditions. However, it is limited to twin jet configurations of circular, vertical jets operating at subcritical nozzle pressure ratios over a fixed ground surface.

Kuhn, Richard E.↗

Analysis and Modeling of a Two-Phase Jet Pump of a Flow Boiling Test Facility for Aerospace Applications

Jet pumps are devices capable of pumping fluids to a higher pressure employing a nozzle/diffuser/mixing chamber combination. A primary fluid is usually allowed to pass through a converging-diverging nozzle where it can accelerate to supersonic speeds at the nozzle exit. The relatively high kinetic energy that the primary fluid possesses at the nozzle exit is accompanied by a low pressure region in order to satisfy Bernoulli's equation. The low pressure region downstream of the nozzle exit permits a secondary fluid to be entrained into and mixed with the primary fluid in a mixing chamber located downstream of the nozzle. Several combinations may exist in terms of the nature of the primary and secondary fluids in so far as whether they are single or two-phase fluids. Depending on this, the jet pump may be classified as gas/gas, gas/liquid, liquid/liquid, two-phase/liquid, or similar combinations. The mixing chamber serves to create a homogeneous single-phase or two-phase mixture which enters a diffuser where the high kinetic energy of the fluid is converted into pressure energy. If the fluid mixture entering the diffuser is in the supersonic flow regime, a normal shock wave usually develops inside the diffuser. If the fluid mixture is one that can easily change phase, a condensation shock would normally develop. Because of the overall rise in pressure in the diffuser as well as the additional rise in pressure across the shock layer, condensation becomes more likely. Associated with the pressure rise across the shock is a velocity reduction from the supersonic to the subsonic range. If the two-phase flow entering the diffuser is predominantly gaseous with liquid droplets suspended in it, it will transform into a predominantly liquid flow containing gaseous bubbles (bubbly flow) somewhere in the diffuser. While past researchers have been able to model the two-phase flow jet pump using the one-dimensional assumption with no shock waves and no phase change, there is no research known to the authors apart from that of Anand (1992) which accounted for condensation shocks. One of the objectives of this research effort is to develop a comprehensive model in which the effects of phase slip and inter-phase heat transfer as well as the wall friction and shock waves are accounted for. While this modeling effort is predominantly analytical in nature and is primarily intended to provide a parametric understanding of the jet pump performance under different operating scenarios, another parallel effort employing a commercial CFD code is also implemented. The latter effort is primarily intended to model an axisymmetric counterpart of the problem in question. The viability of using the CFD code to model a two-phase flow jet pump will be assessed by attempting to recreate some of the existing performance data of similar jet pumps. The code will eventually be used to generate the jet pump performance characteristics of several scenarios involving jet pump geometries as well as flow regimes in order to be able to determine an optimum design which would be suitable for a two-phase flow boiling test facility at NASA-Marshall. Because of the extensive nature of the analytical model developed, the following section will only provide very brief highlights of it, while leaving the details to a more complete report submitted to the NASA colleague. This report will also contain some of the simulation results obtained using the CFD code.

Sherif, S. A.↗

Investigation of Interference of a Deflected Jet with Free Stream and Ground on Aerodynamic Characteristics of a Semispan Delta-Wing VTOL Model

An investigation of the mutual interference effects of the ground, wing, deflected jet stream, and free stream of a semispan delta-wing VTOL model at zero and low forward speeds has been conducted in the 17-foot test section of the Langley 300-MPH 7-by 10-foot tunnel. The model consisted of two interchangeable semispan clipped delta wings, a simplified fuselage, and a high-pressure jet for simulation of a jet exhaust. Attached to the wing behind the jet were various sets of vanes for deflecting the jet stream to different turning angles. The effect of ground proximity gave the normally expected losses in lift at zero and very low forward speeds (up to about 60 or 80 knots for the assumed wing loading of 100 lb/sq ft); at higher forward speeds ground effects were favorable. At low forward speeds, out of ground effect, the model encountered large losses in lift and large nose-up pitching moments with the model at low angles of attack and the jet deflected 90 deg or 75 deg (the angles required for VTOL performance and very low forward speeds). Rotating the model to higher angles of attack and deflecting the jet back to lower angles eliminated these losses in lift. Moving the jet rearward with respect to the wing reduced the losses in lift and the nose-up moments at all speeds within the range of this investigation.

