Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Permeability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Impact of humidity on gas transport in polybenzimidazole membranes

Polybenzimidazoles (PBIs) are promising materials for high temperature H 2 /CO 2 separation in applications such as steam reforming and pre-combustion carbon capture where significant amounts of water are often present. However, PBIs are hydrophilic, and the impact of humidity on PBI gas separation properties is relatively unexplored. Furthermore, opportunity exists to elucidate the interplay between plasticization, free volume, and gas transport in glassy polymer membranes such as PBIs. Here, this study investigates the effect of humidity on H 2 , O 2 , and CO 2 permeabilities at 35 °C in a commercial PBI and two sulfone-containing PBIs. Water uptake significantly reduces PBI gas permeabilities at low humidities due to competitive sorption and antiplasticization. At high humidities, plasticization increases the permeabilities of larger gases in more hydrophilic PBIs. Effective fractional free volumes evaluated from gas permeation data and previously reported water sorption and dilation data suggest water plasticizes PBIs by increasing accessible free volume via enhanced molecular dynamics rather than by creating new free volume cavities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Water and salt transport properties of pentiptycene-containing sulfonated polysulfones for desalination membrane applications

A series of pentiptycene-containing disulfonated polysulfone copolymers (PENT-BP) were synthesized via condensation polymerization. Water and salt transport properties (solubility, diffusivity and permeability) were characterized for acid-form membranes (PENT-BP(H)) and compared with triptycene-based sulfonated polysulfones (TRP-BP(H)) and a non-iptycene-containing 4,4'-biphenol-based series (BPS(H)) of polysulfones to investigate the effect of pentiptycene on membrane performance. At comparable water content, the PENT-BP(H) exhibited increased water and salt permeability due to the additional free volume introduced by the pentiptycene units. Enhanced water/salt permeability selectivity of PENT-BP(H) series was also observed due to a significantly higher diffusivity selectivity. At comparable water permeance (P w D ~ 8 X 10 -6 cm 2 /s), the salt rejection of PENT-BP (H) copolymers obtained from dead-end filtration reached 91–93% at 400 psi, higher than that of a corresponding BPS(H) series. This study suggests that incorporation of iptycene moieties into polymer backbone is an effective strategy to enhance desalination membrane performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Finely tuning the microporosity in phosphoric acid doped triptycene-containing polybenzimidazole membranes for highly permselective helium and hydrogen recovery

High-performance polymer membranes with well-defined microporosity and size-sieving ability are especially attractive for helium and hydrogen recovery. Here, in this study, we report novel macromolecular engineering of polybenzimidazole (PBI) membranes that integrate hierarchical triptycene units for high permeability and polyprotic acid doping for size sieving via controllable manipulation of microporous architecture. The triptycene moieties disrupt chain packing and introduce additional configurational free volume, leading to significantly boosted He and H 2 permeabilities compared to previously reported PBI membranes. The acid doping resulted in crosslinked PBI membranes via hydrogen bonding and proton transfer with dramatically enhanced gas selectivities. Via adjusting the H 3 PO 4 -doping level, triptycene-based polybenzimidazole (TPBI) composite membranes (TPBI-(H 3 PO 4 ) x ) exhibit the highest gas selectivities for He enrichment (i.e., α(He/CH 4 ) = 7052 ± 156) and H 2 purification (i.e., α(H 2 /CH 4 ) = 5128 ± 110) among existing polymeric gas separation membranes. Additionally, under mixed-gas conditions at 150 °C, the TPBI-(H 3 PO 4 ) 0.98 membrane displays a H 2 permeability of 46.7 Barrer and a H 2 /CO 2 selectivity of 16, far beyond the Robeson's 2008 upper bound for H 2 /CO 2 separation. The facile and diverse tunability and excellent gas separation performance make TPBI-(H 3 PO 4 ) x membranes highly attractive for helium and hydrogen separation.

