Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “graphitization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Evaluation of Composite Honeycomb Sandwich Panels Under Compressive Loads at Elevated Temperatures

Fourteen composite honeycomb sandwich panels were tested to failure under compressive loading. The test specimens included panels with both 8 and 24-ply graphite-bismaleimide composite facesheets and both titanium and graphite-polyimide core materials. The panels were designed to have the load introduced through fasteners attached to pairs of steel angles on the ends of the panels to simulate double shear splice joints. The unloaded edges were unconstrained. Test temperatures included room temperature, 250F, and 300F. For the room and 250F temperature tests, the 24-ply specimen failure strains were close to the unnotched allowable strain values and failure loads were well above the design loads. However, failure strains much lower than the unnotched allowable strain values, and failure loads below the design loads were observed with several of the 8-ply specimens. For each individual test temperature, large variations in the failure strains and loads were observed for the 8-ply specimens. Dramatic decreases in the failure strains and loads were observed for the 24-ply specimens as the test temperature was increased from 250F to 300F. All 8-ply specimens appeared to have failed in a facesheet strength failure mode for all test temperatures. The 24-ply specimens displayed appreciably greater amounts of bending prior to failure than the 8-ply specimens, and panel buckling occurred prior to facesheet strength failure for the 24-ply room and 250F temperature tests.

Walker, Sandra P.↗
NASA NTRS1999

Utilization of Induction Bonding for Automated Fabrication of TIGR

A laboratory study of magnetic induction heat bonding of titanium foil and graphite fiber reinforced polymer prepreg tape, TiGr, demonstrated that the process is a viable candidate for low cost fabrication of aircraft structure made of this new material form. Data were obtained on weld bonding of PIXA and PETI-5 prepreg to titanium. Both the foil and honeycomb forms of titanium were investigated. The process relies on magnetic susceptor heating of titanium, not on high frequency heating of graphite fiber. The experiments showed that with a toroid magnet configuration, good weld bonds might be obtained with heating times of a few seconds. These results suggest the potential is good for the induction heating process to achieve acceptable commercial production rates.

Hinkley, Jeffrey A.↗
NASA NTRS1999

Macrosegregation of GeSi Alloys Grown in a Static Magnetic Field

Axial and radial macrosegregation profiles have been determined for GeSi alloy crystals grown by the vertical Bridgman technique. An axial 5 Tesla magnetic field was applied to several samples during growth to decrease the melt velocities by means of the Lorentz force. Compositions were measured with either energy dispersive X-ray spectroscopy (EDS) on a scanning electron microscope (SEM) or by wavelength dispersive X-ray spectroscopy (WDS) on a microprobe. The crystals were processed in graphite, hot-pressed boron nitride (BN), and pyrolytic boron nitride (PBN) ampoules, which produced various solid-liquid interface shapes during solidification. Those samples grown in a graphite ampoule exhibited radial profiles consistent with a highly concave interface and axial profiles indicative of complete mixing in the melt. The samples grown in BN and PBN ampoules had less radial variation. Axial macrosegregation profiles of these samples fell between the predictions for a completely mixed melt and one where solute transport is dominated by diffusion. Possible explanations for the apparent insufficiency of the magnetic field to achieve diffusion controlled growth conditions are discussed.

Ritter, T. M.↗
NASA NTRS1999

Influence of Applied Thermal Gradients and a Static Magnetic Field on Bridgman-Grown GeSi Alloys

The effect of applied axial and radial thermal gradients and an axial static magnetic field on the macrosegregation profiles of Bridgman-grown GeSi alloy crystals has been assessed. The axial thermal gradients were adjusted by changing the control setpoints of a seven-zone vertical Bridgman furnace. The radial thermal gradients were affected by growing samples in ampoules with different thermal conductivities, namely graphite, hot-pressed boron nitride (BN), and pyrolytic boron nitride (PBN). Those samples grown in a graphite ampoule exhibited radial profiles consistent with a highly concave interface and axial profiles indicative of complete mixing in the melt. The samples grown in BN and PBN ampoules had less radial variation. Axial macrosegregation profiles of these samples fell between the predictions for a completely mixed melt and one where solute transport is dominated by diffusion. All of the samples were grown on Ge seeds. This resulted in a period of free growth until the Si concentration in the solid was in equilibrium with the Si concentration in the liquid. The length of crystal grown during this period was inversely proportional to the applied axial thermal gradient. Several samples were grown in an axial 5 Tesla magnetic field. Measured macroscopic segregation profiles on these samples indicate that the magnetic field did not, in general, reduce the melt flow velocities to below the growth velocities.

