Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “linear response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Continued Development of Meandering Winding Magnetometer (MWM (Register Trademark)) Eddy Current Sensors for the Health Monitoring, Modeling and Damage Detection of Composite Overwrapped Pressure Vessels

Composite Overwrapped Pressure Vessels (COPVs) are used in essentially all NASA spacecraft, launch. vehicles and payloads to contain high-pressure fluids for propulsion, life support systems and science experiments. Failure of any COPV either in flight or during ground processing would result in catastrophic damage to the spacecraft or payload, and could lead to loss of life. Therefore, NASA continues to investigate new methods to non-destructively inspect (NDE) COPVs for structural anomalies and to provide a means for in-situ structural health monitoring (SHM) during operational service. Partnering with JENTEK Sensors, engineers at NASA, Kennedy Space Center have successfully conducted a proof-of-concept study to develop Meandering Winding Magnetometer (MWM) eddy current sensors designed to make direct measurements of the stresses of the internal layers of a carbon fiber composite wrapped COPV. During this study three different MWM sensors were tested at three orientations to demonstrate the ability of the technology to measure stresses at various fiber orientations and depths. These results showed good correlation with actual surface strain gage measurements. MWM-Array technology for scanning COPVs can reliably be used to image and detect mechanical damage. To validate this conclusion, several COPVs were scanned to obtain a baseline, and then each COPV was impacted at varying energy levels and then rescanned. The baseline subtracted images were used to demonstrate damage detection. These scans were performed with two different MWM-Arrays. with different geometries for near-surface and deeper penetration imaging at multiple frequencies and in multiple orientations of the linear MWM drive. This presentation will include a review of micromechanical models that relate measured sensor responses to composite material constituent properties, validated by the proof of concept study, as the basis for SHM and NDE data analysis as well as potential improvements including design changes to miniaturize and make the sensors durable in the vacuum of space

Russell, Richard↗
NASA NTRS2016

Modeling Relationships Between Flight Crew Demographics and Perceptions of Interval Management

The Interval Management Alternative Clearances (IMAC) human-in-the-loop simulation experiment was conducted to assess interval management system performance and participants' acceptability and workload while performing three interval management clearance types. Twenty-four subject pilots and eight subject controllers flew ten high-density arrival scenarios into Denver International Airport during two weeks of data collection. This analysis examined the possible relationships between subject pilot demographics on reported perceptions of interval management in IMAC. Multiple linear regression models were created with a new software tool to predict subject pilot questionnaire item responses from demographic information. General patterns were noted across models that may indicate flight crew demographics influence perceptions of interval management.

Remy, Benjamin↗
NASA NTRS2023

Dynamical Core Damping of Thermal Tides in Martian Atmosphere

Atmospheric oscillations with daily periodicity are observed in in-situ near-surface pressure, temperature, and winds observations, and also in remotely sensed temperature and pressure observations of the Martian atmosphere. Such oscillations are interpreted as thermal tides driven by the diurnal cycle of solar radiation and occur at various frequencies, with the most prominent being the diurnal, semidiurnal, terdiurnal and quadiurnal tides. Mars global circulation models reproduce these tides with varying levels of success. Until recently, both the MarsWRF and newly developed MarsMPAS models were able to produce realistic diurnal and semidiurnal tide amplitudes but predicted higher-order mode amplitudes that were significantly weaker than observed. We use linear wave analysis to show that the divergence damping applied within both MarsWRF and MarsMPAS is responsible for suppressing the amplitude of thermal tides with frequency greater than 2 per sol, despite being designed to suppress only acoustic wave modes. Decreasing the strength of the divergence damping in MarsWRF and MarsMPAS allows for excellent prediction of the higher order tidal modes. This finding demonstrates that care must be taken when applying numerical dampers and filters that may eliminate some desired dynamical features in planetary atmospheres.