42 ENGINEERING↗

Machine learning-guided discovery of polymer membranes for CO 2 separation with genetic algorithm

Designing polymer membranes with high gas permeability and selectivity is a difficult multi-task constrained problem due to the trade-off between these two properties. In this work, we present a machine learning (ML) driven genetic algorithm to tackle the design problem of polymer membranes for CO 2 separation from N 2 and O 2 . Using literature data of permeability for three gases, we constructed multiple ML models with different fingerprinting featurization schemes to predict gas permeabilities. Then, we employed a genetic algorithm to design new polymers and evaluated their performance using our ML models. We were able to identify new polymer membranes that are promising for both CO 2 /N 2 and CO 2 /O 2 separations. Further, the top discovered polymers are predicted to have high glass transition temperatures. Similarly, the pyridine functionality was found in ≈20% of the predicted polymers. This framework can be used to design polymers for any application involving constrained optimization. Finally, we outlined the challenges and opportunities with using ML guided data-driven inverse design of polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microporous pentiptycene-based polybenzimidazole membranes for high temperature H 2 /CO 2 separation

Separating H 2 from syngas at elevated temperatures (100–250 °C) have attracted significant attention in recent years as a means to reduce energy consumption and capital costs in precombustion carbon capture processes, such as those following steam reforming of natural gas or coal gasification. Polybenzimidazole (PBI), particularly m-PBI, has been reported as a leading membrane material for high-temperature H 2 /CO 2 separation. However, m-PBI exhibits extremely low H 2 permeability, even at high temperatures, which limits its productivity in H 2 /CO 2 separation applications. Here, to address this limitation, this work introduces a new pentiptycene-based polybenzimidazole (PPBI) featuring significantly enhanced H 2 permeability and attractive high-temperature H 2 /CO 2 separation performance, which stems from the unique configurational free volume elements introduced by pentiptycene moieties. Further tuning of the free volume architecture of PPBI films is achieved via acid doping with phosphoric acid (PA) or trans-aconitic acid (TaA), which introduces crosslinking among PPBI chains. Under mixed-gas environment (50/50 mol% H 2 /CO 2 ) at 180 °C, the acid-doped PPBI films exhibit a ∼230 % increase in H 2 /CO 2 selectivity compared to pristine PPBI film while maintaining high H 2 permeability that is nearly 500 % of m-PBI. These properties approach the predicted upper bound for membrane operating at 180 °C, highlighting its great potential for high-temperature H 2 /CO 2 separation.

Liu, Mengdi [University of Notre Dame, IN (United ↗

Porous Flow Modeling of Axial Gas Redistribution in Fragmented LWR Fuel Rods using MOOSE

Understanding how gas axially redistributes within fragmented fuel pellets is crucial for predicting the behavior of Light Water Reactor (LWR) fuel rods, particularly during transient and accidental scenarios. The time scale of this phenomenon plays a fundamental role in determining the progression and hazard of a Loss Of Coolant Accident (LOCA), especially when high burn-up fuel in a severe state of fragmentation is involved. Here, this study presents a Computational Fluid Dynamics (CFD) model developed within the Multiphysics Object-Oriented Simulation Environment (MOOSE) to predict the time-scale of plenum depressurization in Light-Water Reactor (LWR) fuel rods driven by axial gas transport through fragmented pellets. The model examines the effects of incorporating non-linearities in the friction term by comparing the results with experimental data. The experiment employed surrogate fuel rods containing pellets subjected to mechanical and/or thermal loadings to simulate various severity of cracking, and aimed at studying the influence of fuel conditions on axial gas redistribution. The results of this analysis indicate that under certain flow regime conditions - determined by the value of an equivalent Reynolds number - accounting for the non-linear friction term in Navier-Stokes equations guarantees better predictions for the time-scale of plenum depressurization. Also, the model enabled the simulation of the pressure decay by assigning distinct permeability values to each pellet instead of a single uniform value. Multiple simulations were run across all possible pellet position combinations, having each pellet assigned with values of permeability extracted from the experimental data. This allows to quantify the impact of the considering various non-uniform distributions of permeability on the dynamics of axial gas redistribution. The present work findings enhance the understanding of axial gas transport, and provide valuable insights for the integration of a model for predicting the axial gas redistribution during a LOCA scenario into the BISON fuel performance code.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Water absorption and shrinkage behaviour of early-age cement in wellbore annulus

