SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Experimental results are reported for torsional fatigue specimens of high-strength steel 4370 and tensile bars of mild steel A-106 which present evidence of a hydrogen-induced strain-aided hardening effect. These results are consistent with the postulate that hydrogen suppresses ductile processes required for crack initiation at large plastic strains.
The 1.24-sec pulsations of Her X-1 in the energy range 13-75 keV have been analyzed in data obtained from the UCSD/MIT experiment on HEAO 1 during observations of the source on three dates in February 1978 and three in August 1978. Observational results are (1) the main pulse broadens somewhat with increasing energy; (2) the pulsation light curve undergoes pronounced changes at the leading edge of the main pulse from day to day; (3) spectral hardening within the main pulse is confirmed; (4) a 40-60 keV spectral feature in the spectrum is confirmed; (5) this feature is resolved, the pulse width broadening is greater than 20%, and its centroid varies with pulsation phase; and (6) the 13-75 keV spectrum does not noticeably vary from day to day, except for an overall intensity factor. Some implications of these results for the prevailing models of Her X-1 and the HZ Her-Her X-1 system are briefly discussed.
A series of Copernicus, Ariel V and optical observations of the X-ray burst source 4U 1735 - 44 (= MXB 1735 - 44) revealed properties very similar to those of the 'Sco X-1 like' sources. During one run, the non-burst X-ray flux varied by a factor of 2 on a time-scale of hours and this was associated with a general hardening of the spectrum. The source was relatively constant throughout the remaining observations. An Ariel V spectrum obtained during a quiescent interval deviated from a simple thermal model in that it showed both a high energy deficiency and a low energy excess. Near simultaneous spectroscopy of the optical counterpart confirmed the general features reported by McClintock et al. Spectra taken on successive nights revealed the H-beta emission to be variable.
The conference covered the radiation effects on devices, circuits, and systems, physics and basic radiation effects in materials, dosimetry and radiation transport, spacecraft charging, and space radiation effects. Other subjects included single particle upset phenomena, systems-generated electromagnetic pulse phenomena, fabrication of hardened components, testing techniques, and hardness assurance.
The effects of both mechanical surface treatments and heat treatments on the erosion resistance of 6061 aluminum alloy were studied in order to gain a better understanding of material properties which affect erosion behavior. It was found that mechanical surface treatments have little or no effect on the erosion resistance. This is due to the formation by particle impact of a work-hardened surface layer, independent of the initial surface condition. The erosion resistance of aluminum single crystals was found to be independent of orientation, which is due to destruction of the surface microstructure and formation of a polycrystalline surface layer by the particle impact as observed by X-ray diffraction. Although on solution treatment of annealed aluminum 6061 the increase in hardness is accompanied by an increase in erosion resistance, precipitation treatment (which causes a further increase in hardness) results in a slightly lower erosion resistance.
The use of a broadband backscatter technique to obtain the frequency dependence of the longitudinal-wave ultrasonic backscatter coefficient from a collection of scatterers in a solid is investigated. Measurements of the backscatter coefficient were obtained over the range of ultrasonic wave vector magnitude-glass sphere radius product between 0.1 and 3.0 from model systems consisting of dilute suspensions of randomly distributed crown glass spheres in hardened polyester resin. The results of these measurements were in good agreement with theoretical prediction. Consequently, broadband measurements of the ultrasonic backscatter coefficient may represent a useful approach toward characterizing the physical properties of scatterers in intrinsically inhomogeneous materials such as composites, metals, and ceramics, and may represent an approach toward nondestructive evaluation of these materials.
Gamma-ray continuum emission from 0.3 to 1 MeV was observed with the gamma-ray spectrometer on the Solar Maximum Mission satellite during two impulsive solar flares on 1980 March 29, from active region 2363 at 0918 UT and from active region 2357 at 0955 UT. Evidence is presented for a hardening of the spectrum during the impulsive phase of the flares. The photon intensity greater than 100 keV appears to decay at a slower rate than that at lower energies. Time-integrated photon spectra for both flares are incompatible with a single-temperature thermal-bremsstrahlung model. Upper limits for prompt and delayed gamma-ray lines are presented.
A pendulum-type test device has been built for use in studying rubs between a turbine or compressor blade tip or labyrinth seal knife edge and specimens of abradable gas path seal materials. The device allows measurement of the rub energy dissipated in a single wear event, along with friction and normal forces and wear. Subsequent rubs over the same surface can also be monitored, with microscopic observation of the rub surface being possible after any of the passes. The device was used in tests of several potential abradable materials, ranging from porous to fully dense. It was shown that the rub energy dissipated in initial and subsequent passes is a fundamental parameter in the evaluation of material abradability. Rub energy was found to be influenced by such factors as: density and tensile (or yield) strength of the abradable material, prior densification or work hardening of the rub surface, and the sharpness of the leading edge of the blade tip.
The X-ray spectra of the Crab pulsar and Crab Nebula are analyzed. Observations were made with OSO 8 on March 17-18, 1978, with all spacecraft telemetry assigned to one detector during seven dwell mode experiments. A resolution of 1.25 ms was obtained for pulse-height-analyzed counts in 64 channels. Progressive hardening and subsequent softening of the spectrum across the pulse was found. The fraction of the pulsed flux, exhibiting a spectral variability of about 0.14 was concentrated solely in the region between the two peaks. A model is suggested in which the pulsed X-ray emission from the Crab pulsar consists of two components: one is physically related to the double-peaked gamma-ray pulse and possibly to radio and optical pulses, but has no spectral dependence on the pulse phase, while the other exhibits spectral variability with the pulse phase but is confined to the interpeak emission seen with X-ray energies.
