Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Space Operations Center”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Metallic Environmentally Resistant Coating Rapid Innovation Initiative

Lightweight alloys such as aluminum (Al) and titanium (Ti) are often specified for space systems to minimize mass while maintaining structural integrity [1,2]. Such alloys however, have poor tribological response (high friction and wear), especially in extreme space environments, which becomes worse with the additional presence of lunar regolith. This leads to short lifetimes and premature failures that will ultimately limit long term operations on the lunar surface [2]. This project is addressing this technology gap by developing advanced wear- and radiation-resistant coatings for lightweight parts to extend the life-time and sustainability of both lunar and Martian assets. Ceramics were considered for their high wear resistance, but were rejected because of their low fracture toughness, which would be especially problematic for structural components. The novel and existing coating technologies and deposition methods are being tested in this project. The coating materials are Boron Nitride-Aluminum (BN-Al), Nickle Titanium (NiTi), Aluminum Oxide (AlO3), Ti64 with hBN at 2 and 10 vol percent (Ti-2vol%hBN and Ti-10vol%hBN), and the deposition techniques are high pressure cold-spray (CS) and ambient and vacuum plasma-spray (APS and VPS) [3,4,5]. BN-Al, NiTi, Ti-2vol%hBN, and Ti-10vol%hBN were applied with all three deposition techniques, and AlO3 was applied only using the APS deposition technique. A tungstenite (WS2) film was applied to the NiTi VPS coating. The coating and deposition technique configurations are being tested against several key end-use performance parameters. The parameters include the capabilities of the coatings under wear environments such as regolith simulant, thermal cycling from high (120°C) to cryogenic (-173°C), high vacuum (~10-7 torr), and pre- and post-exposure to ionizing particle radiation. Wear tests include pin on disk, three-body abrasion, and surface erosion by high velocity regolith impacts. The initial down selection is being performed using on virgin and environmental exposure samples using pin on disk and three body abrasion wear tests. From preliminary assessment of this testing, a few configurations were eliminated. Ti-10vol%hBN could not be applied using CS application and NiTi could not be applied using APS or CS application so these configurations did not get tested. Early pin on disk wear tests showed poor wear performance of BN-Al so this coating was eliminated early in the testing process. AlO3 on Al substrate did not survive thermal cycling, but wear testing is continuing for AlO3 on Ti substrate. A more detailed analysis is being con-ducted to further reduce the number of configuration for phase II and III. Phase II testing will include conventionally and additively manufactured substrates with surface erosion testing. In phase III, the coatings will be applied to three mechanism types: channel and slot, ball and socket, and a hinge joint. Each will demonstrate a different type of wear incidence. The mechanisms and their base materials are of direct interest to the end users and infusion points: the Human Landing System (HLS) and the Lunar Surface Innovation Initiative (sustained lunar surface operations). The technology development project is based out of Marshall Space Flight Center, has partnered with Florida International University (Miami, FL) and Plasma Processes (Huntsville, Al), and is supported by a group of NASA mentors from different centers.

dust mitigation↗

NAIRAS Model transition to the CCMC: real-time dosimetric output and low-Earth orbit applications

NASA’s Nowcast of Atmospheric Ionizing Radiation for Aviation Safety (NAIRAS) model is areal-time, global, physics-based model originally developed to predict exposure to cosmic radiation to air travelers from both galactic and solar sources. A prototype operational NAIRAS model has provided tabular and graphical data products via its public web site for a number of years. We present the advances in the transition of NAIRAS to operations at the Community Coordinated Modeling Center (CCMC), located at NASA Goddard Space Flight Center, where global NAIRAS products are available for a real-time space weather version of the model. In addition, a runs-on-request version provides model output along user selected flight trajectories. We show the global dosimetric output from the model that are available in real-time as well as the new products developed to support commercial spaceflight missions to low-Earth orbit(LEO) and the International Space Station (ISS).

