Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Analytical techniques for the analysis of stall/spin flight test data

Analytical techniques for the analysis of stall/spin flight test data are reviewed by discussing (1) certain special flight instrumentation issues, (2) the mathematical modeling techniques, and (3) the analysis of post stall and spinning flight of general aviation airplanes. The angles of attack, sideslip, roll, pitch, and yaw are derived from measurements of angular velocity and linear acceleration. The key to the success of this approach is to simultaneously estimate both the biases in the instrumentation and the initial conditions. Techniques for determining stability derivatives from flight data are applied to angles of attack too high for stabilized flight. This practice greatly expands the range over which aerodynamic characteristics can be determined from flight test. Nonlinear terms in certain aerodynamic functions are shown to be valid by comparing them with the trends of results at different angles of attack. A very old technique of studying spins is extended and applied to some modern light airplanes. Airplanes for which the wing provides the dominant moments during spins, offer the possibility of linking spin characteristics to longitudinal data.

Taylor, L. W., Jr.↗

Kinematic properties of rotary-wing and fixed-wing aircraft in steady coordinated high-g turns

An analytical approach to the study of flight dynamics of aircraft operating in a high-angle-of-attack flight regime and of helicopters operating in extreme thrust conditions is presented. Steady coordinated high-g turns are used to establish the initial equilibrium flight conditions near stall angles of attack. The kinematic properties of the aircraft in steady coordinated turns are examined: in high-g turns, pitch rate (independent of the angle of attack) is of a much larger magnitude than roll and yaw rate; a substantial roll rate is found to develop in steep turns for all angles of attack; the angle of attack also has a significant effect on the pitch attitude, with decreasing influence as the normal load factor increases. The exact small disturbance equations of motion of the aircraft in general steady turns are also developed for application to both rotary-wing and fixed-wing aircraft in extreme conditions. These equations are in a first-order, vector-matrix format, and are thus compatible with many efficient software packages developed in modern system theory.

Chen, R. T. N.↗

Effect of Ice and Frost Formations on Drag of NACA 65(sub 1) -212 Airfoil for Various Modes of Thermal Ice Protection

The effects of primary and. runback icing and frost formations on the drag of an 8-foot-chord NACA 651-212 airfoil section were investigated over a range of angles of attack from 20 to 80 and airspeeds up to 260 miles per hour for icing conditions with liquid-water contents ranging from 0.25 to 1.4 grams per cubic meter and datum air temperatures of -30 to 30 F. The results showed that glaze-ice formations, either primary or runback, on the upper surface near the leading edge of the airfoil caused large and rapid increases in drag, especially at datum air temperatures approaching 32 F and in the presence of high rates of water catch. Ice formations at lower temperatures (rime ice) did not appreciably increase the drag coefficient over the initial (standard roughness) drag coefficient. Cyclic de-icing of the primary Ice formations on the airfoil leading-edge section permitted the drag coefficient to return almost to the bare airfoil drag value. Runback icing on the lower surface did not present a serious drag problem except when heavy spanwise ridges of runback ice occurred aft of the heatable area. Frost formations caused rapid and large increases in drag with incipient stalling of the airfoil.

Gray, V. H.↗

Effect of a part span variable inlet guide vane on TF34 fan performance

Experimental aerodynamic and performance data were obtained from a TF34 engine. Part span variable inlet guide vanes mounted in front of the fan on the TF34 engine were tested to demonstrate the feasibility of modulating air flow and thrust for vertical takeoff aircraft systems. The fan was mapped to stall for a range of speeds and variable inlet guide were settings. Modulated fan tip performance and unmodulated hub performance were evaluated with a without an extended fan bypass splitter. The effect of a crosswind distortion screen on performance was also evaluated.

Alvarez, J.↗

Comparison of two and three dimensional flow computations with laser anemometer measurements in a transonic compressor rotor

A procedure for using an efficient axisymmetric code to generate downstream pressure input for more costly Euler codes is discussed. Two and three dimensional inviscid solutions for the flow within a transonic axial compressor rotor at design speed are compared to laser anemometer measurements at maximum flow and near stall operating points. Computational details of the 2-D axisymmetric stream function solution and the 3-D full Euler solution are described. Relative Mach number contours, shock location, and shock strength as measured and as predicted by the 3-D code are compared. Downstream of the rotor the inviscid computations agree with each other but predict higher pressure ratios than those measured. Euler codes require a downstream pressure as input. Since that pressure controls the computed mass flow and shock system, it must be consistent with an inviscid solution.

