Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Reusability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Payload operations control center network (POCCNET) systems definition phase study report

The results of the studies performed during the systems definition phase of POCCNET are presented. The concept of POCCNET as a system of standard POCCs is described and an analysis of system requirements is also included. Alternative systems concepts were evaluated as well as various methods for development of reliable reusable software. A number of POCC application areas, such as command management, on board computer support, and simulation were also studied. Other areas of investigation included the operation of POCCNET systems, the facility requirements and usage.

Desjardins, R.↗
NASA NTRS1978

Preliminary Concept, Specifications, and Requirements for a Zero-Gravity Combustion Facility for Spacelab

The preliminary concept, specifications, and requirements of a reusable zero gravity combustion facility (0-GCF) for use by experimenters aboard the spacelab payload of the space transportation system (STS) orbiter are described. The facility will be amenable to any mission of the STS orbiter in which a spacelab habitable segment and pallet segment are integral and for which orbital mission plans specify induced accelerations of 0.0001 g or less for sufficiently long periods so as not to impact experiment performance.

Dewitt, Richard L.↗
NASA NTRS1978

Solar power satellite system definition study. Part 3: Preferred concept system definition

A concise but complete system description for the preferred concept of the Solar Power Satellite System is presented. Significant selection decisions included the following: (1) single crystal silicon solar cells; (2) glass encapsulated solar cell blankets; (3) concentration ratio 1; (4) graphite composite materials for primary structure; (5) electric propulsion for attitude control; (6) klystron RF amplifier tubes for the transmitter; (7) one kilometer diameter transmitter with a design trans mission link output power of 5,000 megawatts; (8) construction in low earth orbit with self-powered transfer of satellite modules to geosynchronous orbit; and (9) two-stage winged fully reusable rocket vehicle for transportation to low earth orbit.

Source record↗
NASA NTRS1978

Breadboard wash water renovation system

A total wash water renovation system concept was developed for removing objectionable materials from spacecraft wash water in order to make the water reusable. The breadboard model system described provides for pretreatment with ferric chloride to remove soap by chemical precipitation, carbon adsorption to remove trace dissolved organics, and ion exchange for removal of dissolved salts. The entire system was put into continuous operation and carefully monitored to assess overall efficiency and equipment maintenance problems that could be expected in actual use. In addition, the capacity of the carbon adsorbers and the ion-exchange resin was calculated and taken into consideration in the final evaluation of the system adequacy. The product water produced was well within the Tentative Wash Water Standards with regard to total organic carbon, conductivity, urea content, sodium chloride content, color, odor, and clarity.

Source record↗
NASA NTRS1978

Applicability of the control configured design approach to advanced earth orbital transportation systems

The applicability of the control configured design approach (CCV) to advanced earth orbital transportation systems was studied. The baseline system investigated was fully reusable vertical take-off/horizontal landing single-stage-to-orbit vehicle and had mission requirements similar to the space shuttle orbiter. Technical analyses were made to determine aerodynamic, flight control and subsystem design characteristics. Figures of merit were assessed on vehicle dry weight and orbital payload. The results indicated that the major parameters for CCV designs are hypersonic trim, aft center of gravity, and control surface heating. Optimized CCV designs can be controllable and provide substantial payload gains over conventional non-CCV design vertical take-off vehicles.

Hepler, A. K.↗
NASA NTRS1977

Long Duration Exposure Facility - A unique mode of Shuttle utilization

The Long Duration Exposure Facility (LDEF) is a Shuttle-transported, reusable, essentially passive facility with accommodations for a wide variety of experiments which require a free-flying carrier for exposure in space. Specifically, the LDEF is tailored to provide low-cost accommodations for experiments which have modest requirements for electrical power and data systems, and for experiments which benefit from postflight laboratory investigations with the retrieved experiment hardware. Each experiment for LDEF will be totally self-contained in a tray. As the interface with the facility has been minimized, the LDEF experimenters will be freed from many of the requirements which have complicated development of space experiments in the past.

Kinard, W. H.↗
NASA NTRS1978

The effect of technology advancements on the comparative advantages of electric versus chemical propulsion for a large cargo orbit transfer vehicle

Techniques for sizing electrically or chemically propelled orbit transfer vehicles and analyzing fleet requirements are used in a comparative analysis of the two concepts for various levels of traffic to geosynchronous orbit. The vehicle masses, fuel requirements, and fleet sizes are determined and translated into launch vehicle payload requirements. Technology projections beyond normal growth are made and their effect on the comparative advantages of the concepts is determined. A preliminary cost analysis indicates that although electric propulsion greatly reduces launch vehicle requirements substantial improvements in the cost and reusability of power systems must occur to make an electrically propelled vehicle competitive.

