Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TIP SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Parametric evaluation of ducted fuel injection in an optically accessible mixing-controlled compression-ignition engine with two- and four-duct assemblies

Ducted fuel injection (DFI) is a strategy to improve fuel/charge-gas mixing in direct-injection compression-ignition engines. DFI involves injecting fuel along the axis of a small tube in the combustion chamber, which promotes the formation of locally leaner mixtures in the autoignition zone relative to conventional diesel combustion. Previous work has demonstrated that DFI is effective at curtailing engine-out soot emissions across a wide range of operating conditions. This study extends previous investigations, presenting engine-out emissions and efficiency trends between ducted two-orifice and ducted four-orifice injector tip configurations. For each configuration, parameters investigated include injection pressure, injection duration, intake manifold pressure, intake manifold temperature, start of combustion timing, and intake-oxygen mole fraction. For both configurations and across all parameters, DFI reduced engine-out soot emissions compared to conventional diesel combustion, with little effect on other emissions and engine efficiency. Emissions trends for both configurations were qualitatively the same across the parameters investigated. The four-duct configuration had higher thermal efficiency and indicated-specific engine-out nitrogen oxide emissions but lower indicated-specific engine-out hydrocarbon and carbon monoxide emissions than the two-duct assembly. Both configurations achieved indicated-specific engine-out emissions for both soot and nitrogen oxides that comply with current on- and off-road heavy-duty regulations in the United States without exhaust-gas aftertreatment at an intake-oxygen mole fraction of 12%. High-speed in-cylinder imaging of natural soot luminosity shows that some conditions include a second soot-production phase late in the cycle. The probability of these late-cycle events is sensitive to both the number of ducted sprays and the operating conditions.

Yraguen, Boni Frances↗
NASA NTRS2003

Investigation of Pneumatic Inlet and Diffuser Blowing on a Ducted Fan Propulsor in Static Thrust Operation

Tilting ducted fans present a solution for the lifting and forward flight propulsion requirements of VTOL aircraft. However, the geometry of the duct enshrouding the propeller has great a effect on the efficiency of the fan in various flight modes. Shroud geometry controls the velocity and pressure at the face of the fan, while maintaining a finite loading out at the tips of the fan blades. A duct tailored for most efficient generation of static lifting thrust will generally suffer from performance deficiencies in forward flight. The converse is true as well, leaving the designer with a difficult trade affecting the overall performance and sizing of the aircraft. Ideally, the shroud of a vertical lifting fan features a generous bell mouth inlet promoting acceleration of flow into the face of the fan, and terminating in a converging nozzle at the exit. Flow entering the inlet is accelerated into the fan by the circulation about the shroud, resulting in an overall increase in thrust compared to an open propeller operating under the same conditions . The accelerating shroud design is often employed in lifting ducted fans to benefit from the thrust augmentation; however, such shroud designs produce significant drag penalties in axial flight, thus are unsuitable for efficient forward flight applications. Decelerating, or diffusing, duct designs are employed for higher speed forward flight configurations. The lower circulation on the shroud tends to decelerate the flow into the face of the fan, which is detrimental to static thrust development; however, net thrust is developed on the shroud while the benefits of finite blade loading are retained. With judicious shroud design for intended flight speeds, a net increase in efficiency can be obtained over an open propeller. In this experiment, conducted under contract to NASA LaRC (contract NAG-1-02093) circulation control is being applied to a mildly diffusing shroud design, intended for improved forward flight performance, to generate circulation in the sense of an accelerating duct design. The intent is to improve static thrust performance of a ducted fan tailored for high speed axial flight, while at the same time significantly reduce the pressure signature on the ground plane. Circulation control on the fan shroud is achieved by the Coanda effect.