Chima, R. V.↗

Performance of single-stage axial-flow transonic compressor with rotor and stator aspect ratios of 1.63 and 1.77, respectively, and with design pressure ratio of 2.05

The overall and blade-element performance of a transonic compressor stage is presented over the stable operating range for speeds from 50 to 100 percent of design. The stage was designed for a pressure ratio of 2.05 at a flow of 20.2 kg/sec and a tip speed of 455 m/sec. At design speed the rotor and stage achieved peak efficiencies of 0.849 and 0.831, respectively, at the minimum flow condition. The stage stall point occurred at a flow higher than the design flow.

Moore, R. D.↗

Computer modeling of fan-exit-splitter spacing effects on F100 response to distortion

The distortion response of the F100(3) engine was effected by the fan exit splitter configuration. The sensitivity for a proximate splitter fan is calculated to be slightly greater than a remote splitter configuration with identical airfoils. Predicted response was based upon a multiple segment parallel compressor Model modified to include a bypass ratio representation that effects the performance characteristics of the last rotor and intermediate case struts. The predicted distortion response required an accurate definition of row pre- and post-stall undistorted operation.

Shaw, M.↗

A two-degree-of-freedom flutter mount system with low damping for testing rigid wings at different angles of attack

A wind tunnel model mount system for conducting flutter research using a rigid wing was developed. The wing is attached to a splitter plate so that the two move as one rigid body. The splitter plate is supported away from the tunnel wall by a system of rods with fixed fixed and conditions. The rods flex in such a way that only pitch and plunge oscillations are permitted. At the tunnel wall the rods are attached to a remotely controlled turntable so that angle of attack can be varied. Wind tunnel data obtained by using the mount system are presented for a supercritical and a conventional airfoil. Both classical flutter and stall flutter data are presented.

Farmer, M. G.↗

X-29A for NTF wind-tunnel/flight correlations

Considerations and recommendations for correlation are given. Basic tunnel calibration prior to research and development tests is suggested. Areas of concentration include: wing cruise drag and drag rise, wing separation and stall, afterbody and base drag, propulsion effects, vortex flows, cavity flows, and excrescences.

Daforno, G.↗

Effects of wing-leading-edge modifications on a full-scale, low-wing general aviation airplane: Wind-tunnel investigation of high-angle-of-attack aerodynamic characteristics

Wing-leading-edge modifications included leading-edge droop and slat configurations having full-span, partial-span, or segmented arrangements. Other devices included wing-chord extensions, fences, and leading-edge stall strips. Good correlation was apparent between the results of wind-tunnel data and the results of flight tests, on the basis of autorotational stability criterion, for a wide range of wing-leading-edge modifications.

Newsom, W. A., Jr.↗

Holographic interferometry and tomography at Ames Research Center

A YAG laser holographic interferometer system and reconstruction laboratory for the Ames 2- by 2-Foot Transonic Wind Tunnel are discussed. This system provides dual plate and double pulse holography for quantitative and qualitative measurements, respectively. Interferometric measurements of two-dimensional airfoils and three-dimensional bodies of revolution for a tomography feasibility study were made. The two-dimensional work included supercritical airfoils, an oscillating airfoil undergoing dynamic stall, and a circulation control airfoil. The tomography experiments centered around hemispherical nose and tangent ogive models. In addition, the tomography work covered the development of a Fourier transform code for the retrieval of the three dimensional density distributions from the interferograms.

Lee, G.↗

Theoretical and experimental power from large horizontal-axis wind turbines

A method for calculating the output power from large horizontal-axis wind turbines is presented. Modifications to the airfoil characteristics and the momentum portion of classical blade element-momentum theory are given that improve correlation with measured data. Improvement is particularly evident at low tip-speed ratios where aerodynamic stall can occur as the blade experiences high angles of attack. Output power calculated using the modified theory is compared with measured data for several large wind turbines. These wind turbines range in size from the DOE/NASA 100 kW Mod-0 (38 m rotor diameter) to the 2000 kW Mod-1 (61 m rotor diameter). The calculated results are in good agreement with measured data from these machines.

