Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WIRE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Rotating hot-wire investigation of the vortex responsible for blade-vortex interaction noise

This distribution of the circumferential velocity of the vortex responsible for blade-vortex interaction noise was measured using a rotating hot-wire rake synchronously meshed with a model helicopter rotor at the blade passage frequency. Simultaneous far-field acoustic data and blade differential pressure measurements were obtained. Results show that the shape of the measured far-field acoustic blade-vortex interaction signature depends on the blade-vortex interaction geometry. The experimental results are compared with the Widnall-Wolf model for blade-vortex interaction noise.

Fontana, Richard Remo↗
NASA NTRS1989

Wiring Viterbi decoders (splitting deBruijn graphs)

A new Viterbi decoder, capable of decoding convolutional codes with constraint lengths up to 15, is under development for the Deep Space Network (DSN). A key feature of this decoder is a two-level partitioning of the Viterbi state diagram into identical subgraphs. The larger subgraphs correspond to circuit boards, while the smaller subgraphs correspond to Very Large Scale Integration (VLSI) chips. The full decoder is built from identical boards, which in turn are built from identical chips. The resulting system is modular and hierarchical. The decoder is easy to implement, test, and repair because it uses a single VLSI chip design and a single board design. The partitioning is completely general in the sense that an appropriate number of boards or chips may be wired together to implement a Viterbi decoder of any size greater than or equal to the size of the module.

Collins, O.↗
NASA NTRS1988

Turbulence measurements in shock induced flow using hot wire anemometry

Heat transfer measurements over various geometric shapes have been made by immersing models in shock-induced flows. The heat transfer to a body is strongly dependent on the turbulence level of the stream. The interpretation of such heat transfer measurements requires a knowledge of the turbulence intensity. Turbulence intensity measurements, using hot-wire anemometry, have been successfully carried out in shock-induced flows. The experimental procedures for making such measurements and the techniques required are discussed.

Hartung, Lin C.↗
NASA NTRS1989

Fabrication and testing of subminiature multi-sensor hot-wire probes

A method for the fabrication of hot-wire sensors measuring 0.6 micron in diameter and 200 microns in length is described. This method allows accurate control of sensing-element orientation, thus making it possible to produce multisensor probes. Test results obtained with a miniature sensor fabricated by this method, for the outer region of a turbulent boundary layer developing in a zero presure gradient were compared to measurements from a conventional-sized probe made in the same flow, demonstrating that, because of their improved spatial resolution, subminiature sensors can provide more accurate measurements in boundary layers than do the conventional probes.

Ligrani, P. M.↗
NASA NTRS1990

Impact Wire Dislodges Obstructions

Snakelike tool loosens trapped debris obstructing narrow passages in normally inaccessible locations. Flexible tool threaded into obstructed channel, much like common plumbing snake. Wire fed along inner tube of tool until tip reaches obstruction. Delivers impact from impact tool to obstruction. Designed for use in narrow, intricate coolant channels of rocket engine. Lends itself readily to modification for use in engine blocks, heat exchangers, general plumbing, and like.

Ricklefs, Steven K.↗
NASA NTRS1989

Development and characterization of PdCr temperature-compensated wire resistance strain gage

A temperature-compensated resistance static strain gage with potential to be used to 600 C was recently developed. Gages were fabricated from specially developed palladium-13 w/o chromium (Pd-13Cr) wire and platinum (Pt) compensator. When bonded to high temperature Hastelloy X, the apparent strain from room temperature to 600 C was within 400 microstrain for gages with no preheat treatment and within 3500 microstrain for gages with 16 hours prestabilization at 640 C. The apparent strain versus temperature relationship of stabilized PdCr gages were repeatable with the reproducibility within 100 microstrain during three thermal cycles to 600 C and an 11 hours soak at 600 C. The gage fabrication, construction and installation is described. Also, the coating system used for this compensated resistance strain gage is explained. The electrical properties of the strain sensing element and main characteristics of the compensated gage including apparent strain, drift and reproducibility are discussed.

Lei, Jih-Fen↗
NASA NTRS1989

Method of forming low cost, formable High T(subc) superconducting wire

A ceramic superconductivity part, such as a wire, is produced through the partial oxidation of a specially formulated copper alloy in a core. The alloys contains low level of quantities of rare earth and alkaline earth dopant elements. Upon oxidation at high temperatures, and superconducting oxide phases are formed as a thin film.

Smialek, James L.↗
NASA NTRS1989

Lightning flashes triggered in altitude by the rocket and wire technique

Electrical measurements were conducted in 1987 and 1988 on streamer and leader discharges occurring during the first stages of a triggered flash. This paper describes the pulsing phenomenon observed at positive leader onset (typical pulsing rate 25 microns), and it is shown that the same process happened in the case of the ignition of a flash triggered in altitude; with a wire several hundred meters long, positive leader propagates alone for several ms before the ignition of the downward negative stepped leader.

Laroche, P.↗
NASA NTRS1990

A rotating hot-wire technique for spatial sampling of disturbed and manipulated duct flows

A duct flow spatial sampling technique, in which an X-wire probe is rotated about the center of a cylindrical test section at a radius equal to one-half that of the test section in order to furnish nearly instantaneous multipoint measurements of the streamwise and azimuthal components, is presently evaluated in view of the control of flow disturbances downstream of various open inlet contractions. The effectiveness of a particular contraction in controlling ingested flow disturbances was ascertained by artificially introducing disturbances upstream of the contractions; control effectiveness if found to be strongly dependent on inlet contraction, with consequences for the reduction of passing-blade frequency noise during gas turbine engine ground testing.

