Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OIL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Oil Production by a Consortium of Oleaginous Microorganisms grown on primary effluent wastewater

Municipal wastewater could be a potential growth medium that has not been considered for cultivating oleaginous microorganisms. This study is designed to determine if a consortium of oleaginous microorganism can successfully compete for carbon and other nutrients with the indigenous microorganisms contained in primary effluent wastewater. RESULTS: The oleaginous consortium inoculated with indigenous microorganisms reached stationary phase within 24 h, reaching a maximum cell concentration of 0.58 g L -1. Water quality post-oleaginous consortium growth reached a maximum chemical oxygen demand (COD) reduction of approximately 81%, supporting the consumption of the glucose within 8 h. The oleaginous consortium increased the amount of oil produced per gram by 13% compared with indigenous microorganisms in raw wastewater. Quantitative polymerase chain reaction (qPCR) results show a substantial population increase in bacteria within the first 24 h when the consortium is inoculated into raw wastewater. This result, along with the fatty acid methyl esters (FAMEs) results, suggests that conditions tested were not sufficient for the oleaginous consortium to compete with the indigenous microorganisms.

Bio-fuel, Municipal wastewater, Oleaginous microor↗

Flaxseed oil ameliorates aging in d ‐galactose induced rats via altering gut microbiota and mitigating oxidative damage

Abstract BACKGROUND Aging causes decreased antioxidant capacity and chronic inflammation and may even elevate cancer risks. Previous studies reported that flaxseed oil (FO) can alleviate age‐related diseases, including improving alcoholic liver disease, atherosclerosis and diabetes. However, whether the intestinal microbiota accountable for this alleviation is still unknown. This study aims to study the antioxidant effects of FO in an aging rat model and the underlying mechanism between the intestinal microbiota and aging. RESULTS Our results presented that serum and liver antioxidant capacities in FO group were up‐regulated, and liver inflammation in FO group was reduced. The 16S rDNA sequencing showed that FO regulated the microbial community, including up‐regulation of four families of Lactobacillus and six families of Clostridium. In addition, FO had also adjusted the relative abundance of several genera such as Ruminococcaceae_UCG‐005 and Prevotella_9 , which may be the key bacteria associated with the aging process. Colonic transcriptome analysis showed that there were 1679 differentially expressed genes (DEGs) in the Model group and the FO group (134 up‐regulated and 1545 down‐regulated). Gene set enrichment analysis (GSEA) revealed FO down‐regulates the expression of the upstream genes Ptprc , Lck , Zap70 , Lat and Lcp2 in the T cell receptor signaling pathway. CONCLUSION In conclusion, FO improved antioxidant capacity and reduced intestinal microbial disturbances caused by aging damage, indicating that dietary FO has the potential to fight aging damage. This study provides a more comprehensive view of dietary intervention to improve aging. © 2022 Society of Chemical Industry.

Sun, Xiaoyan↗

Microbial communities and biogeochemical functioning across peatlands in the Athabasca Oil Sands region of Canada: Implications for reclamation and management

Abstract Peatlands play an important role in global biogeochemical cycles and are essential for multiple ecosystem functions. Understanding the environmental drivers of microbial functioning and community structure can provide insights to enable effective and evidence‐based management. However, it remains largely unknown how microbial diversity contributes to the functioning of belowground processes. Addressing this gap in knowledge will provide a better understanding of microbial‐mediated processes in peatlands that are undergoing restoration or reclamation. This study assessed the changes in microbial community diversity and structure as well as soil function by measuring microbial respiration on a range of substrates from three natural fen types found in the Athabasca Oil Sands region of Alberta, Canada (a poor fen, a hypersaline fen, and a tree‐rich fen) and a nearby constructed fen undergoing reclamation following open pit mining. Overall, substrate induced respiration was significantly higher in the constructed fen. Alpha diversity of fungi and prokaryotes was highest in the tree‐rich fen, and the composition of microbial communities was significantly different between fens. Both fungal and prokaryotic communities were strongly related to pore water pH and temperature, with plant richness also contributing to the shape of fungal communities. In summary, microbial community structure reflects the underlying differences in soil condition across different fens but plays essential roles in the ecological functions of soil. These findings provide a new outlook for the management of peatlands undergoing post‐mining reclamation. Future research on peatland reclamation should consider the dynamic interaction between communities and ecosystem functionality, for which this study forms a useful baseline.

