Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AERODYNAMICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Overview of HATP Experimental Aerodynamics Data for the Baseline F/A-18 Configuration

Determining the baseline aerodynamics of the F/A-18 was one of the major objectives of the High-Angle-of-Attack Technology Program (HATP). This paper will review the key data bases that have contributed to our knowledge of the baseline aerodynamics and the improvements in test techniques that have resulted from the experimental program. Photographs are given highlighting the forebody and leading-edge-extension (LEX) vortices. Other data representing the impact of Mach and Reynolds numbers on the forebody and LEX vortices will also be detailed. The level of agreement between different tunnels and between tunnels and flight will be illustrated using pressures, forces, and moments measured on a 0.06-scale model tested in the Langley 7- by 10-Foot High Speed Tunnel, a 0.16-scale model in the Langley 30- by 60-Foot Tunnel, a full-scale vehicle in the Ames 80- by 120-Foot Wind Tunnel, and the flight F/A-18 High Alpha Research Vehicle (HARV). Next, creative use of wind tunnel resources that accelerated the validation of the computational fluid dynamics (CFD) codes will be described. Lastly, lessons learned, deliverables, and program conclusions are presented.

Hall, Robert M.↗

Nonlinear Aerodynamics of Bodies in Coning Motion

A numerical method for computing the nonlinear inviscid flowfield surrounding a body performing coning motion is described. The method permits accurate computation of the aerodynamic moment due to one of the four motions characterizing an arbitrary nonplanar motion. Results of computations for a slender circular cone in coning motion are presented, and show good agreement with experiment for angles of attack up to twice the cone half-angle. The computational results display significant departure of the side moment from the linear theory value with increasing angle of attack, but agree well with experimental measurements. This indicates that the initial nonlinear behavior of the aerodynamic moment is determined primarily by the inviscid flow.

Schiff, Lewis B.↗

Aerodynamic Synthesis of a Centrifugal Impeller Using CFD and Measurements

The performance and flow structure in an unshrouded impeller of approximately 4:1 pressure ratio is synthesized on the basis of a detailed analysis of 3D viscous CFD results and aerodynamic measurements. A good data match was obtained between CFD and measurements using laser anemometry and pneumatic probes. This solidified the role of the CFD model as a reliable representation of the impeller internal flow structure and integrated performance. Results are presented showing the loss production and secondary flow structure in the impeller. The results indicate that while the overall impeller efficiency is high, the impeller shroud static pressure recovery potential is underdeveloped leading to a performance degradation in the downstream diffusing element. Thus, a case is made for a follow-on impeller parametric design study to improve the flow quality. A strategy for aerodynamic performance enhancement is outlined and an estimate of the gain in overall impeller efficiency that might be realized through improvements to the relative diffusion process is provided.

Larosiliere, L. M.↗

Gradient-Based Aerodynamic Shape Optimization Using ADI Method for Large-Scale Problems

A gradient-based shape optimization methodology, that is intended for practical three-dimensional aerodynamic applications, has been developed. It is based on the quasi-analytical sensitivities. The flow analysis is rendered by a fully implicit, finite volume formulation of the Euler equations.The aerodynamic sensitivity equation is solved using the alternating-direction-implicit (ADI) algorithm for memory efficiency. A flexible wing geometry model, that is based on surface parameterization and platform schedules, is utilized. The present methodology and its components have been tested via several comparisons. Initially, the flow analysis for for a wing is compared with those obtained using an unfactored, preconditioned conjugate gradient approach (PCG), and an extensively validated CFD code. Then, the sensitivities computed with the present method have been compared with those obtained using the finite-difference and the PCG approaches. Effects of grid refinement and convergence tolerance on the analysis and shape optimization have been explored. Finally the new procedure has been demonstrated in the design of a cranked arrow wing at Mach 2.4. Despite the expected increase in the computational time, the results indicate that shape optimization, which require large numbers of grid points can be resolved with a gradient-based approach.

