Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FACILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Advanced Hypervelocity Aerophysics Facility Workshop

The primary objective of the workshop was to obtain a critical assessment of a concept for a large, advanced hypervelocity ballistic range test facility powered by an electromagnetic launcher, which was proposed by the Langley Research Center. It was concluded that the subject large-scale facility was feasible and would provide the required ground-based capability for performing tests at entry flight conditions (velocity and density) on large, complex, instrumented models. It was also concluded that advances in remote measurement techniques and particularly onboard model instrumentation, light-weight model construction techniques, and model electromagnetic launcher (EML) systems must be made before any commitment for the construction of such a facility can be made.

Witcofski, Robert D.↗
NASA NTRS1991

Designs for surge immunity in critical electronic facilities

In recent years, Federal Aviation Administration (FAA) embarked on a program replacing older tube type electronic equipment with newer solid state equipment. This replacement program dramatically increased the susceptibility of the FAA's facilities to lightning related damages. The proposal is presented of techniques which may be employed to lessen the susceptibility of new FAA electronic facility designs to failures resulting from lightning related surges and transients as well as direct strikes. The general concept espoused is one of a consistent system approach employing both perimeter and internal protection. It compares the technique presently employed to reduce electronic noise with other techniques which reduce noise while lowering susceptibility to lightning related damage. It is anticipated that these techniques will be employed in the design of an Air Traffic Control Tower in a high isokeraunic area. This facility would be subjected to rigorous monitoring over a multi-year period to provide quantitative data hopefully supporting the advantage of this design.

Roberts, Edward F., Jr.↗
NASA NTRS1991

The Sandia transportable triggered lightning instrumentation facility

Development of the Sandia Transportable Triggered Lightning Instrumentation Facility (SATTLIF) was motivated by a requirement for the in situ testing of a munitions storage bunker. Transfer functions relating the incident flash currents to voltages, currents, and electromagnetic field values throughout the structure will be obtained for use in refining and validating a lightning response computer model of this type of structure. A preliminary shakedown trial of the facility under actual operational conditions was performed during summer of 1990 at the Kennedy Space Center's (KSC) rocket-triggered lightning test site. A description is given of the SATTLIF, which is readily transportable on a single flatbed truck of by aircraft, and its instrumentation for measuring incident lightning channel currents and the responses of the systems under test. Measurements of return-stroke current peaks obtained with the SATTLIF are presented. Agreement with data acquired on the same flashes with existing KSC instrumentation is, on average, to within approximately 7 percent. Continuing currents were measured with a resolution of approximately 2.5 A. This field trial demonstrated the practicality of using a transportable triggered lightning facility for specialized test applications.

Schnetzer, George H.↗
NASA NTRS1991

A simulated lightning effects test facility for testing live and inert missiles and components

Details of a simulated lightning effects test facility for testing live and inert missiles, motors, and explosive components are described. The test facility is designed to simulate the high current, continuing current, and high rate-of-rise current components of an idealized direct strike lightning waveform. The Lightning Test Facility was in operation since May, 1988, and consists of: 3 separate capacitor banks used to produce the lightning test components; a permanently fixed large steel safety cage for retaining the item under test (should it be ignited during testing); an earth covered bunker housing the control/equipment room; a charge/discharge building containing the charging/discharging switching; a remotely located blockhouse from which the test personnel control hazardous testing; and interconnecting cables.

Craven, Jeffery D.↗
NASA NTRS1990

The Marshall Space Flight Center Drop Tube Facility

The structural and instrumentation hardware and the improved experimental capabilities of a 105-m Drop Tube Facility are described. The structure is designed to provide a high-vacuum facility in a vertical orientation. The low-gravity environment obtained during free-fall and the containerless materials processing capabilities are discussed. Two furnaces, an electron-beam and an electromagnetic levitator, are used to melt metallic samples in a process environment ranging from 10 to the -6th torr to 1 atm. Specifics of the vacuum control and gas delivery systems are provided. The experimental instrumentation and data acquisition systems used to perform predrop and in-flight measurements of the melting and solidification process are discussed. Typical experimental results are presented as an indicator of the performance of the Drop Tube Facility.

Rathz, Thomas J.↗
NASA NTRS1990

Requirements and concept for an on-orbit construction facility for phase 1 Space Station Freedom

A construction facility attached to NASA's Space Station Freedom (SSF) will be required for the accommodation of assembly activities for large payloads, as well as demonstration of the on-orbit construction of future spacecraft. This facility's capabilities must be sufficiently flexible to address the wide variety of future spacecraft needs without compromising the SSF's phase 1 configuration. The proposed construction facility concept will incorporate a storage module, a construction turntable, equipment-attachment platforms, a surrogate payload bay structure, and a portable workstation. Attention is given to this configuration's resulting mass properties and control characteristics.

