Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “bonding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Bonding aluminum beam leads

Report makes it relatively easy for hybrid-circuit manufacturers to convert integrated circuit chips with aluminum bead leads. Report covers: techniques for handling tiny chips; proper geometries for ultrasonic bonding tips; best combinations of pressure, pulse time, and ultrasonic energy for bonding; and best thickness for metal films to which beam leads are bonded.

Burkett, F. S.↗

Discrete component bonding and thick film materials study

The bonding reliability of discrete capacitor chips bonded with solders and conductive epoxies was examined along with the thick film resistor materials consisting of iron oxide phosphate and vanadium oxide phosphates. It was concluded from the bonding reliability studies that none of the wide range of types of solders examined is capable of resisting failure during thermal cycling while the conductive epoxy gives substantially lower failure rates. The thick film resistor studies proved the feasibility of iron oxide phosphate resistor systems although some environmental sensitivity problems remain. One of these resistor compositions has inadvertently proven to be a candidate for thermistor applications because of the excellent control achieved upon the temperature coefficient of resistance. One new and potentially damaging phenomenon observed was the degradation of thick film conductors during the course of thermal cycling.

Kinser, D. L.↗

Argon hydrochloride, Ar.HCl, bond energy by infrared spectroscopy

The infrared absorption of argon (200 to 760 torr) and hydrogen chloride (2 to 6 torr) mixtures is reexamined in the missing Q branch region (spectral region between 2860 and 3010 wavelength/cm) at temperatures ranging from 195 to 298 K. The temperature dependence of two absorption features of the argon hydrogen chloride complex, at 2887 and 2879 wavelength/cm, leads to a bond energy estimate that depends on the assumptions made about the internal degrees of freedom of the complex. It is shown that agreement with experiment can be reached for well depths near 1.2 kcal/mole. This result is relatively insensitive to the choice of the vibrational frequencies and anharmonicities, but does depend on the extent to which the energy level manifolds are truncated to avoid molecular excitation in excess of the bond energy. The bond energy is found to deviate from the commonly accepted value of 0.4 kcal/mole. Possible causes for the discrepancy are considered.

Miziolek, A. W.↗

Effect of thermal exposure on lubricating properties of polyimide films and polyimide-bonded graphite fluoride films

The effect of thermal exposure on the weight loss, adherence, friction, and wear properties of polyimide films and polyimide bonded graphite fluoride films was investigated. Films bonded to 304 stainless steel or 440C-HT steel were thermally exposed at temperatures of 315 ,345, 370, or 400 C for 100 hours or more and then evaluated, using a pin-on-disk machine, at temperatures of 25, 315, or 345 C in atmospheres of dry or moist air. Polyimide films were brittle after thermal exposure. Polyimide bonded graphite fluoride films had adherence and gave low friction and wear results; thus, they appear to be good candidates for solid lubrication applications where long thermal soaks are prevalent.

Fusaro, R. L.↗

Adhesive bonding of ion beam textured metals and fluoropolymers

An electron bombardment argon ion source was used to ion etch various metals and fluoropolymers. The metal and fluoropolymers were exposed to (0.5 to 1.0) keV Ar ions at ion current densities of (0.2 to 1.5) mA/sq cm for various exposure times. The resulting surface texture is in the form of needles or spires whose vertical dimensions may range from tenths to hundreds of micrometers, depending on the selection of beam energy, ion current density, and etch time. The bonding of textured surfaces is accomplished by ion beam texturing mating pieces of either metals or fluoropolymers and applying a bonding agent which wets in and around the microscopic cone-like structures. After bonding, both tensile and shear strength measurements were made on the samples. Also tested, for comparison's sake, were untextured and chemically etched fluoropolymers. The results of these measurements are presented.

Mirtich, M. J.↗

Effect of thermal aging on the tribological properties of polyimide films and polyimide-bonded graphite fluoride films

Weight loss, adherence, friction and wear of polyimide films and polyimide-bonded graphite fluoride films applied to stainless steel disks and to 304 stainless steel thin foils were studied. The films were exposed at temperatures of 315 D, 345 D, 370 D, or 400 C for 100 hours or more and then evaluated at temperatures of 25 D, 315 D, or 345 C in atmospheres of dry or moist air. Polyimide films were found to be brittle after thermal exposure; but polyimide-bonded graphite fluoride possessed good adherence and gave low friction and wear results. Polyimide-bonded graphite fluoride films appear to be good candidates for solid lubrication applications where long thermal soaks are prevalent.

Fusaro, R. L.↗

Adhesives for bonding RSI tile to GrPI structure for advanced space transportation systems

A system was developed for bonding RSI tiles to a graphite/polymide composite substrate which would withstand the full range of environmental conditions. The bonding system, designated RA59, consists of a mixture of glass (sesquisiloxane) resin in RTV 560 silicone. A significant number of data points for the RA59 are in the 65-psi failure range both when tested, and after exposure to 700 F. This is over two times the best shear and tensile values obtained with RV60 at this temperature. It is concluded that with a thorough understanding of the critical parameters involved, the higher values should be obtained consistently with the RA59. This is of particular significance if higher strength tiles were to be used in a hard-bonded configuration.

