SEARCH · Engineering Papers

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Direct simulation Monte Carlo technique for modeling of the environment in the vicinity of the Space Shuttle Orbiter

A program for analyzing the flowfield parameters in the neighborhood of the Space Shuttle Orbiter has been developed. The program uses the direct simulation Monte Carlo method, which is a completely probabilistic Monte Carlo technique capable of analyzing 3-dimensional steady or unsteady flow with prescribed internal and external boundary conditions. The freestream flux densities incident on the external flowfield boundaries are calculated from the drifting Maxwellian gas properties of the freestream. The flux entering the flowfield from the internal boundary is calculated from the outgassing flux density distribution over the Shuttle external surface and the prescribed discrete source fluxes. This technique produces a numerical flowfield solution which is the probabilistic equivalent of a complete solution of the time-dependent, 3-dimensional Boltzmann equation. Flowfield results are presented for the following configurations: (1) Shuttle angles of attack of 0 and 90 deg, (2) freestream density 10 to the 9th - 10 to the 11th per cu cm, (3) Shuttle outgassing flux density, and (4) operation of the aft downfiring vernier Reaction Control System (RCS) engine. Results are presented for column density distribution of outgassed and engine species and for the flux density of outgassed and engine species incident on the Shuttle bay and the windshield.

Melfi, L. T., Jr.↗

NASA NTRS1986

Comparison of computations and experimental data for leading edge vortices - Effects of yaw and vortex flaps

Computations are presented using the conical Euler equations for swept delta wings with leading edge vortices. All the wings have sharp leading edges swept at 75 degrees to the freestream. In addition to an idealized flat plate model, geometrical features also included are thickness, centerbody, and two vortex flaps. Freestream Mach numbers of 1.7 to 2.8, angles of attack of 10 and 12 degrees, and angles of yaw of 0 and 8 degrees are considered. The computations are compared with pitot pressure traverses for one case. Other calculations are compared with pitot pressure traverses for one case. Other calculations are compared with surface pressure data and vapor screen pictures recently obtained at NASA Langley Research Center. The comparisons indicate that the dominant features of these flows are adequately modeled by the Euler equations, but viscous models are needed for the surface boundary layer and secondary separations.

Murman, E. M.↗

NASA NTRS1987

Flow visualization model of the leeside flows over conically cambered delta wings at supersonic speeds

Surface pressure, flow visualization, and force-and-moment data have been obtained for four, variously conically-cambered delta wing models in a range of flow conditions, with a view to leeside flow mechanisms. The influences exerted by Mach number, angle-of-attack, and camber are determined. An analysis of photographic data leads to the analysis of 12 distinctive leeside flow types, which are further categorizable into two groups respectively possessing either one or two dominant features in the leeside flow field: in the former, either the leading edge or hinge line are the originators of the dominant feature; in the latter, both the leading edge and hinge line are generators.

Wood, Richard M.↗

NASA NTRS1992

Tests Of Array Of Flush Pressure Sensors

Report describes tests of array of pressure sensors connected to small orifices flush with surface of 1/7-scale model of F-14 airplane in wind tunnel. Part of effort to determine whether pressure parameters consisting of various sums, differences, and ratios of measured pressures used to compute accurately free-stream values of stagnation pressure, static pressure, angle of attack, angle of sideslip, and mach number. Such arrays of sensors and associated processing circuitry integrated into advanced aircraft as parts of flight-monitoring and -controlling systems.

Larson, Larry J.↗

NASA NTRS1992

Pitot survey of exhaust flow field of a 2-D scramjet nozzle at Mach 6 with air or freon and argon used for exhaust simulation

A pitot-rake survey of the simulated exhaust of a half-span scramjet nozzle model was conducted in the Langley 20-Inch Mach 6 Tunnel to provide an additional data set for computational fluid dynamics (CFD) code comparisons. A wind-tunnel model was tested with a 26-tube pitot rake that could be manually positioned along the mid-semispan plane of the model. The model configuration had an external expansion surface of 20 degrees and an internal cowl expansion of 12 degrees; tests were also performed with a flow fence. Tests were conducted at a free-stream Reynolds number of approximately 6.5 x 10(exp 6) per foot and a model angle of attack of -0.75 degrees. The two exhaust gas mediums that were tested were air and a Freon 12-argon mixture. Each medium was tested at two jet total pressures at approximately 28 and 14 psia. This document presents the flow-field survey results in graphical as well as tabular form, and several observations concerning the results are discussed. The surveys reveal the major expected flow-field characteristics for each test configuration. For a 50-percent freon 12 and 50-percent argon mixture by volume (Fr-Ar), the exhaust jet pressures were slightly higher than those for air. The addition of a flow fence slightly raised the pitot pressure for the Fr-Ar mixture, but it produced little change for air. For the Fr-Ar exhaust, the plume was larger and the region between the shock wave and plume was smaller.