Volz, M. P.↗
NASA NTRS1998

Bridgman Growth of GeSi Alloys in a Static Magnetic Field

Ge(0.95)Si(0.050 alloy crystals have been grown by the vertical Bridgman technique, both with and without an axial 5 Tesla magnetic field. The crystals were processed in a constant axial thermal gradient and the effects of graphite, hot pressed boron nitride, and pyrolitic boron nitride ampoule materials on interface shapes and macrosegregation profiles were investigated. The sample grown in a graphite ampoule at 5 Tesla exhibited a macroscopic axial concentration profile close to that of complete mixing and strong striation patterns. In samples grown in boron nitride ampoules, both with and without a 5 Tesla magnetic field applied, measured macroscopic axial concentration profiles were intermediate between those expected for a completely mixed melt and diffusion-controlled growth, and striation patterns were also observed. Possible explanations for the apparent inability of the magnetic field to reduce the flow velocities to below the growth velocities are discussed, and results of growth experiments in pyrolitic boron nitride ampoules are also described.

Volz, M. P.↗
NASA NTRS1997

New Potential Sources for Black Onaping Carbon

One intriguing and important issue of the Sudbury Structure concerns the source of the relatively large amount of C in the Onaping Formation Black member. This dilemma was recently addressed, and the conclusion was reached that an impactor could not have delivered all of the requisite C. Becker et al. have suggested that much of the C came from the impactor and reported the presence of interstellar He "caged" inside some fullerenes that may have survived the impact. So, conceivably, the C inventory in the Sudbury Structure comes from both target and impactor materials, although the known target rocks have little C. We discuss here the possibility of two terrestrial sources for at least some of the C: (1) impact evaporation/dissociation of C from carbonate target rocks and (2) the presence of heretofore-unrecognized C-rich (up to 26 wt%) siliceous "shale," fragments, which are found in the upper, reworked Black member. Experimental: Hypervelocity impact of a 0.635-diameter Al projectile into dolomite at 5.03 km/s (performed at the Ames Research Center vertical gun range) produced a thin, black layer (= 0.05 mm thick) that partially lined the crater and coated impactor remnants. Scanning electronic microscope (SEM) imagery shows this layer to be spongelike on a submicron scale and Auger spectroscopic analyses yield: 33% C, 22% Mg, 19% 0, and 9% Al (from the projectile). Elemental mapping shows that all of the available 0 is combined with Ca and Mg, Al is not oxidized, and C is in elemental form. Dissociation efficiency of C from CO2 is estimated to be <10% of crater volume. Raman spectroscopy indicates that the C is highly disorganized graphite. Another impact experiment [4] also produced highly disordered graphite from a limestone target (reducing collector), in addition to small amounts of diamond/lonsdaleite/chaoite (oxidizing collector). These experiments confirm the reduction of C from carbonates in impact vapor plumes. Observational: SEM observations and microprobe analyses of small, black shalelike inclusions in the upper Black Onaping indicate high C contents (7-26 wt% avg. = 16%). They contain mostly quartz and carbonaceous matter with small amounts of altered K-feldspar, clays, Fe oxide, and a sulfide. No evidence of shock is seen in quartz, and overall characteristics indicate a natural, lightly metamorphosed carbonaceous shale or mudstone that probably existed as a preimpact rock in the target region and distal fragments washed in during early crater filling. Fragments range in size from tens of microns to cm and increase in abundance in the upper Black toward the Onwatin contact, although their distribution is highly irregular. This increase corresponds to an increase in "organic" C with increasingly negative delta-13 C values and S, together with a decrease in fullerene abundance. In addition, we have found soot in acid-demineralized residues of the Onwatin but not in the Onaping samples. These data could be consistent with impact plume and atmospheric chemical processes, with possible diageneric ovedays. We are analyzing carbonaceous fractions of the Onaping and Onwatin to determine diagnostic C isotopic signatures Analyses by Whitehead et al. on bulk samples revealed no definitive source or processes, although delta-13 C values for "organic" C overlapped those for some meteorites. Discussion: If impact evaporation of Sudbury target carbonates did occur, then where are the carbonates? Distal carbonate (limestone/dolostone) exposures of the Espanola Formation (Huronian Supergroup) are generally thin-bedded, although remnants that partially encompass the Sudbury Crater are variable in thickness and may locally reach 250 m . If a carbonate thickness of 100-200 in existed at the target site, then copious amounts of C could have been reduced by impact processing of carbonates and also C-shale, depending on the efficiency of the processing and the amount of postimpact oxidation. Conclusion: The Sudbury crater offers a unique opportunity to study preserved characteristics of immediate carbonaceous fallback matter and particles of short-term residency in the impact plume as well as dust/aerosols from postimpact atmospheric processing.