Rehder, J. J.↗
NASA NTRS1978

LDEF/Shuttle capabilities for environmental testing in space

The Long Duration Exposure Facility (LDEF) is being developed to accommodate experiments which require a free-flying exposure in space and which benefit from postflight laboratory analysis of the retrieved experiment hardware. The first LDEF mission, which is planned for a 6- to 12-month stay in space is scheduled in the late 1970s during the Shuttle Orbital Flight Test Program. The LDEF is a simple reusable structure which is three-axis gravity gradient stabilized when free flying in space. The experiments on the LDEF are totally self-contained in trays mounted to the structure. After the LDEF is either revisited or retrieved by the Shuttle, the trays with experiments will be returned to the experimenters for postflight inspection. Attention is given to the fabrication of a second LDEF for a long-term mission planned in 1979, aspects of LDEF orbit life time, the radiation environment, questions of solar exposure, the thermal environment, and the vacuum (atomic particle) environment.

Clark, L. G.↗
NASA NTRS1978

Energy impact assessment of NASA's past, present, and future space launch vehicles

An approach to analyze the total energy required for overall support of space launch vehicles is outlined along with some of the basic data required for such analyses. Selected results obtained by using this approach are presented for various past (some are already phased out), present, and future NASA launch vehicles, including an estimate of the total annual energy required to support one projected NASA launch vehicle traffic model. The material presented is expected to give a better insight into the details of an energy impact analysis. Major conclusions are that: (1) for expendable launch vehicle systems, the energy required to manufacture hardware and support launch operations is most significant; (2) for totally reusable systems, the energy required to process/manufacture propellants and fluids is by far the most significant contributor; and (3) up to 1991, the projected highest annual energy requirement for the NASA launch vehicles does not constitute a significant energy impact relative to the nation's total energy needs.

Rice, E. E.↗
NASA NTRS1978

Space Shuttle SRM Ignition System

This paper presents the Space Shuttle SRM Ignition System, which consists of a large solid propellant main igniter, a small solid propellant initiating igniter and an electromechanical safety and arming device containing two NASA Standard Initiators and a B-KNO3 pyrotechnic booster charge. In development motors, the igniter also has a valve through which CO2 is injected for post-firing quench of the SRM. The igniter has redundant, testable seals at all pressurized joints and three major reusable components; the case, the adapter, and the S&A device. Two development problem areas are discussed. One problem area was transverse mode combustion instability in the main igniter with maximum amplitude of 340 psi peak-to-peak at a frequency of 1500 Hz, which was reduced by a propellant grain configuration change and a change from a 2% aluminum content propellant to a formulation containing 10% aluminum. The other problem area was an excessively rapid rise of thrust in the SRM, which was reduced by reducing the igniter mass flow rate. This mass flow rate reduction was accomplished by removing portions of the grain starpoints in the head end.

Bolieau, C. W.↗
NASA NTRS1978

Design and performance verification of a passive propellant management system

This paper describes the design and verification testing of a reusable passive propellant management system. The system was designed to acquire propellant in low- or zero-g environments and also retain this propellant under high axially directed accelerations that may be experienced during launch and orbit-to-orbit transfer. The system design requirements were established to satisfy generally the requirements for a large number of potential NASA and military applications, such as orbit-to-orbit shuttles and satellite vehicles. The resulting concept was a multicompartmented tank with independent surface tension acquisition channels in each compartment. The tank was designed to provide a minimum expulsion efficiency of 98 percent when subjected to the simultaneous conditions of acceleration, vibration, and outflow. The system design has the unique capability to demonstrate low-g performance in a 1-g test environment, and the test program summarized was structured around this capability.

Hess, D. A.↗
NASA NTRS1978

High performance dash-on-warning air mobile missile system

Because fixed missile bases have become increasingly vulnerable to strategic nuclear attack, an air-mobile missile system is proposed, whereby ICBMs can be launched from the hold of large subsonic aircraft following a missile-assisted supersonic dash of the aircraft to a safe distance from their base (about 50 n mi). Three major categories of vehicle design are presented: staged, which employs vertical take-off and a single solid rocket booster similar to that used on the Space Shuttle; unstaged, which employs vertical take-off and four internally-carried reusable liquid rocket engines; and alternative concepts, some using horizontal take-off with duct-burning afterburners. Attention is given to the economics of maintaining 200 ICBMs airborne during an alert (about $600 million for each fleet alert, exclusive of acquisition costs). The chief advantages of the system lie in its reduced vulnerability to suprise attack, because it can be launched on warning, and in the possibility for recall of the aircraft if the warning proves to be a false alarm.