Controlling cement shrinkage in a wellbore is well-known as being important in maintaining its integrity. Although numerous laboratory experiments on the water absorption and shrinkage behaviour of oil well cement have been reported in the past, such behaviour in the wellbore annulus with consideration of pore water migration from the surrounding formation has seldom been examined. In this study, using a cement shrinkage model calibrated against available experimental data, a coupled hydromechanical finite element analysis of a cement-formation model is conducted to simulate the water migration, absorption and shrinkage behaviour of early-age cement placed in the annulus of a wellbore. The objectives of this study are (i) to identify the threshold permeability value of the formation above which there is no longer a bottleneck for pore water to flow into the cement and (ii) to estimate a reasonable range of cement bulk shrinkage volume in wellbore annulus geometry. Results show that the threshold permeability of the formation would be around 0.1 mD for three different types of cement examined in this study: Class G cement, rapid setting (RS) cement and Schlumberger optimized particle size distribution (OPSD) technology cement. The bulk shrinkage volume varies from 0.01% to 2.4% depending on cement type and formation permeability (1 mD to 0.1 μD). Finally, the proposed methodology facilitates the simulation of water migration/absorption and shrinkage behaviour of well cement in different formations.

02 PETROLEUM↗

Characterization of shale using Helium and Argon at high pressures

In order to estimate the shale gas in place and the eventual recovery during shale gas operations, one of the key requirements is to accurately characterize the shale’s petrophysical and transport properties such as porosity, permeability, diffusivity, and storage capacity. Despite the many efforts reported in the technical literature aiming to provide an improved understanding of the complex pore structures and the associated fluid flow in gas shales, complete characterization of organic-rich shale samples still poses a big challenge. Here, we have characterized mass transfer and sorption in shale at different length scales using Helium (He) and Argon (Ar) as probe gases. Thermogravimetric analysis (TGA) with a shale cube of ~1 cm 3 in size and gas expansion experiments with a full-diameter core (3.5” in diameter) were used to measure sorption kinetics/isotherms and mass transfer, respectively. Both samples are from the same depth/location in the Marcellus shale formation. The TGA steady-state technique was initially used to generate excess sorption isotherms for Ar, while dynamic TGA experiments were used to study its sorption kinetics. The TGA experiments demonstrate that Ar, which has a similar sorption potential as Methane, but is generally assumed to be inert, adsorbs onto the surfaces of the mesoporous and microporous regions of the shale samples according to a Langmuir-type behavior. Helium expansion experiments, on the full-diameter core, were used to measure the overall porosity, on the basis that He is a non-sorbing and inert gas as compared to Ar. The He expansion experiments, furthermore, allow us to delineate the mass transfer of gas across the inherent hierarchy of pore sizes, including macropores (macro- and microcracks), mesopores and micropores. Similar expansion experiments were also performed with Ar to study the combined impact of mass transfer and sorption. A triple-porosity model (TPM) was utilized to interpret the He expansion experiments with the shale core and to extract (estimate) relevant transport parameters. We report and compare here the diffusivities and permeabilities of the whole core for both He and Ar, as calculated from the modeling and fitting of the experimental data. On the premise that the shale cube is representative of the matrix region of the core, the Ar sorption kinetics from the cube experiments were subsequently combined with the transport parameters extracted from the He experiments to predict the behavior of the Ar expansion test with the full-diameter core. An excellent agreement is observed between the model predictions and the experimental data. The experimental observations and their interpretation indicate that one must be cautious when using Ar to estimate the true porosity and permeability of shales. In addition, we demonstrate that He and Ar probe gases, when used in tandem, can be employed effectively as a tool to characterize shales in terms of mass transfer and sorption dynamics across scales.