Buchan, Robert W.↗
NASA NTRS1990

Development of experimental facilities for processing metallic crystals in orbit

This paper discusses the evolution, current status, and planning for facilities to exploit the microgravity environment of earth orbit in applied metallic materials science. Space-Shuttle based facilities and some precursor flight programs are reviewed. Current facility development programs and planned Space Station furnace capabilities are described. The reduced gravity levels available in earth orbit allow the processing of metallic materials without the disturbing influence of gravitationally induced thermal convection, stratification due to density differences in sample components, or the effects of hydrostatic pressure.

Duncan, Bill J.↗
NASA NTRS1991

Enhanced capability of the Combustion-Heated Scramjet Test Facility

The Combustion-Heated Scramjet Test Facility (CHSTF) is described together with its modifications. The expanded simulation capabilities of the facility are documented. Nozzle exit surveys and tunnel calibration information are presented. It is noted that these modifications included a new heat-sink nickel liner heater, a new Mach 4.7 nozzle, and a new 70-ft vacuum sphere exhaust system. It is found that the facility in the air ejector mode of operation performed similarly to that prior to the addition of the vacuum sphere ducting.

Rock, Kenneth E.↗
NASA NTRS1991

NASA/MSFC Large Space Structures Ground Test Facility

This paper describes the NASA/MSFC Large Space Structures Ground Test Facility (LSS GTF) which has been developed for the purpose of implementing, testing, and evaluating LSS control and system identification techniques on representative large space structures. The facility presently consists of two laboratories: the Single Structure Control (SSC) Laboratory, which has been operational since 1984, and the Controls and Structures Experiment in Space (CASES) GTF which is presently under development. Test results from several experiments in the SSC laboratory are presented. The results of component testing and boom modal tests are presented for the CASES facility.

Jones, Victoria L.↗
NASA NTRS1991

Description of Liquid Nitrogen Experimental Test Facility

The Liquid Nitrogen Test Facility is a unique test facility for ground-based liquid nitrogen experimentation. The test rig consists of an insulated tank of approximately 12.5 cubic ft in volume, which is supplied with liquid nitrogen from a 300 gal dewar via a vacuum jacketed piping system. The test tank is fitted with pressure and temperature measuring instrumentation, and with two view ports which allow visual observation of test conditions. To demonstrate the capabilities of the facility, the initial test program is briefly described. The objective of the test program is to measure the condensation rate by injecting liquid nitrogen as a subcooled spray into the ullage of a tank 50 percent full of liquid nitrogen at saturated conditions. The condensation rate of the nitrogen vapor on the subcooled spray can be analytically modeled, and results validated and corrected by experimentally measuring the vapor condensation on liquid sprays.

Jurns, John M.↗
NASA NTRS1991

Status Update on the Seal/bearing Rotordynamics Test Facility at Case Western Reserve University

The CWRU Seal/Bearing test facility is shown along with the revised force measuring system. This facility has recently been retrofitted with a high pressure, high flow oil system. The high pressure high flow water system remains in place to test seals. Also, a new high flow air system is now installed. Thus, testing to determine static and dynamic properties can now be performed using oil, water, or air on this single facility. The oil system is currently being used to determine rotordynamic properties of a NASA four pocket hydrostatic journal bearing. The revised dual system force measuring configuration is performing with excellent accuracy. That is, the dynamic force measurements are made simultaneously with two independent systems, one with piezoelectric load cells and the other with strain gage load cells. The difference is less than 2 pct. between these two sets of load cell measurements on recent tests with a static eccentricity set close to zero and an orbit radius of 0.0004 inch. The extracted stiffness, damping and inertia coefficients is given for the test conditions shown, as extracted from the two independent dynamic force measurements.

Adams, Michael L.↗
NASA NTRS1991

Chemical hazards database and detection system for Microgravity and Materials Processing Facility (MMPF)

The ability to identify contaminants associated with experiments and facilities is directly related to the safety of the Space Station. A means of identifying these contaminants has been developed through this contracting effort. The delivered system provides a listing of the materials and/or chemicals associated with each facility, information as to the contaminant's physical state, a list of the quantity and/or volume of each suspected contaminant, a database of the toxicological hazards associated with each contaminant, a recommended means of rapid identification of the contaminants under operational conditions, a method of identifying possible failure modes and effects analysis associated with each facility, and a fault tree-type analysis that will provide a means of identifying potential hazardous conditions related to future planned missions.

