SEARCH · Engineering Papers

Results for “test configuration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Computational study of wind-tunnel wall effects on flow field around delta wings

This paper addresses wind-tunnel wall effects on delta-wing flow fields using the Free Vortex Sheet (FVS) theory in support of planned subsonic wind-tunnel tests. The configurations include several sizes of a 65-deg delta wing in the NASA Langley Research Center Low-Turbulence Pressure Tunnel (LTPT), and an aspect ratio 1 delta wing in the Delft University low-speed tunnel. Standard upflow correction methodology is extended to account for angle-of-attack and nonplanar effects. Blockage and streamline curvature corrections are not applied in the present investigation. Resulting corrections to the 65-deg delta flow field were good for model-to-tunnel span ratios up to 0.5 and angles of attack up to 30-deg, both for linear attached flow and nonlinear vortex flow. For the aspect ratio 1 delta wing, corrections to the vortex flow field for the effect of the averaged upflow angle were satisfactory but streamline curvature effects were larger.

Frink, Neal T.↗

NASA NTRS1987

Characteristics of a separating confluent boundary layer and the downstream wake

Measurements of pressure and velocity characteristics are presented and analyzed for flow over and downstream of a NACA 4412 airfoil equipped with a NACA 4415 single-slotted flap at high angle of attack and close to maximum lift. The flow remained attached over the main element while a large region of recirculating flow occurred over the aft 61 percent of the flap. The airfoil configuration was tested at a Mach number of 0.09 and a chord Reynolds number of 1.8x10 to the 6th power in the NASA Ames Research Center 7- by 10-Foot Wind Tunnel. Measurement of mean and fluctuation velocities were obtained in regions of recirculation and high turbulence intensity using 3-D laser velocimetry. In regions where the flow had a preferred direction and relatively low turbulence intensity, hot-wire anemometry was used. Emphasis was placed on obtaining characteristics in the confluent boundary layer, the region of recirculating flow, and in the downstream wake. Surface pressure measurements were made on the main airfoil, flap, wind tunnel roof and floor. It is thought likely that because the model is large when compared to the wind tunnel cross section, the wind tunnel floor and ceiling interference should be taken into account when the flow field is calculated.

Adair, Desmond↗

NASA NTRS1988

Thermostructural analysis of simulated cowl lips

Three dimensional finite element analyses using MSC/NASTRAN and MARC are performed to predict the thermal and structural response of various cooling schemes under high heat loads. Steady state heat transfer analyses and elastic stress analyses are performed using MSC/NASTRAN. Elastic/plastic analyses are done using MARC. To help verify these analyses experimentally, a hydrogen-oxygen rocket engine was modified to use the exhaust stream as a high enthalpy, high heat flux source to evaluate various actively cooled, simulated cowl lip (leading edges) segments as well as flat structural segments. Cross flow and parallel flow cooling configurations were tested and analyzed using cooling fluids of water and gaseous hydrogen. In addition, various material types, including high conductivity copper, nickel, and a copper and graphite metal matrix composite were tested and compared.

Melis, Matthew E.↗

NASA NTRS1988

Characteristics of merging shear layers and turbulent wakes of a multi-element airfoil

Flow characteristics in the vicinity of the trailing edge of a single-slotted airfoil flap are presented and analyzed. The experimental arrangement consisted of a NACA 4412 airfoil equipped with a NACA 4415 flap whose angle of deflection was 21.8 deg. The flow remained attached over the model surfaces except in the vicinity of the flap trailing edge where a small region of boundary-layer separation extended over the aft 7 percent of flap chord. The flow was complicated by the presence of a strong, initially inviscid jet emanating from the slot between airfoil and flap, and a gradual merging of the main airfoil wake and flap suction-side boundary layer. Downstream of the flap, the airfoil and flap wakes fully merged to form an asymmetrical curved wake. The airfoil configuration was tested at an angle of attack of 8.2 deg, at a Mach number of 0.09, and a chord based Reynolds number of 1.8 x 10 to the 6th power in the Ames Research Center 7- by 10-Foot Wind Tunnel. Surface pressure measurements were made on the airfoil and flap and on the wind tunnel roof and floor. It was estimated that the wall interference increased the C sub L by 7 percent and decreased the C sub M by 4.5 percent. Velocity characteristics were quantified using hot-wire anemometry in regions of flow with preferred direction and low turbulence intensity. A 3-D laser velocimeter was used in regions of flow recirculation and relatively high turbulence intensity.