04 OIL SHALES AND TAR SANDS↗

Polybenzimidazole based random copolymers containing hexafluoroisopropylidene functional groups for gas separations at elevated temperatures

Polybenzimidazoles (PBIs) are attractive membrane materials for H 2 /CO 2 separation at hydrocarbon fuel derived synthesis gas operating conditions due to their exceptional physicochemical stability and promising permselectivity character. PBI molecular structure modification is a viable approach to disrupt chain packing altering the free-volume architecture which results in improved gas transport characteristics. This work is focused on the synthesis and characterization of novel PBI random copolymers for application as elevated temperature H 2 /CO 2 membranes. The co-polymerization route is expected to result in tailorable permeability and selectivity by combining the high H 2 permeability aspect of the highly disrupted loosely packed hexafluoroisopropylidene diphenyl group containing PBI segments (6F-PBI) with the highly selective tightly packed phenylene group containing PBI segments (m-PBI). 6F/m-PBI copolymers with varying 6F-PBI and m-PBI ratios having high inherent viscosity were synthesized. The structure and ratio of the 6F- and m-PBI fractions were confirmed using FTIR and NMR spectroscopic techniques. The measured gas transport properties of copolymer thin films cast in controlled environment were measured as a function of the operating conditions. Lastly, the H 2 permeability increased while H 2 /CO 2 selectivity decreased as the 6F-PBI copolymer fraction was increased.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tuning gas separation performance of polyimide membranes with macrocyclic crown ether units

Membrane-based gas separation is an energy-efficient alternative to conventional thermally-driven separation processes. However, polymer membranes face the permeability-selectivity trade-off challenge, which stems from the broad size distribution of free volume voids. Here, this study reports a molecular design strategy to address this challenge through incorporating macrocyclic crown ether (CE) moieties into the backbone of Matrimid® polyimide, a commercial gas separation membrane. A series of CE-containing Matrimid®-like copolyimides were synthesized with systematically varied CE molar contents ranging from 3 to 20%. These copolyimides formed ductile, defect-free thin films suitable for membrane fabrication. Gas permeation tests revealed a non-monotonic relationship between permeability/selectivity and CE content. Notably, the copolyimide with only 5% CE demonstrated a 61% increase in CO 2 /CH 4 selectivity and a 13% increase in CO 2 permeability relative to pristine Matrimid®. Higher CE contents did not yield further performance improvements, which is likely due to the competing effects of chain packing disruption and π–π interactions among CE moieties at high content. This hypothesis was supported by wide-angle X-ray scattering (WAXS) analysis, density measurements, and fractional free volume calculations. These findings highlight the potential of macrocyclic crown ether incorporation strategies in fine tuning the microstructure of commercial polyimide gas separation membranes to surpass the traditional permeability-selectivity trade-off.

CO2 separation↗

Virtual bound states elements and their effects on magnetic and electrical properties of Fe-Ni based metal amorphous nanocomposites

Metal amorphous nanocomposite alloys, with compositions (Fe 70 Ni 30 ) 80-x Nb 4 Si 2 B 14 TE x (0 ≤ x ≤ 5), where TE is a transition element, and (Fe 70 Ni 30 ) 80-y Nb 4+y Si 2 B 14 (0.5 ≤ y ≤ 2) were synthesized. Samples were annealed at 440 °C and strain-annealed at 440 °C and 300 MPa. Resistivity was found to increase with small substitutions of TE elements. Increasing V resulted in reduced B s from 1.2 T to 0.5 T. Further Mo additions lowered B s to 0.6 T, and consistently reduced the permeability. For Cr and Nb, resistivity increased, and strain-annealed permeability was lower than the annealed permeability. Finally, toroidal core losses on (Fe 70 Ni 30 ) 79.5 Nb 4 Si 2 B 14 V 1 yielded W1.0/400 = 2.1 W/kg, and W1.0/1 k = 6.0 W/kg.