Bunch, T. E.↗
NASA NTRS2000

A Robust Biomarker

Polymers of bacterial origin, either through cell secretion or the degraded product of cell lysis, form isolated mucoidal strands as well as well-developed biofilms on interfaces. Biofilms are structurally and compositionally complex and are readily distinguishable from abiogenic films. These structures range in size from micrometers to decimeters, the latter occurring as the well-known, mineralised biofilms called stromatolites. Compositionally bacterial polymers are greater than 90 % water, with while the majority of the macromolecules forming the framework of the polymers consisting of polysaccharides (with and some nucteic acids and proteins). These macromolecules contain a vaste amount of functional groups, such as carboxyls, hydroxyls, and phosphoryls which are implicated in cation-binding. It is the elevated metal- binding capacity which provides the bacterial polymer with structural support and also helps to preserves it for up to 3.5 b.y. in the terrestrial rock record. The macromolecules, thus, can become rapidly mineralised and trapped in a mineral matrix. Through early and late diagenesis (bacterial degradation, burial, heat, pressure and time) they break down, losing the functional groups and, gradually, their hydrogen atoms. The degraded product is known as "kerogen". With further diagenesis and metamorphism, all the hydrogen atoms are lost and the carbonaceous matter becomes graphite. until the remnant carbonaceous material become graphitised. This last sentence reads a bit as if ALL these macromolecules break down and end up as graphite., but since we find 441 this is not true for all of the macromolecules. We have traced fossilised polymer and biofilms in rocks from throughout Earth's history, to rocks as old as the oldest being 3.5 b.y.-old. Furthermore, Time of Flight Secondary Ion Mass Spectrometry has been able to identify individual macromolecules of bacterial origin, the identities of which are still being investigated, in all the samples containing fossil biofilm, including the 3.5 b.y..-old carbonaceous cherts from South Africa and Australia. As a result of the unique compositional, structural and "mineralisable" properties of bacterial polymer and biofilms, we conclude that bacterial polymers and biofilms constitute a robust and reliable biomarker for life on Earth and could be a potential biomarker for extraterrestrial life.

Westall, F.↗
NASA NTRS2000

Thermally Regenerative Battery with Intercalatable Electrodes and Selective Heating Means

The battery contains at least one electrode such as graphite that intercalates a first species from the electrolyte disposed in a first compartment such as bromine to form a thermally decomposable complex during discharge. The other electrode can also be graphite which supplies another species such as lithium to the electrolyte in a second electrode compartment. The thermally decomposable complex is stable at room temperature but decomposes at elevated temperatures such as 50 C. to 150 C. The electrode compartments are separated by a selective ion permeable membrane that is impermeable to the first species. Charging is effected by selectively heating the first electrode.

Sharma, Pramod K.↗
NASA NTRS1998

Development of High Conductivity Lithium-Ion Electrolytes for Low Temperature Cell Applications