Monta, William J.↗

NASA NTRS1939

A simplified method for the calculation of airfoil pressure distribution

A method is presented for the rapid calculation of the pressure distribution over an airfoil section when the normal-force distribution and the pressure distribution over the "base profile" (i.e., the profile of the same airfoil were the camber line straight and the resulting airfoil at zero angle of attack) are known. This note is intended as a supplement to N.A.C.A. Report Nos. 631 and 634 wherein methods are presented for the calculation of the normal-force distribution over plain and flapped airfoils, respectively, but not of the pressures on the individual surfaces. Base-profile pressure-coefficient distributions for the usual N.A.C.A. family of airfoils, which are also suitable for several other commonly employed airfoils, are included in tabular form. With these tabulated base-profile pressures and the computed normal-force distributions, pressure distributions adequate for most engineering purposes can be obtained.

Allen, H Julian↗

NASA NTRS1995

A parametric study of supersonic laminar flow for swept wings using linear stability analysis

A parametric study to predict the extent of laminar flow on the upper surface of a generic swept-back wing (NACA 64A010 airfoil section) at supersonic speeds was conducted. The results were obtained by using surface pressure predictions from an Euler/Navier-Stokes computational fluid dynamics code coupled with a boundary layer code, which predicts detailed boundary layer profiles, and finally with a linear stability code to determine the extent of laminar flow. The parameters addressed are Reynolds number, angle of attack, and leading-edge wing sweep. The results of this study show that an increase in angle of attack, for specific Reynolds numbers, can actually delay transition. Therefore, higher lift capability, caused by the increased angle of attack, as well as a reduction in viscous drag due to the delay in transition is possible for certain flight conditions.

Cummings, Russell M.↗

NASA NTRS1996

Surface-Pressure and Flow-Visualization Data at Mach Number of 1.60 for Three 65 deg Delta Wings Varying in Leading-Edge Radius and Camber

An experimental investigation of the effect of leading-edge radius, camber, Reynolds number, and boundary-layer state on the incipient separation of a delta wing at supersonic speeds was conducted at the Langley Unitary Plan Wind Tunnel at Mach number of 1.60 over a free-stream Reynolds number range of 1 x 106 to 5 x 106 ft-1. The three delta wing models examined had a 65 deg swept leading edge and varied in cross-sectional shape: a sharp wedge, a 20:1 ellipse, and a 20:1 ellipse with a -9.750 circular camber imposed across the span. The wings were tested with and without transition grit applied. Surface-pressure coefficient data and flow-visualization data indicated that by rounding the wing leading edge or cambering the wing in the spanwise direction, the onset of leading-edge separation on a delta wing can be raised to a higher angle of attack than that observed on a sharp-edged delta wing. The data also showed that the onset of leading-edge separation can be raised to a higher angle of attack by forcing boundary-layer transition to occur closer to the wing leading edge by the application of grit or the increase in free-stream Reynolds number.

McMillin, S. Naomi↗

NASA NTRS1999

Changes in the Optical Properties of Materials Are Observed After 18 Months in Low Earth Orbit

Materials located on the exterior of spacecraft in low Earth orbit are subjected to a number of environmental threats, including atomic oxygen, ultraviolet radiation, thermal cycling, and micrometeroid and debris impact. Atomic oxygen attacks materials vulnerable to oxidation. Ultraviolet radiation can break chemical bonds and cause undesirable changes in optical properties. Thermal cycling can cause cracking, and micrometeroid and debris impacts can damage protective coatings. Another threat is contamination. The outgassing of volatile chemicals can contaminate nearby surfaces, changing their thermal control properties. Contaminated surfaces may undergo further change as a result of atomic oxygen and ultraviolet radiation exposure. The Passive Optical Sample Assembly (POSA) experiment was designed as a risk mitigation experiment for the International Space Station. Samples were characterized before launch, exposed for 18 months on the exterior of Mir, and characterized upon their return. Lessons learned from POSA about the durability of material properties can be applied to the space station and other long-duration missions.