Kondor, Shayne↗
NASA NTRS2014

Evaluation of the New Version of the Laser-Optical Disdrometer, OTT Parsivel2

A comparative study of raindrop size distribution measurements has been conducted at NASA's Goddard Space Flight Center where the focus was to evaluate the performance of the upgraded laser-optical OTT Particle Size Velocity (Parsivel2; P2) disdrometer. The experimental setup included a collocated pair of tipping-bucket rain gauges, OTT Parsivel (P1) and P2 disdrometers, and Joss-Waldvogel (JW) disdrometers. Excellent agreement between the two collocated rain gauges enabled their use as a relative reference for event rain totals. A comparison of event total showed that the P2 had a 6%absolute bias with respect to the reference gauges, considerably lower than the P1 and JW disdrometers. Good agreement was also evident between the JW and P2 in hourly raindrop spectra for drop diameters between 0.5 and 4 mm. The P2 drop concentrations mostly increased toward small sizes, and the peak concentrations were mostly observed in the first three measurable size bins. The P1, on the other hand, underestimated small drops and overestimated the large drops, particularly in heavy rain rates. From the analysis performed, it appears that the P2 is an improvement over the P1 model for both drop size and rainfall measurements. P2 mean fall velocities follow accepted terminal fall speed relationships at drop sizes less than 1 mm. As a caveat, the P2 had approximately 1ms21 slower mean fall speed with respect to the terminal fall speed near 1 mm, and the difference between the mean measured and terminal fall speeds reduced with increasing drop size. This caveat was recognized as a software bug by the manufacturer and is currently being investigated.

disdrometers↗
DOE OSTI2019

Spray characterization for engine combustion network Spray G injector using high-fidelity simulation with detailed injector geometry

This article presents a computational fluid dynamics study of the engine combustion network Spray G, focusing on the transient characteristics of the spray during the start of injection and the impacts of nozzle geometry details derived from the manufacturing process. The large-eddy-simulation method, coupled with the volume-of-fluid method, was used to model the high-speed turbulent two-phase flow. A moving-needle boundary condition was applied to capture the internal flow boundary condition accurately. The injector geometry was measured with micron-level resolution using X-ray tomographic imaging at the Advanced Photon Source at Argonne National Laboratory, providing detailed machining tolerance and defects from manufacturing and a realistic rough surface. For comparison, a nominal geometry and a modified geometry incorporating measured large-scale geometric features but no surface details were also used in the simulations. Spray characteristics such as mass flow rate, injection velocity, and Sauter mean diameter were analyzed. Significantly distinct spray characteristics in terms of injection velocity, spray morphology, and primary breakup mechanism were predicted using different nozzle geometries, which is mainly attributable to the realistic surface finish and manufacturing defects. The measured high-resolution geometry predicts a lower injection velocity, a wider-spreading spray, and an overall slower breakup rate with evident injector tip wetting compared to the ideally smooth nozzle boundary. This result implies that the manufacturing details of the injector, which are usually ignored in fuel injection studies, have a significant impact on the spray development process and should be taken into account for design optimization.

Yue, Zongyu↗
NASA NTRS2010

Converting a C-130 Hercules into a Compound Helicopter: A Conceptual Design Study

This study presents the performance and weight changes for a Compound C-130 as compared to the Baseline C-130H Hercules, using NDARC as the primary analysis tool. First, the C-130H was modeled within NDARC, from which performance at various conditions and a parametric weight statement were generated. Then, the C-130H NDARC file was modified to represent the Compound C-130, which was then put through the same performance analysis as the C-130H. A parametric weight statement was also calculated for the Compound C-130, which allowed for comparison to the C-130H. As part of the modeling of the Compound C-130, a Rotor Design Spreadsheet was created that would allow the direct calculation of the weight of the main rotors being added. Using composite materials led to considerable weight savings for both the rotor system and the hub weights. These weight savings are reflected in the NDARC Technology Factors which were determined to be 0.71 and 0.5 for the rotor blades and the hub/hinge system, respectively. Such Technology Factors suggest that using composites for other components could drastically lighten the Operating Empty Weight of the aircraft. The weight statements show the weights for each of the components on each aircraft. It is quite evident that the Compound C-130 has a higher Operating Empty Weight due to the addition of the two main rotors and a drive system to connect each engine group on the wing tips. Upon further analysis, the main weight driver is the drive system. While the main rotor/hub/hinge weight increase is to be expected, the weight increase due to the transmission drive and gear boxes are cause for concern. Unless a method can be found of reducing the weight of the drive system, the weight penalty makes the Compound a C-130 an inefficient aircraft in terms of payload/fuel capacity. Possible solutions are either off-loading some of the power requirements through the drive system or using composite materials in the construction of the drive system. The performance of the Compound C-130 versus the C-130H shows a clear need for more powerful engines than are currently present on the C-130H. This would also adversely affect the Operating Empty Weight since a larger power plant requires more weight. However, one advantage that the Compound C-130 presents is the ability to hover and operate at low speeds in Helicopter Mode. While the C-130H is unable to travel at speeds lower than its stall speed, the Compound C-130 is able to hover using the main rotors. Thus, the Compound C-130 is able to operate independent of runways, let alone the condition of the nearest runway. Ultimately, the Compound C-130 is an effective aircraft in theaters requiring VTOL aircraft due to geographical considerations in terms or performance. Unfortunately, the weight penalty associated with converting the C-130H to a Compound C-130 suggests that further work in the area of the drive systems is required.