36 MATERIALS SCIENCE↗

Safety evaluation of dermal exposure to phthalates: Metabolism-dependent percutaneous absorption

Phthalates, known as reproductive toxicants and endocrine disruptors, are widely used as plasticizers in polyvinyl chloride products. The present study was conducted for risk identification of dermal exposure to phthalates. When dibutyl phthalate was applied to the skin of hairless rats and humans, only monobutyl phthalate appeared through the skin, and the permeability of the skin was higher than that after the application of the monoester directly. The inhibition of skin esterases made the skin impermeable to the metabolite following dermal exposure to dibutyl ester, whereas removal of the stratum corneum from the skin did not change the skin permeation behavior. Similar phenomena were observed for benzyl butyl phthalate. The skin permeability of monobenzyl phthalate was higher than that of monobutyl phthalate in humans, although the reverse was observed in rats. Species difference in skin permeation profile corresponded to the esterase activity of the skin homogenate. Di(2-ethylhexyl) phthalate, which was not metabolized by esterases in the skin, was not transported across the skin. These results suggest that highly lipophilic phthalates may be transported easily across the stratum corneum lipids. The water-rich viable layer may become permeable to these phthalates by their metabolism into monoesters, which are relatively hydrophilic. Skin metabolism is essential to the percutaneous absorption of phthalates. Because esterase activity has large inter-individual differences, further study will be needed for individual risk identification of dermal exposure to phthalates. - Highlights: • Monophthalate, permeated through the skin after diphthalate application. • Characteristics of human skin cannot be determined from those of rat skin. • An accurate estimation of esterase activity in the skin requires a risk assessment.

60 APPLIED LIFE SCIENCES↗

Chemical and Reactive Transport Processes Associated with Hydraulic Fracturing of Unconventional Oil/Gas Shales

Hydraulic fracturing of unconventional oil/gas shales has changed the energy landscape of the U.S.. Recovery of hydrocarbons from tight, hydraulically fractured shales is a highly inefficient process, with estimated recoveries of < 25% for natural gas and < 5% for oil. This review focuses on the complex chemical interactions of additives in hydraulic fracturing fluid (HFF) with minerals and organic matter in oil/gas shales. These interactions are intended to increase hydrocarbon recovery by increasing porosities and permeabilities of tight shales. However, fluid-shale interactions result in the dissolution of shale minerals and the release and transport of chemical components. They also result in mineral precipitation in the shale matrix, which can reduce permeability, porosity, and hydrocarbon recovery. Competition between mineral dissolution and mineral precipitation processes influences the amounts of oil and gas recovered. We review the temporal/spatial origins and distribution of unconventional oil/gas shales from mudstones and shales, followed by discussion of their global and U.S. distributions and compositional differences from different U.S. sedimentary basins. We discuss the major types of chemical additives in HFF with their intended purposes, including drilling muds. Fracture distribution, porosity, permeability, and the identity and molecular-level speciation of minerals and organic matter in oil/gas shales throughout the hydraulic fracturing process are discussed. Also discussed are analysis methods used in characterizing oil/gas shales before and after hydraulic fracturing, including permeametry and porosimetry measurements, X-ray diffraction/Rietveld refinement, X-ray computed tomography, scanning/transmission electron microscopy, and laboratory- and synchrotron-based imaging/spectroscopic methods. Reactive transport and spatial scaling are discussed in some detail in order to relate fundamental molecular-scale processes to fluid transport. Furthermore, our review concludes with a discussion of potential environmental impacts of hydraulic fracturing and important knowledge gaps that must be bridged to achieve improved mechanistic understanding of fluid transport in oil/gas shales.

