Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Load Profile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Long cycle life microporous spherical carbon anodes for sodium-ion batteries derived from furfuryl alcohol

Spherical micron-sized carbon powders were synthesized from feedstock furfuryl alcohol and tested as anodes in sodium ion batteries (SIBs). A long cycle life of 1000 cycles is achievable with this carbon at C rate (3–4 mg cm –2 loading and i = 200 mA g –1 ) yielding a steady capacity of ca. 115 mA h g –1 . Furthermore, the results from solid-state 23Na MAS NMR analyses of cycled electrodes indicate no correlation in voltage profiles with sodium site nature (graphene or nanopores), which is a new observation in SIB carbon anodes.

25 ENERGY STORAGE↗

Optimal Capacitor Bank Capacity and Placement in Distribution Systems with High Distributed Solar Power Penetration

Capacitor banks have been generally installed and utilized to support distribution voltage during period of higher load or on longer, higher impedance, feeders. Installations of distributed energy resources in distribution systems are rapidly increasing, and many of these generation resources have variable and uncertain power output. These generators can significantly change the voltage profile across a feeder, and therefore when a new capacitor bank is needed analysis of optimal capacity and location of the capacitor bank is required. In this paper, we model a particular distribution system including essential equipment. An optimization method is adopted to determine the best capacity and location sets of the newly installed capacitor banks, in the presence of distributed solar power generation. Finally we analyze the optimal capacitor banks configuration through the optimization and simulation results.

14 SOLAR ENERGY↗

SU-E-T-283: Dose Perturbations Near Heterogeneity Junctions for Modulated-Scanning Protons

Purpose: To compare calculated and measured doses near heterogeneity junctions of tissue-substitute materials for modulated-scanning protons. Methods: Three heterogeneous phantoms were configured using slabs of various plastics to simulate lung, fat, soft-tissue (polystyrene), and bone with known relative linear stopping powers (RLSPs). Each phantom consisted of soft-tissue and a single heterogeneity of a 5 or 10 cm thickness of a non-soft-tissue material. CT images were loaded into a Syngo treatment planning system and each material contoured and assigned its RLSP. Planning target volumes (PTVs) were drawn such that a beam would partially traverse the heterogeneity and partially only soft-tissue. Lateral profiles were measured using EDR2 films at a minimum of six depths between the phantom surface and the depth corresponding to the beam range. Absolute doses were measured inside and distal to the PTV in all phantoms using either a parallel plate or thimble chamber. Additional dose measurements were made between two lung slabs. Results: Profiles measured by film generally agreed with calculations except for depths distal to lung and fat junctions. Measured lateral penumbras for depths at the distal junction of lung were found to be wider than calculated ones. Compared with calculated doses, measured doses in the PTVs were 5.19% and 2.51% lower for lung and fat respectively but for bone were 0.2% higher. Measured doses for depths distal to the PTV were up to 29.65% and 10.58% higher for lung and fat, respectively but 6.30% lower for bone. Conclusion: The low measured doses in the PTVs for lung and fat might be due to underestimation of lateral scattering of protons. The higher measured doses distal to the PTV for the lung and fat are a Result of a shortened calculated beam range whereas the higher dose distal to the bone junction is within uncertainties.

60 APPLIED LIFE SCIENCES↗

Extreme Miller cycle with high intake boost for improved efficiency and emissions in heavy-duty diesel engines

This study experimentally investigates the impact of extreme Miller cycle strategies paired with high intake manifold pressures on the combustion process, emissions, and thermal efficiency of heavy-duty diesel engines. Well-controlled experiments isolating the effect of Miller cycle strategies on the combustion process were conducted at constant engine speed and load (1160 rpm, 1.76 MPa net IMEP) on a single cylinder research engine equipped with a fully-flexible hydraulic valve train system. Late intake valve closing (LIVC) timing strategies were compared to a conventional intake valve profile under either constant cylinder composition, constant engine-out NO x emission, or constant overall turbocharger efficiency (η TC ) to investigate the operating constraints that favor Miller cycle operation over the baseline strategy. Furthermore, utilizing high boost with conventional intake valve closing timing resulted in improved fuel consumption at the expense of sharp increases in peak cylinder pressures, engine-out NO x emissions, and reduced exhaust temperatures. Miller cycle without EGR at constant λ demonstrated LIVC strategies effectively reduce engine-out NO x emissions by up to 35%. However, Miller cycle associated with very aggressive LIVC timings led to fuel consumption penalties due to increased pumping work and exhaust enthalpy. LIVC strategies allowed for increased charge dilution at the baseline NO x constraint of 3.2 g/kWh, resulting in significant fuel consumption benefits over the baseline case without compromising exhaust temperatures or peak cylinder pressures. As Miller cycle implementation was shown to affect the boundary conditions dictating η TC , the LIVC and conventional IVC cases were studied at an equivalent η TC point representative of high boost operation. With high boost, LIVC yielded reduced NO x emissions, reduced peak cylinder pressures, and elevated exhaust temperatures compared to the conventional IVC case without compromising fuel consumption.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Atmospheric Boundary Layer-Wind Farm Interactions Field Campaign Report

