SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Program detects hardware failure in servosystems by comparing actual servo valve position with predictions of software model. In addition, system will also pick up most computer input/output failures. Process presents faster and more reliable results than previous failure detection methods.
Detailed software and hardware documentation for the Cardiopulmonary Data Acquisition System is presented. General wiring and timing diagrams are given including those for the LSI-11 computer control panel and interface cables. Flowcharts and complete listings of system programs are provided along with the format of the floppy disk file.
The Space Shuttle Dynamic Integrated Test (DIT) system is described. The DIT is an open-loop system which makes no attempt to simulate Shuttle sensors, and by which the Shuttle redundancy management system is left unmodified. Open-loop operation is shown to inherently require less computing capacity during a test than the closed-loop alternative. DIT tests have generated a high degree of confidence in the Shuttle hardware, allowing the identification of such problems as a sluggish main fuel valve, which caused a countdown hold seconds before the simulated T-zero, and Main Engine Controller software malfunctions. Attention is given to the combination and substitution of sensor data, the modification of nominal flight software, and the preparation of simulation data. It is noted that greater performance would have been achieved if the interface with DIT had been a design requirement from the outset of Space Shuttle development.
The channel capacity C and the cutoff rate R sub o of two (M + 1)-ary decision rules for noisy M slots/symbol optical pulse position modulation (PPM) with ideal photon counting are computed and compared. Also the values of the optimum thresholds needed to minimize the signal requirements are given. With a minor increase in hardware complexity, the symbol by symbol threshold decision rule is shown to be superior to the slot by slot threshold detection and decision rule in two aspects: first, it saves more than 0.5 dB in signal energy for the very noisy cases of more than one noise photon per slot (for low noise cases it also saves signal energy, but a negligibly small amount). Second, it is more robust to variations in the noise level.
Modifications were designed for the B-737-100 Research Aircraft autobrake system hardware of the Advanced Transport Operating Systems (ATOPS) Program at Langley Research Center. These modifications will allow the on-board flight control computer to control the aircraft deceleration after landing to a continuously variable level for the purpose of executing automatic high speed turn-offs from the runway. A bread board version of the proposed modifications was built and tested in simulated stopping conditions. Test results, for various aircraft weights, turnoff speed, winds, and runway conditions show that the turnoff speeds are achieved generally with errors less than 1 ft/sec.
A design framework for a Mars Rover, intended for missions where a high degree of autonomy is dictated, is presented. The framework provides a logical computing architecture for rover mobility and local navigation subsystem design by defining a set of functional modules and interfaces to facilitate software and hardware specification. The similarities and dissimilarities between the present approach and related architectures for autonomous navigation and robotic control are discussed. An approach is presented for specifying actions to be taken by the mobility and local navigation subsystems of the rover.
The Euler code, designated AIRPLANE, which uses an unstructured tetrahedral mesh was used to compute near-field sonic boom pressure signatures on three modern low sonic boom configurations: the Mach 2, Mach 3, and Haglund models. The TEAM code which uses a multi-zoned structured grid was used to calculate pressure signatures for the Mach 2 model. The computational pressure signatures for the Mach 2 and Mach 3 models are compared with recent experimental data. The computed pressure signatures were extracted at distances less than one body length below the configuration and extrapolated to the experimental distance. The Mach 2 model was found to have larger overpressures off-ground-track than on-ground-track in both computational and experimental results. The correlations with the experiment were acceptable where the signatures were not contaminated by instrumentation and model-support hardware. AIRPLANE was used to study selected modifications to improve the overpressures of the Mach 2 model.
The Sierra College Space Technology Program is currently building their third GAS payload in addition to a small satellite. The project is supported by an ARPA/TRP grant. One aspect of the grant is the design of standard hardware for Get Away Specials (GAS) payloads. A standard structure has been designed and work is progressing on a standard battery box and computer.
Limits on astronomical telescope apertures are being rapidly approached. These limits result from logistics, increasing complexity, and finally budgetary constraints. In an historical perspective, great strides have been made in the area of aperture, adaptive optics, wavefront sensors, detectors, stellar interferometers and image reconstruction. What will be the next advances? Emerging data analysis techniques based on communication theory holds the promise of yielding more information from observational data based on significant computer post-processing. This paper explores some of the current telescope limitations and ponders the possibilities increasing the yield of scientific data based on the migration computer post-processing techniques to higher dimensions. Some of these processes hold the promise of reducing the requirements on the basic telescope hardware making the next generation of instruments more affordable.