Guillaume Gronof↗

Verification Test of Automated Robotic Assembly of Space Truss Structures

A multidisciplinary program has been conducted at the Langley Research Center to develop operational procedures for supervised autonomous assembly of truss structures suitable for large-aperture antennas. The hardware and operations required to assemble a 102-member tetrahedral truss and attach 12 hexagonal panels were developed and evaluated. A brute-force automation approach was used to develop baseline assembly hardware and software techniques. However, as the system matured and operations were proven, upgrades were incorporated and assessed against the baseline test results. These upgrades included the use of distributed microprocessors to control dedicated end-effector operations, machine vision guidance for strut installation, and the use of an expert system-based executive-control program. This paper summarizes the developmental phases of the program, the results of several assembly tests, and a series of proposed enhancements. No problems that would preclude automated in-space assembly or truss structures have been encountered. The test system was developed at a breadboard level and continued development at an enhanced level is warranted.

Rhodes, Marvin D.↗

Transformational Spaceport and Range Concept of Operations: A Vision to Transform Ground and Launch Operations

The Transformational Concept of Operations (CONOPS) provides a long-term, sustainable vision for future U.S. space transportation infrastructure and operations. This vision presents an interagency concept, developed cooperatively by the Department of Defense (DoD), the Federal Aviation Administration (FAA), and the National Aeronautics and Space Administration (NASA) for the upgrade, integration, and improved operation of major infrastructure elements of the nation s space access systems. The interagency vision described in the Transformational CONOPS would transform today s space launch infrastructure into a shared system that supports worldwide operations for a variety of users. The system concept is sufficiently flexible and adaptable to support new types of missions for exploration, commercial enterprise, and national security, as well as to endure further into the future when space transportation technology may be sufficiently advanced to enable routine public space travel as part of the global transportation system. The vision for future space transportation operations is based on a system-of-systems architecture that integrates the major elements of the future space transportation system - transportation nodes (spaceports), flight vehicles and payloads, tracking and communications assets, and flight traffic coordination centers - into a transportation network that concurrently accommodates multiple types of mission operators, payloads, and vehicle fleets. This system concept also establishes a common framework for defining a detailed CONOPS for the major elements of the future space transportation system. The resulting set of four CONOPS (see Figure 1 below) describes the common vision for a shared future space transportation system (FSTS) infrastructure from a variety of perspectives.

Source record↗

THE LIQUID NITROGEN SYSTEM FOR CHAMBER A; A CHANGE FROM ORIGINAL FORCED FLOW DESIGN TO A NATURAL FLOW (THERMO SIPHON) SYSTEM

NASA at the Johnson Space Center (JSC) in Houston is presently working toward modifying the original forced flow liquid nitrogen cooling system for the thermal shield in the space simulation chamber-A in Building 32 to work as a natural flow (thermo siphon) system. Chamber A is 19.8 m (65 ft) in diameter and 35.66 m (117 ft) high. The LN{sub 2} shroud environment within the chamber is approximately 17.4 m (57 ft) in diameter and 28 m (92 ft) high. The new thermo siphon system will improve the reliability, stability of the system. Also it will reduce the operating temperature and the liquid nitrogen use to operate the system. This paper will present the requirements for the various operating modes. System level thermodynamic comparisons of the existing system to the various options studied and the final option selected will be outlined. A thermal and hydraulic analysis to validate the selected option for the conversion of the current forced flow to natural flow design will be discussed. The proposed modifications to existing system to convert to natural circulation (thermo siphon) system and the design features to help improve the operations, and maintenance of the system will be presented.

42 ENGINEERING↗

Developing Fabrication Technologies to Provide On Demand Manufacturing for Exploration of the Moon and Mars

NASA's human exploration initiative poses great opportunity and risk for manned and robotic missions to the Moon, Mars, and beyond. Engineers and scientists at the Marshall Space Flight Center (MSFC) are developing technologies for in situ fabrication capabilities during lunar and Martian surface operations utilizing provisioned and locally refined materials. Current fabrication technologies must be advanced to support the special demands and applications of the space exploration initiative such as power, weight and volume constraints. In Situ Fabrication and Repair (ISFR) will advance state-of-the-art technologies in support of habitat structure development, tools, and mechanical part fabrication. The repair and replacement of space mission components, such as life support items or crew exercise equipment, fall within the ISFR scope. This paper will address current fabrication technologies relative to meeting ISFR targeted capabilities, near-term advancement goals, and systematic evaluation of various fabrication methods.