Jaworske, Donald A.↗

NASA NTRS2006

Development of a Boundary Layer Property Interpolation Tool in Support of Orbiter Return To Flight

A new tool was developed to predict the boundary layer quantities required by several physics-based predictive/analytic methods that assess damaged Orbiter tile. This new tool, the Boundary Layer Property Prediction (BLPROP) tool, supplies boundary layer values used in correlations that determine boundary layer transition onset and surface heating-rate augmentation/attenuation factors inside tile gouges (i.e. cavities). BLPROP interpolates through a database of computed solutions and provides boundary layer and wall data (delta, theta, Re(sub theta)/M(sub e), Re(sub theta)/M(sub e), Re(sub theta), P(sub w), and q(sub w)) based on user input surface location and free stream conditions. Surface locations are limited to the Orbiter s windward surface. Constructed using predictions from an inviscid w/boundary-layer method and benchmark viscous CFD, the computed database covers the hypersonic continuum flight regime based on two reference flight trajectories. First-order one-dimensional Lagrange interpolation accounts for Mach number and angle-of-attack variations, whereas non-dimensional normalization accounts for differences between the reference and input Reynolds number. Employing the same computational methods used to construct the database, solutions at other trajectory points taken from previous STS flights were computed: these results validate the BLPROP algorithm. Percentage differences between interpolated and computed values are presented and are used to establish the level of uncertainty of the new tool.

Greene, Francis A.↗

NASA NTRS2019

Measurement and Analysis of Terminal Shock Oscillation and Buffet Forcing Functions on a Launch Vehicle Payload Fairing

The buffet loads on a launch vehicle payload shroud can be impacted by the unsteadiness associated with a terminal shock at high subsonic speeds. At these conditions, flow accelerates to supersonic speeds on the nose of the payload fairing and is terminated by a normal shock on the cylindrical section downstream of the nose cone/cylinder shoulder. The location of the terminal shock and associated separated boundary layer is affected by the freestream Mach number, Reynolds number, and the pitch/yaw of the launch vehicle. Furthermore, even when the freestream conditions and vehicle attitude are constant, this terminal shock oscillates on the surface of the vehicle. The time-varying surface pressure associated with the terminal shock results in unsteady aerodynamic loads that may interact with vehicle structural dynamic modes and the guidance and control of the vehicle. Buffet testing of a 3-percent scale rigid buffet model of a launch vehicle cargo configuration with a tangent-ogive payload shroud was conducted in 2012 and in 2016. Initial buffet forcing functions (BFFs) utilized a coarse pressure sensor distribution on the vehicle surface in which a single longitudinal station with eight sensors observed the terminal shock environment at Mach 0.90. An examination of these circumferential pressures reveal large impulse-like pressure fluctuations and an asymmetry in pressure when the vehicle is at a nonzeroangle of attack that result in high BFFs. Revisions to the shock integration region were made based on computational fluid dynamics and shadowgraph video of shock motion to better represent the BFFs and reduce the high loads resulting from this environment. To more clearly understand this terminal shock environment, a second wind tunnel test was conducted with a dense distribution of 256 sensors at the terminal shock location. These sensor arrays presents a unique opportunity to observe the unsteady terminal shock environment and to characterize the impact of various integration schemes on the BFFs. This paper presents a summary of the development of BFFs for this terminal shock and a detailed analyses of shock region pressure coefficients, coherence, BFFs, shock location time histories, and power spectral density to help guide development of BFFs for other launch vehicle test and analysis programs.