54 ENVIRONMENTAL SCIENCES↗

Ordering Polymer‐Grafted Nanoparticles at Oil–Air Interfaces under Magnetic Fields

Abstract Polymer‐grafted magnetic nanoparticles at oil–air interfaces are examined to reveal the role of chain length and anisotropy on particle packing order in thin films. It is found that particles grafted with intermediate chain lengths and sparse grafting densities exhibit enhanced packing order with increasing magnetic field strength. Voronoi tessellation results present an increase in the cell area distribution of these samples, suggesting that chain conformations are affected. For the longest graft length, particles become more disordered under magnetic fields. It is proposed that fluctuations in the bridged chains rearrange particles into less ordered packing with field application and the mechanism of packing order differs for varying graft chain lengths. Grafting anisotropy is found to determine the spatial nanoparticle organization in assembled monolayers.

Liu, Siqi↗

Bio‐Based Piezo‐ and Thermoresistive Photocurable Sensing Materials from Acrylated Epoxidized Soybean Oil

Abstract Bio‐based photocurable polymers are increasingly in demand as environmentally friendly materials for advanced applications. Together with functional fillers, these represent a next step for the generation of functional and active smart materials, compatible with additive manufacturing technologies. Herein, acrylated epoxidized soybean oil (AESO) mixed with different amounts of reduced graphene oxide (rGO) up to 6 wt% in order to obtain UV‐curable piezoresistive and thermoresistive materials, is reported. It is shown that the addition of rGO to AESO hinders the curing process, but always maintains double bond conversions higher than 50%. Composites are characterized by a good dispersion of micrometric filler clusters. Further, the thermal stabilities are close to 300 °C and crosslinking degrees are above 1.75 mmol cm –3 . The Young modulus of the composites decreases with the addition of the rGO fillers, in particular for the higher filler contents, and electrical conductivities up to 0.13 S m –1 are obtained for the composites with the highest rGO content. UV‐curable composites with piezoresistive and thermoresistive responses suitable for applications are thus obtained, characterized by gauge factors around 26 for deformations up to 2% and maximum thermoresistive sensitivity of S = 0.43, values similar to the values obtained for petroleum‐based materials.

Mendes‐Felipe, Cristian↗

Coconut oil derived five‐component synthetic oviposition deterrent for oriental fruit fly, Bactrocera dorsalis

Abstract BACKGROUND Bactrocera dorsalis, oriental fruit fly (OFF), is one of the most destructive agricultural pests. Although bait sprays can effectively control OFF,resistance development has been a concern. We evaluated the oviposition deterrent activity of coconut free fatty acids (CFFA), a mixture of eight coconut oil‐derived fatty acids known to repel hematophagous insects and deter their feeding and oviposition, against OFF females. RESULTS In laboratory 72‐h two‐choice assays using guava‐juice infused‐agar as an oviposition substrate, CFFA deterred OFF oviposition in a dose‐dependent manner with the greatest reduction of 87% at 20 mg dose compared to the control. When the eight CFFA components were tested individually, four compounds (caprylic, capric, oleic, and linoleic acids) significantly reduced OFF oviposition (‘negative‐compounds’), two (lauric and myristic acids) had no effect (‘neutral‐compounds’), and two (palmitic and stearic acids) stimulated OFF oviposition (‘positive‐compounds’). In two‐choice tests, the ‘negative‐compounds’ blend failed to elicit the same level of oviposition reduction as CFFA at equivalent concentrations found in CFFA. Adding the two ‘neutral‐compounds’ recovered the oviposition deterrence similar to CFFA. Subsequent subtraction tests showed that four ‘negative‐compounds’ plus lauric acid was as effective as CFFA in reducing OFF oviposition in guava‐juice agar. This five‐component key‐deterrent blend also reduced OFF oviposition by 95 and 72% on papaya and tomato fruit, respectively. CONCLUSION CFFA acts as an oviposition deterrent for OFF. Given that CFFA compounds are generally regarded as safe for humans and the environment, CFFA and its bioactive components have potential use in behavioral control strategies against OFF. © 2023 Society of Chemical Industry. This article has been contributed to by U.S. Government employees and their work is in the public domain in the USA.