Hague, D. S.↗
NASA NTRS1978

Potential SSME modifications to provide extended capabilities for future applications

Expendable launch vehicles will be phased out during the first years of shuttle operation and the payloads currently carried to orbit by these vehicles will be placed in low earth orbit by the reusable shuttle. In connection with limitations regarding the weight of the payload which can be launched by the Space Shuttle in its present form, approaches have been considered for increasing the payload capability of the Shuttle. Propulsion systems for Shuttle derived vehicles with larger payload capabilities have been studied. Such systems can potentially be obtained from modifications of the Space Shuttle Main Engine (SSME). Concepts based on modifications to the basic engine include an SSME-35 for low altitude operation with liquid rocket boosters and an SSME-150 for operation over the complete altitude range as might be required in a single-stage-to-orbit vehicle application. Another modification would provide operation with a hydrocarbon fuel instead of hydrogen.

Kirby, F. M.↗
NASA NTRS1978

The 25 kW power module - First step beyond the baseline STS

The backbone of the first reusable Space Transportation System (STS) is the Space Shuttle. The 25 kW Power Module is currently being defined by NASA as the first significant increment in capability beyond the baseline STS and is to be available for use in 1983. The Power Module is an orbit-based space system which will augment the capability of the Space Shuttle Orbiter to support Spacelab sortie missions and will provide a unique free-flying mode for a variety of payloads which require high capability, long duration, and man-tended operation. The Power Module will make it possible for the Space Shuttle Orbiter and Spacelab to remain on-orbit for periods of time significantly in excess of that provided by the baseline STS (7 days) without major penalty to the Shuttle and its payload.

Mordan, G. W.↗
NASA NTRS1974

Fibrous refractory composite insulation

Family of high-temperature, low-density refractory composite insulations made from aluminoborosilicate and silica fibers has insulating material with improved mechanical and thermal properties. Composition is useful for reusable heat-shield materials.

Goldstein, H. E.↗
NASA NTRS1976

OAST Space Theme Workshop. Volume 2: Theme summary. 6: Advanced transportation systems. A: Theme statement. B. 26 April 1976 presentation. C. Theme summary. D. Initiative actions

Technology requirements for an integrated space transportation system capability which will allow the nation to use space efficiently, reliably, and routinely in the years between 1985 and 2000 with a significant return on invested resources will build on the currently defined space transportation system using shuttle, the IUS, and the advanced upper stage such as the solar electric propulsion system. Contributing technologies should include those which support (1) total reusability with minimal refurbishment; (2) responsiveness to high launch rate requirements when operation and energy are the predominant recurring costs; and (3) maximum flexibility in operation between earth and LEO and between LEO and GEO. Initiatives undertaken to advance the heavy lift to launch vehicles, single stage to orbit vehicles, and orbit transfer vehicles are listed.

Source record↗
NASA NTRS1978

Formulation of consumables management models, executive summary

Future manned space programs that have increased launch frequencies and reusable systems require an implementation of new consumables and systems management techniques that relieve both the operations support personnel and flight crew activities. Analytical models and techniques were developed which consist of a Mission Planning Processor (MPP) with appropriate consumables data base, methods of recognizing potential constraint violations in both the planning and flight operations functions, and flight data files for storage/retrieval of information over extended periods interfacing with flight operations processors for monitoring of the actual flights. Consumables subsystems considered in the MPP were electrical power, environmental control and life support, propulsion, hydraulics and auxiliary power.

Torian, J. G.↗
NASA NTRS1974

Pilot cryo tunnel: Attachments, seals, and insulation

Several different tests are described which simulated the actual configuration of a cryogenic wind tunnel operating at pressures up to 5 atmospheres (507 kPa) and temperatures from -320 F (78K) to 120 F (322K) in order to determine compatible bolting, adequate sealing, and effective insulating materials. The evaluation of flange attachments (continuous threaded studs) considered bolting based on compatible flanges, attachment materials, and prescribed bolt elongations. Various types of seals and seal configurations were studied to determine suitability and reusability under the imposed pressure and temperature loadings. The temperature profile was established for several materials used for structural supports.

Wilson, J. F.↗