Spreemann, Kenneth P.↗

Static Investigation of Paddle Vane Oscillating in Jet of 1,300-Pound-Thrust Rocket Motor

The results of a static investigation conducted to measure the normal forces on the entire jet-vane assembly and the hinge moments on the jet vane produced by a paddle vane oscillating in the jet of a 1,500-pound-thrust rocket motor are presented for vane-deflection angles from -5 deg to 25 deg. A maximum average normal force of 71 pounds with a corresponding value for maximum average hinge moment of 228 inch-pounds was obtained with the maximum area of jet vane immersed at a jet-vane angle of 25 deg decrease in thrust caused by immersion of the jet vane varied from a maximum loss of about 58 pounds, or approximately 5 percent at maximum jet-vane angle of 25 deg, to zero loss at jet-vane angles less than approximately 10 deg.

Lanford, Wade E.↗

Tone Noise and Nearfield Pressure Produced by Jet-Cavity Interaction

Cavity flow resonance can cause numerous problems in aerospace applications. While our long-term goal is to understand cavity flows well enough to devise effective cavity resonance suppression techniques, this paper describes a fundamental study of resonant tones produced by jet-cavity interaction at subsonic and supersonic speeds. Our specific jet-cavity configuration can also be used as a test bed for evaluating active and passive flow resonance control concepts. Two significant findings emerge from this study. 1) Originally, we expected that tones produced by jet-cavity interaction would resemble cavity tones or jet tones or would involve some simple combinations of each. The experimental data do not support these expectations: instead, the jet cavity interaction produce a unique set of tones. We propose simple yet and physically insightful correlations for these tones. Although the pressure patterns on the cavity floor display very complex variations with the Mach number for a length/depth = 8 cavity, the tones correspond to the acoustic modes of the cavity-independent of flow. For a length/ depth = 3 cavity, however, a surprise emerges: the pressure patterns on the cavity floor are not so complex but the tones depend significantly on the flow. Additionally, we examine the role of external feedback unique to jet-cavity interaction. 2) Previous research led us to expect that traditional classifications (open, transitional, or closed) for cavities in an infinite flight stream would be insensitive to small changes in Mach number and would depend primarily on cavity length/depth ratios. Use of the novel high resolution photoluminescent pressure sensitive paint shows that the classifications are actually quite sensitive to jet Mach number for a length/depth = 8 cavity. However, these classifications provide no guidance whatsoever for tone amplitude or frequency. Detailed experimental data and insights presented here will assist researchers who are performing numerical simulations of jet-cavity flows as a first step toward devising resonance suppression methods.

Raman, Ganesh↗

Modeling of a Two-Phase Jet Pump with Phase Change, Shocks and Temperature-Dependent Properties

One of the primary motivations behind this work is the attempt to understand the physics of a two-phase jet pump which constitutes part of a flow boiling test facility at NASA-Marshall. The flow boiling apparatus is intended to provide data necessary to design highly efficient two-phase thermal control systems for aerospace applications. The facility will also be capable of testing alternative refrigerants and evaluate their performance using various heat exchangers with enhanced surfaces. The test facility is also intended for use in evaluating single-phase performance of systems currently using CFC refrigerants. Literature dealing with jet pumps is abundant and covers a very wide array of application areas. Example application areas include vacuum pumps which are used in the food industry, power station work, and the chemical industry; ejector systems which have applications in the aircraft industry as cabin ventilators and for purposes of jet thrust augmentation; jet pumps which are used in the oil industry for oil well pumping; and steam-jet ejector refrigeration, to just name a few. Examples of work relevant to this investigation includes those of Fairuzov and Bredikhin (1995). While past researchers have been able to model the two-phase flow jet pump using the one-dimensional assumption with no shock waves and no phase change, there is no research known to the author apart from that of Anand (1992) who was able to account for condensation shocks. Thus, one of the objectives of this work is to model the dynamics of fluid interaction between a two-phase primary fluid and a subcooled liquid secondary fluid which is being injected employing atomizing spray injectors. The model developed accounts for phase transformations due to expansion, compression, and mixing. It also accounts for shock waves developing in the different parts of the jet pump as well as temperature and pressure dependencies of the fluid properties for both the primary two-phase mixture and the secondary subcooled liquid. The research effort on which this document partly reports described a relatively simple model capable of describing the performance of a two-phase flow jet pump. The model is based on the isentropic homogeneous expansion/compression hypothesis and is capable of fully incorporating the effects of shocks in both the mixing chamber and the throat/diffuser parts of the pump. The physical system chosen is identical to that experimentally tested by Fairuzov and Bredikhin (1995) and should therefore be relatively easy to validate.