Yuan Lian↗
NASA NTRSDate not supplied

On the Integration of Loudness Over Time for the Prediction of Single-Event Annoyance

Loudness is the quality of human perception that is most related to acoustic intensity and energy, however there is no agreed-upon way of integrating loudness over time for the prediction of noise-induced annoyance. Most noise metrics used today for aircraft certification and regulation employ the “Equal-Energy Hypothesis” (EEH) and sum the acoustical energy of one or more noise events over time to create a single metric value that represents the entire exposure. Using the EEH creates a natural tradeoff between the peak energy and the duration of a single noise event, the “hypothesis” being that this tradeoff optimally predicts annoyance in a wide variety of situations. This work proposes a strategy for integrating a loudness-like time series which is flexible in two ways: First, it includes a parameter b ∈ [0,1]. When b = 0, the metric will return the peak of the time series. At b = .5, the metric will behave in accordance with the EEH. At b = 1, the metric will penalize the duration of the sound more than the EEH would. Second, transformations are given so that the strategy can be computed from, or generate quantities in units analogous to, decibels (or phon), physical units (acoustic pressure/power), or perceptually-scaled units (sone). This approach is demonstrated on a dataset of annoyance responses to single events of UAV and road vehicle noise that is fit with an augmented linear regression. Analyses based on this integration of A-weighted level and the output of the “Zwicker” loudness model yield similar results: that subjects may have been slightly more sensitive to the durations of the events than the EEH would suppose, but that the EEH cannot be disproven using these data. The time-integrated metrics outperform both time-averaged and centile-based metrics.

Psychoacoustics↗
NASA NTRSDate not supplied

On the Integration of Loudness Over Time for the Prediction of Single-Event Annoyance

Loudness is the quality of human perception that is most related to acoustic intensity and energy, however there is no agreed-upon way of integrating loudness over time for the prediction of noise-induced annoyance. Most noise metrics used today for aircraft certification and regulation employ the “Equal-Energy Hypothesis” (EEH) and sum the acoustical energy of one or more noise events over time to create a single metric value that represents the entire exposure. Using the EEH creates a natural tradeoff between the peak energy and the duration of a single noise event, the “hypothesis” being that this tradeoff optimally predicts annoyance in a wide variety of situations. This work proposes a strategy for integrating a loudness-like time series which is flexible in two ways: First, it includes a parameter b ∈ [0,1]. When b = 0, the metric will return the peak of the time series. At b = .5, the metric will behave in accordance with the EEH. At b = 1, the metric will penalize the duration of the sound more than the EEH would. Second, transformations are given so that the strategy can be computed from, or generate quantities in units analogous to, decibels (or phon), physical units (acoustic pressure/power), or perceptually-scaled units (sone). This approach is demonstrated on a dataset of annoyance responses to single events of UAV and road vehicle noise that is fit with an augmented linear regression. Analyses based on this integration of A-weighted level and the output of the “Zwicker” loudness model yield similar results: that subjects may have been slightly more sensitive to the durations of the events than the EEH would suppose, but that the EEH cannot be disproven using these data. The time-integrated metrics outperform both time-averaged and centile-based metrics.

Psychoacoustics↗
NASA NTRS1998

Signal-Induced Noise Effects in a Photon Counting System for Stratospheric Ozone Measurement

Signal-induced noise (SIN) is a common effect resulting when a photomultiplier tube (PMT) is saturated, for a brief moment, with a high intensity light pulse. After the laser pulse is sent into the atmosphere a very large light return, from either the near-field or a cloud, causes the PMT to momentarily saturate. The PMT is gated off at this time so no signal is seen at the anode. When the PMT gate is turned on, the far-field light return from the atmosphere is observed. This signal is distorted, however because of the addition of SIN to the received light signal causing a slower than expected decay of the atmospheric signal return. We have characterized SIN responses to varying parameters of the incident light on the PMT. These varied parameters included incident wavelength, PMT voltage, incident intensity, and tube type. We found that only the amplitude of the SIN was effected by varying PMT voltages and light intensities. The amplitude increased linearly as input light intensity increased. Different incident wavelengths at the same intensity did not effect the amplitude or the temporal behavior of the SIN response. Finally, different PMT tubes with similar physical structures exhibited similar SIN responses although with different amplitudes. The different amplitudes can be attributed to the different gains and operating voltages of each tube. These results suggest that SIN is caused by photocathode electron dynamics such as charge accumulation on internal PMT surfaces. These surfaces then emit the electrons slowly resulting in a long decay noise signal. With the SIN responses characterized we can now try to develop a method to reduce or eliminate SIN in DIAL systems.