The American WAKE ExperimeNt (AWAKEN) was a field campaign in northern Oklahoma intended to analyze the potential influence of wind farms and their collective wakes on the atmospheric boundary layer (ABL), wind power production, and turbine structural loads. This report summarizes the deployment of instruments by the University of Oklahoma (OU), National Atmospheric and Atmospheric Administration National Severe Storms Laboratory (NOAA NSSL), and Lawrence Livermore National Laboratory (LLNL) during AWAKEN. Two Collaborative Lower Atmosphere Profiling Systems (CLAMPS) and LLNL ZephIR profiling lidars were co-deployed from October 3, 2022, to December 20, 2022 (winter campaign). At the end of the winter campaign, both ZephIR lidars were moved to different AWAKEN sites to be a part of a targeted wake study at the King Plains wind farm. The two CLAMPS were redeployed for a second observation period from July 1st, 2023, to September 28, 2023 (summer campaign; the ZephIR lidars were not co-located with CLAMPS).

54 ENVIRONMENTAL SCIENCES↗

Transient characteristics of a grooved water heat pipe with variable heat load

The transient characteristics of a grooved water heat pipe were studied by using variable heat load. First, the effects of the property variations of the working fluid with temperature were investigated by operating the water heat pipe at several different temperatures. The experimental results show that, even for the same heat input profile and heat pipe configuration, the heat pipe transports more heat at higher temperature within the tested temperature range. Adequate liquid return to the evaporator due to decreasing viscosity of the working fluid permits continuous vaporization of water without dry-out. Second, rewetting of the evaporator was studied after the evaporator had experienced dry-out. To rewet the evaporator, the elevation of the condenser end was the most effective way. Without elevating the condenser end, rewetting is not straight-forward even with power turned off unless the heat pipe is kept at isothermal condition for sufficiently long time.

Jang, Jong Hoon↗

A study of high-temperature heat pipes with multiple heat sources and sinks. I - Experimental methodology and frozen startup profiles. II - Analysis of continuum transient and steady-state experimental data with numerical predictions

Experimental profiles for heat pipe startup from the frozen state were obtained, using a high-temperature sodium/stainless steel pipe with multiple heat sources and sinks to investigate the startup behavior of the heat pipe for various heat loads and input locations, with both low and high heat rejection rates at the condensor. The experimental results of the performance characteristics for the continuum transient and steady-state operation of the heat pipe were analyzed, and the performance limits for operation with varying heat fluxes and location are determined.

Faghri, A.↗

The Profile Envision and Splice Tool (PRESTO): Developing an Atmospheric Wind Analysis Tool for Space Launch Vehicles Using Python

Tropospheric winds are an important driver of the design and operation of space launch vehicles. Multiple types of weather balloons and Doppler Radar Wind Profiler (DRWP) systems exist at NASA's Kennedy Space Center (KSC), co-located on the United States Air Force's (USAF) Eastern Range (ER) at the Cape Canaveral Air Force Station (CCAFS), that are capable of measuring atmospheric winds. Meteorological data gathered by these instruments are being used in the design of NASA's Space Launch System (SLS) and other space launch vehicles, and will be used during the day-of-launch (DOL) of SLS to aid in loads and trajectory analyses. For the purpose of SLS day-of-launch needs, the balloons have the altitude coverage needed, but take over an hour to reach the maximum altitude and can drift far from the vehicle's path. The DRWPs have the spatial and temporal resolutions needed, but do not provide complete altitude coverage. Therefore, the Natural Environments Branch (EV44) at Marshall Space Flight Center (MSFC) developed the Profile Envision and Splice Tool (PRESTO) to combine balloon profiles and profiles from multiple DRWPs, filter the spliced profile to a common wavelength, and allow the operator to generate output files as well as to visualize the inputs and the spliced profile for SLS DOL operations. PRESTO was developed in Python taking advantage of NumPy and SciPy for the splicing procedure, matplotlib for the visualization, and Tkinter for the execution of the graphical user interface (GUI). This paper describes in detail the Python coding implementation for the splicing, filtering, and visualization methodology used in PRESTO.

