Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “measurement errors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Gravity and the geoid in the Nepal Himalaya

Materials within the Himalaya are rising due to convergence between India and Asia. If the rate of erosion is comparable to the rate of uplift the mean surface elevation will remain constant. Any slight imbalance in these two processes will lead to growth or attrition of the Himalaya. The process of uplift of materials within the Himalaya coupled with surface erosion is similar to the advance of a glacier into a region of melting. If the melting rate exceeds the rate of downhill motion of the glacier then the terminus of the glacier will receed up-valley despite the downhill motion of the bulk of the glacier. Thus although buried rocks, minerals and surface control points in the Himalaya are undoubtably rising, the growth or collapse of the Himalaya depends on the erosion rate which is invisible to geodetic measurements. Erosion rates are currently estimated from suspended sediment loads in rivers in the Himalaya. These typically underestimate the real erosion rate since bed-load is not measured during times of heavy flood, and it is difficult to integrate widely varying suspended load measurements over many years. An alternative way to measure erosion rate is to measure the rate of change of gravity in a region of uplift. If a control point moves vertically it should be accompanied by a reduction in gravity as the point moves away from the Earth's center of mass. There is a difference in the change of gravity between uplift with and without erosion corresponding to the difference between the free-air gradient and the gradient in the acceleration due to gravity caused by a corresponding thickness of rock. Essentially gravity should change precisely in accord with a change in elevation of the point in a free-air gradient if erosion equals uplift rate. We were funded by NASA to undertake a measurement of absolute gravity simultaneously with measurements of GPS height within the Himalaya. Since both absolute gravity and time are known in an absolute sense to 1 part in 10(exp 10) it is possible to estimate gravity with a precision of 0.1 mu gal. Known systematic errors reduce the measurement to an absolute uncertainty of 6 mu gal. The free air gradient at the point of measurement is typically about 3 mu gals/cm. At Simikot where our experiment was conducted we determined a vertical gravity gradient of 4.4 mu gals/cm.

Bilham, Roger↗
NASA NTRS2011

Application of Commercial Non-Dispersive Infrared Spectroscopy Sensors for Sub-Ambient Carbon Dioxide Detection

Monitoring carbon dioxide (CO2) concentration within a spacecraft or spacesuit is critically important to ensuring the safety of the crew. Carbon dioxide uniquely absorbs light at wavelengths of 3.95 micrometers and 4.26 micrometers. As a result, non-dispersive infrared (NDIR) spectroscopy can be employed as a reliable and inexpensive method for the quantification of CO2 within the atmosphere. A multitude of commercial-off-the-shelf (COTS) NDIR sensors exist for CO2 quantification. The COTS sensors provide reasonable accuracy so long as the measurements are attained under conditions close to the calibration conditions of the sensor (typically 21.1 C and 1 atm). However, as pressure deviates from atmospheric to the pressures associated with a spacecraft (8.0-10.2 PSIA) or spacesuit (4.1-8.0 PSIA), the error in the measurement grows increasingly large. In addition to pressure and temperature dependencies, the infrared transmissivity through a volume of gas also depends on the composition of the gas. As the composition is not known a priori, accurate sub-ambient detection must rely on iterative sensor compensation techniques. This manuscript describes the development of recursive compensation algorithms for sub-ambient detection of CO2 with COTS NDIR sensors. In addition, the basis of the exponential loss in accuracy is developed theoretically considering thermal, Doppler, and Lorentz broadening effects which arise as a result of the temperature, pressure, and composition of the gas mixture under analysis. As a result, this manuscript provides an approach to employing COTS sensors at sub-ambient conditions and may also lend insight into designing future NDIR sensors for aerospace application.