Sherif, S. A.↗

The Applicability of Jet-Shear-Layer Mixing and Effervescent Atomization for Low-NO(x) Combustors

An investigation has been conducted to develop appropriate technologies for a low-NO(x), liquid-fueled combustor. The combustor incorporates an effervescent atomizer used to inject fuel into a premixing duct. Only a fraction of the combustion air is used in the premixing process. This fuel-rich mixture is introduced into the remaining combustion air by a rapid jet-shear-layer mixing process involving radial fuel-air jets impinging on axial air jets in the primary combustion zone. Computational modeling was used as a tool to facilitate a parametric analysis appropriate to the design of an optimum low-NO(x) combustor. A number of combustor configurations were studied to assess the key combustor technologies and to validate the three-dimensional modeling code. The results from the experimental testing and computational analysis indicate a low-NO(x) potential for the jet-shear-layer combustor. Key features found to affect NOx emissions are the primary combustion zone fuel-air ratio, the number of axial and radial jets, the aspect ratio and radial location of the axial air jets, and the radial jet inlet hole diameter. Each of these key parameters exhibits a low-NO(x) point from which an optimized combustor was developed Also demonstrated was the feasibility of utilizing an effervescent atomizer for combustor application. Further developments in the jet-shear-layer mixing scheme and effervescent atomizer design promise even lower NO(x) with high combustion efficiency.

Colantonio, R. O.↗

On the Anticorrelation Between High Accretion Luminosity and Radio Jet Ejection in Gro J1655-40 and Other Objects

A model is described in which radio jet formation in accreting objects is suppressed by processes which occur when the accretion rate approaches the Eddington limit. This was motivated by GRO J1655-40 and other objects which show an anticorrelation between high luminosity and the onset of a radio jet. The jet production mechanism employed is the Blandford-Payne MHD acceleration process, seeded by an e'e- pair wind. Observations indicate that all key ingredients of this mechanism are, or should be, present in these sources. Observed jet velocities and total powers are consistent with theoretical and numerical predictions of this model. The primary jet suppression mechanism proposed is the Papaloizou-Pringle compressible shear instability, which should disrupt the jet-producing region of the disk when the accretion rate approaches about one-third Eddington. The turn-on of the jet in GRO J 1 655 - 40 is consistent with this estimate. When super-Eddington, the disk should also drive an optically thick, subrelativistic wind, which may be a secondary jet suppression mechanism. The possible presence of such a wind is seen in the early spectral evolution of GRO J1655-40 and in the broad absorption lines of certain quasi-stellar objects (QSOs). Important tests of the model would be independent measurements of the compact object masses in these sources, a comparison of normal and broad absorption line (BAL) QSO X-ray spectra to see if the latter objects are significantly cooler, and a low-frequency search around BAL QSOs to see if at least some have fossil radio sources.

Meier, D.↗

Can Kelvin-Helmholtz Instabilities of Jet-Like Structures and Plumes Cause Solar Wind Fluctuations at 1AU