Smith, K. E.↗

Bonding of sapphire to sapphire by eutectic mixture of aluminum oxide and zirconium oxide

An element comprising sapphire, ruby or blue sapphire can be bonded to another element of such material with a eutectic mixture of aluminum oxide and zirconium oxide. The bonding mixture may be applied in the form of a distilled water slurry or by electron beam vapor deposition. In one embodiment the eutectic is formed in situ by applying a layer of zirconium oxide and then heating the assembly to a temperature above the eutectic temperature and below the melting point of the material from which the elements are formed. The formation of a sapphire rubidium maser cell utilizing eutectic bonding is shown.

Deluca, J. J.↗

Adhesive bonding of ion beam textured metals and fluoropolymers

An electron-bombardment argon ion source was used to ion-etch various metals and fluoropolymers. The metal and fluoropolymers were exposed to (0.5 to 1.0)-keV Ar ions at ion current densities of 0.2 to 1.5 mA/sq cm for various exposure times. The resulting surface texture is in the form of needles or spires whose vertical dimensions may range from tenths to hundreds of micrometers, depending on the selection of beam energy, ion current density, and etch time. The bonding of textured surfaces is accomplished by ion-beam texturing mating pieces of either metals or fluoropolymers and applying a bonding agent which wets in and around the microscopic conelike structures. After bonding, both tensile and shear strength measurements were made on the samples. Also tested, for comparison's sake, were untextured and chemically etched fluoropolymers. The results of these measurements are presented in this paper.

Mirtich, M. J.↗

Ion-beam etching enhances adhesive bonding

Metals and fluoropolymers exposed to 0.5 to 1.0 keV argon ions at current densities of 0.2 to 1.5 mA/sq cm develop surface texturing that increases tensile and shear strength of epoxy bonds. Bonds are 46 to 100 percent stronger than those of chemically etched surfaces. Metals require 3 to 4 hours of bombardment to become properly textured. Fluoropolymers require 5 seconds to 30 minutes. Ion beam will not texture nickel. Unlike chemical treatments, bonding of fluoropolymers can be done days or months after ion treatment.

Banks, B. A.↗

Mechanisms of lubrication and wear of a bonded solid lubricant film

To obtain a better understanding of how bonded solid lubricant films lubricate and wear (in general), the tribological properties of polyimide-bonded graphite fluoride films were studied (in specific). A pin-on-disk type of testing apparatus was used; but in addition to sliding a hemispherically tipped rider, a rider with a 0.95 mm diameter flat area was slid against the film. This was done so that a lower, less variable contact stress could be achieved. Two stages of lubrication occurred. In the first, the film supported the load. The lubricating mechanism consisted of the shear of a thin surface layer (of the film) between the rider and the bulk of the film. The second occurred after the bonded film had worn to the substrate, and consisted of the shear of very thin lubricant films between the rider and flat plateaus generated on the metallic substrate asperities. The film wear mechanism was strongly dependent on contact stress.

Fusaro, R. L.↗

Improved bond coatings for use with thermal barrier coatings

The potential for improving the durability of thermal barrier coatings (TBC's) being developed for coal derived fuel fired gas turbines was studied. Furnace oxidation behavior of plasma deposited bond coatings was improved by increasing the thickness from 0.010 cm to 0.015 cm and by depositing the coatings at 20 kW with argon 3.5 vol % hydrogen arc gas rather than at 11 kW with argon. The most oxidation resistant plasma deposited bond coatings were Ni-14, 1Cr-13.4Al-0.10Zr, Ni-14.3Cr-14.4Al.0.16Y, and Ni-15.8Cr-12.8Al-0.36Y on B-1900 + Hf and Ni-30.9Cr-11.1Al-0.48Y on MAR-M-509. The oxidation resistant bond coatings improved TBC life when the coatings were deposited on the specimens supported on a nail bed fixture during coating.

Gedwill, M. A.↗

Effect of thermal aging on the tribological properties of polyimide films and polyimide-bonded graphite fluoride films

The effect of thermal aging on the weight loss, adherence, friction and wear of polyimide films and polyimide-bonded graphite fluoride films applied to 440C-HT stainless steel disks and to 304 stainless steel thin foils was studied. The films were exposed at temperatures of 315, 345, 370 or 400 C for 100 hours or more and then evaluated at temperatures of 25, 315 or 345 C in atmospheres of dry or moist air. Polyimide films were found to be brittle after thermal exposure; but polyimide-bonded graphite fluoride films possessed good adherence and gave low friction and wear results. Thus, polyimide-bonded graphite fluoride films appear to be good candidates for solid lubrication applications where long thermal soaks are prevalent.

