Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Quantum Dots Investigated for Solar Cells

The NASA Glenn Research Center has been investigating the synthesis of quantum dots of CdSe and CuInS2 for use in intermediate-bandgap solar cells. Using quantum dots in a solar cell to create an intermediate band will allow the harvesting of a much larger portion of the available solar spectrum. Theoretical studies predict a potential efficiency of 63.2 percent, which is approximately a factor of 2 better than any state-of-the-art devices available today. This technology is also applicable to thin-film devices--where it offers a potential four-fold increase in power-to-weight ratio over the state of the art. Intermediate-bandgap solar cells require that quantum dots be sandwiched in an intrinsic region between the photovoltaic solar cell's ordinary p- and n-type regions (see the preceding figure). The quantum dots form the intermediate band of discrete states that allow sub-bandgap energies to be absorbed. However, when the current is extracted, it is limited by the bandgap, not the individual photon energies. The energy states of the quantum dot can be controlled by controlling the size of the dot. Ironically, the ground-state energy levels are inversely proportional to the size of the quantum dots. We have prepared a variety of quantum dots using the typical organometallic synthesis routes pioneered by Ba Wendi et al., in the early 1990's. The most studied quantum dots prepared by this method have been of CdSe. To produce these dots, researchers inject a syringe of the desired organometallic precursors into heated triocytlphosphine oxide (TOPO) that has been vigorously stirred under an inert atmosphere (see the following figure). The solution immediately begins to change from colorless to yellow, then orange and red/brown, as the quantum dots increase in size. When the desired size is reached, the heat is removed from the flask. Quantum dots of different sizes can be identified by placing them under a "black light" and observing the various color differences in their fluorescence (see the photograph).

Bailey, Sheila G.↗

Characterization of dangling bond defects at the crystalline Si/SiO x interface in a polycrystalline Si passivating contact solar cell at room temperature with electrically detected magnetic resonance spectroscopy

Monocrystalline silicon solar cells can achieve photoconversion efficiencies exceeding 26%; however, performance-limiting defects that trap carriers continue to be a challenge. In this work, we have characterized Si solar cells with tunneling SiO x /polycrystalline-Si (poly-Si) passivating contacts (TOPCon) on As-doped Czochralski Si wafers with electrically detected magnetic resonance (EDMR) spectroscopy. We fabricated 2 × 20 mm 2 TOPCon-like mini solar cells with edge passivation alongside larger 4 cm 2 sister cells and obtained similar device characteristics. We performed EDMR spectroscopy at 300 K on two minicells with different degrees of surface passivation based on the recombination parameter, J o , values of 40 and 310 fA/cm2. We optimized the resolution and the signal-to-noise ratio of the EDMR response of the minicells by varying the forward bias voltage and the magnetic field modulation amplitude. We detect two distinct signals with EDMR spectroscopy, an axial-like signal at g = 2.009, 2.0087, and 2.0015, and an isotropic signal at g = 2.0024, which we attribute to Si dangling bonds (P b0 and P b centers) and boron–oxygen related defects, respectively, at or near the c-Si/SiO x interface. The EDMR signals were lower for the cell with a lower value of J o , while the ratio of the two defect populations was very similar. The EDMR signal increases with forward bias but drops to zero at bias voltages >0.5 V, consistent with interface defects within or near the boron-doped emitter depletion region. Our study demonstrates a method to fabricate minicells that can be characterized with EDMR spectroscopy to detect industrially relevant defects in TOPCon cells.