Pandya, Mohagna J.↗

Development of In-Fiber Reflective Bragg Gratings as Shear Stress Monitors in Aerodynamic Facilities

Bragg gratings centered at nominal wavelengths of 1290 nm and 1300 run were inscribed in a 9/125 microns germano-silicate optical fiber, using continuous wave frequency doubled Ar+ laser radiation at 244 nm. Such gratings have been used extensively as temperature and strain monitors in smart structures. They have, however, never been used for measuring aerodynamic shear stresses. As a test of their sensitivity as shear stress monitors, a Bragg fiber attached to a metal plate was subjected to laminar flows in a glass pipe. An easily measurable large flow-induced wavelength shift (Delta Lambda(sub B)) was observed in the Bragg reflected wavelength. Thereafter, the grating was calibrated by making one time, simultaneous measurements of Delta Lambda(sub B) and the coefficient of skin friction (C(sub f)) with a skin friction balance, as a function of flow rates in a subsonic wind tunnel. Onset of fan-induced transition in the tunnel flow provided a unique flow rate for correlating Delta Lambda(sub B) and (C(sub f) values needed for computing effective modulus of rigidity (N(sub eff)) of the fiber attached to the metal plate. This value Of N(sub eff) is expected to remain constant throughout the elastic stress range expected during the Bragg grating aerodynamic tests. It has been used for calculating the value of Cf at various tunnel speeds, on the basis of measured values of Bragg wavelength shifts at those speeds.

Parmar, Devendra S.↗

Aerodynamic Parameters of High Performance Aircraft Estimated from Wind Tunnel and Flight Test Data

A concept of system identification applied to high performance aircraft is introduced followed by a discussion on the identification methodology. Special emphasis is given to model postulation using time invariant and time dependent aerodynamic parameters, model structure determination and parameter estimation using ordinary least squares an mixed estimation methods, At the same time problems of data collinearity detection and its assessment are discussed. These parts of methodology are demonstrated in examples using flight data of the X-29A and X-31A aircraft. In the third example wind tunnel oscillatory data of the F-16XL model are used. A strong dependence of these data on frequency led to the development of models with unsteady aerodynamic terms in the form of indicial functions. The paper is completed by concluding remarks.

Klein, Vladislav↗

Parameter Estimation of Actuators for Benchmark Active Control Technology (BACT) Wind Tunnel Model with Analysis of Wear and Aerodynamic Loading Effects

This report describes the development of transfer function models for the trailing-edge and upper and lower spoiler actuators of the Benchmark Active Control Technology (BACT) wind tunnel model for application to control system analysis and design. A simple nonlinear least-squares parameter estimation approach is applied to determine transfer function parameters from frequency response data. Unconstrained quasi-Newton minimization of weighted frequency response error was employed to estimate the transfer function parameters. An analysis of the behavior of the actuators over time to assess the effects of wear and aerodynamic load by using the transfer function models is also presented. The frequency responses indicate consistent actuator behavior throughout the wind tunnel test and only slight degradation in effectiveness due to aerodynamic hinge loading. The resulting actuator models have been used in design, analysis, and simulation of controllers for the BACT to successfully suppress flutter over a wide range of conditions.

Waszak, Martin R.↗

Aerodynamics of a Transitioning Turbine Stator Over a Range of Reynolds Numbers

Midspan aerodynamic measurements for a three vane-four passage linear turbine vane cascade are given. The vane axial chord was 4.45 cm. Surface pressures and loss coefficients were measured at exit Mach numbers of 0.3, 0.7, and 0.9. Reynolds number was varied by a factor of six at the two highest Mach numbers, and by a factor of ten at the lowest Mach number. Measurements were made with and without a turbulence grid. Inlet turbulence intensities were less than I% and greater than IO%. Length scales were also measured. Pressurized air fed the test section, and exited to a low pressure exhaust system. Maximum inlet pressure was two atmospheres. The minimum inlet pressure for an exit Mach number of 0.9 was one-third of an atmosphere, and at a Mach number of 0.3, the minimum pressure was half this value. The purpose of the test was to provide data for verification of turbine vane aerodynamic analyses, especially at low Reynolds numbers. Predictions obtained using a Navier-Stokes analysis with an algebraic turbulence model are also given.