Swickrath, Michael J.↗
NASA NTRS2005

Hubble Space Telescope Angular Velocity Estimation During the Robotic Servicing Mission

In 2004 NASA began investigation of a robotic servicing mission for the Hubble Space Telescope (HST). Such a mission would require estimates of the HST attitude and rates in order to achieve a capture by the proposed Hubble robotic vehicle (HRV). HRV was to be equipped with vision-based sensors, capable of estimating the relative attitude between HST and HRV. The inertial HST attitude is derived from the measured relative attitude and the HRV computed inertial attitude. However, the relative rate between HST and HRV cannot be measured directly. Therefore, the HST rate with respect to inertial space is not known. Two approaches are developed to estimate the HST rates. Both methods utilize the measured relative attitude and the HRV inertial attitude and rates. First, a nonlinear estimator is developed. The nonlinear approach estimates the HST rate through an estimation of the inertial angular momentum. The development includes an analysis of the estimator stability given errors in the measured attitude. Second, a linearized approach is developed. The linearized approach is a pseudo-linear Kalman filter. Simulation test results for both methods are given, including scenarios with erroneous measured attitudes. Even though the development began as an application for the HST robotic servicing mission, the methods presented are applicable to any rendezvous/capture mission involving a non-cooperative target spacecraft.

Thienel, Julie K.↗
NASA NTRS1980

The effect of directional radiation models on the interpretation of earth radiation budget measurements

A parameter estimation technique is presented to estimate the radiative flux density distribution over the earth from a set of radiometer measurements at satellite altitude. The technique analyzes measurements from a wide field of view, horizon to horizon, nadir pointing sensor with a mathematical technique to derive the radiative flux density estimates at the top of the atmosphere for resolution elements smaller than the sensor field of view. A computer simulation of the data analysis technique is presented for both earth-emitted and reflected radiation. The errors resulting from the assumed directional radiation model, spatial model and random measurement error have little effect on the global mean radiation. Zonal estimates were found to be more sensitive to the spatial model than to the directional radiation model. Results from analyzing medium field of view measurements showed a much greater sensitivity to the directional radiation model even on a global scale.

Green, R. N.↗
NASA NTRS1986

Factor of 2 error in balloon-borne atmospheric conduction current measurements

An exact expression is derived for the atmospheric current to a prolate spheroidal antenna. The effective collection area is considered, obtaining a solution for a spherical antenna and the vertical wire antenna. A factor of two error in the studies of the effective area of an antenna of arbitrary geometry by Kasemir and Ruhnke (1958) and Ogawa (1973) is discussed. The effects of the instrument-atmospheric interaction as they apply to the atmospheric conduction current measurement are considered. Electric field enhancement factors for spheroids and approximate solutions for spheroids and other elongated objects are given.

Few, A. A.↗
DOE OSTI2022

Test of nuclear decay rate variation due to an antineutrino flux

Unexplained variations of the decay rate parameter for weak interaction decays such as β ± decay, electron capture, as well as strong interaction α decay have been reported. Because these variations have been presented by a number of groups, at various locations, using various types of detectors, different isotopes, and over extended periods of time, some researchers have interpreted the source of these variations as not from ambient environmental factors such as temperature, pressure, and humidity but via an unexplained fundamental interaction. The state of decay rate parameter variations experiments is reviewed, and the reported results are placed into a common comparable context by defining a phenomenological cross section. After that we make decay parameter measurements as a function of time at the level of 10 -5 in the presences of an antineutrino flux with an on-off cycle time of ≈ 30 days. This level of precision requires a detailed understanding of both systematic and statistical errors; otherwise, systematic errors in the measurement may mimic the decay events of fundamental interactions. The experiment searched for variation of the $^{54}_{25}$Mn, e - capture decay rate parameter and $^{137}_{55}$Cs, β - decay rate parameter both to a level of precision of 1 part in ≈10 5 by comparing the difference between the decay rate in the presence of an antineutrino flux ≈ 3 x 10 12 $\bar{ν}$ cm -2 s -1 and no flux measurements. The experiment was located 6.53 m from the reactor core of the High Flux Isotope Reactor at the Oak Ridge National Laboratory. Two weak interaction decays, one via electron capture and the other via β - decay, were selected because the final state and the time reverse state each contain a neutrino and antineutrino, covering arguments that the antineutrino flux may interact differently or not at all in one of the cases. The $\gamma$ spectra from both decays were collected and analyzed independently. The measured variation in the decay rate parameters are found to be δλ/λ =(0.034 ± 1.38) x10 -5 for $^{54}_{25}$Mn and δλ/λ =(0.67±1.56) x10 -5 for $^{137}_{55}$Cs. These results are consistent with no measurable decay rate parameter variation due to an antineutrino flux, yielding a 68% confidence level upper limit sensitivity for $^{54}_{25}$Mn δλ/λ ≤ 1.31 x 10 -5 or σ ≤ 1.29 x10 -25 cm 2 in cross section and for $^{137}_{55}$Cs δλ/λ ≤ 2.23 x 10 -5 or σ ≤ 5.69 x10 -27 cm 2 . The cross-section upper limit obtained in these null or no observable effect measurements are ≈ 10 4 times more sensitive than past experiments reporting positive results in 54 Mn and 137 Cs. . .