14 SOLAR ENERGY↗

Metal nano-grids for transparent conduction in solar cells

A general procedure for predicting metal grid performance in solar cells was developed. Unlike transparent conducting oxides (TCOs) or other homogeneous films, metal grids induce more resistance in the neighbor layer. The resulting balance of transmittance, neighbor and grid resistance was explored in light of cheap lithography advances that have enabled metal nano-grid (MNG) fabrication. The patterned MNGs have junction resistances and degradation rates that are more favorable than solution-synthesized metal nanowires. Neighbor series resistance was simulated by the finite element method, although a simpler analytical model was sufficient in most cases. Finite-difference frequency-domain transmittance simulations were performed for MNGs with minimum wire width (w) of 50 nm, but deviations from aperture transmittance were small in magnitude. Depending on the process, MNGs can exhibit increased series resistance as w is decreased. However, numerous experimental reports have already achieved transmittance-MNG sheet resistance trade-offs comparable to TCOs. The transmittance, neighbor and MNG series resistances were used to parameterize a grid fill factor for a solar cell. In conclusion, this new figure of merit was used to demonstrate that although MNGs have only been employed in low efficiency solar cells, substantial gains in performance are predicted for decreased w in all high efficiency absorber technologies.

14 SOLAR ENERGY↗

Status of FEP encapsulated solar cell modules used in terrestrial applications

FEP (fluorinated ethylene propylene) encapsulated solar cell modules and arrays have been designed and built expressly for terrestrial applications. Solar cell power systems have been installed at three different land sites, while individual modules are undergoing marine-environment tests. Four additional power systems are being completed for installation during the summer of 1974. These tests have revealed some minor problems which have been corrected. The results confirm the inherent utility of FEP encapsulated terrestrial solar cell systems.

Ratajczak, A. F.↗

Limiting efficiency calculation of silicon single-nanowire solar cells with considering Auger recombination

Single-nanowire solar cells (SNSCs) have attracted considerable attention due to their unique light-harvesting capability mediated by the optical antenna effect and the high photoconversion efficiency due to the orthogonalization of the carrier collection to the photon incidence. We present a detailed prediction of the light-conversion efficiency of Si SNSCs based on finite-element simulation and thermodynamic balance analysis, with especially focusing on the comparison between SNSCs and film systems. Carrier losses due to radiative and Auger recombinations are introduced in the analysis of the limiting efficiency, which show that the Auger recombination plays a key role in accurately predicting the efficiency of Si SNSCs, otherwise, the device performance would be strongly overestimated. The study paves a more realistic way to evaluate the nanostructured solar cells based on indirect-band photoactive materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Degradation and recovery mechanisms in lithium-doped solar cells

Several groups of lithium-doped solar cells have been evaluated under 1-MeV electron irradiation. Many of these groups indicated superior electrical output after irradiation and recovery as compared to similarly irradiated n/p solar cells. The superior cells are those with lithium concentrations of 2 to 5 x 10 to the 14th power atoms per cu cm at the junction. An irradiation of lithium-doped cells with 28-MeV electrons indicated a tenfold advantage of lithium-doped cells over n/p cells. Studies of the changes in the lithium concentration during recovery have shown the amounts of lithium reacting is highly nonlinear in regard to the electron fluence and varies greatly with distance from the junction. The results indicate that precipitation of lithium on radiation defects may be the cause of recovery rather than ion pairing.

Downing, R. G.↗

Status of FEP encapsulated solar cell modules used in terrestrial applications

The Lewis Research Center has been engaged in transferring the FEP encapsulated solar cell technology developed for the space program to terrestrial applications. FEP encapsulated solar cell modules and arrays were designed and built expressly for terrestrial applications. Solar cell power systems were installed at three different land sites, while individual modules are undergoing marine environment tests. Four additional power systems are being completed for installation during the summer of 1974. These tests have revealed some minor problems which have been corrected. The results confirm the inherent utility of FEP encapsulated terrestrial solar cell systems.