Kottapalli, Anjaney P.↗
NASA NTRS1994

Cracking characteristics of a habitable module pressure wall following orbital debris penetration

All long-duration spacecraft in low-earth-orbit are subject to high speed impacts by meteoroids and pieces of orbital debris. The threat of damage from such impacts is a significant design consideration in the development of long duration earth-orbiting spacecraft. This report presents the results of a study whose objective was to develop an empirical model to predict the magnitude of the various cracking and through-hole creation phenomena accompanying a habitable module penetration. The significance of the work performed is that the model predictions can be fed directly into a survivability analysis to determine whether or not module unzipping would occur under a specific set of impact conditions. The likelihood of module unzipping over a structure's lifetime can also be determined in such an analysis. In addition, effective hole size predictions can be used as part of a survivability analysis to determine the time available for module evacuation prior to the onset of incapacitation due to air loss. Some of the phenomena considered include maximum petal length, maximum tip-to-tip crack distance, depth of petal deformation, number of cracks formed, orientation of the maximum tip-to-tip distance with respect to the inner wall grain direction, and the effective inner wall hole diameter.

Schonberg, William P.↗
NASA NTRS1997

Exploratory Investigation of Forebody Strakes for Yaw Control of a Generic Fighter with a Symmetric 60 deg Half-Angle Chine Forebody

Forebody strakes were tested in a low-speed wind tunnel to determine their effectiveness producing yaw control on a generic fighter model with a symmetric 60 deg half-angle chine forebody. Previous studies conducted using smooth, conventionally shaped forebodies show that forebody strakes provide increased levels of yaw control at angles of attack where conventional rudders are ineffective. The chine forebody shape was chosen for this study because chine forebodies can be designed with lower radar cross section (RCS) values than smooth forebody shapes. Because the chine edges of the forebody would fix the point of flow separation, it was unknown if any effectiveness achieved could be modulated as was successfully done on the smooth forebody shapes. The results show that use of forebody strakes on a chine forebody produce high levels of yaw control, and when combined with the rudder effectiveness, significant yaw control is available for a large range of angles of attack. The strake effectiveness was very dependent on radial location. Very small strakes placed at the tip of the forebody were nearly as effective as very long strakes. An axial translation scheme provided almost linear increments of control effectiveness.

Ross, Holly M.↗
NASA NTRS1961

Free-Flight Skin-Temperature and Surface-Pressure Measurements on a Highly Polished Nose Having a 100 deg Total-Angle Cone and a 10 deg Half-Angle Conical Flare Section up to a Mach Number of 4.08

The skin temperature and surface pressure were measured on a large-scale, highly polished nose having a relatively sharp-tipped 100 deg total-angle cone followed by a conical flare section of 10 deg half-angle. The measurements were obtained in flight from a rocket-propelled model up to a peak Mach number of 4.08 and a peak Reynolds number of 22 x 10(exp 6) per foot. Temperature distributions indicated that the heating on the forward 3.5 inches of the 100 deg cone was lower than the heating on the rearward portion. Likewise, measured temperatures on the flare portion of the test nose were generally lower than the temperatures on the 100 deg cone portion. The data indicated that the local Reynolds numbers of transition, based on calculated boundary-layer momentum thicknesses, ranged from 530 to 940 for a Mach number range from 2.72 to 3.75. Comparison of measured cone pressures with theory for a sharp cone showed that theory overestimates the cone pressures. Pressure measurements on the flare portion of the nose showed that in the lower speed range the flow expands below atmospheric pressure in going from the cone to the flare; however, as the speed increased, the expansion diminished and for speeds greater than a Mach number of approximately 3.0 the flare pressure coefficients were at or near a value of zero.