Hammond, Monica S.↗

Simulator Evaluation of Runway Incursion Prevention Technology for General Aviation Operations

A Runway Incursion Prevention System (RIPS) has been designed under previous research to enhance airport surface operations situation awareness and provide cockpit alerts of potential runway conflict, during transport aircraft category operations, in order to prevent runway incidents while also improving operations capability. This study investigated an adaptation of RIPS for low-end general aviation operations using a fixed-based simulator at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC). The purpose of the study was to evaluate modified RIPS aircraft-based incursion detection algorithms and associated alerting and airport surface display concepts for low-end general aviation operations. This paper gives an overview of the system, simulation study, and test results.

Jones, Denise R.↗

Evaluation of the VIIRS Land Algorithms at Land PEATE

The Land Product Evaluation and Algorithm Testing Element (Land PEATE), a component of the Science Data Segment of the National Polar-orbiting Operational Environmental Satellite System (NPOESS) Preparatory Project (NPP), is being developed at the NASA Goddard Space Flight Center (GSFC). The primary task of the Land PEATE is to assess the quality of the Visible Infrared Imaging Radiometer Suite (VIIRS) Land data products made by the Interface Data Processing System (IDPS) using the Operational (OPS) Code during the NPP era and to recommend improvements to the algorithms in the IDPS OPS code. The Land PEATE uses a version of the MODIS Adaptive Processing System (MODAPS), NPPDAPS, that has been modified to produce products from the IDPS OPS code and software provided by the VIIRS Science Team, and uses the MODIS Land Data Operational Product Evaluation (LDOPE) team for evaluation of the data records generated by the NPPDAPS. Land PEATE evaluates the algorithms by comparing data products generated using different versions of the algorithm and also by comparing to heritage products generated from different instrument such as MODIS using various quality assessment tools developed at LDOPE. This paper describes the Land PEATE system and some of the approaches used by the Land PEATE for evaluating the VIIRS Land algorithms during the pre-launch period of the NPP mission and the proposed plan for long term monitoring of the quality of the VIIRS Land products post-launch.

Wolfe, Robert E.↗

Shuttle tethered operations: The effect on orbital trajectory and inertial navigation

The first full scale test of a large tethered satellite system is planned. The Orbiter will be linked to a 500 kg payload by a 20 km tether, an action with a profound effect on the trajectory of the Orbiter. For the first time in the history of the Shuttle program, the vehicle will conduct prolonged operations with the center of mass of the orbiting system a significant distance from the center of mass of the Space Shuttle Orbiter, a violation of the fundamental assumption made in both the Orbiter ground-based and onboard navigation software. Inertial navigation of tethered operations with the Shuttle is further complicated by the presence of non-conservative forces in the system: Reaction Control System (RCS) translational effects, atmospheric drag, and electro-magnetic dynamics. These can couple with the conservative tether dynamics effects, and degrade the navigation software performance. The primary effects are examined on the Orbiter's trajectory, coupling by conservative forces during tethered operations, and the impact of both on the ability to meet inertial navigation constraints. The impact of electrodynamics, different RCS control modes, commanded attitudes, and attitude deadbands are presented. Operational guidelines which optimize successful mission navigation, and necessary navigation constraints are discussed.