NASA has continued interest in developing power sources which are capable of operating at low temperatures (-20 C and below) to enable future missions, such as the Mars Rover and Lander. Thus, under a program sponsored by the Mars Exploration Program, we have been involved in developing Li-ion batteries with improved low temperature performance. To accomplish this task, the focus of the research has been upon the development of advanced electrolyte systems with improved low temperature properties. This had led to the identification of a carbonate-based electrolyte, consisting of 1.0 M LiPF6 in EC + DEC + DMC (33:33:34), which has been shown to have excellent performance at -20 C in Li-ion AA-size prototype cells. Other groups are also actively engaged in developing electrolytes which can result in improved low temperature performance of Li-ion cells, including Polystor, Yardney, and Covalent. In addition to developing cells capable of operation at -20 C, there is continued interest in systems which can successfully operate at even lower temperatures (less than -30 C) and at high discharge rates (greater than C/2). Thus, we are currently focusing upon developing advanced electrolytes which are highly conductive at low temperatures and will result in cells capable of operation at -40 C. One approach to improve the low temperature conductivity of ethylene carbonate-based electrolytes involves adding co-solvents which will decrease the viscosity and extend the liquid range. Candidate solvent additives include formates, acetates, cyclic and aliphatic ethers, lactones, as well as other carbonates. Using this approach, we have prepared a number of electrolytes which contain methyl formate (MF), methyl acetate (MA), ethyl acetate (EA), ethyl proprionate (EP), and 1,2-dimethoxyethane (DME), some of which have been characterized and reported. Other groups have also reported electrolytes based on mixtures of carbonates and acetates. In the present study, electrolytes which have been identified to have good low temperature conductivity and stability were incorporated into lithium-graphite cells for evaluation. Using various electrochemical methods, including ac impedence and DC micropolarization techniques, the film formation characteristics of graphite electrodes in contact with various lectrolyte formulations was investigated.

Smart, M. C.↗
NASA NTRS2000

Growth of Carbon Nanostructure Materials Using Laser Vaporization

Since the potential applications of carbon nanotubes (CNT) was discovered in many fields, such as non-structure electronics, lightweight composite structure, and drug delivery, CNT has been grown by many techniques in which high yield single wall CNT has been produced by physical processes including arc vaporization and laser vaporization. In this presentation, the growth mechanism of the carbon nanostructure materials by laser vaporization is to be discussed. Carbon nanoparticles and nanotubes have been synthesized using pulsed laser vaporization on Si substrates in various temperatures and pressures. Two kinds of targets were used to grow the nanostructure materials. One was a pure graphite target and the other one contained Ni and Co catalysts. The growth temperatures were 600-1000 C and the pressures varied from several torr to 500 torr. Carbon nanoparticles were observed when a graphite target was used, although catalysts were deposited on substrates before growing carbon films. When the target contains catalysts, carbon nanotubes (CNT) are obtained. The CNT were characterized by scanning electron microscopy, x-ray diffraction, optical absorption and transmission, and Raman spectroscopy. The temperature-and pressure-dependencies of carbon nanotubes' growth rate and size were investigated.

Zhu, Shen↗
NASA NTRS2000

Molecular Dynamics Simulations of the Thermal Conductivity of Single-Wall Carbon Nanotubes

Carbon nanotubes (CNT) have very attractive electronic, mechanical. and thermal properties. Recently, measurements of thermal conductivity in single wall CNT mats showed estimated thermal conductivity magnitudes ranging from 17.5 to 58 W/cm-K at room temperature. which are better than bulk graphite. The cylinderical symmetry of CNT leads to large thermal conductivity along the tube axis, additionally, unlike graphite. CNTs can be made into ropes that can be used as heat conducting pipes for nanoscale applications. The thermal conductivity of several single wall carbon nanotubes has been calculated over temperature range from l00 K to 600 K using non-equilibrium molecular dynamics using Tersoff-Brenner potential for C-C interactions. Thermal conductivity of single wall CNTs shows a peaking behavior as a function of temperature. Dependence of the peak position on the chirality and radius of the tube will be discussed and explained in this presentation.

Osman, M.↗
NASA NTRS2000

Use of Guided Acoustic Waves to Assess the Effects of Thermal-Mechanical Cycling on Composite Stiffness

The introduction of new, advanced composite materials into aviation systems requires it thorough understanding of the long-term effects of combined thermal and mechanical loading. As part of a study to evaluate the effects of thermal-mechanical cycling, it guided acoustic (Lamb) wave measurement system was used to measure the bending and out-of-plane stiffness coefficients of composite laminates undergoing thermal-mechanical loading. The system uses a pulse/receive technique that excites an antisymmetric Lamb mode and measures the time-of-flight over a wide frequency range. Given the material density and plate thickness, the bending and out-of-plane shear stiffnesses are calculated from a reconstruction of the velocity dispersion curve. A series of 16 and 32-ply composite laminates were subjected to it thermal-mechanical loading profile in load frames equipped with special environmental chambers. The composite systems studied were it graphite fiber reinforced amorphous thermoplastic polyimide and it graphite fiber reinforced bismaleimide thermoset. The samples were exposed to both high and low temperature extremes its well as high and low strain profiles. The bending and out-of-plane stiffnesses for composite sample that have undergone over 6,000 cycles of thermal-mechanical loading are reported. The Lamb wave generated elastic stiffness results have shown decreases of up to 20% at 4,936 loading cycles for the graphite/thermoplastic samples and up to 64% at 4,706 loading cycles for the graphite/thermoset samples.