There are numerous autopilot systems that are commercially available for small (<100 lbs) UAVs. However, they all share several key disadvantages for conducting aerodynamic research, chief amongst which is the fact that most utilize older, slower, 8- or 16-bit microcontroller technologies. This paper describes the development and testing of a flight control system (FCS) for small UAV s based on a modern, high throughput, embedded processor. In addition, this FCS platform contains user-configurable hardware resources in the form of a Field Programmable Gate Array (FPGA) that can be used to implement custom, application-specific hardware. This hardware can be used to off-load routine tasks such as sensor data collection, from the FCS processor thereby further increasing the computational throughput of the system.
Ignition data for tests with a LOX/methane igniter that utilized a glow plug as the ignition source are presented. The tests were conducted in a vacuum can with thermally conditioned (cold) hardware. Data showing the effects of glow plug geometry, type, and igniter operating conditions are discussed. Comparisons between experimental results and multidimensional, transient computer models are also made.
The need for greater autonomy in platforms such as planetary rovers is driving rapidly to codes that far overwhelm the capabilities of conventional space-qualified single core processors to run them in real-time. However, a new generation of potentially space-qualified 2D "tiled" multi-core microprocessor chips is emerging with significant performance potential. Leveraging such inherently parallel hardware for space platforms requires consideration of both time and power limitations - the latter of which is not normally done in conventional parallel computing. This paper takes one such application, Rockster, and analyzes it for energy usage when ported to a multi-core tiled chip such as may come from the Maestro program. The results demonstrate not only the criticality of memory and interconnect in the energy of real-time parallel codes, but also the effects of possible "energy-aware" changes in partitioning and algorithm design.
Non-optimum factors are used during aerospace conceptual and preliminary design to account for the increased weights of as-built structures due to future manufacturing and design details. Use of higher-fidelity non-optimum factors in these early stages of vehicle design can result in more accurate predictions of a concept s actual weights and performance. To help achieve this objective, non-optimum factors are calculated for the aluminum-alloy gores that compose the ogive and ellipsoidal bulkheads of the Space Shuttle Super-Lightweight Tank propellant tanks. Minimum values for actual gore skin thicknesses and weld land dimensions are extracted from selected production drawings, and are used to predict reference gore weights. These actual skin thicknesses are also compared to skin thicknesses predicted using classical structural mechanics and tank proof-test pressures. Both coarse and refined weights models are developed for the gores. The coarse model is based on the proof pressure-sized skin thicknesses, and the refined model uses the actual gore skin thicknesses and design detail dimensions. To determine the gore non-optimum factors, these reference weights are then compared to flight hardware weights reported in a mass properties database. When manufacturing tolerance weight estimates are taken into account, the gore non-optimum factors computed using the coarse weights model range from 1.28 to 2.76, with an average non-optimum factor of 1.90. Application of the refined weights model yields non-optimum factors between 1.00 and 1.50, with an average non-optimum factor of 1.14. To demonstrate their use, these calculated non-optimum factors are used to predict heavier, more realistic gore weights for a proposed heavy-lift launch vehicle s propellant tank bulkheads. These results indicate that relatively simple models can be developed to better estimate the actual weights of large structures for future launch vehicles.