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1974

Procedures for experimental measurement and theoretical analysis of large plastic deformations

Theoretical equations are derived and analytical procedures are presented for the interpretation of experimental measurements of large plastic strains in the surface of a plate. Orthogonal gage lengths established on the metal surface are measured before and after deformation. The change in orthogonality after deformation is also measured. Equations yield the principal strains, deviatoric stresses in the absence of surface friction forces, true stresses if the stress normal to the surface is known, and the orientation angle between the deformed gage line and the principal stress-strain axes. Errors in the measurement of nominal strains greater than 3 percent are within engineering accuracy. Applications suggested for this strain measurement system include the large-strain-stress analysis of impact test models, burst tests of spherical or cylindrical pressure vessels, and to augment small-strain instrumentation tests where large strains are anticipated.

Morris, R. E.↗
NASA NTRS1981

Influence of velocity gradients on measurements of velocity and streamwise vorticity with hot-wire X-array probes

An analysis and measurement of the effects of the streamwise velocity gradients partial derivative of U with respect to y and partial derivative of U with respect to z, on the velocity components, U, v, and w, and the streamwise vorticity component, omega sub x measured in turbulent flow with a pair of orthogonal hot-wire X arrays, is presented. It is shown that these gradients, which can have the same order of magnitude instantaneously as the mean shear stress at the wall, cause extremely large errors in the measured instantaneous cross-stream velocity and streamwise vorticity components.

Vukoslavcevic, P.↗
NASA NTRS1983

The solar absolute spectral irradiance 1150-3173 A - May 17, 1982

The full-disk solar spectral irradiance in the spectral range 1150-3173 A was obtained from a rocket observation above White Sands Missile Range, NM, on May 17, 1982, half way in time between solar maximum and solar minimum. Comparison with measurements made during solar maximum in 1980 indicate a large decrease in the absolute solar irradiance at wavelengths below 1900 A to approximately solar minimum values. No change above 1900 A from solar maximum to this flight was observed to within the errors of the measurements. Irradiance values lower than the Broadfoot results in the 2100-2500 A spectral range are found, but excellent agreement with Broadfoot between 2500 and 3173 A is found. The absolute calibration of the instruments for this flight was accomplished at the National Bureau of Standards Synchrotron Radiation Facility which significantly improves calibration of solar measurements made in this spectral region.

Mount, G. H.↗
NASA NTRS1985

Land mobile satellite transmission measurements at 869 MHz. A comparison of error probabilities for various message block durations and fade margins as a function of vegetation shadowing

In order to give vehicles travelling in rural areas of the U.S. access to the telephone network, a Land Mobile Satellite System is being planned. Previously presented data by the author were analyzed for the probability that the received signal level dropped below a threshold during short time blocks of various signal durations and the conditional probability that such an event would reoccur after a given delay. If it assumed that a fade threshold crossing of even 1 msec would produce an error in the transmission, then the derived quantities can be considered error probabilities. Extensive tables and graphs are presented with the results from the analysis. They can be used to devise communication strategies which will provide improved link availability in the presence of vegetation shadowing.

Vogel, Wolfhard J.↗
NASA NTRS1990

Low-speed experiments - Requirements for stability measurements

The sources of error that may occur in low-speed stability and transition experiments due to sensitivity to environmental conditions are addressed. The format for the discussion is a problem statement followed by a solution. Global and local pressure gradients are considered, along with various distances from the disturbance source and impure disturbance input to the boundary layer. Three-dimensional distortion of the basic state is analyzed as well as freestream-disturbance, nonparallel, and smoke-wire effects. Crossflow roughness and probe and traverse interference are also covered.

