Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow instability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Magnetic Measurements of Arc Instabilities in Segmented Arc Heater Column

The Aerodynamic Heating Facility (AHF) at NASA Ames Research Center (ARC) generates high enthalpy, supersonic flow environments for ground testing of NASAheat shield materials. This arc jet heater operates by passing a DC arc (<3200 A,<2500 V) through a gas column (~6 cm diameter, 2 m length) and ejecting the heated gas through a supersonic nozzle into a test chamber. The arc plasma is a partially ionized air mixture at low temperature (< 2 eV) but needs to be stable for long test times (up to 30 min) at high power (< 20 MW). Currently, the operational envelope of the facility is limited by arc instabilities including the kink instability. Consequently, it is of interest to characterize these instabilities to better understand facility limits and inform methods to extend stable operational ranges. Due to the high enthalpy and long timescales (i.e., minutes) diagnostics must be non-invasive. This work will cover the development of two sets of magnetic sensors: differential B-dot sensors and tri-axial magnetic hall sensors and will describe initial measurements of arc motion using these sensors.

Kink instability↗
DOE OSTI2022

Modeling of thermal-ion-driven internal kink in DIII-D high- T i plasmas

Toroidal modeling utilizing the non-perturbative magnetohydrodynamic-kinetic hybrid code MARS-K (Liu Y.Q. et al 2008 Phys. Plasmas 15 112503), to a DIII-D high-performance discharge with the core thermal ion temperature of T i ~ 13 keV, finds multiple branches of unstable internal kink (IK) modes triggered by the bounce resonance of trapped thermal ions. The range of the computed mode frequency aligns well with the bounce frequency of trapped thermal ions, confirming the nature of resonance drive for the instability. The computed mode frequency is close to that observed in experiments. Plasma toroidal flow, in particular the fast flow ($ > $10% of Alfvén speed) as in the considered DIII-D discharge, strongly stabilizes the fluid IK branch but not all of the thermal-ion-driven internal kink (TIK) branches, leaving one dominant unstable TIK branch under the experimental conditions. Plasma resistivity also significantly affects stability of the TIKs (but not much on the IK which is ideally strongly unstable) in combination with the drift kinetic drive by thermal ions. High resistivity can drive additional unstable TIK branches. Scanning the on-axis safety factor over a large range confirms robustness of the TIK triggering by thermal ions. The computed TIKs contain both the IK and the tearing components as the dominant contributions to the eigenmode structure. Furthermore, these findings, together with the experimental results reported in reference (Du X.D. et al 2021 Phys. Rev. Lett. 127 025001), strongly suggest the possibility of thermal-ion driven instabilities in ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Flux Eruption Events Drive Angular Momentum Transport in Magnetically Arrested Accretion Flows

We evolve two high-resolution general relativistic magnetohydrodynamic simulations of advection-dominated accretion flows around nonspinning black holes (BHs), each over a duration ~3 × 10 5 GM BH /c 3 . One model captures the evolution of a weakly magnetized (SANE) disk and the other that of a magnetically arrested disk (MAD). Magnetic flux eruptions in the MAD model push out gas from the disk and launch strong winds with outflow efficiencies at times reaching 10% of the incoming accretion power. Despite the substantial power in these winds, average mass outflow rates remain low out to a radius ~100GM BH /c 2 , only reaching ~60%–80% of the horizon accretion rate. The average outward angular momentum transport is primarily radial in both modes of accretion, but with a clear distinction: magnetic flux eruption–driven disk winds cause a strong vertical flow of angular momentum in the MAD model, while for the SANE model, the magnetorotational instability (MRI) moves angular momentum mostly equatorially through the disk. Further, we find that the MAD state is highly transitory and nonaxisymmetric, with the accretion mode often changing to a SANE-like state following an eruption before reattaining magnetic flux saturation with time. The Reynolds stress changes directions during such transitions, with the MAD (SANE) state showing an inward (outward) stress, possibly pointing to intermittent MRI-driven accretion in MADs. Pinning down the nature of flux eruptions using next-generation telescopes will be crucial in understanding the flow of mass, magnetic flux, and angular momentum in sub-Eddington accreting BHs like M87* and Sagittarius A*.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1990

Numerical prediction of turbulent flame stability in premixed/prevaporized (HSCT) combustors