Harper, David B.↗
NASA NTRS1983

Mutagenic screening of diamine monomers

The effects of phenyl ring coupling moieties, of isomeric amine positions relative to the coupling groups, and of insertion of other coupling groups on the mutagenic response of a series of dianilines were investigated using the Ames Salmonella assay. Generally, S-9 metabolic activation from Aroclor-induced rat liver was required for mutagenic expression. The range of mutagenicity of steric isomers of several dianiline series was also investigated. No mutagenicity was found for purified samples of o,o' and m,p' isomers of methylene dianiline (MDA) and diaminobenzophenone, while varying degrees of mutagenicity were found for other isomers. The mutagenicity of "benzylogs" of MDA decreased as the degree of linear separation of the m,m' anilino groups by aromatic rings increased. Methylation and two-year storage increased mutagenic response in certain isomers of MDA. However, high performance liquid chromatography indicated there was no discernible change in m,p'-MDA samples aged under varied conditions over four months. Likewise, no change in mutagenicity was found.

Ross, W. D.↗
NASA NTRS1996

Design and Performance Improvements of the Prototype Open Core Flywheel Energy Storage System

A prototype magnetically suspended composite flywheel energy storage (FES) system is operating at the University of Maryland. This system, designed for spacecraft applications, incorporates recent advances in the technologies of composite materials, magnetic suspension, and permanent magnet brushless motor/generator. The current system is referred to as an Open Core Composite Flywheel (OCCF) energy storage system. This paper will present design improvements for enhanced and robust performance. Initially, when the OCCF prototype was spun above its first critical frequency of 4,500 RPM, the rotor movement would exceed the space available in the magnetic suspension gap and touchdown on the backup mechanical bearings would occur. On some occasions it was observed that, after touchdown, the rotor was unable to re-suspend as the speed decreased. Additionally, it was observed that the rotor would exhibit unstable oscillations when the control system was initially turned on. Our analysis suggested that the following problems existed: (1) The linear operating range of the magnetic bearings was limited due to electrical and magnetic saturation; (2) The inductance of the magnetic bearings was affecting the transient response of the system; (3) The flywheel was confined to a small movement because mechanical components could not be held to a tight tolerance; and (4) The location of the touchdown bearing magnifies the motion at the pole faces of the magnetic bearings when the linear range is crucial. In order to correct these problems an improved design of the flywheel energy storage system was undertaken. The magnetic bearings were re-designed to achieve a large linear operating range and to withstand load disturbances of at least 1 g. The external position transducers were replaced by a unique design which were resistant to magnetic field noise and allowed cancellation of the radial growth of the flywheel at high speeds. A central rod was utilized to ensure the concentricity of the magnetic bearings, the motor/generator, and the mechanical touchdown bearings. In addition, the mechanical touchdown bearings were placed at two ends of the magnetic bearing stack to restrict the motion at pole faces. A composite flywheel was made using a multi-ring interference assembled design for a high specific energy density. To achieve a higher speed and better efficiency, a permanent magnet DC brushless motor was specially designed and fabricated. A vacuum enclosure was constructed to eliminate windage losses for testing at high speeds. With the new improvements the OCCF system was tested to 20,000 RPM with a total stored energy of 15.9 WH and an angular momentum of 54.8 N-m-s (40.4 lb-ft-s). Motor current limitation, caused by power loss in the magnetic bearings, was identified as causing the limit in upper operating speed.

Pang, D.↗
NASA NTRS1978

Instrumental variables algorithm for modal parameter identification in flutter testing

The paper is concerned with the task of estimating modal parameters from system response measurement in aircraft flutter testing. A frequency-domain derivation of an instrumental-variables algorithm is presented for a linear time-invariant dynamic system of order n. Basically, this algorithm fits a set of poles and zeros to the measured transfer function. An illustrative example is provided regarding the application of the algorithm to aeroelasticity testing. It is shown that the algorithm can be implemented for on-line data reduction with a microcomputer-based analysis system. By using instrumental variables the sensitivity of the modal parameter estimates to noise in the system-response measurements is reduced greatly. The algorithm is expected to be a powerful and valuable tool for on-line estimation of modal parameters in flutter testing and should be useful in control system and structural dynamics tests.

