SEARCH · Engineering Papers

Results for “graphite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Design detail verification tests for a lightly loaded open-corrugation graphite-epoxy cylinder

Flat corrugated graphite-epoxy panels were tested in compression to verify selected design details of a ring-stiffened cylinder that was designed to support an axial compressive load of 157.6 kN/m without buckling. Three different sizes of subcomponent panels, with the same basic corrugation geometry, were tested: (1) 60.96-cm-long by 45.72-cm-wide panels to evaluate the local buckling strength of the shell wall design; (2) 91.44-cm-long by 45.72-cm-wide panels to evaluate a longitudinal joint and the load-introduction method; and (3) 254.0-cm-long by 91.44-cm-wide panels with four simulated-ring stiffeners to evaluate the ring-attachment method. The test results indicate that the modified shell-wall design, the longitudinal joint, the load-introduction method, and the stiffener-attachment method for the proposed cylinder have adequate strength to support the design load.

Davis, R. C.↗

NASA NTRS1982

Buckling test of a 3-meter-diameter corrugated graphite-epoxy ring-stiffened cylinder

A three m diameter by three m long corrugated cylindrical shell with external stiffening rings was tested to failure by buckling. The corrugation geometry for the graphite epoxy composite cylinder wall was optimized to withstand a compressive load producing an ultimate load intensity of 157.6 kN/m without buckling. The test method used to produce the design load intensity was to mount the specimen as a cantilevered cylinder and apply a pure bending moment to the end. A load introduction problem with the specimen was solved by using the BOSOR 4 shell of revolution computer code to analyze the shell and attached loading fixtures. The cylinder test loading achieved was 101 percent of design ultimate, and the resulting mass per unit of shell wall area was 1.96 kg/sq m.

Davis, R. C.↗

NASA NTRS1982

Space environmental effects: Construction and utilization of a system to measure low thermal strain in one meter graphite epoxy tubes

A system for measuring the expansion of low coefficient of thermal expansion (CTE) materials was constructed around a H.P. 5526-A laser measuring system. The vacuum CTE measurements in the -150 F to +120 F range were made over a 6 month period on a graphite epoxy tube yielding CTE values of 2.5 to one fifty-millionth/F above ambient and 2 + or - one ten-millionth F below ambient temperature. To assure that the below ambient, approximately 10 microns high open loop nature of the delta L/L vs. T curves was not apparatus related, similar size quartz tubes (A and B) were checked and found to have only a 2 micron (negligable for quartz) open loop component. These two quartz tubes, A and B, had ambient CTE values 20% and 45% respectively higher than the average handbook value. The overnight microcreep diminished an order of magnitude during the first several cycles after the system had been reopened.

Davis, J. H.↗

NASA NTRS1982

The properties of novel bisimide amine cured epoxy/Celion 6000 graphite fiber composites

The study is concerned with the further development of bisimide amine cured epoxy resins first reported by Serafini et al. (1979). Attention is given to properties of the neat resins and composites made with these novel epoxy resins and Celion 6000 graphite fibers. The use of bisimide amine hardeners to cure epoxy resins causes a significant improvement in the char-forming characteristics of the cured resin. Compared to epoxy resins cured with a conventional amine, such as 4,4'-diaminodiphenylsulfone, the bisimide cured epoxies exhibit about a twofold improvement in the aerobic char yield at 800 C. The levels of moisture absorption exhibited by the bisimide amine cured epoxies were found to be considerably lower than those exhibited by state-of-the-art epoxies (0.5 wt.% versus 2.0%).