A numerical analysis of combustion instabilities that induce flashback in a lean, premixed, prevaporized dump combustor is performed. KIVA-II, a finite volume CFD code for the modeling of transient, multidimensional, chemically reactive flows, serves as the principal analytical tool. The experiment of Proctor and T'ien is used as a reference for developing the computational model. An experimentally derived combustion instability mechanism is presented on the basis of the observations of Proctor and T'ien and other investigators of instabilities in low speed (M less than 0.1) dump combustors. The analysis comprises two independent procedures that begin from a calculated stable flame: The first is a linear increase of the equivalence ratio and the second is the linear decrease of the inflow velocity. The objective is to observe changes in the aerothermochemical features of the flow field prior to flashback. It was found that only the linear increase of the equivalence ratio elicits a calculated flashback result. Though this result did not exhibit large scale coherent vortices in the turbulent shear layer coincident with a flame flickering mode as was observed experimentally, there were interesting acoustic effects which were resolved quite well in the calculation. A discussion of the k-e turbulence model used by KIVA-II is prompted by the absence of combustion instabilities in the model as the inflow velocity is linearly decreased. Finally, recommendations are made for further numerical analysis that may improve correlation with experimentally observed combustion instabilities.

Winowich, Nicholas S.↗
NASA NTRS1980

A model for broadband jet noise amplification

A model is proposed for the change in turbulent structure of a round jet in the presence of an acoustic excitation. The excitation is assumed to trigger instability waves of a known initial amplitude at the jet exit. As these waves propagate downstream they extract energy from the mean flow and transfer it to the random turbulence. This results in an increase in the levels of the turbulence and a resulting increase in the radiated broadband noise. No calculations are presented for the noise radiation; however, an examination is made of the effect of excitation level and frequency on the jet flow. The numerical procedure allows for radial as well as axial variations in the averaged properties of jet to be calculated. The results indicate that the presence of a finite amplitude instability wave increases the spreading of the jet. It does not vary the characteristic radial shapes of both the axial mean velocity and the turbulent kinetic energy. An energy budget for the random turbulence shows that it is fed energy from the excited wave predominantly on each side of the jet lip line. This results in a broader radial shape for the turbulent kinetic energy.

Morris, P. J.↗
NASA NTRSDate not supplied

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗
NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗
NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗
NASA NTRS1992

Fully coupled resonant-triad interaction in an adverse-pressure-gradient boundary layer

The nonlinear resonant-triad interaction, proposed by Raetz (1959), Craik (1971), and others for a Blasius boundary layer, is analyzed here for an adverse-pressure-gradient boundary layer. We assume that the adverse pressure gradient is in some sense weak and, therefore, that the instability growth rate is small. This ensures that there is a well-defined critical layer located somewhere within the flow and that the nonlinear interaction is effectively confined to that layer. The initial interaction is of the parametric resonance type, even when the modal amplitudes are all of the same order. This means that the oblique instability waves exhibit faster than exponential growth and that the growth rate of the two-dimensional mode remains linear. However, the interaction and the resulting growth rates become fully coupled, once oblique-mode amplitudes become sufficiently large, but the coupling terms are now quartic, rather than quadratic as in the Craik (1971) analysis. More importantly, however, new nonlinear interactions, which were not present in the Craik-type analyses, now come into play. These interactions eventually have a dominant effect on the instability wave development.

Goldstein, M. E.↗
NASA NTRS1978

Concerning isothermal self-similar blast waves. I - One-dimensional flow and its stability. II - Two-dimensional flow and its stability

One-dimensional self-similar isothermal flow behind a blast wave propagating in a medium whose density varies with distance is investigated for the cases of one-dimensional and two-dimensional flow. The isothermal flow model is adopted as an alternative to adiabatic models of self-similar flow, which neglect heat flux. The topology of the one-dimensional flow solutions, the singularities, and the influence of boundary conditions are discussed; the instability of the isothermal blast waves against nonself-similar perturbations is also considered. The number of critical points in the two-dimensional solutions is found to vary from the number in the one-dimensional problem.

Lerche, I.↗
NASA NTRS1985

Theoretical and experimental studies of baroclinic processes

An experimental study in a baroclinic annulus with heating and cooling on the upper and lower horizontal surfaces was completed. Four basic regimes of flow were observed: (1) axisymmetric flow, (2) cellular (deep) convection, (3) convective rolls (boundary layer), and (4) baroclinic instability. There was no symmetric (or nearly symmetric) baroclinic instability observed, although it was determined by numerical calculations that we transversed regions in parameter space where the symmetric instability was present. The non-symmetric baroclinic instability (Eady type) was observed instead. Although the vertical depth was rather small and hence viscous damping was strong, large-amplitude baroclinic waves were made possible by imposing a very weak static stability.