Seale, Michael D.↗
NASA NTRS2001

Vacuum Plasma Spray Forming of Tungsten Lorentz Force Accelerator Components

The Vacuum Plasma Spray (VPS) Laboratory at NASA's Marshall Space Flight Center has developed and demonstrated a fabrication technique using the VPS process to form anode sections for a Lorentz force accelerator from tungsten. Lorentz force accelerators are an attractive form of electric propulsion that provides continuous, high-efficiency propulsion at useful power levels for such applications as orbit transfers or deep space missions. The VPS process is used to deposit refractory metals such as tungsten onto a graphite mandrel of the desired shape. Because tungsten is reactive at high temperatures, it is thermally sprayed in an inert environment where the plasma gun melts and accelerates the metal powder onto the mandrel. A three-axis robot inside the chamber controls the motion of the plasma spray torch. A graphite mandrel acts as a male mold, forming the required contour and dimensions of the inside surface of the anode. This paper describes the processing techniques, design considerations, and process development associated with the VPS forming of the Lorentz force accelerator.

Zimmerman, Frank R.↗
NASA NTRS2001

High-Pressure Synthesis of Metal-Ceramic Nano-Composites

The major problems in fabrication of nano-crystal line materials form nano-powders are: (1), coarsening of the initial nano-size grains, (2), insufficient densification (high concentration of pores), and, (3), conversion of diamond into graphite (for diamond-based ceramics). We have developed a novel technique of the synthesis of nano-composite materials applying very high (up to about 10 GPa) pressures. In this technique, one component is pre-compacted and placed next to another having a lower melting point temperature. The whole sample is pressed and the temperature raised above the melting point of the second component, what results in the melt getting pressed into the (nano-size) pores of the compact. Upon subsequent crystallization the melt forms the second nanophase. The process is fast, on the order of seconds, and the temperatures are relatively low what prevents, or at least significantly reduces coarsening of the starting nanophase grains. Also, conversion of diamond into graphite can be prevented. The technique allows for control of the final product properties through a proper selection of (1) the initial compact density and grain size, (2) chemical composition of the source, and (3) the temperature and pressure of the process. The application of the technique to the synthesis of SiC and diamond with Si, Ge, and different metals. Results of the in-situ investigation of the synthesis process by synchrotron X-ray diffraction technique will be presented.

Gierlotka, S.↗
NASA NTRS2001

Rocket Engine Thrust Chamber Assembly

A thrust chamber assembly for liquid fueled rocket engines and the method of making it wherein a two-piece mandrel having the configuration of an assembly having a combustion chamber portion connected to a nozzle portion through a throat portion is wrapped with a silica tape saturated with a phenolic resin, the tape extending along the mandrel and covering the combustion chamber portion of the mandrel to the throat portion. The width of the tape is positioned at an angle of 30 to 50 deg. to the axis of the mandrel such that one edge of the tape contacts the mandrel while the other edge is spaced from the mandrel. The phenolic in the tape is cured and the end of the wrap is machined to provide a frusto-conical surface extending at an angle of 15 to 30 deg. with respect to the axis of the mandrel for starting a second wrap on the mandrel to cover the throat portion. The remainder of the mandrel is wrapped with a third silica tape having its width positioned at a angle of 5 to 20 deg. from the axis of the mandrel. The resin in the third tape is cured and the assembly is machined to provide a smooth outer surface. The entire assembly is then wrapped with a tow of graphite fibers wetted with an epoxy resin and, after the epoxy resin is cured, the graphite is machined to final dimensions.

