Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composite models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Effects of thermal loading on foil and sheet composites with constituents of differing thermal expansivities.

A study was made to estimate the magnitudes of elastic stresses and elastic-plastic stresses and strains in sheet or foil laminar composites. Using a model tungsten/80Ni + 20Cr laminar composite and assuming cooling or heating through a temperature range of 80-2000 deg F (26.5-1093.5 deg C), calculated elastic stresses exceeded published or estimated strengths of the constituents. Elastic-plastic stress-strain solutions resulted in lower estimated stress levels but with the concomitant occurrence of sufficiently large strain ranges to suggest possible thermal fatigue problems. Limited experimental studies using tungsten/80Ni + 20Cr foil and sheet laminar composites, slowly cycled between 80 and 2000 deg F (26.5-1093.5 deg C) or rapidly cycled between 80 and 1600 deg F (26.5-871 deg C) produced varying degrees of observable structural damage in from 1 to 11 cycles depending upon temperature transition rate and laminae thickness; these particular results might not occur with other combinations of materials.

Hoffman, C. A.↗

Observation of additional low-degree 5-min modes of solar oscillation

High-order solar oscillations with degrees l=3, 4, and 5 could be detected. The observations were made by measuring the difference between the shifts in the Fe 5,124 spectrum line from light integrated from a central circular portion of the solar disk and from an annular portion exterior to it. The frequencies of the octupole modes agree well with the values obtained from whole-disk measurements at the South Pole. A least-squares fit of the observed frequencies to values interpolated between and extrapolated from the predictions of a sequence of solar models with different chemical compositions selects two models. One, a helium-rich solution, agrees with that of similar analyses of whole-disk data. The extrapolated solution has a relatively deep convection zone, and is thus consistent with analyses of 5-min oscillations of high degree.

Scherrer, P. H.↗

Measurements of the gas temperature and iron abundance distribution in the Coma Cluster

The medium energy X-ray detectors onboard the EXOSAT Observatory have been used to determine the gas temperature at several positions in the Coma Cluster of galaxies. Evidence is found at greater than 95 percent confidence for a higher temperature in the center of the cluster than in a position approximately 45 arcmin off-center. No difference in iron abundance is observed between the center and off-center regions and the equilibrium model for the distribution of elements in the Coma Cluster of Abramopoulos, Chanan, and Ku can be rejected with greater than 99.5 percent confidence, in favor of a model with more uniform composition. A phenomenological model is presented of the Coma Cluster, which is consistent with the data presented here, as well as the imaging data from the Einstein Observatory and the Tenma X-ray spectrum. The model has a central isothermal region of temperature about 9 keV extending to about 25 arcmin (about 1 Mpc). Beyond this radius the temperature falls as a polytrope with index about 1.6.

Hughes, John P.↗

Radiation fluxes at the FIFE site

The main objective of the International Satellite Land Surface Climatology Project (ISLSCP) has been stated as 'the development of techniques that may be applied to satellite observations of the radiation reflected and emitted from the Earth to yield quantitative information concerning land surface climatological conditions'. The major field study, FIFE (the First ISLSCP Field Experiment), was conducted in 1987-89 to accomplish this objective. Four intensive field campaigns (IFC's) were carried out in 1987 and one in 1989. Factors contributing to observed reflected radiation from the FIFE site must be understood before the radiation observed by satellites can be used to quantify surface processes. Our last report (Walter-Shea et al., 1992b) focused on slope effects on incoming and outgoing shortwave radiation and net radiation from data collected in 1989. We report here on the final analysis of the slope data as well as results from thermal radiation studies conducted during the FIFE experiment. The specific areas reported are the following: (1) analysis of slope effects on measured reflectance values and estimates of surface albedo; (2) using remotely-measured surface temperatures as a means of estimating sensible heat flux from the Konza Prairie; (3) extracting canopy temperatures from remotely-measured composite surface temperatures; (4) modeling the measured composite temperature of partially vegetated surfaces; and (5) estimating gap distribution in partially vegetated surfaces from reflectance measurements.