Piatak, David J.↗

NASA NTRSDate not supplied

A Design Exploration of Natural Laminar Flow Applications for the SUSAN Electrofan Concept

A trade study supported by the NASA Convergent Aeronautics Solutions (CAS) Project is presently underway to explore the desirability, feasibility, and viability of a new vehicle concept. The vehicle under development is the SUbsonic Single Aft eNgine (SUSAN) Electrofan configuration, which is a subsonic regional jet with the transformative concept of combining wing-mounted distributed electrified aircraft propulsion with a single engine design. The multidisciplinary team is investigating several potential technologies that would help the SUSAN Electrofan configuration achieve its performance goals, one of which is the application of Natural Laminar Flow (NLF) to the main wing. The present computational study utilizes the Crossflow Attenuated Natural Laminar Flow (CATNLF) design method to reshape the wing airfoils to obtain significant extents of NLF at the cruise condition. Fully-turbulent and laminar designs were performed to quantify the aerodynamic performance potential of NLF on the SUSAN Electrofan configuration. The laminar design supported laminar flow on53% of the area of the wing upper surface, resulting in a 19count (8.8%) drag reduction for the wing-fuselage configuration. The near-cruise off-design characteristics are also studied and illustrate that the robust laminar design sustains an NLF performance benefit through perturbations in Mach and angle of attack. A discussion is also included on multidisciplinary implications of utilizing NLF for the configuration, including design, manufacturing, and operational considerations required to support NLF on the main wing, as well as the interaction between the potential wing-mounted boundary layer ingestion technology that is also being explored for the SUSAN Electrofan configuration.

Natural Laminar Flow↗

NASA NTRS2022

Vacuum Melt Infiltration of 2D Tyranno SA3® Ceramic Matrix Composites with Cr-25(wt.%)Si Intermetallic Alloy

The potential and limitations of vacuum melt infiltrating woven preforms of 2D Tyranno SA3 fibers with Cr-25(wt.%)Si alloy were investigated. Microstructural observations revealed that the volume fractions of open voids infiltrated by the molten metal varied between 3.7 and 10.0% irrespective of the magnitudes of the melt infiltration temperatures and hold times, which was attributed in part to substantial volatilization of the silicide charge based on computational thermodynamics. In the absence of experimental data, poor wettability of the melt could not be ruled out unambiguously. Other possible reasons are carefully examined and discarded. Ring microstructures were observed around the fibers mainly at the outer surfaces of the infiltrated preform, where the BN and chemical vapor infiltrated SiC coatings had vaporized in the high vacuum environment. In contrast, they were absent in the interior of the preform, where the coatings were still present with no evidence of molten metal attack of the coatings. Details of thermodynamic calculations are presented to confirm the volatilization of the BN and CVI SiC coatings thereby resulting in the ring microstructures due to the filling of voids by the molten silicide. It is concluded that successful melt infiltration of Tyranno SA3® with Cr-25%Si can be only achieved under sufficient positive pressure to prevent volatilization of the coatings and the molten silicide.

Cr-25%Si↗

NASA NTRSDate not supplied

Transonic Cruise Slotted Wing Design for Commercial Transport Aircraft using CDISC

A knowledge-based aerodynamic design method, CDISC, has been extended to enable the computational design of transonic cruise slotted wings for commercial transport aircraft. The cruise slotted wing is a multielement wing concept with a forward main element and an aft flap element, separated to form an intermediate slot. This slot favorably redirects airflow from the main element lower surface toward the low-momentum, upper-surface boundary layer of the flap. Relative to the supercritical wing, the cruise slotted wing enables greater aft loading that helps to reduce shock strength and transonic pressure drag. The cruise slotted wing may be considered a passive drag-reduction technology with potential fuel burn savings and increased vehicle range for next-generation aircraft. The current paper seeks to quantify the drag-saving benefits of cruise slotted wing technology in application to single-aisle commercial transport aircraft. A series of multielement design constraints were developed within CDISC for the design of a partial-span, cruise slotted wing for a Mach-0.8 variant of the Common Research Model. To mitigate the skin-friction drag penalty associated with cruise slotted wings, the design features a flap with natural laminar flow over approximately 75% of the flap surface area. Cruise drag estimates from the NASA USM3D flow solver between a supercritical wing and the partial-span, cruise slotted wing design were within one drag count. Near-cruise, off-design analyses showed limited laminar flow sensitivity to angle of attack and a more gradual drag rise compared to a supercritical wing. Based on this demonstrated benefit, future work is motivated to design a cruise slotted wing with natural laminar flow on both wing elements to achieve a significant reduction in cruise drag while providing delayed drag divergence.