Steele, Jimmy↗
NASA NTRS1992

The Critical Point Facility (CPF)

The Critical Point Facility (CPF) is an ESA multiuser facility designed for microgravity research onboard Spacelab. It has been conceived and built to offer investigators opportunities to conduct research on critical point phenomena in microgravity. This facility provides the high precision and stability temperature standards required in this field of research. It has been primarily designed for the purpose of optical investigations of transparent fluids. During a Spacelab mission, the CPF automatically processes several thermostats sequentially, each thermostat corresponding to an experiment. The CPF is now integrated in Spacelab at Kennedy Space Center, in preparation for the International Microgravity Lab. mission. The CPF was designed to submit transparent fluids to an adequate, user defined thermal scenario, and to monitor their behavior by using thermal and optical means. Because they are strongly affected by gravity, a good understanding of critical phenomena in fluids can only be gained in low gravity conditions. Fluids at the critical point become compressed under their own weight. The role played by gravity in the formation of interfaces between distinct phases is not clearly understood.

Source record↗
NASA NTRS1992

The Microgravity Isolation Mount (MGIM): A Columbus facility for improving the microgravity quality of payloads

The Microgravity Isolation Mount (MGIM) is a facility for providing active vibration isolation for sensitive experiments on the Columbus Attached Laboratory and the Columbus Free-Flying Laboratory. The facility is designed to be accommodated in a standard Columbus rack, and it iterfaces with existing rack utility services. The design is based on a non-contact strategy, whereby the payload 'floats' inside the rack, and its position is controlled by a number of magnetic actuators. The main advantage of using this non-contact strategy is the improved microgravity quality available. The overall design of the facility and a description of its elements are given.

Owen, R. G.↗
NASA NTRS1992

Future aerospace ground test facility requirements for the Arnold Engineering Development Center

Arnold Engineering Development Center (AEDC) was conceived at the close of World War II, when major new developments in flight technology were presaged by new aerodynamic and propulsion concepts. During the past 40 years, AEDC has played a significant part in the development of many aerospace systems. The original plans were extended through the years by some additional facilities, particularly in the area of propulsion testing. AEDC now has undertaken development of a master plan in an attempt to project requirements and to plan for ground test and computational facilities over the coming 20 to 30 years. This report was prepared in response to an AEDC request that the National Research Council (NRC) assemble a committee to prepare guidance for planning and modernizing AEDC facilities for the development and testing of future classes of aerospace systems as envisaged by the U.S. Air Force.

Kirchner, Mark E.↗
NASA NTRS1992

Overview of the NASA Dryden Flight Research Facility aeronautical flight projects

Several principal aerodynamics flight projects of the NASA Dryden Flight Research Facility are discussed. Key vehicle technology areas from a wide range of flight vehicles are highlighted. These areas include flight research data obtained for ground facility and computation correlation, applied research in areas not well suited to ground facilities (wind tunnels), and concept demonstration.

Meyer, Robert R., Jr.↗
NASA NTRS1992

A free-piston Stirling engine/linear alternator controls and load interaction test facility

A test facility at LeRC was assembled for evaluating free-piston Stirling engine/linear alternator control options, and interaction with various electrical loads. This facility is based on a 'SPIKE' engine/alternator. The engine/alternator, a multi-purpose load system, a digital computer based load and facility control, and a data acquisition system with both steady-periodic and transient capability are described. Preliminary steady-periodic results are included for several operating modes of a digital AC parasitic load control. Preliminary results on the transient response to switching a resistive AC user load are discussed.

Rauch, Jeffrey S.↗
NASA NTRS1992

Low power arcjet test facility impacts

Performance characterization of a flight-type 1.4 kW arcjet system were conducted at the Rocket Research Company (RRC) in Redmond, WA, and at the NASA LeRC in Cleveland, OH. The objectives of these tests were as follows: to compare low-power arcjet performance at two different test facilities; to compare arcjet performance obtained with a 2:1 mixture of gaseous hydrogen and nitrogen and hydrazine; and to quantify the effects of test cell pressure on thruster operating characteristics. Performance and thruster temperature distributions were measured at thruster input power levels and propellant mass flow rates ranging from 1274 to 1370 W and from 3.2 x 10(exp -5) to 5.1 x 10(exp -5) kg/s, respectively. Specific impulses measured at the two facilities, at comparable test cell pressures, using gaseous hydrogen-nitrogen propellant mixtures agreed to within 1 percent over the range of operating conditions tested. The specific impulses measured using hydrazine propellant were higher than that for the cold hydrogen-nitrogen mixtures. Agreement between by hydrazine and gas mixture data was good, however, when the differences in propellant enthalpies at the thruster inlet were considered. Specific impulse showed a strong dependence on test facility pressure, and was 3 to 4 percent higher below 0.1 Pa than for test cell pressures above 5 Pa.

Morren, W. Earl↗