Rashis, Bernard↗
DOE OSTI2020

Collaborative Research: Advancing Arctic Climate Projection Capability at Seasonal to Decadal Scales (Final Technical Report)

The Regional Arctic System Model (RASM) at process resolving configurations has been used to (i) advance understanding of physical processes and feedbacks involved in Arctic amplification and (ii) understand and potentially reduce uncertainty in prediction of arctic climate change at seasonal to decadal scales. RASM consists the atmosphere (Weather and Research Forecasting model, WRF), ocean (Parallel Ocean Program, POP), sea ice (CICE), land hydrology (Variable Infiltration Capacity model, VIC), river routing scheme (RVIC), marine biogeochemistry components and the coupling framework (CPL7). Its domain is pan-Arctic, with the atmosphere and land components configured on a 50-km or 25-km grid and four configurations of the ocean and sea ice components: 1/12°(~9.3km) or 1/48°(~2.4km) and 45 or 60 vertical layers. These RASM configurations have been motivated by the emerging exascale capability for high performance computing to improve model fidelity. The dynamical downscaling of reanalysis allows comparison of RASM results with observations in place and time to: (i) advance system level understanding of physical processes and coupling involved in an event, (ii) optimize model parameter space, (iii) diagnose and reduce model biases and (iv) produce realistic and consistent across all the components initial conditions for predictions and predictability studies, which are all unique capabilities not available in global Earth System Models (ESMs). An evaluation of RASM 1.0 (Cassano et al. 2017) revealed that it had a cold bias over the oceans and a warm bias over land areas due largely to cloud and radiation biases in the model, with too little cloud cover simulated over land and too much cloud cover simulated over sub-polar oceans. This study has motivated an upgrade to WRF version 3.7.1 in RASM and allowed for the inclusion of the radiative impact of convective clouds. A variety of atmospheric physics parameterizations were evaluated against observations (e.g. data from the Arctic Clouds in Summer Experiment (ACSE); Sedlar et al. 2020) to identify an optimal suite of WRF physics options in RASM. The RASM with the optimized WRF physics were used to study the impact of strong mesoscale winds over the ocean around the southern tip of Greenland (DuVivier and Cassano 2016) and their impact on oceanic convection (DuVivier et al. 2017a). Data from the PolarWinds field campaign were used to evaluate WRF boundary layer physics and resolution impacts on the simulation of a Greenland barrier wind event (DuVivier et al. 2017b). The RVIC streamflow routing model has been implemented in RASM to realistically represent high-resolution streamflow processes (Hamman et al. 2017) and to couple the land buoyancy fluxes to the ocean. The RASM-RVIC high-resolution data set of all coastal freshwater fluxes for the Arctic drainage basin and surrounding areas for 1979-2014 was published as a separate product (https://doi.org/10.5281/zenodo.293037). The fidelity of atmospheric momentum transfer to and the response of polar marine Ekman layer in RASM and Community Earth System Model (CESM) was investigated by Roberts et al. (2015). The increased frequency of oceanic flux exchange in CESM, following the RASM guidance, caused a considerable increase in the median inertial ice speed across the Southern Ocean and parts of the Arctic. A comprehensive evaluation of the RASM1.0 atmosphere-ocean-sea ice-land interface was completed by Brunke et al. (2018). RASM was also demonstrated for its capability to simulate extreme events in agreement with observations in space and time (Lee et al. submitted). In particular, the development of three open water events, known as polynyas, have been simulated north of Greenland in February of 2011, 2017 and 2018, in agreement with satellite observations for the past four decades. The optimized RASM sea ice results have been favorably evaluated against satellite observations and a subset of eleven CMIP6 models (Watts et al. submitted). In a complementary project, Jin et al. (2018) have shown that RASM with higher-resolution and new sea-ice processes contributed to lower model errors in sea-ice conditions, concentrations of nutrients and ice algae, in comparison to results from the coarse-resolution (1°) CESM. In two other complementary studies, RASM results were used (i) to explain areas of concentrated use by bowhead whales, the seasonal progression in the use, and the physical environment within those areas (Citta et al. 2015) and (ii) for a synthesis of fall bowhead whales distribution and migration in the Bering-Chukchi-Beaufort (BCB) Sea to investigate whale movements and feeding to the local ocean hydrography and currents (Citta et al. 2018). However, the multi-decadal output from the CESM Large Ensemble yielded unrealistic forcing. Instead, the shorter NCEP CFSv2 9-month forecasts were successfully tested and afforded an increased ensemble size (~30) to demonstrate gains of dynamical downscaling at sub-seasonal to intra-annual time scales. The improved model physics and coupling among RASM model components have yielded more realistic representation of the sea ice cover and consistent across all model components initial conditions. Consequently, RASM demonstrates significant gains compared to simulation of sea ice in the NCEP reanalysis. In addition, RASM 6-month ensemble forecasts yield very realistic sea ice distribution, which demonstrates both significant gains of dynamical downscaling and the continued impact of the initial conditions on forecasts out to 6 months (https://nps.edu/web/rasm/predictions). A follow up study using RASM for dynamical downscaling of the more realistic CESM initialized Decadal Prediction Large Ensemble output is currently ongoing as part of the DOE RGMA HiLAT-RASM project.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2016