Cornelius, Charles S.↗
NASA NTRS1994

Light-Hydrocarbon Bearing Solids on Planetesimal 5145 Pholus

Object 5145 Pholus (=1992 AD) is a planetesimal in an orbit that crosses those of Saturn, Uranus, and Neptune (period 92.7 years). It is particularly notable because of its extreme red color, corroborated by several observing teams. A spectrum of Pholus obtained in 1992 shows a strong absorption band with a characteristic shape at 2.27 micrometers, plus a weaker band at 1.7 micrometers. A better spectrum of the 2.0-2.5 micrometer region in 1993 confirms the position and shape of the 2.27-micrometer band. The color and spectral bands are identified with the aliphatic-rich and high H/C organic solid called asphaltite, which in a terrestrial setting originates from thermal processing of products of biological activity. In Pholus, this material is attributed to formation from radiation processing of ices on grains in the interstellar medium. Laboratory spectra of asphaltite and related materials have been published by Moroz et al., while Cloutis showed similar bands in comparable materials and identified them as the overtone and combination bands of C-H stretching and bending modes in CH2 and CH3 groups. Asphaltites, kerites, and anthraxolites are solid non-graphite members of a sequence ranging from oil to graphite; diffuse reflectance spectra of suites of these intermediate materials show color characteristics similar to those of the low-albedo asteroids (C,P,D), although specific identifications have not been made because of the lack of distinct absorption bands in the spectra of most low-albedo solar system bodies. In the case of Pholus, however, the primary band is strong; its wavelength and its shape, plus the match of the extremely red color, leads us to the identification of aliphatic-rich, asphaltite-like organic solid. The C, P, and D-type asteroids vary in degree of "redness", but are all less red than Pholus. Pholus and the Ctype asteroids are the end members of a sequence that represents the radiation processing of hydrocarbons, with Pholus being the least processed. Solar irradiation processes and heating reduce the H/C and aliphatic content of hydrocarbons preserved from the interstellar medium, and in the end produce opaque solids of neutral reflectance, including the kerogens (similar to anthraxolites) found in profusion in the carbonaceous meteorites.

Cruikshank, Dale P.↗
NASA NTRS1994

Light-Hydrocarbon Bearing Solids on Planetesimal 5145 Pholus

Object 5145 Pholus (=1992 AD) is a planetesimal in an orbit that crosses those of Saturn, Uranus, and Neptune (period 92.7 years). It is particularly notable because of its extreme red color, corroborated by several observing teams. A spectrum of Pholus obtained in 1992 shows a strong absorption band with a characteristic shape at 2.27 micron, plus a weaker band at 1.7 microns. A better spectrum of the 2.0-2.5 micron region in 1993 confirms the position and shape of the 2.27 micron band. The color and spectral bands are identified with the aliphatic-rich and high H/C organic solid called asphaltite, which in a terrestrial setting originates from thermal processing of products of biological activity. In Pholus, this material is attributed to formation from radiation processing of ices on grains in the interstellar medium. Laboratory spectra of asphaltite and related materials have been published by Moroz et al., while Cloutis showed similar bands in comparable materials and identified them as the overtone and combination bands of C-H stretching and bending modes in CH2 and CH3 groups. Asphaltites, kerites, and anthraxolites are solid non-graphite members of a sequence ranging from oil to graphite; diffuse reflectance spectra of suites of these intermediate materials show color characteristics similar to those of the low-albedo asteroids (C,P,D), although specific identifications have not been made because of the lack of distinct absorption bands in the spectra of most low-albedo solar system bodies. In the case of Pholus, however, the primary band is strong; its wavelength and its shape, plus the match of the extremely red color, leads us to the identification of aliphatic-rich, asphaltite-like organic solid. The C, P, and D-type asteroids vary in degree of 'redness', but are all less red than Pholus. Pholus and the C-type asteroids are the end members of a sequence that represents the radiation processing of hydrocarbons, with Pholus being the least processed. Solar irradiation processes and heating reduce the H/C and aliphatic content of hydrocarbons preserved from the interstellar medium, and in the end produce opaque solids of neutral reflectance, including the kerogens (similar to anthraxolites) found in profusion in the carbonaceous meteorites.

Cruikshank, Dale P.↗
NASA NTRS2001

Rocket Engine Thrust Chamber Assembly

A thrust chamber assembly for liquid fueled rocket engines and the method of making it wherein a two-piece mandrel wrapped with a silica tape saturated with a phenolic resin, the tape extending along the mandrel and covering the combustion chamber portion of the mandrel to the throat portion. The phenolic in the tape is cured and the end of the wrap is machined. The remainder of the mandrel is wrapped with a third silica tape. The resin in the third tape is cured and the assembly is machined. The entire assembly is then wrapped with a tow of graphite fibers wetted with an epoxy resin and, after the epoxy resin is cured, the graphite is machined to final dimensions.

Cornelius, Charles S.↗