Viterna, L. A.↗

An experimental study of the flow in a wing with a partial span drooped leading edge

The flow field produced by a low aspect ratio wing (AR = 3.0) with a partial span leading edge droop was investigated in a series of low speed wind tunnel tests (Reynolds number based on 17.8 cm chord = 560,000). Photographs were obtained of surface oil flow patterns over an angle of attack range of alpha = 0 to 29 deg. Flow field surveys of the partially stalled wing at alpha = 25 deg were completed using a hot-wire probe, a split-film probe and a Conrad probe. The flow field survey data was presented using a color video display. The data indicated regions of apparent reversed flow in the separation region behind the wing and indicated the general cross-sectional shape of the separated wake flow.

Winkelmann, A. E.↗

Characteristics of the flow in the annulus-wall region of an axial-flow compressor rotor blade passage

Three-dimensional characteristics of the mean velocity and turbulence structure in the annulus-wall region of a moderately loaded compressor rotor have been investigated experimentally by employing triaxial hot-wire probes. Results are presented which indicate that the flow within and downstream of the rotor passage is highly complex due to the interaction of the annulus-wall boundary layer, blade boundary layers, tip leakage flow, and passage secondary flow. An understanding of the reported viscous flow interactions is important for establishing improved aerodynamic design criteria and efficiency, for predicting noise levels, and for determining the stall, surge, vibration, and flutter characteristics of turbomachinery.

Davino, R. M.↗

Analysis of data from a wind tunnel investigation of a large-scale model of a highly maneuverable supersonic V/STOL fighter - STOL configuration

The surface pressure and thermal characteristics of a large-scale model of a highly maneuverable supersonic fighter with STOL capability are described. The 7.28 m span model is powered by two J-97 turbojets, operated at 9340 N thrust. It combines upper-surface and spanwise blowing to augment the lift characteristics over a wide angle-of-attack range. The most significant feature of the fighter's flow field is the leading edge vortex that forms at low alphas, grows stronger, and moves inboard as alpha is increased. Upper surface blowing enhanced the lift on the wing in both stalled and unstalled areas significantly, while generating only a modest aft shift in the center of pressure. Lift gains were greatest at high alphas and with the flap deflected. Spanwise blowing was most significant at angles-of-attack greater than 8 deg, when the jet strengthened the vortex. The 1100 F spanwise blowing jet mixed very rapidly with the wing flow field, creating a maximum temperature rise of only 300-350 F. A comparison of small-scale and large-scale model wing pressure characteristics showed similar trends created by upper surface blowing, while spanwise blowing characteristics differed considerably. Force data correlated well with semi-empirical predictions for gross thrust coefficients less than 1.0.

Falarski, M. D.↗

Alleviation of the subsonic pitch-up of delta wings

A 'pylon vortex generator' concept has been proposed for alleviating the subsonic pitch-up instability of highly swept supersonic-cruise wings. Fixed at a part-span location, this leading-edge device utilizes the lateral velocity component in the flow approaching the swept leading edge to generate a streamwise vortex, opposite in sense to the tip vortex. The vortex-induced downwash outboard of the device serves to control the leading-edge stall development in the wing-tip regions. Wind-tunnel results on 60-deg and 74-deg flat-plate delta wings are presented to illustrate the operation of the pylon vortex generator in modifying the spanwise leading-edge separation characteristics resulting in effective alleviation of the pitch-up.

Rao, D. M.↗

The use of differential pressure feedback in an automatic flight control system

A feasibility study has been performed to evaluate the performance of a system whereby a control surface is positioned with differential pressure as the feedback variable. Analogous to a position command system, the control surface is commanded to move until a certain differential pressure is achieved at a given point on the surface. Frequency response tests and theoretical considerations indicate that the pressure feedback transfer function is first order, with a break frequency up to 50 rad/sec. There exist applications to the outer loops of flight control systems as well. Stability augmentation, gust alleviation, and stall prevention appear to be possible by feeding back differential pressure across lifting and control surfaces.

Levy, D. W.↗

Analysis of general-aviation accidents using ATC radar records

It is pointed out that general aviation aircraft usually do not carry flight recorders, and in accident investigations the only available data may come from the Air Traffic Control (ATC) records. A description is presented of a technique for deriving time-histories of aircraft motions from ATC radar records. The employed procedure involves a smoothing of the raw radar data. The smoothed results, in combination with other available information (meteorological data and aircraft aerodynamic data) are used to derive the expanded set of motion time-histories. Applications of the considered analytical methods are related to different types of aircraft, such as light piston-props, executive jets, and commuter turboprops, as well as different accident situations, such as takeoff, climb-out, icing, and deep stall.

Wingrove, R. C.↗