Walter-Shea, Elizabeth A.↗

STOP Modeling for the JWST: Techniques, Results, and Sensitivities

The James Web Space Telescope (JWST) is a large, infrared-optimized, space telescope scheduled for launch to L2 in 2011. It must meet rigorous thermal stability requirements, almost all of which will be verified through analysis. Terrestrial testing will be performed but even that will require significant analytical interpretation of results. Preliminary analysis indicates that traditional second-order effects could cause the telescope to exceed established performance requirements. This leads to very large detailed models, primarily since composite tubes are being modeled using solid elements. To minimize differences between the current baseline and the model the project is using a number of rapid analysis cycles. The large size of the telescope models and the short cycle time creates a demanding multidisciplinary analysis environment.

John D. Johnston↗

The X-ray Halo of GX5-1

Using Chandra observations we have measured the energy-resolved dust-scattered X-ray halo around the low-mass X-ray binary GX5-1, detecting for the first time multiply scattered X-rays from interstellar dust. % e compared the observed X-ray halo at various energies to predictions from a range of dust models. These fits used both smoothly-distributed dust as well as dust in clumped clouds, with CO and 21 cm observations helping to determine the position of the clouds along the line of sight. We found that the BARE-GR-B model of Zubko, Dwek & Arendt (2004) generally led to the best results, although inadequacies in both the overall model and the data limit our conclusions. We did find that the composite dust models of Zubko, Dwek & Arendt (2004), especially the "no carbon" models, gave uniformly poor results. Although models using cloud positions and densities derived naively from CO and 21 cm data gave generally poor results, plausible adjustments to the distance of the largest cloud and the mass of a cloud in the expanding 3 kpc Arm lead to significantly improved fits. We suggest that combining X-ray halo, CO, and 21 cm observations will be a fruitful method to improve our understanding of both the gas and dust phases of the interstellar medium.

Smith, Randall K.↗

Exoplanet Transit Spectroscopy Using WFC3: WASP-12 b, WASP-17 b, and WASP-19 b

We report an analysis of transit spectroscopy of the extrasolar planets WASP-12 b, WASP-17 b, and WASP-19 b using the Wide Field Camera 3 (WFC3) on the Hubble Space Telescope (HST). We analyze the data for a single transit for each planet using a strategy similar, in certain aspects, to the techniques used by Berta et al., but we extend their methodology to allow us to correct for channel- or wavelength-dependent instrumental effects by utilizing the band-integrated time series and measurements of the drift of the spectrum on the detector over time. We achieve almost photon-limited results for individual spectral bins, but the uncertainties in the transit depth for the band-integrated data are exacerbated by the uneven sampling of the light curve imposed by the orbital phasing of HST's observations. Our final transit spectra for all three objects are consistent with the presence of a broad absorption feature at 1.4 nano meter most likely due to water. However, the amplitude of the absorption is less than that expected based on previous observations with Spitzer, possibly due to hazes absorbing in the NIR or non-solar compositions. The degeneracy of models with different compositions and temperature structures combined with the low amplitude of any features in the data preclude our ability to place unambiguous constraints on the atmospheric composition without additional observations with WFC3 to improve the signal-to-noise ratio and/or a comprehensive multi-wavelength analysis.

Atmospheres↗

Exoplanet Transit Spectroscopy Using WFC3: WASP-12b, WASP-17b, and WASP-19b

We report an analysis of transit spectroscopy of the extrasolar planets WASP-12 b, WASP-17 b, and WASP-19 b using the Wide Field Camera 3 (WFC3) on the Hubble Space Telescope (HST). We analyze the data for a single transit for each planet using a strategy similar, in certain aspects, to the techniques used by Berta et al., but we extend their methodology to allow us to correct for channel- or wavelength-dependent instrumental effects by utilizing the band-integrated time series and measurements of the drift of the spectrum on the detector over time. We achieve almost photon-limited results for individual spectral bins, but the uncertainties in the transit depth for the band-integrated data are exacerbated by the uneven sampling of the light curve imposed by the orbital phasing of HST's observations. Our final transit spectra for all three objects are consistent with the presence of a broad absorption feature at 1.4 microns most likely due to water. However, the amplitude of the absorption is less than that expected based on previous observations with Spitzer, possibly due to hazes absorbing in the NIR or non-solar compositions. The degeneracy of models with different compositions and temperature structures combined with the low amplitude of any features in the data preclude our ability to place unambiguous constraints on the atmospheric composition without additional observations with WFC3 to improve the signal-to-noise ratio and/or a comprehensive multi-wavelength analysis. Key words: planetary systems - techniques: photometric - techniques: spectroscopic