Johnson, W.↗
NASA NTRS1992

An analysis of particle track effects on solid mammalian tissues

Relative biological effectiveness (RBE) and quality factor (Q) at extreme values of linear energy transfer (LET) have been determined on the basis of experiments with single-cell systems and specific tissue responses. In typical single-cell systems, each heavy particle (Ar or Fe) passes through a single cell or no cell. In experiments on animal tissues, however, each heavy particle passes through several cells, and the LET can exceed 200 keV micrometers-1 in every cell. In most laboratory animal tissue systems, however, only a small portion of the hit cells are capable of expressing the end-point being measured, such as cell killing, mutation or carcinogenesis. The following question was therefore addressed: do RBEs and Q factors derived from single-cell experiments properly account for the damage at high LET when multiple cells are hit by HZE tracks? A review is offered in which measured radiation effects and known tissue properties are combined to estimate on the one hand, the number of cells at risk, p3n, per track, where n is the number of cells per track based on tissue and organ geometry, and p3 is the probability that a cell in the track is capable of expressing the experimental end-point. On the other hand, the tissue and single-cell responses are compared by determining the ratio RBE in tissue/RBE in corresponding single cells. Experimental data from the literature indicate that tissue RBEs at very high LET (Fe and Ar ions) are higher than corresponding single-cell RBEs, especially in tissues in which p3n is high.

Non-NASA Center↗
NASA NTRS2002

Vestibular control of sympathetic activity. An otolith-sympathetic reflex in humans

It has been proposed that a vestibular reflex originating in the otolith organs and other body graviceptors modulates sympathetic activity during changes in posture with regard to gravity. To test this hypothesis, we selectively stimulated otolith and body graviceptors sinusoidally along different head axes in the coronal plane with off-vertical axis rotation (OVAR) and recorded sympathetic efferent activity in the peroneal nerve (muscle sympathetic nerve activity, MSNA), blood pressure, heart rate, and respiratory rate. All parameters were entrained during OVAR at the frequency of rotation, with MSNA increasing in nose-up positions during forward linear acceleration and decreasing when nose-down. MSNA was correlated closely with blood pressure when subjects were within +/-90 degrees of nose-down positions with a delay of 1.4 s, the normal latency of baroreflex-driven changes in MSNA. Thus, in the nose-down position, MSNA was probably driven by baroreflex afferents. In contrast, when subjects were within +/-45 degrees of the nose-up position, i.e., when positive linear acceleration was maximal along the naso-ocipital axis, MSNA was closely related to gravitational acceleration at a latency of 0.4 s. This delay is too short for MSNA changes to be mediated by the baroreflex, but it is compatible with the delay of a response originating in the vestibular system. We postulate that a vestibulosympathetic reflex, probably originating mainly in the otolith organs, contributes to blood pressure maintenance during forward linear acceleration. Because of its short latency, this reflex may be one of the earliest mechanisms to sustain blood pressure upon standing.

NASA Discipline Neuroscience↗
NASA NTRS2021

Canopy reflectance models illustrate varying NDVI responses to change in high latitude ecosystems

Multiyear trends in Normalized Difference Vegetation Index (NDVI) have been used as metrics of high latitude ecosystem change based on the assumption that NDVI change is associated with ecological change, generally as changes in green vegetation amount (green leaf area index [LAI] or plant cover). Further, no change in NDVI is often interpreted as no change in these variables. Three canopy reflectance models including linear mixture model, the SAIL (Scattering from Arbitrarily Inclined Leaves) model, and the GeoSail model were used to simulate scenarios representing high latitude landscape NDVI responses to changes in LAI and plant cover. The simulations showed inconsistent NDVI responses. Clear increases in NDVI are generally associated with increases in LAI and plant cover. At higher values of LAI, the change in NDVI per unit change in LAI decreases, with very little change in spruce forest NDVI where crown cover is >50% and at the tundra–taiga ecotone with transitions from shrub tundra to spruce woodland. These lower responses may bias the interpretation of greening/browning trends in boreal forests. Variations in water or snow coverage were shown to produce outsized nonbiological NDVI responses. Inconsistencies in NDVI responses exemplify the need for care in the interpretation of NDVI change as a metric of high latitude ecosystem change, and that landscape characteristics in terms of the type of cover and its characteristics, such as the initial plant cover, must be taken into account in evaluating the significance of any observed NDVI trends.