Agriculture↗

Long-Term Effects of Crude Oil Spillage on Selected Physicochemical Properties Including Heavy Metal Contents of Sandy Tropical Soil

Crude oil spillage effects on the environment often wane with time, making late remediation of affected soils look irrelevant. Physicochemical quality of a sandy soil under 9-year-old spillage was compared with that of adjacent unaffected site in southern Nigeria. Soil bulk density and equilibrated water content were higher in affected than unaffected site, but permeability did not change. The spillage increased soil pH, organic carbon, total nitrogen and available phosphorus by about 7%, 1700%, 133% and − 16%, respectively. It lowered divalent exchangeable bases/acidity but raised base saturation. It increased total petroleum hydrocarbon (PHC{sub t}) and micronutrients/heavy metals (Fe, Mn, Zn, Cd and Pb), all of which were below their critical limits in soils by regulatory bodies. Soil pH, organic carbon and PHC{sub t} correlated positively with all five micronutrients/heavy metals; total nitrogen did so with Zn and Pb. Nine-year period may be insufficient for spillage effects in sandy soils to cease to be evident. Such effects for PHC{sub t} and heavy metals, however, are deemed tolerable for ecological safety.

54 ENVIRONMENTAL SCIENCES↗

Research on the Mechanism and Kinetics of Oil-Product Adsorption from Industrial Wastewater by a Modified Hydrophobic Carbonate Sludge

Features of dissolved oil-product adsorption from industrial wastewater by a modified hydrophobic carbonate sludge are studied. The adsorption isotherm is obtained. The adsorption mechanism on the new sorbent is investigated as physical unactivated adsorption using thermodynamic and kinetic parameters. The Gibbs free energy (–(20.26–21.46) kJ/mol), isosteric heat of adsorption (0.9–1.17 kJ/mol), adsorption rate constants ((0.2–0.47)·10{sup –3}sec{sup –1}), and apparent activation energy (6.6–28.6 kJ/mol) are calculated. Adsorption under dynamic conditions is studied.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chromatographic isolation of vanadyl porphyrins from heavy oil resins

A broad fraction of petroleum vanadyl porphyrins of high spectral purity was isolated from heavy oil resins with high vanadium content using a two-step chromatographic method. At the first step, the primary concentrate of vanadyl porphyrins was separated from the resins on the silica gel column. At the second step, it was further purified by the gradient elution through the column packed with sulfo-cationite. According to UV—VIS spectroscopy, this technique allows one to isolate up to 70% of vanadyl porphyrins with the spectral purity corresponding to the best results of other purification methods providing only narrow fractions of vanadyl porphyrins of comparable purity. Deoxophylloerythroetioporphyrin (DPEP) and etioporphyrin (Etio) series of vanadyl porphyrins with the carbon number range of C{sub 28}—C{sub 42} and DPEP/ Etio ratio equal to 1.18 were identified by MALDI-TOF mass-spectrometry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of steel type on the propensity for tribochemical wear in boundary lubrication with a wind turbine gear oil

Tribochemical wear may occur at the interface between a surface and a lubricant as a result of chemical and mechanical interactions in a tribological contact. Understanding the onset of tribochemical wear damage on component surfaces requires the use of high resolution techniques such as transmission electron microscopy (TEM). In this study, two steel types, case carburized AISI 3310 and through-hardened AISI 52100, were wear tested using a ball-on-disk rolling/sliding contact tribometer in fully formulated commercial wind turbine gearbox oil under boundary lubrication conditions with 10% slip. With the exception of steel type, all other test conditions were held constant. Conventional tribofilm analysis in the wear tracks was performed using X-ray photoelectron spectroscopy, and no significant composition differences were detected in the tribofilms for the different steel disk types. However, TEM analysis revealed significant tribochemical wear differences between the two steel types at multiple length scales, from the near-surface material microstructure (depth < 500 nm) to the tribofilm nanostructure. Nanometer-scale interfacial cracking and surface particle detachment was observed for the AISI 52100 case, whereas the tribofilm/substrate interface was abrupt and undamaged for the AISI 3310 case. Differences in tribofilm structure, including the location and orientation of MoS{sub 2} single sheet inclusions, were observed as a function of steel type as well. It is suggested that the tribochemical wear modes observed in these experiments may be origins of macroscopic surface-initiated damage such as micropitting in bearings and gears.

17 WIND ENERGY↗

Tribological Properties of Surface-Textured and Plasma-Nitrided Pure Titanium Under Oil Lubrication Condition

Plasma nitriding was conducted as post-treatment for surface texture on pure titanium to obtain a continuous nitriding layer. Supersonic fine particles bombarding (SFPB) was carried out to prepare surface texture. The surface morphologies and chemical composition were analyzed using scanning electron microscope and energy disperse spectroscopy. The microstructures of modified layers were characterized by transmission electron microscope. The tribological properties of surface-textured and duplex-treated pure titanium under oil lubrication condition were systematically investigated in the ball-on-plate reciprocating mode. The effects of applied load and sliding velocity on the tribological behavior were analyzed. The results show that after duplex treatments, the grains size in modified layer becomes slightly larger, and hardness is obviously improved. Wear resistance of duplex-treated pure titanium is significantly improved referenced to untreated and surface-textured pure titanium, which is 3.22 times as much as untreated pure titanium and 2.15 times of that for surface-textured pure titanium, respectively.