04 OIL SHALES AND TAR SANDS↗

Impact of Acid–Base Stimulation Sequence on Mineral Stability for Tight/Impermeable Unconventional Carbonate-Rich Rocks: A Delaware Basin Case Study

We report mineral precipitation due to reactions with injected fluids during unconventional fracture stimulation is a well-recognized problem. The goal of this study is to evaluate secondary mineral precipitation and permeability attenuation under chemical injection scenarios specific to the Delaware basin. Whole cylindrical cores (2.54 cm diameter and 2.54 cm height) and ground shale (150–250 μm) from the carbonate-rich Bone Spring Formation, Delaware Basin TX (Leonardian), were reacted at 80 °C and 85 bar using a hydraulic fracturing fluid (HFF) recipe and an injection sequence typical of the Delaware Basin. The reacted shales and solutions were analyzed using a variety of laboratory- and synchrotron-based techniques to characterize both the chemical and spatial distributions of secondary mineral precipitation and identify changes in permeability and mineralogy. This carbonate-rich shale (>84% calcite) rapidly neutralized the acidic HFF. Synchrotron-based X-ray fluorescence mapping coupled with X-ray absorption spectroscopy (both bulk and micro) showed that most of the iron was in an oxidized form prior to exposure to HFF and that almost all iron(II) became fully oxidized after the reaction. Scanning electron microscopy images of the ground shale samples primarily identified iron(oxyhydr)oxide microcrystals on grain surfaces. A few small isolated iron-rich areas also contained sulfur, suggesting that some pyrite was preserved when isolated within a calcite crystal but that most was oxidized. The rapid neutralization of the acid spearhead in these carbonate-rich samples demonstrates that the acid spearhead is useful for initiating fractures in extremely calcite-rich rocks but does little to enhance rock permeability. This suggests that the impact of the acid spearhead is significantly smaller for carbonate-rich shales compared to clay-rich shales, which has broad implications for acidizing in carbonate-rich shale formations and iron transformations within these shales.

58 GEOSCIENCES↗

Mobility of Radionuclides in Fractured Carbonate Rocks: Lessons from a Field-Scale Transport Experiment

Current research on radionuclide disposal is mostly conducted in granite, clay, saltstone, or volcanic tuff formations. These rock types are not always available to host a geological repository in every nuclear waste-generating country, but carbonate rocks may serve as a potential alternative. To assess their feasibility, a forced gradient cross-borehole tracer experiment was conducted in a saturated fractured chalk formation. The mobility of stable Sr and Cs (as analogs for their radioactive counterparts), Ce (an actinide analog), Re (a Tc analog), bentonite particles, and fluorescent dye tracers through the flow path was analyzed. The migration of each of these radionuclide analogs (RAs) was shown to be dependent upon their chemical speciation in solution, their interactions with bentonite, and their sorption potential to the chalk rock matrix. The brackish groundwater resulted in flocculation and immobilization of most particulate RAs. Nevertheless, the high permeability of the fracture system allowed for fast overall transport times of all aqueous RAs investigated. This study suggests that the geochemical properties of carbonate rocks may provide suitable conditions for certain types of radionuclide storage (in particular, brackish, high-porosity, and low-permeability chalks). Nevertheless, careful consideration should be given to high-permeability fracture networks that may result in high radionuclide mobility.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Wellbore Cement Porosity Evolution in Response to Mineral Alteration during CO 2 Flooding

Mineral reactions during CO 2 sequestration will change the pore-size distribution and pore surface characteristics, complicating permeability and storage security predictions. In this study, we report a small/wide angle scattering study of wellbore cement that has been exposed to carbon dioxide for three decades. We have constructed detailed contour maps that describe local porosity distributions and the mineralogy of the sample and relate these quantities to the carbon dioxide reaction front on the cement. We find that the initial bimodal distribution of pores in the cement, 1–2 and 10–20 nm, is affected differently during the course of carbonation reactions. Initial dissolution of cement phases occurs in the 10–20 nm pores and leads to the development of new pore spaces that are eventually sealed by CaCO 3 precipitation, leading to a loss of gel and capillary nanopores, smoother pore surfaces, and reduced porosity. This suggests that during extensive carbonation of wellbore cement, the cement becomes less permeable because of carbonate mineral precipitation within the pore space. Additionally, the loss of gel and capillary nanoporosities will reduce the reactivity of cement with CO 2 due to reactive surface area loss. Finally, this work demonstrates the importance of understanding not only changes in total porosity but also how the distribution of porosity evolves with reaction that affects permeability.