Scola, D. A.↗

NASA NTRS1981

Effect of load, area of contact, and contact stress on the tribological properties of polyimide bonded graphite fluoride films

A pin-on-disk type of friction and wear apparatus was used to study the effect of load, contact stress and rider area of contact on the friction and wear properties of polyimide-bonded graphite fluoride films. Different rider area contacts were obtained by initially generating flats (with areas of 0.0035, 0.0071, 0.0145, and 0.0240 cm) on 0.476-cm radius hemispherically-tipped riders. Different projected contact stresses were obtained by applying loads of 2.5-to 58.8-N to the flats. Two film wear mechanisms were observed. The first was found to be a linear function of contact stress and was independent of rider area of contact. The second was found to increase exponentially as the stress increased. The second also appeared to be a function of rider contact area. Wear equations for each mechanism were empirically derived from the experimental data. In general, friction coefficients increased with increasing rider contact area and with sliding duration. This was related to the build-up of thick rider transfer films.

Fusaro, R. L.↗

NASA NTRS1982

Effect of orthotropic properties and panel width on the compression strength of graphite-epoxy laminates with holes

An experimental study conducted to evaluate the effect of laminate orthotropic properties and panel width on the compression strength of 48-ply graphite-epoxy laminates with drilled holes is described. The test results are evaluated on the basis of hole size and specimen width and are used in determining parameters necessary for predicting trends using the point stress failure criterion. Good agreement is obtained between experimental and predicted values of failure for panels fabricated from two quasi-isotropic laminates and one orthotropic laminate. The results suggest that panels of different widths having holes that are large in relation to the failure prediction parameter should be included in any test program conducted to develop prediction trends that may be used in design applications.

Rhodes, M. D.↗

NASA NTRS1982

Postbuckling behavior of selected flat stiffened graphite-epoxy panels loaded in compression

Results of an experimental study of the postbuckling behavior of selected flat stiffened graphite-epoxy panels loaded in compression are presented. The postbuckling response and failure characteristics of undamaged panels and panels damaged by low-speed impact are described. Each panel had four equally-spaced I-spaced stiffeners and 16- or 24-ply quasi-isotropic skins. Panels with three different stiffener spacings were tested. Some undamaged specimens supported as much as three times their initial buckling load before failing. Failure of all panels initiated in a skin-stiffener interface region. Analytical results obtained from a nonlinear general shell finite element analysis computer code correlate well with typical postbuckling test results up to failure. The analytical modeling detail necessary to predict accurately the response of a panel is described. Test results show that low-speed impact damage can reduce the postbuckling strength of a stiffened panel and that the skin-stiffener interface region is more sensitive to impact damage than the skin midway between stiffeners.

Starnes, J. H., Jr.↗

NASA NTRS1982

Carbon in the Allende meteorite - Evidence for poorly graphitized carbon rather than carbyne

A carbon-rich acid residue from the Allende carbonaceous chondrite was examined by high-resolution transmission electron microscopy (HRTEM) and also by analytical electron microscopy. A TEM mount of this residue that has previously been reported to contain carbyne forms of carbon was shown to contain sheet silicate contaminants. These sheet silicate grains give electron diffraction patterns similar to those reported for carbynes, thus raising questions about the previous report of carbynes in this residue. Furthermore, two crystals from a glacier microspherule, which had previously been identified as carbyne VIII, were shown by microanalysis to be talc. In view of these observations it is suggested that identifications of carbyne by electron diffraction should be supported by microanalyses of the individual grains. HRTEM investigations of the Allende carbon indicate that it is a poorly crystalline graphite, structurally similar to 'glassy' carbon

Smith, P. P. K.↗

NASA NTRS1982

Predictions for partial and monolayer coverages of O2 on graphite

Monolayer properties of O2 on graphite are calculated using a pattern recognition, optimization scheme. Equilibrium monolayers are predicted at two different densities with properties in agreement with recent X-ray diffraction, specific heat, and neutron scattering data. Properties of the extremely low density regime are calculated using a model based upon a distribution of two-dimensional O2 clusters. The results are consistent with experimental evidence.