Orcutt, John M.↗

Using Whole-House Field Tests to Empirically Derive Moisture Buffering Model Inputs

Building energy simulations can be used to predict a building's interior conditions, along with the energy use associated with keeping these conditions comfortable. These models simulate the loads on the building (e.g., internal gains, envelope heat transfer), determine the operation of the space conditioning equipment, and then calculate the building's temperature and humidity throughout the year. The indoor temperature and humidity are affected not only by the loads and the space conditioning equipment, but also by the capacitance of the building materials, which buffer changes in temperature and humidity. This research developed an empirical method to extract whole-house model inputs for use with a more accurate moisture capacitance model (the effective moisture penetration depth model). The experimental approach was to subject the materials in the house to a square-wave relative humidity profile, measure all of the moisture transfer terms (e.g., infiltration, air conditioner condensate) and calculate the only unmeasured term: the moisture absorption into the materials. After validating the method with laboratory measurements, we performed the tests in a field house. A least-squares fit of an analytical solution to the measured moisture absorption curves was used to determine the three independent model parameters representing the moisture buffering potential of this house and its furnishings. Follow on tests with realistic latent and sensible loads showed good agreement with the derived parameters, especially compared to the commonly-used effective capacitance approach. These results show that the EMPD model, once the inputs are known, is an accurate moisture buffering model.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Using Whole-House Field Tests to Empirically Derive Moisture Buffering Model Inputs

Building energy simulations can be used to predict a building's interior conditions, along with the energy use associated with keeping these conditions comfortable. These models simulate the loads on the building (e.g., internal gains, envelope heat transfer), determine the operation of the space conditioning equipment, and then calculate the building's temperature and humidity throughout the year. The indoor temperature and humidity are affected not only by the loads and the space conditioning equipment, but also by the capacitance of the building materials, which buffer changes in temperature and humidity. This research developed an empirical method to extract whole-house model inputs for use with a more accurate moisture capacitance model (the effective moisture penetration depth model). The experimental approach was to subject the materials in the house to a square-wave relative humidity profile, measure all of the moisture transfer terms (e.g., infiltration, air conditioner condensate) and calculate the only unmeasured term: the moisture absorption into the materials. After validating the method with laboratory measurements, we performed the tests in a field house. A least-squares fit of an analytical solution to the measured moisture absorption curves was used to determine the three independent model parameters representing the moisture buffering potential of this house and its furnishings. Follow on tests with realistic latent and sensible loads showed good agreement with the derived parameters, especially compared to the commonly-used effective capacitance approach. These results show that the EMPD model, once the inputs are known, is an accurate moisture buffering model.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Criticality safety analysis of spent fuel storage or handling disposals using burnup credit - loading curve calculation - 14445

MILLENNIUM and REEL SAS Companies have shared their own experience to develop a neutron and criticality calculations chain in order to perform isotopic composition predictions of spent fuel after irradiation in a reactor and criticality analysis of fuel storages taking into account burnup credit. The whole calculation sequence is divided into three steps, all calling SCALE 6.1.2 modules. The first two steps are dedicated to the evaluation of isotopic compositions of burnt fuel. As transport and depletion calculations in three dimensions appears to be way too long for the whole core (about several months), dealing with each fuel assembly one by one is the alternative solution MILLENNIUM and REEL SAS commonly chose to study. Therefore, the first step aims at determining the axial burnup profile of a given fuel assembly using a 3-D model with infinite reflections on lateral axes. The T6-depl sequence of TRITON module coupling KENO-VI and ORIGEN-S was used in this step. Sensitivity studies confirmed that addition of the 8 closest neighbors of the studied fuel assembly in the model has an insignificant impact on the axial burnup profile. However, fuel assemblies in the peripheral zone of the core must be treated separately with a model including the nearest fuel assemblies and the effect of peripheral water. Then, the second phase evaluates the isotopic compositions of each fuel assemblies at the center of the active height with a 2-D model under conservative core conditions. The T-depl sequence of the TRITON module coupling NEWT to ORIGEN-S is called in this step. Each fuel assembly must be studied separately to consider loading pattern changes occurring at each cycle. An infinite model with reflections on lateral axes is used and the closest neighbors of the fuel assembly are limited to 2 pins - which is around the size of the neutrons mean free path in the core. This is an innovative physical trick aiming at compensating for a limited computing power. Finally, isotopic compositions calculated are combined with the axial burnup profile of the first step to extrapolate the concentrations along the whole active length. Data can then be added in any criticality model, such as a spent fuel pit or any disposal handling fuel assemblies. Criticality analyses of burnt fissile material using burnup credit can be managed within a reasonable amount of time, on condition that sufficient proofs of code qualification for the studied range of parameters are provided, especially on fission products isotopic compositions calculation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Assessment of the methane oxidation capacity of compacted soils intended for use as landfill cover materials