Boyle, R. J.↗

Energy Efficient Engine Low Pressure Subsystem Aerodynamic Analysis

The objective of this study was to demonstrate the capability to analyze the aerodynamic performance of the complete low pressure subsystem (LPS) of the Energy Efficient Engine (EEE). Detailed analyses were performed using three- dimensional Navier-Stokes numerical models employing advanced clustered processor computing platforms. The analysis evaluates the impact of steady aerodynamic interaction effects between the components of the LPS at design and off- design operating conditions. Mechanical coupling is provided by adjusting the rotational speed of common shaft-mounted components until a power balance is achieved. The Navier-Stokes modeling of the complete low pressure subsystem provides critical knowledge of component acro/mechanical interactions that previously were unknown to the designer until after hardware testing.

Hall, Edward J.↗

Aerodynamic Characteristics at Mach Number 2.05 of a Series of Highly Swept Arrow Wings Employing Various Degrees of Twist and Camber

A series of arrow wings employing various degrees of twist and camber were tested in the Langley 4- by 4-foot supersonic pressure tunnel. Aerodynamic forces and moments in pitch were measured at a Mach number of 2.05 and at a Reynolds number of 4.4 x 10(exp 6) based on the mean aerodynamic chord. Three of the wings, having a leading-edge sweep angle of 70 deg. and an aspect ratio of 2.24, were designed to produce a minimum drag (in comparison with that produced for other wings in the family) at lift coefficients of 0. 0.08, and 0.16. A fourth and a fifth wing, having a 75 deg. swept leading edge and an aspect ratio of 1.65, were designed for lift coefficients of 0 and 0.16, respectively. A 70 deg. swept arrow wing with twist and camber designed for an optimum loading at a lift coefficient considerably less than that for maximum lift-drag ratio gave the highest lift-drag ratio of all the wings tested a value of 8.8 compared with a value of 8.1 for the corresponding wing without twist and camber. Two twisted and cambered wings designed for optimum loading at the lift coefficient for maximum lift-drag ratio gave only small increases in maximum lift-drag ratios over that obtained for the corresponding flat wings. However, in all cases, the lift-drag ratios obtained were far below the theoretical estimates.

Carlson, Harry W.↗

Elevated-Temperature Tests Under Static and Aerodynamic Conditions on Honeycomb-Core Sandwich Panels

Stainless-steel honeycomb-core sandwich panels which differed primarily in skin thicknesses were tested at elevated temperatures under static and aerodynamic conditions. The results of these tests were evaluated to determine the insulating effectiveness and structural integrity of the panels. The static radiant-heating tests were performed in front of a quartz-tube radiant heater at panel skin temperatures up to 1,5000 F. The aerodynamic tests were made in a Mach 1.4 heated blowdown wind tunnel. The tunnel temperature was augmented by additional heat supplied by a radiant heater which raised the panel surface temperature above 8000 F during air flow. Static radiant-heating tests of 2 minutes duration showed that all the panels protected the load-carrying structure about equally well. Thin-skin panels showed an advantage for this short-time test over thick-skin panels from a standpoint of weight against insulation. Permanent inelastic strains in the form of local buckles over each cell of the honeycomb core caused an increase in surface roughness. During the aero- dynamic tests all of the panels survived with little or no damage, and panel flutter did not occur.

Groen, Joseph M.↗

Elevated-Temperature Tests Under Static and Aerodynamic Conditions on Corrugated-Stiffened Panels

Thermal-insulating panels made of 0.005-inch-thick corrugated-stiffened sheets of Inconel X, backed by either bulk or reflective insulation, were tested under static and aerodynamic conditions at elevated temperatures up to 1,8000 F in front of a quartz-tube radiant heater and in a blowdown wind tunnel at a Mach number of 1.4. The tests were performed to provide information on the structural integrity and insulating effectiveness of thermal-insulating panels under the effects of aerodynamic heating. Static radiant-heating tests showed that the bulk insulation protected a load-carrying structure better than did the reflective insulation; however, the bulk insulation was much heavier than the reflective insulation and made the panel assemblies about three times as thick. Three of the four panels tested in the heated supersonic wind tunnel fluttered and failed dynamically. However, one panel demonstrated that flutter can be alleviated considerably with proper edge support. The panels deflected toward the heater (or into the airstream) at a rate which was primarily dependent on the temperature difference through the panel thickness.