Fusaro, R. L.↗

Enhancement of peptide bond formation by polyribonucleotides on clay surfaces in fluctuating environments

The selective effects of polyribonucleotides on the formation of glycine peptide bonds in glycine on clay surfaces are investigated as a model for a template mechanism for the effects of polynucleotides on peptide bond formation. Free oligoglycine yields were determined for the cycling reaction of glycine in the presence and absence of clay and polyribonucleotides or polydeoxyribonucleotides. The polyribonucleotides are observed to lead to increases of up to fourfold increases in oligoglycine formed, with greater enhancements for poly-G nucleotides than for poly-A, poly-U and poly-C, indicating a codonic bias. Polydeoxyribonucleotides are found to provide no enhancement in peptide formation rates, and yields were also greatly reduced in the absence of clay. A mechanism for peptide synthesis is proposed which involves the activation of glycine on the clay surface, followed by the formation of esters between glycine and the 2-prime OH groups of the polyribonucleotide and peptide bonds between adjacent amino acyl esters. It is pointed out that if this mechanism is correct, it may provide a basis for a direct template translation process, which would produce a singlet genetic code.

White, D. H.↗

A model for the acoustic impedance of linear suppressor materials bonded on perforated plate

An analytical model is developed for the acoustic impedance of a composite made of a fine screen bonded to a perforated plate, the resistance having been modeled using steady flow theory and data, and including both linear and nonlinear components. The model of the screen resistance alone is derived first, and it is then extended to include a perforated plate bonded to the screen. Quantities such as effective open ratio and pressure recovery are evaluated. Conclusions are presented, including: (1) when the screen is bonded to a perforated plate, the linear resistance increases as the inverse of the perforate open area, (2) the nonlinearity in the screen resistance depends on the square of the screen wire diameter, and (3) when the resistance is considered as a function of approach velocity, the screen nonlinear term increases as the inverse of the square of the perforated plate open area ratio. The general theory can be applied to any screen structure, but final results are limited to a twilled square weave screen. Results can be applied to the study of sound absorbing materials used for lining the walls of aircraft engine duct suppressors.

Rice, E. J.↗

Develop, demonstrate, and verify large area composite structural bonding with polyimide adhesives

The technology required to produce graphite-polyimide structural components with operational capability at 598 K (600 F) is considered. A series of polyimide adhesives was screened for mechanical and physical properties and processibility in fabricating large midplane bonded panels and honeycomb sandwich panels in an effort to fabricate a structural test component of the space shuttle aft body flap. From 41 formulations, LaRC-13, FM34B-18, and a modified LaRC-13 adhesive were selected for further evaluation. The LaRC-13 adhesive was rated as the best of the three adhesives in terms of availability, cost, processibility, properties, and ability to produce void fee large area (12" x 12") midplane bonds. Surface treatments and primers for the adhesives were evaluated and processes were developed for the fabrication of honeycomb sandwich panels of very good quality which was evidenced by rupture in the honeycomb core rather than in the facesheet bands on flatwise tensile strength testing. The fabrication of the adhesively bonded honeycomb sandwich cover panels, ribs, and leading edge covers of Celion graphite/LARC-160 polyimide laminates is described.

Bhombal, B. D.↗

Test and analysis of Celion 3000/PMR-15, graphite/polyimide bonded composite joints: Data report

Standard single lap, double lap and symmetric step lap bonded joints of Celion 3000/PMR-15 graphite/polyimide composite were evaluated. Composite to composite and composite to titanium joints were tested at 116 K (-250 F), 294 K (70 F) and 561 K (550 F). Joint parameters evaluated are lap length, adherend thickness, adherend axial stiffness, lamina stacking sequence and adherend tapering. Advanced joint concepts were examined to establish the change in performance of preformed adherends, scalloped adherends and hybrid systems. The material properties of the high temperature adhesive, designated A7F, used for bonding were established. The bonded joint tests resulted in interlaminar shear or peel failures of the composite and there were very few adhesive failures. Average test results agree with expected performance trends for the various test parameters. Results of finite element analyses and of test/analysis correlations are also presented.

Cushman, J. B.↗

Test and analysis of Celion 3000/PMR-15, graphite/polyimide bonded composite joints: Summary

Standard single lap, double lap and symmetric step lap bonded joints of Celion 3000/PMR-15 graphite/polyimide composite were evaluated. Composite to composite and composite to titanium joints were tested at 116K (-250 F), 294K (70 F) and 561K (550 F). Joint parameters evaluated were lap length, adherend thickness, adherend axial stiffness, lamina stacking sequence and adherend tapering. Tests of advanced joint concepts were also conducted to establish the change in performance of preformed adherends, scalloped adherends and hybrid systems. Special tests were conducted to establish material properties of the high temperature adhesive, designated A7F, used for bonding. Most of the bonded joint tests resulted in interlaminar shear or peel failures of the composite. There were very few adhesive failures. Average test results agree with expected performance trends for the various test parameters. Results of finite element analyses and of test/analysis correlations are also presented.

Cushman, J. B.↗