Karl F Huemmrich↗
NASA NTRS1990

Effect of shaping sensor data on pilot response

The pilot of a modern jet aircraft is subjected to varying workloads while being responsible for multiple, ongoing tasks. The ability to associate the pilot's responses with the task/situation, by modifying the way information is presented relative to the task, could provide a means of reducing workload. To examine the feasibility of this concept, a real time simulation study was undertaken to determine whether preprocessing of sensor data would affect pilot response. Results indicated that preprocessing could be an effective way to tailor the pilot's response to displayed data. The effects of three transformations or shaping functions were evaluated with respect to the pilot's ability to predict and detect out-of-tolerance conditions while monitoring an electronic engine display. Two nonlinear transformations, on being the inverse of the other, were compared to a linear transformation. Results indicate that a nonlinear transformation that increases the rate-or-change of output relative to input tends to advance the prediction response and improve the detection response, while a nonlinear transformation that decreases the rate-of-change of output relative to input tends to lengthen the prediction response and make detection more difficult.

Bailey, Roger M.↗
NASA NTRS1995

Issues in protection from galactic cosmic rays

Radiation risks to astronauts depend on the microscopic fluctuations of energy absorption events in specific tissues. These fluctuations depend not only on the space environment but also on the modifications of that environment by the shielding provided by structures surrounding the astronauts and the attenuation characteristics of the astronaut's body. The effects of attenuation within the shield and body depends on the tissue biological response to these microscopic fluctuations. In the absence of an accepted method for estimating astronaut risk, we examined the attenuation characteristics using conventional linear energy transfer (LET)-dependent quality factors (as one means of representing relative biological effectiveness, RBE) and a track-structure repair model to fit cell transformation (and inactivation) data in the C3H10 T1/2 mouse cell system obtained for various ion beams. Although the usual aluminum spacecraft shield is effective in reducing dose equivalent with increasing shield thickness, cell transformation rates are increased for thin aluminum shields. Clearly, the exact nature of the biological response to LET and track width is critical to evaluation of biological protection factors provided by a shield design. A significant fraction of biological injury results from the LET region above 100 keV/mu m. Uncertainty in nuclear cross-sections results in a factor of 2-3 in the transmitted LET spectrum beyond depths of 15 g/cm2, but even greater uncertainty is due to the combined effects of uncertainty in biological response and nuclear parameters. Clearly, these uncertainties must be reduced before the shield design can be finalised.

NASA Discipline Number 45-10↗
NASA NTRS2006

Upwelling of Arctic pycnocline associated with shear motion of sea ice

High-resolution radar imagery shows that the dynamic response of winter sea ice to gradients in large-scale surface wind stress is often localized along quasi-linear fractures hundreds of kilometers long. Relative shearing motion across these narrow fractures can exceed 10 cm/s. In one event recorded during the drift of the SHEBA ice camp, we observed an intense zone of pycnocline upwelling (approx.14 m) associated with significant shear motion near the camp, while upward turbulent heat flux in the ocean boundary layer reached nearly 400 W/sq m, an order of magnitude greater than at any other time during the year-long drift. We attribute the upwelling to Ekman pumping associated with concentrated ice shear. Over the entire Arctic Ocean sea ice cover, this process could be responsible for significant heat exchange between the cold surface layer and warmer subsurface water at the ubiquitous fractures resulting from large-scale atmosphere-ice interactions.

McPhee, M. G.↗
NASA NTRS1971

Analysis of transient, linear wave propagation in shells by the finite difference method

The applicability of the finite difference method to propagation problems in shells, and the response of a cylindrical shell with cutouts to both longitudinal and radial transient excitations are investigated. It is found that the only inherent limitation of the finite difference method is its inability to reproduce accurately response discontinuities. The short wave length limitations of thin shell theory create significant convergence difficulties may often be overcome through proper selection of finite difference mesh dimensions and temporal or spatial smoothing of the excitation. Cutouts produce moderate changes in early and intermediate time response of a cylindrical shell to axisymmetric pulse loads applied at one end. The cutouts may facilitate the undesirable late-time transfer of load-injected extensional energy into nonaxisymmetric flexural response.

Geers, T. L.↗