Groen, Joseph M.↗

An Approximate Analytical Method for Studying Atmosphere Entry of Vehicles with Modulated Aerodynamic Forces

The dimensionless, transformed, nonlinear differential equation developed in NASA TR R-11 for describing the approximate motion and heating during entry into planetary atmospheres for constant aerodynamic coefficients and vehicle shape has been modified to include entries during which the aerodynamic coefficients and the vehicle shape are varied. The generality of the application of the original equation to vehicles of arbitrary weight, size, and shape and to arbitrary atmospheres is retained. A closed-form solution for the motion, heating, and the variation of drag loading parameter m/C(D)A has been obtained for the case of constant maximum resultant deceleration during nonlifting entries. This solution requires certain simplifying assumptions which do not compromise the accuracy of the results. The closed-form solution has been used to determine the variation of m/C(D)A required to reduce peak decelerations and to broaden the corridor for nonlifting entry into the earth's atmosphere at escape velocity. The attendant heating penalty is also studied.

Levy, Lionel L., Jr.↗

Aerodynamic Characteristics, Temperature, and Noise Measurements of a Large-Scale External-Flow Jet-Augmented-Flap Model with Turbojet Engines Operating

An investigation has been conducted in the Langley full-scale tunnel on a large-scale model powered by turbojet engines with flattened rectangular nozzles. The wing had 35 deg. sweep of the leading edge, an aspect ratio of 6.5, a taper ratio of 0.31, and NACA 65(1)-412 and 65-408 airfoils at the root and tip. The investigation included measurements of the longitudinal aerodynamic characteristics of the model with half-span and full-span flaps and measurements of the sound pressure and skin temperature on the portions of the lower surface of the wing immersed in the jet flow. The tests were conducted over a range or angles of attack from -8 to 16 deg. for Reynolds numbers from 1.8 x 10(exp 6) to 4.4 x 10(exp 6) and a range of momentum coefficients from 0 to 2.0. In general, the aerodynamic results of this investigation made with a large-scale hot-jet model verified the results of previous investigations with small models powered by compressed-air jets. Although blowing was only done over the inboard portion of the wing, substantial amounts of induced lift were also obtained over the outboard portion of the wing. Skin temperatures were about 340 F and wing heating could be handled with available materials without cooling. Random acoustic loadings on the wing surface were high enough to indicate that fatigue failure from this source would require special consideration in the design of an external-flow jet flap system for an airplane.

Fink, Marvin P.↗

Aerodynamic Loading Characteristics Including Effects of Aeroelasticity of a Thin-Trapezoidal-Wing-Body Combination at Mach Number of 1.43

Results have been obtained in the Langley 8-foot transonic pressure tunnel at a Mach number of 1.43 and at angles of attack from 0 deg to about 24 deg which indicate the static-aerodynamic-loads characteristics for a 2-percent-thick trapezoidal wing in combination with a body. Included are the effects of changing Reynolds number and of fixing boundary-layer transition. The results show that aerodynamic loading characteristics at a Mach number of 1.43 are similar to those reported in NACA RM L56Jl2a for the same configuration at a Mach number of 1.115. Reducing the Reynolds number resulted in reductions in the deflection of the wing and caused a slight increase in the relative loading over the outboard wing sections since the deflections were in a direction to unload the tip sections. Little or no effects were seen to result from fixing boundary-layer transition at a tunnel stagnation pressure of 1,950 pounds per square foot.