Miller, T.↗
NASA NTRS1986

On the interpretation of the beta(sub p) relation in interstellar clouds

Troland and Heiles (1986) have recently presented an updated compilation of observational data concerning the relationship between the interstellar magnetic field strength B and the gas density rho (or, equivalently, the particle density n). One of the main findings of their survey was that B remains constant over the density range 0.1 - approx. 100 cu. cm and shows evidence for increase only a higher densities. They compared this result with theoretical predictions based on the Parker-instability scenario for the formation and evolution of interstellar clouds in the presence of the galactic magnetic field. In this picture, low-density gas is driven by the magnetic Rayleigh-Taylor instability into magnetic valleys, where it accumulates into denser concentrations. The gas initially flows along the magnetic field lines and there is little increase of the field strength with density; B only starts to rise when n becomes large enough for self-gravity to begin competing with the magnetic stresses. For a cloud mass of approx. 1,000 sub M and the measured background field strength, the critical density for contraction in approx. 75 cu. cm. Troland and Heiles therefore concluded that this scenario is basically consistent with the observations. This conclusion is debated.

Koenigl, A.↗
NASA NTRS1988

On the preferred mode of jet instability

The preferred mode of instability was investigated in an axisymmetric air jet of moderate Reynolds number. Natural instabilities are shown to scale with local shear-layer thickness and the preferred mode is shown to be a shear-layer instability. The spatial evolution of the preferred mode was examined by exciting the flow acoustically and then mapping the phase-locked velocity fluctuations. Throughout the potential core region the phase-locked profiles are shown to agree with the eigensolutions of the Orr-Sommerfeld stability equations provided the calculations are based on measured, mean velocity profiles. The excitation intensity was varied from low levels, where the flow was merely tagged, to high levels where the mean flow was substantially distorted, and over that range of excitation there was no apparent deterioration in the agreement with stability predictions.

Petersen, R. A.↗
NASA NTRS1989

Wind-disk shocks around T Tauri stars

It is suggested that the winds of T Tauri stars are heated at distances of 50-100 AU by oblique shocks with circumstellar disks, producing the observed high-velocity forbidden-line emission. The low shock velocities characteristic of this model provide low-excitation emission and line profiles in reasonable agreement with observations. The blueshifted character of the observed emission is explained by a combination of disk occultation of the receding flow, plus a modest collimation of the observable wind by the disk envelope. Instabilities at the wind-disk interface may be important in producing the observed emission.

Hartmann, Lee↗
NASA NTRS1987

Stability theory applications to laminar-flow control

In order to design Laminar Flow Control (LFC) configurations, reliable methods are needed for boundary-layer transition predictions. Among the available methods, there are correlations based upon R sub e, shape factors, Goertler number and crossflow Reynolds number. The most advanced transition prediction method is based upon linear stability theory in the form of the e sup N method which has proven to be successful in predicting transition in two- and three-dimensional boundary layers. When transition occurs in a low disturbance environment, the e sup N method provides a viable design tool for transition prediction and LFC in both 2-D and 3-D subsonic/supersonic flows. This is true for transition dominated by either TS, crossflow, or Goertler instability. If Goertler/TS or crossflow/TS interaction is present, the e sup N will fail to predict transition. However, there is no evidence of such interaction at low amplitudes of Goertler and crossflow vortices.

Malik, Mujeeb R.↗
NASA NTRS1990

Transition to hard turbulence in thermal convection at infinite Prandtl number

Direct numerical simulations of two-dimensional high Rayleigh (Ra) number, base-heated thermal convection in large aspect-ratio boxes are presented for infinite Prandtl number fluids, as applied to the earth's mantle. A transition is characaterized in the flow structures in the neighborhood of Ra between 10 to the 7th and 10 to the 8th. These high Ra flows consist of large-scale cells with strong intermittent, boundary-layer instabilities. For Ra exceeding 10 to the 7th it is found that the heat-transfer mechanism changes from one characterized by mushroom-like plumes to one consisting of disconnected ascending instabilities, which do not carry with them all the thermal anomaly from the bottom boundary layer. Plume-plume collisions become much more prominent in high Ra situations and have a tendency of generating a pulse-like behavior in the fixed plume. This type of instability represents a distinct mode of heat transfer in the hard turbulent regime. Predictions of this model can be used to address certain issues concerning the mode of time-dependent convection in the earth's mantle.

Hansen, Ulrich↗