Adair, Desmond↗

NASA NTRS1988

Space shuttle phase B wind tunnel model and test information. Volume 3: Launch configuration

Archived wind tunnel data are available for flyback booster or other alternative recoverable configurations as well as reusable orbiters studied during initial development (Phase B) of the Space Shuttle. Considerable wind tunnel data was acquired by the competing contractors and the NASA Centers for an extensive variety of configurations with an array of wing and body planforms. All contractor and NASA wind tunnel data acquired in the Phase B development have been compiled into a data base and are available for application to current winged flyback or recoverable booster aerodynamic studies. The Space Shuttle Phase B Wind Tunnel Database is structured by vehicle component and configuration type. Basic components include booster, orbiter and launch vehicle. Booster configuration types include straight and delta wings, canard, cylindrical, retroglide and twin body. Orbital configuration types include straight and delta wings, lifting body, drop tanks and double delta wings. This is Volume 3 (Part 2) of the report -- Launch Configuration -- which includes booster and orbiter components in various stacked and tandem combinations.

Glynn, J. L.↗

NASA NTRS1987

Noise characteristics of model counter-rotating Prop-Fans

Results of acoustics tests of 24.5 in. diameter model counter-rotating propfans are presented. In these tests several configurations were investigated, including tractors and pushers downstream of a pylon, both at zero degrees and at four degrees angle-of-attack. The effects on noise of spacing between rotors and between the pylon and the rotors were also measured. Effects of rotor spacing were found to cause small changes in noise. Increasing blade count from 5-front and 5-rear to 6-front and 6-rear results in about a 1 EPNdB reduction in noise. Increasing only the front rotor blade count to six blades resulted in a noise reduction of about 2 EPNdB. The presence of the pylon resulted in a 1 EPNdB increase in noise. Angle of attack effects showed an increase of 3.5 EPNdB for the tractor configuration and only 1.5 EPNdB for the pusher configuration. Tip speed was found to be the strongest parameter in reducing noise. However, for a given thrust loading, an optimum tip speed is seen. Correlations between measurements and predictions are shown to be in good agreement.

Magliozzi, B.↗

NASA NTRS1988

Turbulent separated flow in the vicinity of a single-slotted airfoil flap

Detailed measurements of pressure and velocity characteristics are presented and analyzed for flow over and downstream of a NACA 4412 airfoil equipped with a NACA 4415 single-slotted flap at high angle of attack and close to maximum lift. The flow remained attached over the main element while a large region of recirculating flow occurred over the aft 61 percent of the flap. The airfoil configuration was tested at a Mach number of 0.09 and chord based Reynolds number of 1.8 x 10 to the 6th in the NASA Ames Research Center 7- by 10-Foot Wind Tunnel. Measurements of mean and fluctuating velocities were obtained in the region of recirculation and high turbulence intensity using three-dimensional laser velocimetry. In regions where the flow had a preferred direction and relatively low turbulence intensity hot-wire anemometry was used. Emphasis was placed on obtaining flow characteristics in the confluent boundary layer, the region of recirculating flow and in the downstream wake. Surface pressure measurements were made on the main airfoil, flap, wind tunnel roof, and wind tunnel floor. In addition to the presentation of pressure and velocity characteristics, the near wall results inside the separated region are analyzed as are the relative importance of terms in the momentum and turbulence kinetic energy equations in the confluent separated boundary layer and the recirculating region of the near wake.