HST↗

Deep Geothermal Reservoir Temperatures in the Eastern Snake River Plain, Idaho using Multicomponent Geothermometry

The U.S. Geological survey has estimated that there are up to 4,900 MWe of undiscovered geothermal resources and 92,000 MWe of enhanced geothermal potential within the state of Idaho. Of particular interest are the resources of the Eastern Snake River Plain (ESRP) which was formed by volcanic activity associated with the relative movement of the Yellowstone Hot Spot across the state of Idaho. This region is characterized by a high geothermal gradient and thermal springs occurring along the margins of the ESRP. Masking much of the deep thermal potential of the ESRP is a regionally extensive and productive cold-water aquifer. We have undertaken a study to infer the temperature of the geothermal system hidden beneath the cold-water aquifer of the ESRP. Our approach is to estimate reservoir temperatures from measured water compositions using an inverse modeling technique (RTEst) that calculates the temperature at which multiple minerals are simultaneously at equilibrium while explicitly accounting for the possible loss of volatile constituents (e.g., CO2), boiling and/or water mixing. In the initial stages of this study, we apply the RTEst model to water compositions measured from a limited number of wells and thermal springs to estimate the regionally extensive geothermal system in the ESRP.

15 GEOTHERMAL ENERGY↗

Microalgae Commodities from Coal-Fired Power Plant Flue Gas CO 2 (Draft Final Report, October 1, 2015 to June 30, 2018)

The Orlando Utilities Commission (OUC) operates an approximately 900-MWe coal fired-power plant at Stanton Energy Center (SEC), which was the site for this project to develop an integrated process for microalgae utilization of flue gas CO 2 for the production of biofuels and animal feeds. Microalgae have both potentially high yields (tons biomass/acre-year) and can be used for biofuels or high value animal feeds. The high biomass yields of microalgae cultures allows efficient use of land and water resources. They can also use wastewaters, recycle fertilizers, and have lower overall greenhouse gas emissions than conventional biofuels or animal feeds. However, many technical issues and technology gaps related to large-scale algae biomass production still must be resolved before such a process can be scaled-up. In this project, techno-economic analyses (TEAs) and life cycle assessments (LCAs) were carried out, projecting the costs and impacts of large-scale algae biomass cultivation for production of biofuels and animal feeds using OUC-SEC flue gas CO 2 . In addition, 3.5-m 2 (~ 40-ft 2 ) experimental raceway ponds were used for the cultivation of microalgae at OUC-SEC and also at the University of Florida. A large-scale algae farm was designed for a 1,300-acre site (~500-ha) located near the OUC-SEC plant, consisting of 400 hectares (1,000 acres) of paddle wheel mixed raceway ponds (each 4 ha), receiving flue gas piped approximately 3 km (2 miles) from the SEC plant. In the first year of this project (Budget Period 1, BP1), the TEA and LCA studies focused on the production of biogas produced from algae biomass and its use to replace coal at the power plant. However, due to the resulting very high cost of CO 2 mitigation, the process was modified to produce compressed natural gas (‘renewable natural gas’, RNG) for transportation fuel from the biogas, in conjunction with wastewater treatment by the algae cultures. During Budget Period 2 (BP2), the TEA and LCA studies focused on the production of animal feeds by the algae farm, using fresh water and agricultural fertilizers. In this case, CO 2 mitigation costs would be entirely covered if the algal biomass could be sold at between a two to three-fold premium above soybean feed, based on a higher nutritional value for the algal biomass. In support of the above analyses, microalgae cultivation experiments were carried out for over two years during this project in small 3.5-m 2 ponds at both SEC and the University of Florida. The most important results were the demonstration at SEC of the cultivation, on flue gas CO 2 , of filamentous algae biomass, which can be harvested at much lower cost than processes required for the colloidal algae species, as currently used by almost all algal mass culture biofuels and animal feeds projects. The yield of biogas production from the algal biomass was investigated by the University of Florida, and the value of the algal biomass as animal feed was projected based on biochemical analysis of the SEC ad UF biomasses. The conclusion from TEA/LCA carried out for the biogas case in BP1 was that a 400-ha algae system producing biomethane for co-firing at OUC-SEC could generate 27,500 MWh/yr of renewable power, offsetting 28,400 Mg CO 2eq /yr, which amounted to less than 1% of the CO 2 emitted by the SEC plant. (Mg = metric ton = 1.10 short tons). The overall cost was projected at $820/Mg of CO 2eq reduction, making this process unfeasible under any possible scenario. More favorable economics were projected when the biogas was converted to higher value transportation fuel, RNG, which also would benefit from renewable fuel (RINs) and possibly other credits. However, only by combining RNG production with municipal wastewater treatment in the algal ponds would CO 2 utilization result in no net cost or even be economically beneficial (i.e., generate income to the power plant). However, in that case the amount of CO 2 utilization would be even lower than that in the biogas case, because a large fraction of the carbon required would be supplied from the wastewater and CO 2 recovered during biogas upgrading to RNG. In brief, use of power plant CO 2 emissions for algal biofuels production was not favorable, even with optimistic assumptions about biomass productivity and biogas yields. For the animal feed case, developed during BP2, algal biomass would replace soybean feeds. The same scale 400-ha algal production plant was projected to produce 26,280 Mg per year of animal feed with a utilization of 45,300 Mg flue gas CO 2 taken up by the algal biomass. However, the process would result in a projected reduction of 112,500 Mg CO 2eq emissions per year, or roughly 1.9% of OUC-SEC emissions, mainly due to the large CO 2eq emissions from conventional soybean production. A major factor in this analysis were greenhouse gas emissions from land use changes. The cost of CO 2 utilization was projected at $116/Mg if the biomass sold for the same price as soybean meal, but if sold as a premium feed (e.g., based on high omega-3 fatty acid and carotenoid content), the power plant could actually charge for the CO 2 utilized. These economic projections are sensitive to assumptions underlying the TEA and LCA models, including biomass composition and the financial models used to project CAPEX and OPEX. Further development of an algal animal feed production using coal-fired power plant flue gas CO 2 is recommended based on the TEA and LCA, as well as experimental results. The required research and development is detailed in a technology gap analysis (Section 11), which focuses on the demonstrations of the cultivation of higher value filamentous algal biomass at OUC-SEC.