Electrostatic and aerodynamic forced vibrations of a thin flexible electrode: Quasi-periodic vs. chaotic oscillations

In this paper, transverse vibrations of an electrostatically actuated thin flexible cantilever perturbed by low-speed air flow are studied using both experiments and numerical modeling. In the experiments, the dynamic characteristics of the cantilever are studied by supplying a DC voltage with an AC component for electrostatic forcing and a constant uniform air flow around the cantilever system for aerodynamic forcing. A range of control parameters leading to stable vibrations are established using a dimensionless operating parameter that is the ratio of the induced and the free stream velocities. Numerical results are validated with experimental data. Assuming the amplitude of vibrations are small, then a non-linear dynamic Euler-Bernoulli beam equation with viscous damping and gravitational effects is used to model the equation of motion. Aerodynamic forcing is modelled as a temporally sinusoidal and uniform force acting perpendicular to the beam length. The forcing amplitude is found to be proportional to the square of the air flow velocity. Numerical results strongly agree with the experiments predicting accurate vibration amplitude, displacement frequency, and quasi-periodic displacement of the cantilever tip.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1954

Additional Results on the Static Longitudinal and Lateral Stability Characteristics of a 0.05-Scale Model of the Convair F2Y-1 Airplane at High Subsonic Speeds

Additional results on the static longitudinal and lateral stability characteristics of a 0.05-scale model of the Convair F2Y-1 water-based fighter airplane were obtained in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.50 to 0.92. The maximum angle-of-attack range (obtained at the lower Mach numbers) was from -2 degrees to 25 degrees. The sideslip-angle range investigated was from -4 degrees to 12 degrees. The investigation included effects of various arrangements of wing fences, leading-edge chord-extensions, and leading-edge notches. Various fuselage fences, spoilers, and a dive brake also were investigated. From overall considerations of lift, drag, and pitching moments, it appears that there were two modifications somewhat superior to any of the others investigated: One was a configuration that employed a full-chord fence and a partial-chord fence located at 0.63 semispan and 0.55 semispan, respectively. The second was a leading-edge chord-extension that extended from 0.68 semispan to 0.85 semispan in combination with a leading-edge notch located at 0.68 semispan. With plus or minus 10 degrees aileron, the estimated wing-tip helix angle was reduced from 0.125 at a Mach number of 0.50 to 0.088 at a Mach number of 0.92, with corresponding rates of roll of 4.0 and 5.2 radians per second. The upper aft fuselage dive brake, when deflected 30 degrees and 60 degrees, reduced the rudder effectiveness about 10 to 20 percent and about 35 to 50 percent, respectively.

Spreeman, Kenneth P.↗
NASA NTRS1957

Experimental Investigation of Effects of Moderate Sideslip on the Flow Fields near a 45 Degree Swept-wing-fuselage Combination at Low Speed

The flow fields near a 45 degree swept-wing-fuselage combination at moderate angles of sideslip (plus-or-minus 8 degrees), as determined experimentally at low speed, are presented as variations with chordwise distance for various spanwise and vertical locations and angles of attack. The results indicated that for positions close to the fuselage (on and near the plane of symmetry) changes in the angle of sideslip caused large changes in the flow-field characteristics and particularly in the local angles of sideslip, which in some cases were nearly double the static angle of sideslip. In general, the effects of changing the angle of sideslip on the flow-field characteristics for all of the outboard underwing locations were qualitatively similar, although conditions at the more inboard and outboard locations were somewhat more severe for lifting conditions than at the one-half semispan location. The chordwise gradients in the flow parameters for the underwing locations were more severe than for the fuselage locations although the effect of changing the angle of sideslip was less severe, in that the incremental changes in the local angles of sideslip were approximately equal to the static angle of sideslip. Flow conditions near the wing tip were found to be critically dependent on vertical location, with the largest sideslip-induced variations occurring at the nearest vertical locations. The results also indicated that for the outboard underwing locations the wing was the predominant factor in disturbing the field of flow for the conditions investigated.