Adair, Desmond↗

NASA NTRS1988

A forecast of new test capabilities using Magnetic Suspension and Balance Systems

This paper outlines the potential of Magnetic Suspension and Balance System (MSBS) technology to solve existing problems related to support interference in wind tunnels. Improvement of existing test techniques and exciting new techniques are envisioned as a result of applying MSBS. These include improved data accuracy, dynamic stability testing, two-body/stores release testing, and pilot/designer-in-the-loop tests. It also discusses the use of MSBS for testing exotic configurations such as hybrid hypersonic vehicles. A new facility concept that combines features of ballistic tubes, magnetic suspension, and cryogenic tunnels is described.

Lawing, Pierce L.↗

NASA NTRS1989

Eight-Bit-Slice GaAs General Processor Circuit

Novel GaAs 8-bit slice enables quick and efficient implementation of variety of fast GaAs digital systems ranging from central processing units of computers to special-purpose processors for communications and signal-processing applications. With GaAs 8-bit slice, designers quickly configure and test hearts of many digital systems that demand fast complex arithmetic, fast and sufficient register storage, efficient multiplexing and routing of data words, and ease of control.

Weissman, John↗

NASA NTRS1988

A water tunnel study of Gurney flaps

Several Gurney flap configurations were tested in the NASA Langley 16 x 24 inch Water Tunnel. These devices provided an increased region of attached flow on a wing upper surface relative to the wing without the flaps. The recirculation region behind the flap was visualized and shown to be consistent with hypotheses stated in previous research. Although the test Reynolds number for this study was several orders of magnitude below those in previous investigations, the effect of the Gurney flaps is in qualitative agreement with them. This is as would be expected from first order effects for high lift devices.

Neuhart, Dan H.↗

NASA NTRS1987

High performance architecture for robot control

Practical aspects of the design and implementation of a modular, high performance, parallel computer control system for telerobots are discussed. Topics of consideration include system architecture, operator interface, and control execution. In a laboratory environment, a telerobotics test control configuration is used to obtain measurements on communications and control loop timing for use in an effective full scale operational system design. The feasibility of the selected architectural approach has been successfully demonstrated. The modularity of the software and hardware enables ease of transport for use in the operational system. The distributed partioning of the control algorithms and the performance measurements acquired during control system implementation are discussed.

Byler, E.↗

NASA NTRS1989

Fracture toughness of SiC/Al metal matrix composite

An experimental study was conducted to evaluate fracture toughness of SiC/Al metal matrix composite (MMC). The material was a 12.7 mm thick extrusion of 6061-T6 aluminum alloy with 40 v/o SiC particulates. Specimen configuration and test procedure conformed to ASTM E399 Standard for compact specimens. It was found that special procedures were necessary to obtain fatigue cracks of controlled lengths in the preparation of precracked specimens for the MMC material. Fatigue loading with both minimum and maximum loads in compression was used to start the precrack. The initial precracking would stop by self-arrest. Afterwards, the precrack could be safely extended to the desired length by additional cyclic tensile loading. Test results met practically all the E399 criteria for the calculation of plane strain fracture toughness of the material. A valid K sub IC value of the SiC/Al composite was established as K sub IC = 8.9 MPa square root of m. The threshold stress intensity under which crack would cease to grow in the material was estimated as delta K sub th = 2MPa square root of m for R = 0.09 using the fatigue precracking data. Fractographic examinations show that failure occurred by the micromechanism involved with plastic deformation although the specimens broke by brittle fracture. The effect of precracking by cyclic loading in compression on fracture toughness is included in the discussion.

Flom, Yury↗

NASA NTRS1988

Transmission loss of double wall panels containing Helmholtz resonators

Data and an analysis are presented on the use of Helholtz resonators in double wall panels (i.e., aircraft sidewalls). Several wall materials and resonator configurations were tested, and the resonators were found to substantially increase the transmission loss of the double wall system at the tuning frequency.