36 MATERIALS SCIENCE↗

Impact of Lubricant Oil Additives on the Performance of Pd-Based Three-Way Catalysts

As alternative lubricant anti-wear additives are sought to reduce friction and improve overall fuel economy, it is important that these additives are also compatible with current emissions control catalysts. In the present work, a second-generation oil-miscible phosphorous-containing ionic liquid (IL), is evaluated for its impact on Pd-based three-way catalyst (TWC) reactivity and benchmarked against the industry standard zinc dialkyl-dithio-phosphate (ZDDP). The TWCs are exposed to the lubricant additives in an engine bench under four different scenarios: base case with no additive (NA), ZDDP-only, IL-only, and IL + ZDDP. The engine-aged TWC samples, along with the as-received TWC, are characterized through various analytical techniques including catalyst reactivity evaluation in a bench-flow reactor. The temperature of 50% conversion (T 50 ) for the ZDDP-aged TWC increases by 11, 21, and 36 °C for CO, C 3 H 6 , and C 3 H 8 , respectively, as compared with the no-additive case. Similarly, the T50 for IL-only and IL + ZDDP-aged TWCs also increase as compared with the no-additive case. Even though the water-gas-shift (WGS) reactivity is similar for all engine-aged samples, the IL-aged TWC had higher oxygen storage capacity than the ZDDP-aged TWC. EPMA analysis reveals penetration of phosphorus deep into the washcoat for all engine-aged TWCs. Results from XRD indicate the presence of CePO 4 and AlPO 4 on the washcoat of IL, ZDDP, and IL + ZDDP-aged TWC samples but not on the fresh and NA TWC samples. Additionally, ICP-OES results show a large amount of phosphorus in the washcoat of IL, ZDDP and IL + ZDDP-aged TWC samples and a lesser amount in NA TWC samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Oil and gas produced water as a growth medium for microalgae cultivation: A review and feasibility analysis

Scale-up of microalgal biotechnology to provide large quantities of biofuel, lipids, and coproducts is not fully developed because of the large needs for nutrients, water, land, solar insolation, and CO 2 /carbon supplies. Wastewaters, including oil and gas produced water (PW), may supply a portion of these needs in regions with insufficient fresh water resources. PW is a challenging water resource for this use because of variable salinity, geochemical complexity, and the presence of biologically toxic components. In this paper we review PW volumes, quality, and use in media for microalgae production in the southwestern US, Australia, and Oman. We also include data from the southwestern US, referencing previously unpublished results from the National Alliance for Biofuels and Bioproducts (NAABB) consortium research project. We include a Supplementary Information section that explores cultivation of multiple microalgae species in PW and examines the carbon utilization process, all work performed in support of the NAABB field program. Strains of algae tested in the reviewed papers include Nannochloropsis , Dunalliella , Scenedesmus , and several mixed or unknown cultures. We conclude that the use of PW in algae cultivation is feasible, if the additional complexity of the water resource is accounted for in developing media formulations and in understanding metals uptake by the algae. We recommend additional work to standardize growth testing in PW, better and more thorough chemical analysis, and geochemical modeling of the PW used in media. As a result, expanded strain testing in PW media will identify improved strains tolerant of PW in algae cultivation.

59 BASIC BIOLOGICAL SCIENCES↗

Catalytic Conversion of Model Compounds of Plastic Pyrolysis Oil over ZSM-5

Mechanistic investigation of the catalytic conversion of model compounds for plastic pyrolysis oil (1-octene, octadiene, octane, and toluene) over ZSM-5 in a fixed-bed reactor was studied. 1-Octene breaks down into smaller olefins, which undergo further cracking, oligomerization, cyclization, and hydrogen transfer to eventually produce benzene, toluene, xylene (BTX), coke, and hydrogen. The effect of contact time on 1-octene conversion was further investigated and compared with thermodynamics analyses to elucidate the reaction network. Under the reaction conditions (500 oC, 1 atm), octadiene undergoes thermal coking, significantly contributing to reactor fouling. The products from octane cracking are similar to the products from 1-octene conversion whereas toluene undergoes disproportionation, dealkylation and coking. The analysis of spent catalyst showed long-chain hydrocarbons created by oligomerization reactions filled the pores and covered the surface of the catalyst. As a result, when mesoporous ZSM-5 is used instead of conventional, product selectivity is maintained for 70 hours in time-on-stream experiments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization and microbial mitigation of fugitive methane emissions from oil and gas wells: Example from Indiana, USA