The Rotating Detonation Rocket Engine has maintained steady development at NASA with many staggering performance advantages demonstrated to date over the state-of-the-art (SOA). The implementation of additive manufacturing and specialized NASA developed alloys have enabled rapid maturation of the technology. Several hot fire test projects have been successfully conducted at Marshall Space Flight Center under an early career initiative project funded by NASA Space Technology Mission Directorate. In addition, a new start Technology Demonstration Mission (TDM) project has been funded to investigate challenges relating to integration of turbomachinery with an RDRE thrust chamber assembly. This engine system demonstration will leverage a methane/oxygen single shaft turbopump with fuel rich gas generator and a 10,000 lbf thrust chamber assembly. The configuration was down selected based on feedback from both US industry collaborators and power balance trades in combination with technical feasibility. To date, industry has identified several use cases for RDRE ranging from thruster to primary launch vehicle propulsion. A wide range of fuel and oxidizers were also identified including but not limited to Methane, Kerosene and other liquid hydrocarbon (LH) fuels, and hydrogen. Recent work at NASA and in partnership with NASA has investigated these major fuels of interest with oxygen, air, and hydrogen peroxide (HTP) for various applications. NASA Marshall has already investigated the use of hydrogen/oxygen, methane/oxygen, kerosene/oxygen, and has plans in partnership with industry and academia to investigate LH/air and LH/HTP. In addition to propellants, hardware geometry has been investigated with some critical lessons learned toward greater theoretical performance over the SOA. To this end, several experimental and computational activities are ongoing to further advance the RDRE towards flight missions. Given the rate of advancement, it is highly likely the technology will be flown in space mission in the coming decade. This work documents and overviews many of these investigations and overviews NASA’s future plans for the technology maturation.
It is shown that a self organizing system has two main components: an organizable physical part, and a programing part. This report presents the organizable part in the form of a programable hardware and its programing language.
Explicit codes are often used to simulate the nonlinear dynamics of large-scale structural systems, even for low frequency response, because the storage and CPU requirements entailed by the repeated factorizations traditionally found in implicit codes rapidly overwhelm the available computing resources. With the advent of parallel processing, this trend is accelerating because of the following additional facts: (a) explicit schemes are easier to parallelize than implicit ones, and (b) explicit schemes induce short range interprocessor communications that are relatively inexpensive, while the factorization methods used in most implicit schemes induce long range interprocessor communications that often ruin the sought-after speed-up. However, the time step restriction imposed by the Courant stability condition on all explicit schemes cannot yet be offset by the speed of the currently available parallel hardware. Therefore, it is essential to develop efficient alternatives to direct methods that are also amenable to massively parallel processing because implicit codes using unconditionally stable time-integration algorithms are computationally more efficient when simulating the low-frequency dynamics of aerospace structures.
A report presents an overview of an architecture for a software-reconfigurable network data processor for a spacecraft engaged in scientific exploration. When executed on suitable electronic hardware, the software performs the functions of a physical layer (in effect, acts as a software radio in that it performs modulation, demodulation, pulse-shaping, error correction, coding, and decoding), a data-link layer, a network layer, a transport layer, and application-layer processing of scientific data. The software-reconfigurable network processor is undergoing development to enable rapid prototyping and rapid implementation of communication, navigation, and scientific signal-processing functions; to provide a long-lived communication infrastructure; and to provide greatly improved scientific-instrumentation and scientific-data-processing functions by enabling science-driven in-flight reconfiguration of computing resources devoted to these functions. This development is an extension of terrestrial radio and network developments (e.g., in the cellular-telephone industry) implemented in software running on such hardware as field-programmable gate arrays, digital signal processors, traditional digital circuits, and mixed-signal application-specific integrated circuits (ASICs).
This paper presents two Computational Fluid Dynamics (CFD) models of the flow in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT). The TDT is a continuous-flow, closed circuit wind tunnel with a 16- by 16-foot slotted test section with cropped corners. The tunnel was originally built as the 19-ft Pressure Tunnel in 1938, but it was converted to the current transonic tunnel in the 1950s, with capabilities to use either air or heavy gas as the test medium. The first computational model describes the generation of an atmospheric-boundary-layer (ABL) profile inside the tunnel. An ABL, which includes both a wind profile and turbulence content, is one of the aerodynamic characteristics affecting the occurrence of wind-induced oscillations for a launch vehicle sitting on a pad. The challenging part of this analysis was modeling the turbulent flow inside the tunnel. This is due to the special ABL-generating hardware that was installed at the entrance of the TDT test section in order to change the downstream velocity profile and to introduce velocity fluctuations into the flow. The second CFD model builds on the computational aeroelastic results that were generated in support of the second Aeroelastic Prediction Workshop (AePW) for the NASA Benchmark Supercritical Wing (BSCW) configuration. During the AePW, the wing-only configuration (classical free-air model) was analyzed. In the current study, the flutter computations were conducted on the configuration as it was mounted in the TDT during the experiment. This includes the wing attached to the splitter plate that was attached to the wind-tunnel walls. The preliminary results show that the wind-tunnel walls marginally affect flutter prediction.