01 COAL, LIGNITE, AND PEAT↗

Evaluation of several micromechanics models for discontinuously reinforced metal matrix composites

A systematic experimental evaluation of whisker and particulate reinforced aluminum matrix composites was conducted to assess the variation in tensile properties with reinforcement type, volume fraction, and specimen thickness. Each material was evaluated in three thicknesses, 1.8, 3.18, and 6.35 mm, to determine the size, distribution, and orientation of the reinforcements. This information was used to evaluate several micromechanical models that predict composite moduli. The longitudinal and transverse moduli were predicted for reinforced aluminum. The Paul model, the Cox model and the Halpin-Tsai model were evaluated. The Paul model gave a good upper bound prediction for the particulate reinforced composites but under predicted whisker reinforced composite moduli. The Cox model gave good moduli predictions for the whisker reinforcement, but was too low for the particulate. The Halpin-Tsai model gave good results for both whisker and particulate reinforced composites. An approach using a trigonometric projection of whisker length to predict the fiber contribution to the modulus in the longitudinal and transverse directions was compared to the more conventional lamination theory approach.

Johnson, W. Steven↗

Comparison of some micromechanics models for discontinuously reinforced metal matrix composites

A systematic experimental evaluation of whisker and particulate reinforced aluminum matrix composites was conducted to assess the variation in tensile properties with reinforcement type, volume fraction, and specimen thickness. Each material was evaluated in three thicknesses, 1.8, 3.18, and 6.35 mm, to determine the size, distribution, and orientation of the reinforcements. This information was used to evaluate several micromechanical models that predict composite moduli. The longitudinal and transverse moduli were predicted for reinforced aluminum. The Paul model, the Cox model and the Halpin-Tsai model were evaluated. The Paul model gave a good upper bound prediction for the particulate reinforced composites but under predicted whisker reinforced composite moduli. The Cox model gave good moduli predictions for the whisker reinforcement, but was too low for the particulate. The Halpin-Tsai model gave good results for both whisker and particulate reinforced composites. An approach using a trigonometric projection of whisker length to predict the fiber contribution to the modulus in the longitudinal and transverse directions was compared to the more conventional lamination theory approach.