Hydrocarbon gas emissions from active, inactive, and improperly sealed or abandoned oil/gas wells significantly contribute to anthropogenically emitted greenhouse gases, predominantly in the form of methane (CH 4 ). We explored the extent of hydrocarbon gas emissions from 20 active, inactive, plugged and abandoned oil/gas wells in Indiana (USA), where it is estimated that there are more than 80,000 well sites throughout the state. After this initial survey, using a static flux tent, we quantified fugitive CH4 emissions from an active gas well to approximately 2 L h -1 . To evaluate the potential for microbial mitigation of hydrocarbon emissions to the atmosphere, we conducted laboratory microcosm experiments to quantify the CH 4 oxidizing potential of soils collected from sites with varying distances to the leaking gas well. Soils in close proximity to the well (0.5 m) efficiently consumed nearly all (97 %) of the added CH 4 , while only 14 % of added CH 4 was consumed by soils that were more distant from the well (20 m). These results suggest that fugitive CH 4 emissions enrich methanotrophic bacteria in soils immediately adjacent to the well. Consistent with this view, we found that prolonged exposure of soils to elevated concentrations of CH 4 enhanced the methanotrophic activity. Together, these findings prompted us to design a “methanotrophic soil mound” to assess the feasibility of mitigating point sources of CH 4 by harnessing the natural methanotrophic capacity of soil microbial communities. We found that a methanotrophic soil mound from a landfill could sustainably mitigate the CH 4 emission from the artificial source, providing a promising low-cost solution to ameliorate fugitive CH 4 emissions from abandoned oil and gas wells to the atmosphere. Finally, the effectiveness of microbe-based remediation is limited in cold climates and arid environments.

54 ENVIRONMENTAL SCIENCES↗

High surface area mesoporous tungsten oxide for fast, green oxidation of organosulfur compounds in crude oil

Mesoporous, multi-valent tungsten oxide with high surface area (209 m 2 /g) is synthesized via a novel metal dissolution coupled with reverse micelle formation approach. Mesoporous tungsten oxide with highest surface area reported is obtained by this method. The material is used as an excellent heterogeneous catalyst for the oxidation of organosulfur compounds present in crude oil. The complete oxidation of dibenzothiophene was observed with excellent yield (>99%) within 15 min at room temperature (20 °C). The catalyst is reusable up to 5 reaction cycles without losing significant activity. A green oxidant, H 2 O 2 is used and the reaction mechanism involves the activation of peroxo species by W 6+ . The oxidation activity decreases in the order of DBT > 4,6-DMDBT > 1-BT due to the changes in the electronic environment of sulfur and steric effects.

36 MATERIALS SCIENCE↗

Russian Policy on Methane Emissions in the Oil and Gas Sector: A Case Study in Opportunities and Challenges in Reducing Short-Lived Forcers

This paper uses Russian policy in the oil and gas sector as a case study in assessing options and challenges for scaling-up emission reductions. We examine the challenges to achieving large-scale emission reductions, successes that companies have achieved to date, how Russia has sought to influence methane emissions through its environmental fine system, and options for helping companies achieve large-scale emission reductions in the future through simpler and clearer incentives.

Evans, Meredydd↗

Mathematical Programming Models for Shale Oil & Gas Development: A Review and Perspective

Here, in this paper, we provide a comprehensive review of mathematical programming models for shale oil & gas development, and we offer a perspective on outstanding research opportunities. We distinguish contributions in five major topic areas, namely: (1) development planning, (2) water management, (3) production optimization, (4) supplies, gathering & processing, and (5) life cycle analysis & sustainability. We highlight how various types of mathematical programming models (i.e., linear programs, nonlinear programs, mixed-integer linear programs, mixed-integer nonlinear programs) have been proposed primarily by the Process Systems Engineering community to address the respective decision-making problems, and we highlight instances of successful deployment in industry. Finally, based on a critical assessment of the existing body of work, we identify opportunities for future research across the major topic areas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