The transfer of X-rays through a hot, magnetized, scattering atmosphere is studied using a Monte Carlo technique. The process considered is Compton scattering, including cyclotron resonance scattering. Unlike previous work on the subject, the effects of frequency shifts, relativistic corrections, recoil, and polarization mode changes have been included. It is found that the emergent X-ray spectra harden toward the magnetic equator, are cut off at a frequency less than the fundamental cyclotron frequency, and depend on the magnetic field strength. The relevance of the results to observed pulsar spectra is indicated.
MA 6000E is a corrosion resistant, gamma-prime strengthened ODS alloy under development for advanced turbine blade applications. The high temperature, 1093 C, rupture strength is superior to conventional nickel-base alloys. This paper addresses the fatigue behavior of the alloy. Excellent properties are exhibited in low and high cycle fatigue and also thermal fatigue. This is attributed to a unique combination of microstructural features, i.e., a fine distribution of dispersed oxides and other nonmetallics, and the highly elongated grain structure which advantageously modify the deformation characteristics and crack initiation and propagation modes from that characteristic of conventional gamma-prime hardened superalloys.
Progress made in the industrial processing of preimpregnated composites with unidirectional fibers is discussed, with particular emphasis on applications within the aerospace industry. Selection of industrial materials is considered. Attention is given to the conditions justifying the use of composites and the properties required of industrial prepregs. The hardening cycle is examined for the cases of nonmodified and polymer modified resins, with attention given to the stabilization of flow, the necessary changes of state, viscosity control, and the elimination of porosity. The tooling necessary for the fabrication of a laminated plate is illustrated, and the influence of fabrication and prepreg properties on the mechanical characteristics of a laminate are indicated. Finally, the types of prepregs available and the processing procedures necessary for them are summarized.
The angular distribution of electrons and ions at times of spacecraft charging were examined for several charging events. Generally it was found that electrons measured perpendicular to the Earth's magnetic field are more intense and more energetic than those measured parallel to the magnetic field during charging events. During the substorm charging injection, the electron spectra harden at all angles to the magnetic field as the evolution of the charging spectra is monitored by the P78-2 satellites. An example of the onset of charging and the changes in the electron distributions is examined. The evolution of the electrons from a 'soft' plasma sheet distribution to a 'hard' charging distribution is compared with the charging of Kapton on the satellite and the spacecraft frame potential. The ions are used to determine the spacecraft potential. Evidence of periodic surface potential variations related to particle anisotropies are presented and discussed.
The feasibility of building and operating a grazing incidence X-ray telescope for auroral zone studies from the Polar Plasma Laboratory (PPL) is discussed. A detailed structural analysis of the preferred design, an array of seven nested Wolter mirrors, is presented. An engineering evaluation of the requirements for the instrumental configuration, power, weight and telemetry is included. The problems of radiation hardening and thermal control are discussed. The resulting strawman instrument is presented.
Diamond sheet is termed a diamond tool material because it is not a cutting tool, but rather a new material from which a variety of different tools may be fabricated. In appearance and properties, it resembles a sheet of copper alloy with diamond abrasive dispersed throughout it. It is capable of being cut, formed, and joined by conventional methods, and subsequently used for cutting as a metal bonded diamond tool. Diamond sheet is normally made with industrial diamond as the abrasive material. The metal matrix in diamond sheet is a medium hard copper alloy which has performed well in most applications. This alloy has the capability of being made harder or softer if specific cutting conditions require it. Other alloys have also been used including a precipitation hardened aluminum alloy with very free cutting characteristics. The material is suitable for use in a variety of cutting, surfacing, and ring type tools, as well as in such mundane items as files and sandpaper. It can also be used as a bearing surface (diamond to diamond) and in wear resistant surfaces.
Boron/aluminum can develop significant internal matrix cracking when fatigued. These matrix cracks can result in a 40 percent secant modulus loss in some laminates, even when fatigued below the fatigue limit. It is shown that the same amount of fatigue damage will develop during stress or strain-controlled tests. Stacking sequence has little influence on secant modulus loss. The secant modulus loss in unidirectional composites is small, whereas the losses are substantial in laminates containing off-axis plies. A simple analysis is presented that predicts unnotched laminate secant modulus loss due to fatigue. The analysis is based upon the elastic modulus and Poisson's ratio of the fiber and matrix, fiber volume fraction, fiber orientations, and the cyclic-hardened yield stress of the matrix material. Excellent agreement was achieved between model predictions and experimental results. With this model, designers can project the material stiffness loss for design load or strain levels and assess the feasibility of its use in stiffness-critical parts.
Three dimensional, nonlinear finite element structural analyses were performed for a simulated combustor liner specimen to assess the capability of nonlinear analyses using classical inelastic material models to represent the thermoplastic creep response of the one half scale component. Results indicate continued cyclic hardening and ratcheting while experimental data suggested a stable stress strain response after only a few loading cycles. The computed stress strain history at the critical location was put into two life prediction methods, strainrange partitioning and a Pratt and Whitney combustor life prediction method to evaluate their ability to predict cyclic crack initiation. It is found that the life prediction analyses over predicted the observed cyclic crack initiation life.
The influence of inelastic material models on computed stress-strain states, and therefore predicted lives, was studied for thermomechanically loaded structures. Nonlinear structural analyses were performed on a fatigue specimen which had been subjected to thermal cycling in fluidized beds and on a mechanically load cycled benchmark notch specimen. Four incremental plasticity creep models (isotropic, kinematic, combined isotropic kinematic, combined plus transient creep) were exercised using the MARC program. Of the plasticity models, kinematic hardening gave results most consistent with experimental observations. Life predictions using the computed strain histories at the critical location with a strainrange partitioning approach considerably overpredicted the crack initiation life of the thermal fatigue specimen.