Lardas, Mark N.↗

Vacuum Ultraviolet Radiation and Atomic Oxygen Durability Evaluation of HST Bi-Stem Thermal Shield Materials

Bellows-type thermal shields were used on the bi-stems of replacement solar arrays installed on the Hubble Space Telescope (HST) during the first HST servicing mission (SMI) in December 1993. These thermal shields helped reduce the problem of thermal gradient- induced jitter observed with the original HST solar arrays during orbital thermal cycling and have been in use on HST for eight years. This paper describes ground testing of the candidate solar array bi-stem thermal shield materials including backside aluminized Teflon(R)FEP (fluorinated ethylene propylene) with and without atomic oxygen (AO) and ultraviolet radiation protective surface coatings for durability to AO and combined AO and vacuum ultraviolet (VOV) radiation. NASA Glenn Research Center (GRC) conducted VUV and AO exposures of samples of candidate thermal shield materials at HST operational temperatures and pre- and post-exposure analyses as part of an overall program coordinated by NASA Goddard Space Flight Center (GSFC) to determine the on-orbit durability of these materials. Coating adhesion problems were observed for samples having the AO- and combined AO/UV-protective coatings. Coating lamination occurred with rapid thermal cycling testing which simulated orbital thermal cycling. This lack of adhesion caused production of coating flakes from the material that would have posed a serious risk to HST optics if the coated materials were used for the bi-stem thermal shields. No serious degradation was observed for the uncoated aluminized Teflon(R) as evaluated by optical microscopy, although atomic force microscopy (AFM) microhardness testing revealed that an embrittled surface layer formed on the uncoated Teflon(R) surface due to vacuum ultraviolet radiation exposure. This embrittled layer was not completely removed by AO erosion, No cracks or particle flakes were produced for the embrittled uncoated material upon exposure to VUV and AO at operational temperatures to an equivalent exposure of approximately five years in the HST environment. Uncoated aluminized FEP Teflon(R) was determined to be the most appropriate thermal shield material and was used on the bi-stems of replacement solar arrays installed on HST during SMI in December 1993. The SMI -installed solar arrays air scheduled to be replaced during MST's fourth servicing mission (SM3B) in early 2002.

Dever, Joyce↗

Payloads simulation in the Shuttle Mission Training Facility

The Shuttle Mission Training Facility (SMFT) at the NASA Johnson Space Center is the primary facility for full mission training of astronauts. The training provided in the SMTF includes payload operations that are performed by the astronauts while the Space Shuttle is in orbit. This training requires real-time simulation of the operational aspects of Shuttle payloads as well as simulation of the interaction between payloads and the Orbiter. For this purpose the SMTF contains Payloads Simulators (PLS) that are coupled to and operated in synchronization with the Shuttle Vehicle Simulators. The PLS are used for simulating all payloads with the exception of the European Space Agency's Spacelab. The SMTF contains a separate Spacelab Simulator for training Spacelab astronauts. This paper provides a synopsis of actual payload operations, the methodology for payload simulation in the SMTF, and the system architecture of the PLS.

Hajare, Ankur R.↗

MCC flight operations automation of STS orbiter systems monitoring

The integration of new capabilities into the Mission Control Center at the Johnson Space Center in Houston, Texas in order to improve the data monitoring and analysis of the STS is discussed. User interface application software and systems, such as the flight data file Shuttle mission simulator and failure analysis program, to be utilized for flight operations automation are examined. Consideration is given to task automation, the trend monitoring system, the data retrieval system, and the launch processing system. The development and functions of the Shuttle data analysis system, which is to operate in real time, are described.

Bates, William V., Jr.↗

The OLI Radiometric Scale Realization Round Robin Measurement Campaign

A round robin radiometric scale realization was performed at the Ball Aerospace Radiometric Calibration Laboratory in January/February 2011 in support of the Operational Land Imager (OLI) Program. Participants included Ball Aerospace, NIST, NASA Goddard Space Flight Center, and the University of Arizona. The eight day campaign included multiple observations of three integrating sphere sources by nine radiometers. The objective of the campaign was to validate the radiance calibration uncertainty ascribed to the integrating sphere used to calibrate the OLI instrument. The instrument level calibration source uncertainty was validated by quatnifying: (1) the long term stability of the NIST calibrated radiance artifact, (2) the responsivity scale of the Ball Aerospace transfer radiometer and (3) the operational characteristics of the large integrating sphere.