54 ENVIRONMENTAL SCIENCES↗

Impact of Chemical and Mechanical Processes on Leakage from Damaged Wells in CO 2 Storage Sites

The perceived risk of CO 2 leakage through wells has been considered a potential limitation to commercial scale deployment of geologic CO 2 storage. However, chemical and mechanical alteration of cement can reduce the permeability of leakage pathways. We conducted 100s of simulations spanning realistic operating conditions and well-damage characteristics to understand (1) under what conditions and time frames do fractures seal and (2) for fractures that do not seal, how quickly and to what extent is the permeability reduced. For the conditions simulated, fractures with apertures in the tens of microns seal while those greater than hundreds of microns may exhibit long-term leakage. Fractures with apertures between 10 and 500 μm took a few days to a couple of years to seal. For non-sealing fractures mechanical deformation of altered asperities can rapidly reduce permeability. Here, a sealing criterion was developed to relate fracture aperture with the cemented length required for self-sealing. Longer cemented intervals can seal large fractures; however, they take longer to seal and leak larger volumes before sealing. While the results presented here are subject to uncertainties, the manuscript provides a framework in which a model can be used to quantitatively answer questions regarding well integrity to facilitate decision making.

58 GEOSCIENCES↗

Molecular Dynamics Simulation Study of the Protonation State Dependence of Glutamic Acid Transport through a Cyclic Peptide Nanotube

The effect of the protonation state of glutamic acid on its translocation through cyclic peptide nanotubes (CPNs) was assessed by using molecular dynamics (MD) simulations. Anionic (GLU–), neutral zwitterionic (GLU0), and cationic (GLU+) forms of glutamic acid were selected as three different protonation states for an analysis of energetics and diffusivity for acid transport across a cyclic decapeptide nanotube. Based on the solubility-diffusion model, permeability coefficients for the three protonation states of the acid were calculated and compared with experimental results for CPN-mediated glutamate transport through CPNs. Potential of mean force (PMF) calculations reveal that, due to the cation-selective nature of the lumen of CPNs, GLU–, so-called glutamate, shows significantly high free energy barriers, while GLU+ displays deep energy wells and GLU0 has mild free energy barriers and wells inside the CPN. The considerable energy barriers for GLU– inside CPNs are mainly attributed to unfavorable interactions with DMPC bilayers and CPNs and are reduced by favorable interactions with channel water molecules through attractive electrostatic interactions and hydrogen bonding. Unlike the distinct PMF curves, position-dependent diffusion coefficient profiles exhibit comparable frictional behaviors regardless of the charge status of three protonation states due to similar confined environments imposed by the lumen of the CPN. The calculated permeability coefficients for the three protonation states clearly demonstrate that glutamic acid has a strong protonation state dependence for its transport through CPNs, as determined by the energetics rather than the diffusivity of the protonation state. In addition, the permeability coefficients also imply that GLU– is unlikely to pass through a CPN due to the high energy barriers inside the CPN, which is in disagreement with experimental measurements, where a considerable amount of glutamate permeating through the CPN was detected. To resolve the discrepancy between this work and the experimental observations, several possibilities are proposed, including a large concentration gradient of glutamate between the inside and outside of lipid vesicles and bilayers in the experiments, the glutamate activity difference between our MD simulations and experiments, an overestimation of energy barriers due to the artifacts imposed in MD simulations, and/or finally a transformation of the protonation state from GLU– to GLU0 to reduce the energy barriers. Altogether, our study demonstrates that the protonation state of glutamic acid has a strong effect on the transport of the acid and suggests a possible protonation state change for glutamate permeating through CPNs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