The microbial oxidation of methane in engineered cover soils is considered a potent option for the mitigation of emissions from old landfills or sites containing wastes of low methane generation rates. A laboratory column study was conducted in order to derive design criteria that enable construction of an effective methane oxidising cover from the range of soils that are available to the landfill operator. Therefore, the methane oxidation capacity of different soils was assessed under simulated landfill conditions. Five sandy potential landfill top cover materials with varying contents of silt and clay were investigated with respect to methane oxidation and corresponding soil gas composition over a period of four months. The soils were compacted to 95% of their specific proctor density, resulting in bulk densities of 1.4-1.7 g cm{sup -3}, reflecting considerably unfavourable conditions for methane oxidation due to reduced air-filled porosity. The soil water content was adjusted to field capacity, resulting in water contents ranging from 16.2 to 48.5 vol.%. The investigated inlet fluxes ranged from 25 to about 100 g CH{sub 4} m{sup -2} d{sup -1}, covering the methane load proposed to allow for complete oxidation in landfill covers under Western European climate conditions and hence being suggested as a criterion for release from aftercare. The vertical distribution of gas concentrations, methane flux balances as well as stable carbon isotope studies allowed for clear process identifications. Higher inlet fluxes led to a reduction of the aerated zone, an increase in the absolute methane oxidation rate and a decline of the relative proportion of oxidized methane. For each material, a specific maximum oxidation rate was determined, which varied between 20 and 95 g CH{sub 4} m{sup -2} d{sup -1} and which was positively correlated to the air-filled porosity of the soil. Methane oxidation efficiencies and gas profile data imply a strong link between oxidation capacity and diffusive ingress of atmospheric air. For one material with elevated levels of fine particles and high organic matter content, methane production impeded the quantification of methane oxidation potentials. Regarding the design of landfill cover layers it was concluded that the magnitude of the expected methane load, the texture and expected compaction of the cover material are key variables that need to be known. Based on these, a column study can serve as an appropriate testing system to determine the methane oxidation capacity of a soil intended as landfill cover material.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

High energy X-ray diffraction study of the relationship between the macroscopic mechanical properties and microstructure of irradiated HT-9 steel

Samples harvested from an HT-9 fuel test assembly (ACO-3) irradiated for six years in the Fast Flux Test Facility (FFTF) reaching 2–147 dpa at 382–504°C were deformed in-situ while collecting high-energy X-ray diffraction data to monitor microstructure evolution. With the initiation of plastic deformation, all samples exhibited a clear load transfer from the ferrite matrix to carbide particulate. This behavior was confirmed by modeling of the control material. The evolution of dislocation density in the material as a result of deformation was characterized through full pattern line profile analysis. The dislocation densities increased substantially after deformation, the level of dislocation evolution observed was highly dependent upon the irradiation temperature of the sample. The differences in both the yield and hardening behavior between samples irradiated at higher and lower temperatures suggest the existence of a transition in tensile behavior at an irradiation temperature near 420°C dividing regions of distinct damage effects.