During its south polar passage in 1994, Ulysses sampled the solar wind emerging from the south polar coronal hole. In analysing these data two types of density fluctuations lasting a few hours have been reported, one characterized by fluctuations in velocity gradients ("microstreams") and the other by magnetic plus thermal-pressure balance structures ("PBS"). Microstreams were both temporal and spatial in nature. At higher frequencies, MHD turbulence was observed and found to be less evolved than in the ecliptic, but essentially independent of heliographic latitude. It is argued here that microstreams, PBS, and MHD turbulence could all be the remnant of shears associated with plumes and other filamentary structures ("jets") which have been reported to exist in coronal holes. The shear between a jet and its ambient can become unstable to the MHD Kelvin-Helmholtz ("KH') instability at 5-10 solar radius and the propagating instability can cause fluctuations like those seen by Ulysses. This motivates us to simulate coronal jets using a 3D MHD ZEUS code. The first 2D results have just started to come and are promising. To study the KH instability the jet is perturbed at the boundary with a linear amplitude and fixed frequency. The jet seems to pass through various distinct phases, one of which Is apparently dominated by KH instabilities. These instabilities drive oblique shocks into the jet as the turbulent eddies contact the jet surface. It is known that KH instabilities and internal shock waves are partially suppressed by magnetic field tension. Hence, in simulating far along the jet the Instability is expected to produce Alfvenic fluctuations like those seen near 1 AU.

Parhi, Shyamsundar↗

Analysis of the PKS0637-752 X-Ray Jet System

The X-ray jet emitted from the quasar PKS0637-752 is the largest and most luminous detected to date. It extends 10 arcsec west of the nucleus, and is coincident with GHz radio jet emission in this region. If the individual X-ray/optical/radio knots in this jet were detected as isolated objects, they might be classified as BL Lac objects or quasars. We present a detailed analysis of the Chandra observations of this system, including a search for an intra-cluster medium to confine the jet, and limits to X-ray emission from the eastern radio knot and past the bend of the radio jet to the northwest. The projection in the plane of the sky implies that the X-ray jet is an aligned extension of the pc-scale jet, for which VLBI/VSOP observations show super-luminal motion with an apparent velocity of 11c. In this case, the X-ray jet is of order 1 Mpc in length, and explaining the X-ray emission mechanism presents new challenges.

Schwartz, D. A.↗

Multiple Mode Actuation of a Turbulent Jet

The effects of multiple mode periodic excitation on the evolution of a circular turbulent jet were studied experimentally. A short, wide-angle diffuser was attached to the jet exit. Streamwise and cross-stream excitations were introduced at the junction between the jet exit and the diffuser inlet on opposing sides of the jet. The introduction of high amplitude, periodic excitation in the streamwise direction enhances the mixing and promotes attachment of the jet shear-layer to the diffuser wall. Cross-stream excitation applied over a fraction of the jet circumference can deflect the jet away from the excitation slot. The two modes of excitation were combined using identical frequencies and varying the relative phase between the two actuators in search of an optimal response. It is shown that, for low and moderate periodic momentum input levels, the jet deflection angles depend strongly on the relative phase between the two actuators. Optimum performance is achieved when the phase difference is pi +/- pi/6. The lower effectiveness of the equal phase excitation is attributed to the generation of an azimuthally symmetric mode that does not produce the required non-axisymmetric vectoring. For high excitation levels, identical phase becomes more effective, while phase sensitivity decreases. An important finding was that with proper phase tuning, two unsteady actuators can be combined to obtain a non-linear response greater than the superposition of the individual effects.

Pack, LaTunia G.↗

Multiple Mode Actuation of a Turbulent Jet

The effects of multiple mode periodic excitation on the evolution of a circular turbulent jet were studied experimentally. A short, wide-angle diffuser was attached to the jet exit. Streamwise and cross-stream excitations were introduced at the junction between the jet exit and the diffuser inlet on opposing sides of the jet. The introduction of high amplitude, periodic excitation in the streamwise direction enhances the mixing and promotes attachment of the jet shear-layer to the diffuser wall. Cross-stream excitation applied over a fraction of the jet circumference can deflect the jet away from the excitation slot. The two modes of excitation were combined using identical frequencies and varying the relative phase between the two actuators in search of an optimal response. It is shown that, for low and moderate periodic momentum input levels, the jet deflection angles depend strongly on the relative phase between the two actuators. Optimum performance is achieved when the phase difference is pi +/- pi/6. The lower effectiveness of the equal phase excitation is attributed to the generation of an azimuthally symmetric mode that does not produce the required non-axisymmetric vectoring. For high excitation levels, identical phase becomes more effective, while phase sensitivity decreases. An important finding was that with proper phase tuning, two unsteady actuators can be combined to obtain a non-linear response greater than the superposition of the individual effects.

Pack, LaTunia G.↗