Prydz, R. A.↗

NASA NTRS1989

On the computation of shock shapes in nonequilibrium hypersonic flows

Several models using different descriptions of high temperature air are used to compute the bow shock shapes on experimental model configurations. The test conditions result in nonequilibrium chemical reaction and thermal excitation of the gas which has a first-order effect on the shock shapes. The computed results are compared to experiment and demonstrate that the model using seven chemical species and six temperatures predicts the experimental shock shapes very well. The other gas models, including perfect gas, equilibrium gas and one-temperature chemical nonequilibrium models are less accurate. The results illustrate the necessity of including both thermal and chemical nonequilibrium in the description of the gas. The use of these experimental data makes it possible to verify aspects of current and future chemically reacting flow algorithms.

Candler, Graham↗

NASA NTRS1989

Measured and predicted aerodynamic heating on a cylinder in wake of AFE configuration at incidence

Thin-film resistance gages were used to measure cylinder surface heat-transfer rates in the near wake of the Aeroassist Flight Experiment vehicle configuration, while surface-streamline directions were ascertained by the oil-flow techniques under the same configuration and test conditions. Both heat transfer distributions and flow over the entire cylinder surface were influenced by impingement of that portion of the free shear layer originating at the forebody shoulder in the upper symmetry plane. Heating rate distributions predicted with a Navier-Stokes solver computer code were in general agreement with measurements.

Wells, William L.↗

NASA NTRS1990

Airdata calibration of a high-performance aircraft for measuring atmospheric wind profiles

The research airdata system of an instrumented F-104 aircraft has been calibrated to measure winds aloft in support of the space shuttle wind measurement investigation at the National Aeronautics and Space Administration Ames Research Center Dryden Flight Research Facility. For this investigation, wind measurement accuracies comparable to those obtained from Jimsphere balloons were desired. This required an airdata calibration more accurate than needed for most aircraft research programs. The F-104 aircraft was equipped with a research pilot-static noseboom with integral angle-of-attack and flank angle-of-attack vanes and a ring-laser-gyro inertial reference unit. Tower fly-bys and radar acceleration-decelerations were used to calibrate Mach number and total temperature. Angle of attack and angle of sideslip were calibrated with a trajectory reconstruction technique using a multiple-state linear Kalman filter. The F-104 aircraft and instrumentation configuration, flight test maneuvers, data corrections, calibration techniques, and resulting calibrations and data repeatability are presented. Recommendations for future airdata systems on aircraft used to measure winds aloft are also given.

Haering, Edward A., Jr.↗

NASA NTRS1989

Turbulent separated flow over and downstream of a two-element airfoil

Flow characteristics in the vicinity of the flap of a single-slotted airfoil are presented and analyzed. The flow remained attached over the model surfaces, except in the vicinity of the flap trailing edge where a small region of boundary-layer separation extended over the aft 7 percent of flap chord. The airfoil configuration was tested at a Mach number of 0.09 and a chord Reynolds number of 1.8 x 10 to the 6th in the NASA Ames Research Center 7- by 10-Foot Wind Tunnel. The flow was complicated by the presence of a strong, initially inviscid, jet, emanating from the slot between airfoil and flap, and a gradual merging of the main airfoil wake and flap suction-side boundary layer.

Adair, D.↗

NASA NTRS1990

Airdata calibration of a high-performance aircraft for measuring atmospheric wind profiles

The research airdata system of an instrumented F-104 aircraft has been calibrated to measure winds aloft in support of the Space Shuttle wind measurement investigation. The F-104 aircraft was equipped with a research pitot-static noseboom with integral angle-of-attack and flank angle-of-attack vanes and a ring-laser-gyro inertial reference unit. The F-104 aircraft and instrumentation configuration, flight test maneuvers, data corrections, calibration techniques, and resulting calibrations and data repeatability are presented. Recommendations for future airdata systems on aircraft used to measure winds aloft are also given.

Haering, Edward A., Jr.↗