Alford, William J , Jr↗
DOE OSTI2018

3D treatment planning systems

Three-dimensional (3D) treatment planning systems have evolved and become crucial components of modern radiation therapy. The systems are computer-aided designing or planning softwares that speed up the treatment planning processes to arrive at the best dose plans for the patients undergoing radiation therapy. Furthermore, the systems provide new technology to solve problems that would not have been considered without the use of computers such as conformal radiation therapy (CRT), intensity-modulated radiation therapy (IMRT), and volumetric modulated arc therapy (VMAT). The 3D treatment planning systems vary amongst the vendors and also the dose delivery systems they are designed to support. As such these systems have different planning tools to generate the treatment plans and convert the treatment plans into executable instructions that can be implemented by the dose delivery systems. The rapid advancements in computer technology and accelerators have facilitated constant upgrades and the introduction of different and unique dose delivery systems than the traditional C-arm type medical linear accelerators. The focus of this special issue is to gather relevant 3D treatment planning systems for the radiation oncology community to keep abreast of technology advancement by assess the planning tools available as well as those unique ''tricks or tips'' used to support the different dose delivery systems.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
NASA NTRS1954

Effects of Sweep and Thickness on the Static Longitudinal Aerodynamic Characteristics of a Series of Thin, Low-aspect-ratio, Highly Tapered Wings at Transonic Speeds : Transonic-bump Method

An investigation by the transonic-bump technique of the static longitudinal aerodynamic characteristics of a series of thin, low-aspect-ratio, highly tapered wings has been made in the Langley high-speed 7- by 10-foot tunnel. The Mach number range extended from about 0.60 to 1.18, with corresponding Reynolds numbers ranging from about 0.75 x 10(6) to 0.95 x 10(6). The angle of attack range was from -10 degrees to approximately 32 degrees.The effects on drag and lift-drag ratio of a variation in sweep angle from -14.03 degrees to 45 degrees with respect to the quarter-chord line for wings of 3-percent-chord thickness was found to be small in comparison to the effects of a variation in thickness from 2 percent chord to 4.5 percent chord for wings with 14.03 degree sweepback. For the range of variables considered, variations in plan form were considerably more important with regard to longitudinal stability characteristics than the variations in thickness. For the series of basic wings having an aspect ratio of 4, the most hearly linear pitching-moment characteristics were obtained with 26.57 degree of sweepback of the quarter-chord line. However, for the modified series of wings (obtained by clipping the tips of the original wings parallel to the plane of symmetry to give an aspect ratio of 3 and a taper ratio of 0.143), the most nearly linear pitching-moment characteristics were obtained with 36.87 degrees of sweepback. By decreasing the thickness-to-chord ratios from 0.03 to 0.02, a large increase in lift-curve slope was obtained for both the basic and modified wings. All of the wings of both series had fairly large inward shifts of the lateral center-of-pressure location (indicative of tip stalling) with increasing lift coefficient, except those wings having minimum sweepback angles.

Fournier, Paul G↗
NASA NTRS1981

Transonic flutter study of a wind-tunnel model of an arrow-wing supersonic transport

A 1/20-size, low-speed flutter model of the SCAT-15F complete airplane was tested on cables to simulate a near free-flying condition. Only the model wing and fuselage were flexible. Flutter boundaries were measured for a nominal configuration and a configuration with wing fins removed at Mach numbers M from 0.76 to 1.2. For both configurations, the transonic dip in the wing flutter dynamic pressure q boundary was relatively small and the minimum flutter q occurred near M = 0.92. Removing the wing fins increased the flutter q about 14 percent and changed the flutter mode from symmetric to antisymmetric. Vibration and flutter analyses were made using a finite-element structural representation and subsonic kernel-function aerodynamics. For the nominal configuration, the analysis (using calculated modal data) predicted the experimental flutter q levels within 10 percent but did not predict the correct flutter mode at the higher M. For the configuration without wing fins, the analysis predicted 16 to 36 percent unconservative (higher than experimental) flutter q levels and showed extreme sensitivity to mass representation details that affected wing tip mode shapes. For high subsonic M, empennage aerodynamics had a significant effect on the predicted flutter boundaries of several symmetric modes.