Saric, William S.↗
NASA NTRS2003

Laboratory Characterization and Modeling of a Near-Infrared Enhanced Photomultiplier Tube

The photon-starved channel for optical communications from deep space requires the development of detector technology that can achieve photon-counting sensitivities with high bandwidth. In this article, a near-infrared enhanced photomultiplier tube (PMT) with a quantum e.ciency of 0.08 at a 1.06- m wavelength is characterized in the laboratory. A Polya distribution model is used to compute the probability distribution function of the emitted secondary photoelectrons from the PMT. The model is compared with measured pulse-height distributions with reasonable agreement. The model accounts for realistic device parameters, such as the individual dynode stage gains and a shape parameter that is representative of the spatial uniformity of response across the photocathode and dynodes. Bit-error rate (BER) measurements also are presented for 4- and 8-pulse-position modulation (PPM) modulation schemes with data rates of 20 to 30 Mb/s. A BER of 10-2 is obtained for a mean of 8 detected photons.

Biswas, A.↗
NASA NTRS1989

Ultrasonic pulsed phase locked loop interferometer for bolt load measurements

The pulsed phase-locked-loop bolt monitor (P2L2) that uses ultrasonic waves to measure bolt preload with accuracies ranging from 1 to 3 percent (depending on the specific bolt) is described. To remeasure bolt load after installation, a thermal calibration factor compensates for bolt temperature changes, and a standard reference block allows correction for acoustic phase errors due to measurement equipment configuration such as utilization of a different transducer, couplant, or cable. Some examples of critical applications including Space Shuttle landing-gear wheels and NASA wind-tunnel fan blades are discussed.

Allison, S. G.↗
NASA NTRSDate not supplied

Onboard Navigation Error Analysis for Aerocapture at Uranus

Capturing into an orbit around Uranus using aerocapture allows one to design a mission with faster interplanetary trajectories and less propellant requirements. Such an aerocapture mission would rely on the onboard Guidance, Navigation, and Control (GNC) subsystems to successfully capture into an orbit around Uranus. Uncertainty in the state information and the noise in the sensor measurements induce navigation errors in the guidance and control subsystems, which can affect the overall performance of the aerocapture mission at Uranus. Understanding the effect of these navigation errors on mission performance is essential. To this end, this work considers different sensors with varying quality to understand their impact on the overall mission performance. In addition, this paper studies the impact of the uncertainty in the initial states used to initialize the onboard navigation filter and understands their effect on mission performance. This paper also shows the onboard navigation errors obtained from the Linear Covariance (LinCov) analysis and uses them for verification and validation (V&V) of the results from Program to Optimize and Simulate Trajectories-II (POST2).

Pardha Sai Chadalavada↗
NASA NTRSDate not supplied

Onboard Navigation Error Analysis for Aerocapture at Uranus

Capturing into an orbit around Uranus using aerocapture allows one to design a mission with faster interplanetary trajectories and less propellant requirements. Such an aerocapture mission would rely on the onboard Guidance, Navigation, and Control (GNC) subsystems to successfully capture into an orbit around Uranus. Uncertainty in the state information and the noise in the sensor measurements induce navigation errors in the guidance and control subsystems, which can affect the overall performance of the aerocapture mission at Uranus. Understanding the effect of these navigation errors on mission performance is essential. To this end, this work considers different sensors with varying quality to understand their impact on the overall mission performance. In addition, this paper studies the impact of the uncertainty in the initial states used to initialize the onboard navigation filter and understands their effect on mission performance. This paper also shows the onboard navigation errors obtained from the Linear Covariance (LinCov) analysis and uses them for verification and validation (V\&V) of the results from Program to Optimize and Simulate Trajectories-II (POST2).

Aerocapture↗
NASA NTRS1991

Compensating sampling errors in stabilizing helmet-mounted displays using auxiliary acceleration measurements

A method based on complementary filtering is shown to be effective in compensating for the image stabilization error due to sampling delays of HMD position and orientation measurements. These delays would otherwise have prevented the stabilization of the image in HMDs. The method is also shown to improve the resolution of the head orientation measurement, particularly at low frequencies, thus providing smoother head control commands, which are essential for precise head pointing and teleoperation.

Merhav, S.↗