Cutlip, Hansford↗

Runway Incursion Prevention for General Aviation Operations

A Runway Incursion Prevention System (RIPS) and additional incursion detection algorithm were adapted for general aviation operations and evaluated in a simulation study at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) in the fall of 2005. RIPS has been designed to enhance surface situation awareness and provide cockpit alerts of potential runway conflicts in order to prevent runway incidents while also improving operational capability. The purpose of the study was to evaluate the airborne incursion detection algorithms and associated alerting and airport surface display concepts for general aviation operations. This paper gives an overview of the system, simulation study, and test results.

Jones, Denise R.↗

Runway Incursion Prevention System for General Aviation Operations

A Runway Incursion Prevention System (RIPS) and additional incursion detection algorithm were adapted for general aviation operations and evaluated in a simulation study at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) in the fall of 2005. RIPS has been designed to enhance surface situation awareness and provide cockpit alerts of potential runway conflicts in order to prevent runway incidents while also improving operational capability. The purpose of the study was to evaluate the airborne incursion detection algorithms and associated alerting and airport surface display concepts for general aviation operations. This paper gives an overview of the system, simulation study, and test results.

Jones, Denise R.↗

TESS Science Processing Operations Center Pipeline and Data Products

TESS launched 18 April 2018 to conduct a two-year, near all-sky survey for at least 50 small, nearby exoplanets for which masses can be ascertained and whose atmospheres can be characterized by ground- and space-based follow-on observations. TESS just completed its survey of the southern hemisphere, identifying >600 candidate exoplanets and unveiling a plethora of exciting non-exoplanet astrophysics results, such as asteroseismology, asteroids, and supernova. The TESS Science Processing Operations Center (SPOC) processes the data downlinked every two weeks to generate a range of data products hosted at the Mikulski Archive for Space Telescopes (MAST). For each sector (~1 month) of observations, the SPOC calibrates the image data for both 30-min Full Frame Images (FFIs) and up to 20,000 pre-selected 2-min target star postage stamps. Data products for the 2-min targets include simple aperture photometry and systematic error-corrected flux time series. The SPOC also conducts searches for transiting exoplanets in the 2-min data for each sector and generates Data Validation time series and associated reports for each transit-like feature identified in the search. Multi-sector searches for exoplanets are conducted periodically to discover longer period planets, including those in the James Webb Continuous Viewing Zone (CVZ), which are observed for up to one year. Data products also include co-trending basis vectors (CBVs) and calibration files, such as the Pixel Response Functions across the field of view of each of TESS's four cameras. To maximize the usability, the TESS science data products are modeled after those for Kepler, including Target Pixel Files and Light Curve files.In this talk, I describe the SPOC pipeline and the chief differences between the TESS and the Kepler pipelines, and the major updates to the SPOC pipeline (4.0) available now to the community at MAST. I also discuss the documentation available to the community to help them in properly interpreting and analyzing the TESS data products.The TESS Mission is funded by NASA's Science Mission Directorate as an Astrophysics Explorer Mission.

Jenkins, Jon M.↗

Telescience Operations on International Space Station

This paper describes the concept of telescience operations for the International Space Station (ISS). The extended duration microgravity environment of the ISS will enable microgravity science research to enter into a new era of increased scientific and technological data return. The National Aeronautics and Space Administration (NASA) has a vision of distributed ground operations which enables the Principal Investigator direct interaction with his/her on-board experiment from his/her home location. This is the concept of telescience and is essential for maximizing the use of the long duration science environment that ISS provides. The goal of telescience is to provide the capability to fully tele-operate an experiment from any ground location in such a way as to increase the amount and quality of scientific and technological data return and decrease the operations cost of an individual experiment relative to the era of Space Shuttle experiments. This paper also describes the NASA Lewis Research Center (LeRC) implementation approach for the LeRC Telescience Support Center (TSC) and Principal Investigator Science Operations Sites (SOS) which will fully meet the concept of telescience as prescribed by the Agency.

Schubert, Kathleen E.↗