Johnson, W. S.↗

Neutron diffraction measurements and modeling of residual strains in metal matrix composites

Neutron diffraction measurements at room temperature are used to characterize the residual strains in tungsten fiber-reinforced copper matrix, tungsten fiber-reinforced Kanthal matrix, and diamond particulate-reinforced copper matrix composites. Results of finite element modeling are compared with the neutron diffraction data. In tungsten/Kanthal composites, the fibers are in compression, the matrix is in tension, and the thermal residual strains are a strong function of the volume fraction of fibers. In copper matrix composites, the matrix is in tension and the stresses are independent of the volume fraction of tungsten fibers or diamond particles and the assumed stress free temperature because of the low yield strength of the matrix phase.

Saigal, A.↗

Atomistic models of Cu diffusion in CuInSe 2 under variations in composition

Here we construct an analytic model for the composition dependence of the vacancy-mediated Cu diffusion coefficient in undoped CuInSe 2 using parameters from density functional theory. The applicability of this model is supported numerically with kinetic lattice Monte Carlo and Onsager transport tensors. We discuss how this model relates to experimental measurements of Cu diffusion, arguing that our results can account for significant contributions to the bulk diffusion of Cu tracers in non-stoichiometric CuInSe 2 .

74 ATOMIC AND MOLECULAR PHYSICS↗

MATRIX 2 RESULTS OF THE FY07 ENHANCED DOE HIGH-LEVEL WASTE MELTER THROUGHPUT STUDIES AT SRNL

High-level waste (HLW) throughput (i.e., the amount of waste processed per unit time) is a function of two critical parameters: waste loading (WL) and melt rate. For the Waste Treatment and Immobilization Plant (WTP) at the Hanford Site and the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS), increasing HLW throughput would significantly reduce the overall mission life cycle costs for the Department of Energy (DOE). The objective of this study was to generate supplemental validation data that could be used to determine the applicability of the current liquidus temperature (TL) model to expanded DWPF glass composition regions of interest based on higher WLs. Two specific flowsheets were used in this study to provide such insight: (1) Higher WL glasses (45 and 50%) based on future sludge batches that have (and have not) undergone the Al-dissolution process. (2) Coupled operations supported by the Salt Waste Processing Facility (SWPF), which increase the TiO{sub 2} concentration in glass to greater than 2 wt%. Glasses were also selected to address technical issues associated with Al{sub 2}O{sub 3} solubility, nepheline formation, and homogeneity issues for coupled operations. A test matrix of 28 glass compositions was developed to provide insight into these issues. The glasses were fabricated and characterized using chemical composition analysis, X-ray Diffraction (XRD), TL measurement and the Product Consistency Test (PCT). The results of this study are summarized below: (1) TiO{sub 2} concentrations up to {approx} 3.5 wt% were retained in DWPF type glasses, where retention is defined as the absence of crystalline TiO{sub 2} (i.e., unreacted or undissolved) in the as-fabricated glasses. Although this TiO{sub 2} content does not bound the projected SWPF high output flowsheet (up to 6 wt% TiO{sub 2} may be required in glass), these data demonstrate the potential for increasing the TiO{sub 2} limit in glass above the current limit of 2 wt% (based strictly on retention or solubility). (2) For those study glasses that had very close compositional overlap with the model development and/or model validation ranges of the current DWPF TL model (except TiO{sub 2} and MgO concentrations), there was very little difference in the predicted and measured TL values. Even though the TiO{sub 2} concentrations were above the 2 wt% upper limit, the results indicate that the current T{sub L} model is applicable in this compositional region with TiO{sub 2} contents up to approximately 3.5 wt%. (3) As the target glass compositions diverge from the model development and validation ranges, the T{sub L} data suggest that the model under-predicted the measured values. These discrepancies imply that there are individual oxides or oxide combinations that need to be accounted for in the model. These oxides include B{sub 2}O{sub 3}, SiO{sub 2}, MnO, TiO{sub 2} and/or their combinations. More data would be required to fill in these anticipated DWPF compositional regions for higher WL glasses so that the model coefficients could be refit to account for these differences. (4) Based on PCT response of HWL-21 and HWL-22 (two glasses that were prone to nepheline formation) it appears that increasing the B{sub 2}O{sub 3} concentration in glass does not consistently suppress the formation of nepheline in glasses with higher Al{sub 2}O{sub 3} and/or Na{sub 2}O content. Although the chemical durabilities of the quenched versions of these glasses were very acceptable, the canister centerline cooled (ccc) glasses exhibited a considerable decrease in durability and were found to contain nepheline via XRD. In fact, one of the glasses had a release that was 5 times greater than that of the Environmental Assessment (EA) benchmark glass. These results suggest a need for a more fundamental understanding of the compositional and kinetic effects of nepheline formation in high WL glasses. (5) Data have been generated in support of the replacement of the homogeneity constraint with the Al{sub 2}O{sub 3} and/or sum of alkali constraints for coupled operations as previously completed for sludge-only operations. This strategy should be pursued for either the compositional region anticipated for coupled operations or as part of the variability study for each sludge batch. The PCT responses of the study glasses suggest a high probability that this strategy could be defended at some later date.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Model calibration and validation for OFMSW and sewage sludge co-digestion reactors