Ratajczak, A. F.↗

Development and fabrication of a solar cell junction processing system

A processing system capable of producing solar cell junctions by ion implantation followed by pulsed electron beam annealing was developed and constructed. The machine was to be capable of processing 4-inch diameter single-crystal wafers at a rate of 10(7) wafers per year. A microcomputer-controlled pulsed electron beam annealer with a vacuum interlocked wafer transport system was designed, built and demonstrated to produce solar cell junctions on 4-inch wafers with an AMI efficiency of 12%. Experiments showed that a non-mass-analyzed (NMA) ion beam could implant 10 keV phosphorous dopant to form solar cell junctions which were equivalent to mass-analyzed implants. A NMA ion implanter, compatible with the pulsed electron beam annealer and wafer transport system was designed in detail but was not built because of program termination.

Source record↗

Carrier lifetimes of >1 μs in Sn-Pb perovskites enable efficient all-perovskite tandem solar cells

All-perovskite–based polycrystalline thin-film tandem solar cells have the potential to deliver efficiencies of >30%. However, the performance of all-perovskite–based tandem devices has been limited by the lack of high-efficiency, low–band gap tin-lead (Sn-Pb) mixed-perovskite solar cells (PSCs). We found that the addition of guanidinium thiocyanate (GuaSCN) resulted in marked improvements in the structural and optoelectronic properties of Sn-Pb mixed, low–band gap (~1.25 electron volt) perovskite films. The films have defect densities that are lower by a factor of 10, leading to carrier lifetimes of greater than 1 microsecond and diffusion lengths of 2.5 micrometers. These improved properties enable our demonstration of >20% efficient low–band gap PSCs. When combined with wider–band gap PSCs, we achieve 25% efficient four-terminal and 23.1% efficient two-terminal all-perovskite–based polycrystalline thin-film tandem solar cells.

14 SOLAR ENERGY↗

Mechanically-stacked tandem solar cells with GaAsP on GaP and silicon

Preliminary results are encouraging for the achievement of high conversion efficiencies using a GaAsP top solar cell mechanically stacked on a conventional silicon solar cell. A realistic maximum of 29.4 percent is suggested when both the top and bottom solar cells are state of the art. Practical system efficiencies greater than 25 percent are attainable in the near future with the use of a state of the art bottom solar cell.

Negley, Gerald H.↗

Lattice-mismatched In(0.40)Al(0.60)As window layers for indium phosphide solar cells

The efficiency of indium phosphide (InP) solar cells is limited by its high surface recombination velocity (approximately 10(exp 7) cm/s). This might be reduced by a wide-bandgap window layer. The performance of InP solar cells with wide-bandgap (1.8 eV) lattice-mismatched In(0.40)Al(0.60)As as a window layer was calculated. Because the required window layer thickness is less than the critical layer thickness, growth of strained (pseudomorphic) layers without interfacial misfit dislocations should be possible. Calculations using the PC-lD numerical code showed that the efficiencies of baseline and optimized p(+)n (p-on-n) cells are increased to more than 22 and 24 percent, (air mass zero (AMO), 25 C), respectively for a lattice-mismatched In(0.40)Al(0.60)As window layer of 10-nm thickness. Currently, most cell development work has been focused on n(+)p (n-on-p) structures although comparatively little improvement has been found for n(+)p cells.

Jain, Raj K.↗

Formation of a Secondary Phase in Thermally Evaporated MAPbI 3 and Its Effects on Solar Cell Performance