Wark, C. E.↗
NASA NTRS1991

Reduced-Wiring Tactile Sensor

Proposed tactile sensor on robot finger puts out multiplexed analog signals transmitted to control computer on fewer wires than needed to transmit equivalent digital signals. Analog output represents data on contact area of object being gripped, on position of object, and on direction and rate of slippage if any. Consists of chains of normally open switches and resistors on surface of finger. Each resistance double preceding resistance in each chain. Constant-current sources supply power to chains.

Ohm, Timothy R.↗
NASA NTRS1991

Selection of wires and circuit protective devices for STS Orbiter vehicle payload electrical circuits

Electrical designers of Orbiter payloads face the challenge of determining proper circuit protection/wire size parameters to satisfy Orbiter engineering and safety requirements. This document is the result of a program undertaken to review test data from all available aerospace sources and perform additional testing to eliminate extrapolation errors. The resulting compilation of data was used to develop guidelines for the selection of wire sizes and circuit protection ratings. The purpose is to provide guidance to the engineering to ensure a design which meets Orbiter standards and which should be applicable to any aerospace design.

Gaston, Darilyn M.↗
NASA NTRS1991

Low cost, formable, high T(sub c) superconducting wire

A ceramic superconductivity part such as a wire is produced through the partial oxidation of a specially formulated copper alloy in the core. The alloys contain low level quantities of rare earth and alkaline earth dopant elements. Upon oxidation at high temperature, superconducting oxide phases are formed as a thin film.

Smialek, James L.↗
NASA NTRS1992

Mechanical Backup For Fly-By-Wire Control System

Mechanical device eliminates need for redundant fly-by-wire subsystems. Main components are two linkages. One connected to control column in conventional, reversible control system. Other slides inside first linkage and connected to pilot's control wheel. In addition to aircraft applications, design used in control systems in which computer control desirable but safety backup systems required; for example, in boat rudders, engine controls in boats and automobiles, and controls in construction equipment.

Stewart, Eric C.↗
NASA NTRS1992

Frequency Responses Of Hot-Wire Anemometers

Report describes theoretical study of frequency response of constant-temperature hot-wire anemometer, with view toward increasing frequency response while maintaining stable operation in supersonic flow. Effects of various circuit parameters discussed.

Watmuff, Jonathan H.↗
NASA NTRS1991

Fluctuation diagrams for hot-wire anemometry in subsonic compressible flows

The concept of using 'fluctuation diagrams' for describing basic fluctuations in compressible flows was reported by Kovasznay in the 1950's. The application of this technique, for the most part, was restricted to supersonic flows. Recently, Zinovev and Lebiga published reports where they considered the fluctuation diagrams in subsonic compressible flows. For the above studies, the velocity and density sensitivities of the heated wires were equal. However, there are considerable data, much taken in the 1950's, which indicate that under some conditions the velocity and density sensitivities are not equal in subsonic compressible flows. Therefore, possible fluctuation diagrams are described for the cases where the velocity and density sensitivities are equal and the more general cases where they are unequal.

Stainback, P. C.↗
NASA NTRS1992

Wiring for aerospace applications

In this paper, the authors summarize the current state of knowledge of arc propagation in aerospace power wiring and efforts by the National Aeronautics and Space Administration (NASA) towards the understanding of the arc tracking phenomena in space environments. Recommendations will be made for additional testing. A database of the performance of commonly used insulating materials will be developed to support the design of advanced high power missions, such as Space Station Freedom and Lunar/Mars Exploration.

Christian, J. L., Jr.↗
NASA NTRS1990

Cyclic hot firing results of tungsten-wire-reinforced, copper-lined thrust chambers

An advanced thrust liner material for potential long life reusable rocket engines is described. This liner material was produced with the intent of improving the reusable life of high pressure thrust chambers by strengthening the chamber in the hoop direction, thus avoiding the longitudinal cracking due to low cycle fatigue that is observed in conventional homogeneous copper chambers, but yet not reducing the high thermal conductivity that is essential when operating with high heat fluxes. The liner material produced was a tungsten wire reinforced copper composite. Incorporating this composite into two hydrogen-oxygen test rocket chambers was done so that its performance as a reusable liner material could be evaluated. Testing results showed that both chambers failed prematurely, but the crack sites were perpendicular to the normal direction of cracking indicating a degree of success in containing the tremendous thermal strain associated with high temperature rocket engines. The failures, in all cases, were associated with drilled instrumentation ports and no other damages or deformations were found elsewhere in the composite liners.

Kazaroff, John M.↗
NASA NTRS1991

A fine-wire thermocouple probe for measurement of stagnation temperatures in real gas hypersonic flows of nitrogen

A fine-wire thermocouple probe was used to determine freestream stagnation temperatures in hypersonic flows. Data were gathered in a N2 blowdown wind tunnel with runtimes of 1-5 s. Tests were made at supply pressures between 30 and 1400 atm and supply temperatures between 700 and 1900 K, with Mach numbers of 14 to 16. An iterative procedure requiring thermocouple data, pilot pressure measurements, and supply conditions was used to determine test cell stagnation temperatures. Probe conduction and radiation losses, as well as real gas behavior of N2, were accounted for during analysis. Temperature measurement error was found to be 5 to 10 percent. A correlation was drawn between thermocouple diameter Reynolds number and temperature recovery ratio. Transient probe behavior was studied and was found to be adequate in temperature gradients up to 1000 K/s.

Hollis, Brian R.↗