CDISC↗

NASA NTRSDate not supplied

Automatic Boundary-Layer Adaptation of Structured Grids in VULCAN-CFD

In supersonic and hypersonic flow computations, well-resolved boundary layers are essential for accurate quantification of surface heating and transition prediction, particularly via linear stability analysis. Grid design for hypersonic flows with shocks, boundary-layer separation, and/or complex mean flow features incorporating spanwise/azimuthal inhomogeneities is a difficult issue. In comparison to a manual grid adaptation procedure, an autonomous grid adaptation technique offers significant improvements in computing time and solution quality. The VULCAN-CFD solver already includes a validated procedure for automatic adaption of structured grids to the bow shock. The present focus is on implementing an automatic boundary-layer adaptation capability in VULCAN-CFD that adapts structured, multiblock grids to both the bow shock and the boundary layer at the same time. The boundary-layer adaptation algorithm allows the user to specify the number of cells within the boundary layer, along with the input parameters used for detecting the edge of the boundary layer, namely, the variable used in the edge detection criterion,the edge detection method, the detection direction, and the relaxation factor used during the morphing of the grid. The algorithm automatically distributes grid points along the wall-normal direction to achieve a smooth variation in grid spacing from the edge of the boundary layer to a"junction" location within the outer part of the grid. Illustrative results are presented for three different high-speed configurations: the two-dimensional flow over a cylinder at Mach 17.6 and unit Reynolds number of Re=0.38x10^6 m^-1, the axisymmetric flow over a cone-cylinder-flare model at Mach 6.0 and Re = 10.5×10^6 m^-1, and the three-dimensional flow over a blunt, 7-degree half-angle cone at 5-degree angle of attack in a Mach 9.79 flow with Re = 17.1×10^6 m^-1. The automated boundary-layer adaptation is shown to provide an adequate grid topology that is aligned with the bow shock in the outer part of the grid and also resolves the viscous boundary-layer region close to the surface.

boundary layer transition↗

NASA NTRS1972

Space shuttle: Static aerodynamic characteristics of the MSC-040A the Msc-040A space shuttle orbiter with wedge centerline vertical and twin vertical tails at Mach numbers from 0.6 to 4.96

The results are presented from experimental aerodynamic investigations conducted on a 0.6-percent scale model of the MSC-040 space shuttle orbiter in a 14 inch trisonic wind tunnel. The purpose of the test program was to define the stability, control, and performance characteristics of the baseline MSC-040A orbiter configuration with proposed alternate wing pods, with several vertical tail configurations with and without flared rudders, and with upper wing surface flap deflections. Force and moment data and model base and balance cavity pressure data were obtained for a Mach range of 0.60 through 4.96 and dynamic pressure range of 465 through 1580 psf. Model attitude was varied from 0 to +34 degrees angle of attack at zero sideslip and -4 to +10 degrees angle of sideslip at 0, 10, 20, and 24 degrees angle of attack.

Glass, K. J.↗

NASA NTRS1977

Transonic aerodynamic characteristics of a supercritical-wing transport model with trailing-edge controls

The effects of wing trailing-edge control surfaces on the static transonic aerodynamic characteristics of a transport configuration with a supercritical wing were studied. The configuration was tested with both an area-ruled fuselage and a cylindrical fuselage. The Mach number range was from 0.80 to 0.96 and the angle of attack range was from -1 deg to 12 deg. The Reynolds number was 1,580,000 based on the mean aerodynamic chord. Tabular data are presented.

Mann, M. J.↗

NASA NTRS1981

Flight experiments with a slender cone at angle of attack

The three-dimensional leeward separation about a 5 deg semi-angle cone at an 11 deg angle of attack was investigated in flight, in the wind tunnel, and by numerical computations. The test conditions were Mach numbers of 0.6, 1.5, and 1.8 at Reynolds numbers between 7 and 10 million based on free-stream conditions and a 30-inch wetted length or surface. The surface conditions measured included mean static and fluctuating pressures; skin friction magnitudes and separation line positions were obtained using obstacle blocks. The mean static pressures from flight and wind tunnel were in good agreement. The computed results gave the same distributions, but were slightly more positive in magnitude. The experimentally measured primary and secondary separation line locations compared closely with computed results. There were substantial differences in level and in trend between the surface root-mean-square pressure fluctuations obtained in flight and in the wind tunnel, due, it is thought, to a relatively high acoustic disturbance level in the tunnel compared with the quiescent conditions in flight.

Peake, D. J.↗