Ruhlin, C. L.↗
NASA NTRS1996

Subsonic Aerodynamic Characteristics of a Circular Body Earth-to-Orbit Vehicle

A test of a generic reusable earth-to-orbit transport was conducted in the 7- by 10-Foot high-speed tunnel at the Langley Research Center at Mach number 0.3. The model had a body with a circular cross section and a thick clipped delta wing as the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center vertical fin, wingtip fins, and a nose-mounted vertical fin. The configuration was longitudinally stable about the estimated center-of-gravity position of 0.72 body length and had sufficient pitch-control authority for stable trim over a wide range of angle of attack, regardless of fin arrangement. The maximum trimmed lift/drag ratio for the aft center-fin configuration was less than 5, whereas the other configurations had values of above 6. The aft center-fin configuration was directionally stable for all angles of attack tested. The wingtip and nose fins were not intended to produce directional stability but to be active controllers for artificial stabilization. Small rolling-moment values resulted from yaw control of the nose fin. Large adverse rolling-moment increments resulted from tip-fin controller deflection above 13 deg angle of attack. Flow visualization indicated that the adverse rolling-moment increments were probably caused by the influence of the deflected tip-fin controller on wing flow separation.

Lepsch, Roger A., Jr.↗
DOE OSTI2024

Surface Meteorological System (MET) Instrument Handbook

The Surface Meteorological System (MET) consist mainly of conventional in situ sensors that obtain a defined “core” set of measurements. The core set of measurements is: Barometric Pressure (kPa), Temperature (°C), Relative Humidity (%), Arithmetic-Averaged Wind Speed (m/s), Vector-Averaged Wind Speed (m/s), and Vector-Averaged Wind Direction (deg). The sensors that collect the core variables are mounted at the standard heights defined for each variable: • Winds: 10 meters • Temperature and Relative Humidity: 2 meters • Barometric Pressure: 1 meter. Depending upon the geographical location, different models and types of sensors may be used to measure the core variables due to the conditions experienced at those locations. Most sites have additional sensors that measure other variables that are unique to that site or are well suited for the climate of the location but not at others.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2009

Large Eddy Simulation of Transonic Flow Field in NASA Rotor 37

The current paper reports on numerical investigations on the flow characteristics in a transonic axial compressor, NASA Rotor 37. The flow field was used previously as a CFD blind test case conducted by American Society of Mechanical Engineers in 1994. Since the CFD blind-test exercise, many numerical studies on the flow field in the NASA Rotor 37 have been reported. Although steady improvements have been reported in both numerical procedure and turbulence closure, it is believed that all the important aspects of the flow field have not been fully explained with numerical studies based on the Reynolds Averaged Navier-Stokes (RANS) solution. Experimental data show large dip in total pressure distribution near the hub at downstream of the rotor at 100% rotor speed. Most original numerical solutions from the blind test exercise did not predict this total pressure deficit correctly. This total pressure deficit at the rotor exit was attributed to a hub corner flow separation by the author. Several subsequent numerical studies with different turbulence closure model also calculated this dip in total pressure rise. Also, several studies attributed this total pressure deficit to a small leakage flow coming from the hub in the test article. As the experimental study cannot be repeated, either explanation cannot be validated. The primary purpose of the current investigation is to investigate the transonic flow field with both RANS and a Large Eddy Simulation (LES). The RANS approach gives similar results presented at the original blind test exercise. Although the RANS calculates higher overall total pressure rise, the total pressure deficit near the hub is calculated correctly. The numerical solution shows that the total pressure deficit is due to a hub corner flow separation. The calculated pressure rise from the LES agrees better with the measured total pressure rise especially near the casing area where the passage shock interacts with the tip clearance vortex and flow becomes unsteady due to this interaction. The LES simulation also calculates the total pressure rise deficit near the hub and it agrees well with the measured data.

Hah, Chunill↗