Thermal evaporation is a promising deposition technique to scale up perovskite solar cells (PSCs) to large areas, but the lack of understanding of the mechanisms that lead to high-quality evaporated methylammonium lead triiodide (MAPbI 3 ) films gives rise to devices with efficiencies lower than those obtained by spin coating. Here this work investigates the crystalline properties of MAPbI 3 deposited by the thermal coevaporation of PbI 2 and MAI, where the MAI evaporation rate is controlled by setting different temperatures for the MAI source and the PbI 2 deposition rate is controlled with a quartz crystal microbalance (QCM). Using grazing incident wide-angle X-ray scattering (GIWAXS) and X-ray diffraction (XRD), we identify the formation of a secondary orthorhombic phase (with a Pnma space group) that appears at MAI source temperatures below 155 °C. With synchrotron-based X-ray fluorescence (XRF) microscopy, we show that the changes in crystalline phases are not necessarily due to changes in stoichiometry. The films show a stochiometric composition when the MAI source is heated between 140 to 155 °C, and the samples become slightly MAI rich at 165 °C. Increasing the MAI temperature beyond 165 °C introduces an excess of MAI in the film, which promotes the formation of films with low crystallinity that contain low-dimensional perovskites. When they are incorporated in solar cells, the films deposited at 165 °C result in the champion power conversion efficiency, although the presence of a small amount of low-dimensional perovskite may lead to a lower open-circuit voltage. We hypothesize that the formation of secondary phases in evaporated films limits the performance of PSCs and that their formation can be suppressed by controlling the MAI source temperature, bringing the film toward a phase-pure tetragonal structure. Control of the phases during perovskite evaporation is therefore crucial to obtain high-performance solar cells.

36 MATERIALS SCIENCE↗

Investigation of the basic physics of high efficiency semiconductor hot carrier solar cell

The main purpose of this research program is to investigate potential semiconductor materials and their multi-band-gap MQW (multiple quantum wells) structures for high efficiency solar cells for aerospace and commercial applications. The absorption and PL (photoluminescence) spectra, the carrier dynamics, and band structures have been investigated for semiconductors of InP, GaP, GaInP, and InGaAsP/InP MQW structures, and for semiconductors of GaAs and AlGaAs by previous measurements. The barrier potential design criteria for achieving maximum energy conversion efficiency, and the resonant tunneling time as a function of barrier width in high efficiency MQW solar cell structures have also been investigated in the first two years. Based on previous carrier dynamics measurements and the time-dependent short circuit current density calculations, an InAs/InGaAs - InGaAs/GaAs - GaAs/AlGaAs MQW solar cell structure with 15 bandgaps has been designed. The absorption and PL spectra in InGaAsP/InP bulk and MQW structures were measured at room temperature and 77 K with different pump wavelength and intensity, to search for resonant states that may affect the solar cell activities. Time-resolved IR absorption for InGaAsP/InP bulk and MQW structures has been measured by femtosecond visible-pump and IR-probe absorption spectroscopy. This, with the absorption and PL measurements, will be helpful to understand the basic physics and device performance in multi-bandgap InAs/InGaAs - InGaAs/InP - InP/InGaP MQW solar cells. In particular, the lifetime of the photoexcited hot electrons is an important parameter for the device operation of InGaAsP/InP MQW solar cells working in the resonant tunneling conditions. Lastly, time evolution of the hot electron relaxation in GaAs has been measured in the temperature range of 4 K through 288 K using femtosecond pump-IR-probe absorption technique. The temperature dependence of the hot electron relaxation time in the X valley has been measured.

Alfano, R. R.↗

The Voltage Boost Enabled by Luminescence Extraction in Solar Cells

A new physical principle has emerged to produce record voltages and efficiencies in photovoltaic cells, 'luminescence extraction.' This is exemplified by the mantra 'a good solar cell should also be a good LED.' Luminescence extraction is the escape of internal photons out of the front surface of a solar cell. Basic thermodynamics says that the voltage boost should be related to concentration ratio, C, of a resource by ..delta..V=(kT/q)ln{C}. In light trapping, (i.e. when the solar cell is textured and has a perfect back mirror) the concentration ratio of photons C={4n2}, so one would expect a voltage boost of ..delta..V=kT ln{4n2} over a solar cell with no texture and zero back reflectivity, where n is the refractive index. Nevertheless, there has been ambiguity over the voltage benefit to be expected from perfect luminescence extraction. Do we gain an open circuit voltage boost of ..delta..V=(kT/q)ln{n2}, ..delta..V=(kT/q)ln{2n2}, or ..delta..V=(kT/q)ln{4n2}? What is responsible for this voltage ambiguity ..delta..V=(kT/q)ln{4}=36mVolts? We show that different results come about, depending on whether the photovoltaic cell is optically thin or thick to its internal luminescence. In realistic intermediate cases of optical thickness the voltage boost falls in between; ln{n2}q..delta..V/kT)<;ln{4n2}.