Kelly, Thomas C.↗

Aerodynamic Characteristics of a Four-Propeller Tilt-Wing VTOL Model with Twin Vertical Tails, Including Effects of Ground Proximity

Results are presented of a wind-tunnel investigation of the aerodynamic stability, control, and performance characteristics of a model of a four-propeller tilt-wing VTOL airplane employing flaps and speed brakes through the transition speed range. The results indicate that the wing was stalled for steady level flight for all conditions of the investigation; however, the flapped configuration did produce a higher maximum lift. The effectiveness of the flap in delaying the stall in the present investigation was not as great as in some previous investigations because the flap used was smaller than that used previously. The wing stall resulted in an appreciable reduction of aileron effectiveness during the transition. Out of ground effect the low horizontal tail did not appear to be in an adverse flow field as had been expected and showed no erratic changes in effectiveness; however, in ground effect a large nose-down moment was experienced by the model. In general, the lateral aerodynamic data indicate that the configuration is directionally stable and possesses positive dihedral effect throughout the transition, and the data show no signs of erratic flow at the vertical tails.

Grunwald, Kalman J.↗

The Longitudinal Aerodynamic Characteristics of a Sweptback Wing-Body Combination With and Without End Plates at Mach Numbers from 0.40 to 0.93

An investigation was made at high subsonic speeds in the Langley high-speed 7- by 10-foot tunnel to determine the effect of end plates on the longitudinal aerodynamic characteristics of a sweptback wing-body combination with and without drooped chord-extensions. The wing had 45 deg sweepback of the quarter-chord line, an aspect ratio of 4, a taper ratio of 0.3, and NACA 65AO06 airfoil sections parallel to the plane of symmetry, and was mounted near the rear of a body of revolution having a fineness ratio of approximately 8. The results indicated that the addition of the end plates to either the wing with drooped chord-extensions or to the wing without drooped chord-extensions slightly increased the lift in the low angle-of-attack range but slightly decreased the lift at moderate and high angles of attack. The addition of the end plates to the wing without the chord-extensions caused a small increase in the maximum lift-drag ratio at Mach numbers below 0.65 and a slight decrease at the higher Mach numbers; however, for the addition of the end plates to the wing with the chord- extensions the maximum lift-drag ratio was slightly decreased below a Mach number of 0.88, while a slight increase occurred for the higher Mach numbers. The addition of the end plates to the wings with and without the chord-extensions caused the static longitudinal stability to increase considerably for all Mach numbers; however, only a slight reduction in the aerodynamic-center variation with Mach number was observed.

Henderson, William P.↗

Wind-Tunnel Investigation of Subsonic Longitudinal Aerodynamic Characteristics of a Tiltable-Wing Vertical-Take-Off-and-Landing Supersonic Bomber Configuration Including Turbojet Power Effects

Jet-powered model tests were made to determine the low-speed longitudinal aerodynamic characteristics of a vertical-take-off and-landing supersonic bomber configuration. The configuration has an unique engine-wing arrangement wherein six large turbojet engines (three on each side of the fuselage) are buried in a low-aspect-ratio wing which is tilted into the vertical plane for take-off. An essentially two-dimensional variable inlet, spanning the leading edge of each wing semispan, provides air for the engines. Jet flow conditions were simulated for a range of military (nonafterburner) and afterburner turbojet-powered flight at subsonic speeds. Three horizontal tails were tested at a station down-stream of the jet exit and at three heights above the jet axes. A semi-span model was used and test parameters covered wing-fuselage incidence angles from 0 deg to 15 deg, wing angles of attack from -4 deg to 36 deg, a variable range of horizontal-tail incidence angles, and some variations in power simulation conditions. Results show that, with all horizontal tails tested, there were large variations in static stability throughout the lift range. When the wing and fuselage were alined, the model was statically stable throughout the test range only with the largest tail tested (tail span of 1.25 wing span) and only when the tail was located in the low test position which placed the tail nearest to the undeflected jet. For transition flight conditions, none of the tail configurations provided satisfactory longitudinal stability or trim throughout the lift range. Jet flow was destabilizing for most of the test conditions, and varying the jet-exit flow conditions at a constant thrust coefficient had little effect on the stability of this model. Wing leading-edge simulation had some important effects on the longitudinal aerodynamic characteristics.

Thompson, Robert F.↗