Highlights: > Disintegration is the limiting step of the anaerobic co-digestion process. > Disintegration kinetic constant does not depend on the waste particle size. > Disintegration kinetic constant depends only on the waste nature and composition. > The model calibration can be performed on organic waste of any particle size. - Abstract: A mathematical model has recently been proposed by the authors to simulate the biochemical processes that prevail in a co-digestion reactor fed with sewage sludge and the organic fraction of municipal solid waste. This model is based on the Anaerobic Digestion Model no. 1 of the International Water Association, which has been extended to include the co-digestion processes, using surface-based kinetics to model the organic waste disintegration and conversion to carbohydrates, proteins and lipids. When organic waste solids are present in the reactor influent, the disintegration process is the rate-limiting step of the overall co-digestion process. The main advantage of the proposed modeling approach is that the kinetic constant of such a process does not depend on the waste particle size distribution (PSD) and rather depends only on the nature and composition of the waste particles. The model calibration aimed to assess the kinetic constant of the disintegration process can therefore be conducted using organic waste samples of any PSD, and the resulting value will be suitable for all the organic wastes of the same nature as the investigated samples, independently of their PSD. This assumption was proven in this study by biomethane potential experiments that were conducted on organic waste samples with different particle sizes. The results of these experiments were used to calibrate and validate the mathematical model, resulting in a good agreement between the simulated and observed data for any investigated particle size of the solid waste. This study confirms the strength of the proposed model and calibration procedure, which can thus be used to assess the treatment efficiency and predict the methane production of full-scale digesters.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Helium in Stream Water as a Volcanic Monitoring Tool

Abstract We show that synoptic sampling of streams can be used to characterize volcanic volatiles in groundwater over large spatial scales. Synoptic sampling of dissolved noble gases, 222 Rn, major ions, and stream discharge was carried out along a 30 km reach of the Gibbon River, near Norris Geyser Basin in Yellowstone National Park, USA. Groundwater discharge location, volume, and composition were estimated by constrained calibration of a stream flow and solute transport model. Estimated groundwater composition from stream modeling was compared to shallow groundwater concentrations measured in nearby springs. 3 He, 222 Rn, and Cl signatures in the Gibbon River are indicative of groundwater discharge with a volcanic signature along the study reach. Stream water noble gas isotopic composition has similar isotopic mixing patterns to springs. The model‐estimated composition of groundwater discharging to the Gibbon agrees well with observed groundwater composition from nearby springs for all modeled analytes. We present the first observations of elevated mantle helium in stream water and show that stream water can be used as a convenient collection point to estimate spatially distributed groundwater composition and to monitor changes in volatile flux over large spatial areas. These results offer the possibility that stream surveys in volcanic terrain could be a new method for distributed volcanic monitoring at the catchment scale and beyond.

Gardner, W. Payton↗

Development of a Numerical Modeling Approach for Buckling Analysis of Sandwich Composite Cylindrical Shells with Selected Results

The buckling response of geometrically perfect and imperfect cylindrical sandwich shells can be investigated using nonlinear finite element analyses with two-dimensional general-purpose shell elements. Such analyses are used in the NASA Engineering and Safety Center Shell Buckling Knockdown Factor Project, which has the goal of developing new analysis-based buckling design recommendations for select classes of sandwich composite cylindrical structures under uniaxial compressive load. As such, finite element models of sandwich composite cylinders were developed and analyses were performed to predict the buckling responses of geometrically perfect and imperfect sandwich composite cylinders. The development of the selected finite-element modeling approach for a sandwich composite cylinder is discussed. Buckling-response sensitivity of geometrically imperfect sandwich cylinders for various shell element types were investigated as part of this study. Preliminary results of geometric imperfections influence on buckling response of sandwich cylinders are also presented.

Structural Modeling↗