36 MATERIALS SCIENCE↗

Magnetic transport apparatus for the production of ultracold atomic gases in the vicinity of a dielectric surface

We present an apparatus designed for studies of atom-surface interactions using quantum degenerate gases of {sup 85}Rb and {sup 87}Rb in the vicinity of a room temperature dielectric surface. The surface to be investigated is a super-polished face of a glass Dove prism mounted in a glass cell under ultra-high vacuum. To maintain excellent optical access to the region surrounding the surface, magnetic transport is used to deliver ultracold atoms from a separate vacuum chamber housing the magneto-optical trap (MOT). We present a detailed description of the vacuum apparatus highlighting the novel design features; a low profile MOT chamber and the inclusion of an obstacle in the transport path. We report the characterization and optimization of the magnetic transport around the obstacle, achieving transport efficiencies of 70% with negligible heating. Finally, we demonstrate the loading of a hybrid optical-magnetic trap with {sup 87}Rb and the creation of Bose-Einstein condensates via forced evaporative cooling close to the dielectric surface.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Flow strength of tantalum under ramp compression to 250 GPa

A magnetic loading technique was used to study the strength of polycrystalline tantalum ramp compressed to peak stresses between 60 and 250 GPa. Velocimetry was used to monitor the planar ramp compression and release of various tantalum samples. A wave profile analysis was then employed to determine the pressure-dependence of the average shear stress upon unloading at strain rates on the order of 10{sup 5} s{sup −1}. Experimental uncertainties were quantified using a Monte Carlo approach, where values of 5% in the estimated pressure and 9–17% in the shear stress were calculated. The measured deviatoric response was found to be in good agreement with existing lower pressure strength data as well as several strength models. Significant deviations between the experiments and models, however, were observed at higher pressures where shear stresses of up to 5 GPa were measured. Additionally, these data suggest a significant effect of the initial material processing on the high pressure strength. Heavily worked or sputtered samples were found to support up to a 30% higher shear stress upon release than an annealed material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optimal Control of Distributed Energy Resources using Model Predictive Control

In an isolated power system (rural microgrid), Distributed Energy Resources (DERs) such as renewable energy resources (wind, solar), energy storage and demand response can be used to complement fossil fueled generators. The uncertainty and variability due to high penetration of wind makes reliable system operations and controls challenging. In this paper, an optimal control strategy is proposed to coordinate energy storage and diesel generators to maximize wind penetration while maintaining system economics and normal operation. The problem is formulated as a multi-objective optimization problem with the goals of minimizing fuel costs and changes in power output of diesel generators, minimizing costs associated with low battery life of energy storage and maintaining system frequency at the nominal operating value. Two control modes are considered for controlling the energy storage to compensate either net load variability or wind variability. Model predictive control (MPC) is used to solve the aforementioned problem and the performance is compared to an open-loop look-ahead dispatch problem. Simulation studies using high and low wind profiles, as well as, different MPC prediction horizons demonstrate the efficacy of the closed-loop MPC in compensating for uncertainties in wind and demand.

Mayhorn, Ebony T.↗

Intrabasin Comparison of Produced Fluid From Hydraulically Fractured Wells in the Permian Region

The Permian Basin is the highest producing oil and gas reservoir in the United States. Hydrocarbon extraction methods in this region are often associated with frac hits, or interwell communication events where an established well is affected by the pumping of fracture fluid into a new well. Our previous work revealed a unique geochemical signal indicating the presence of frac hits in the Permian Basin. We returned to this area with the overall goal of expanding our understanding of the microbial and geochemical dynamics common in this region. To do so, we collected produced water from 25 unique sites across the Permian Basin, 10 of which had previously been characterized during an active frac hit with the rest being novel. For each sample, we measured the pH, alkalinity, geochemical composition, microbial load (qPCR), and microbial community composition (16S rRNA sequencing). Permian Basin produced water is characterized by higher sulfate and lower total dissolved solids (TDS) concentrations compared to other regions. Interestingly, wells impacted by frac hits have a geochemical profile that resembles that of fracture fluid, with both lowered sulfate and lowered TDS concentrations compared to unaffected wells in this region. Due to the year-long recovery window between sample collection periods, we anticipate that all of our data will be characterized by the typical high sulfate, low TDS concentrations.

environmental microbiology↗

Enhanced automated spiral bevel gear inspection

Presented here are the results of a manufacturing and technology program to define, develop, and evaluate an enhanced inspection system for spiral bevel gears. The method uses a multi-axis coordinate measuring machine which maps the working surface of the tooth and compares it with nominal reference values stored in the machine's computer. The enhanced technique features a means for automatically calculating corrective grinding machine settings, involving both first and second order changes, to control the tooth profile to within specified tolerance limits. This enhanced method eliminates the subjective decision making involved in the tooth patterning method, still in use today, which compares contract patterns obtained when the gear is set to run under light load in a rolling test machine. It produces a higher quality gear with significant inspection time and cost savings.

Frint, Harold K.↗