14 SOLAR ENERGY↗

Roles of Interfacial Tension in Regulating Internal Organization of Low Bandgap Polymer Bulk Heterojunction Solar Cells by Polymer Additives

The role of a tertiary polymer-based additive is investigated in increasing the efficiency of inverted low bandgap polymer:fullerene bulk heterojunction (BHJ) solar cells. Charge separation in polymer BHJ solar cells relies on the phase separation between electron accepting fullerene derivatives and photoactive polymers. Proper distribution of individual phases of suitable crystallinities within the active layer is a key factor for efficient charge transport/extraction and high photovoltaic performance. Here in this paper, it is demonstrated that the minor addition of a tertiary amorphous polymer, polystyrene (PS), with optimized molecular weights can increase the overall photovoltaic efficiency of poly[N-9-heptadecanyl-2,7-carbazole-alt-5,5-(4,7-di-2-thienyl-2,1,3-benzothiadiazole)]:phenyl-C 61 butyric acid methyl ester (PCDTBT:PCBM) inverted BHJ solar cells, through the interfacial-tension-driven increase in crystallinities of photoactive phases and redistribution of PCBM molecules away from the top hole-collecting anode interface. Complementary studies correlating polymer interfacial tension, blend internal structure, charge transport, and photovoltaic characteristics show that tertiary, high molecular-weight polymers can serve as effective additives for improving the performance of low bandgap polymer solar cells.

25 ENERGY STORAGE↗

Identification of some key parameters limiting the performance of high-efficiency silicon solar cells

This paper presents, for the first time, a detailed sensitivity analysis of key cell parameters on silicon-cell efficiency by incorporating advanced solar cell physics in a sophisticated numerical simulation program. It delineates the true physical barriers to obtaining a high-efficiency silicon solar cell. Specific parameters presently limiting cell efficiency are identified to be the minority carrier lifetime and the recombination velocities at the front and back surfaces. Practical cell efficiencies in the vicinity of 22 percent are estimated to be attainable by using good quality silicon crystal and substantially reducing surface recombination velocities.

Mokashi, Anant R.↗

Suppressed Deep Traps and Bandgap Fluctuations in Cu 2 CdSnS 4 Solar Cells with ≈8% Efficiency

The identification of performance-limiting factors is a crucial step in the development of solar cell technologies. Cu 2 ZnSn(S,Se) 4 -based solar cells have shown promising power conversion efficiencies in recent years, but their performance remains inferior compared to other thin-film solar cells. Moreover, the fundamental material characteristics that contribute to this inferior performance are unclear. In this paper, the performance-limiting role of deep-trap-level-inducing 2Cu Zn +Sn Zn defect clusters is revealed by comparing the defect formation energies and optoelectronic characteristics of Cu 2 ZnSnS 4 and Cu 2 CdSnS 4 . It is shown that these deleterious defect clusters can be suppressed by substituting Zn with Cd in a Cu-poor compositional region. The substitution of Zn with Cd also significantly reduces the bandgap fluctuations, despite the similarity in the formation energy of the Cu Zn +Zn Cu and Cu Cd +Cd Cu antisites. Detailed investigation of the Cu 2 CdSnS 4 series with varying Cu/[Cd+Sn] ratios highlights the importance of Cu-poor composition, presumably via the presence of V Cu , in improving the optoelectronic properties of the cation-substituted absorber. Finally, a 7.96% efficient Cu 2 CdSnS 4 solar cell is demonstrated, which shows the highest efficiency among fully cation-substituted absorbers based on Cu 2 ZnSnS 4 .

14 SOLAR ENERGY↗