Pan, R. P.↗

NASA NTRS1982

Ion sputter textured graphite

A specially textured surface of pyrolytic graphite exhibits extremely low yields of secondary electrons and reduced numbers of reflected primary electrons after impingement of high energy primary electrons. An ion flux having an energy between 500 eV and 1000 eV and a current density between 1.0 mA/sq cm and 6.0 mA/sq cm produces surface roughening or texturing which is in the form of needles or spines. Such textured surfaces are especially useful as anode collector plates in high efficiency electron tube devices.

Sovey, J. S.↗

NASA NTRS1982

Failure characteristics of graphite-epoxy structural components loaded in compression

Failure characteristics of compressively loaded graphite-epoxy components are described. Experimental results for both strength-critical laminates and structural components with postbuckling strength are presented. Effects of low speed impact damage and circular holes on compressive strength are discussed. Delamination and shear crippling failure mechanisms that limit the performance of strength-critical laminates are described. Transverse shear and skin-stiffener separation failure mechanisms that limit the performance of components with postbuckling strength are also described. The influence of matrix properties on compressive strength improvements for impact damaged laminates is discussed. Experimental data and results from a failure analysis for strength-critical laminates with cutouts are discussed and compared with impact damage results. Typical postbuckling test results are compared with analytical predictions.

Starnes, J. H., Jr.↗

NASA NTRS1982

Development of a Priest interferometer for measurement of the thermal expansion of a graphite epoxy in the temperature range 116-366 K

The thermal expansion behavior of graphite epoxy laminates between 116 and 366 degrees Kelvin was investigated using as implementation of the Priest interferometer concept. The design, construction and use of the interferometer along with the experimental results it was used to generate are described. The experimental program consisted of 25 tests on 25.4 mm and 6.35 mm wide, 8 ply pi/4 quasi-isotropic T300-5208 graphite/epoxy specimens and 3 tests on a 25.4 mm wide unidirectional specimen. Experimental results are presented for all tests along with a discussion of the interferometer's limitations and some possible improvements in its design.

Short, J. S.↗

NASA NTRS1983

Buckling and failure characteristics of graphite-polyimide shear panels

The buckling and failure characteristics of unstiffened, blade stiffened, and hat stiffened graphite-polyimide shear panels are described. The picture frame shear test is used to obtain shear stress-strain data at room temperature and at 316 deg C. The experimental results are compared with a linear buckling analysis, and the specimen failure modes are described. The effect of the 316 deg C test temperature on panel behavior are discussed.

Shuart, M. J.↗

NASA NTRS1981

Graphite polystyryl pyridine (PSP) structural composites

PSP6022 M resin, PSP 6024 M resin and W 133 Thormel T 300 graphite fabric reinforced panels were fabricated and provided to NASA Ames Research Center. PSP6022 and PSP6024 characteristics, process specifications for the fabriation of prepregs and of laminates are detailed. Mechanical properties, thermomechanical properties and moisture resistance were evaluated. PSP6022 and PSP6024 appear as high performance thermostable systems, very easy to process, being soluble in MEK for prepregging and being cured at no more than 250C, and even 200C.

Malassine, B.↗

NASA NTRS1982

Mixed polyvalent-monovalent metal coating for carbon-graphite fibers

An improved coating of gasification catalyst for carbon-graphite fibers is provided comprising a mixture of a polyvalent metal such as calcium and a monovalent metal such as lithium. The addition of lithium provides a lighter coating and a more flexible coating when applied to a coating of a carboxyl containing resin such as polyacrylic acid since it reduces the crosslink density. Furthermore, the presence of lithium provides a glass-like substance during combustion which holds the fiber together resulting in slow, even combustion with much reduced evolution of conductive fragments. The coated fibers are utilized as fiber reinforcement for composites.

Harper-Tervet, J.↗

NASA NTRS1982

Electrochemical intercalation and electrical conductivity of graphite fibers

Lamellar compounds of graphite fibers were prepared by electrochemical intercalation. The dependence of the electrical resistance on the intercalate concentration was determined by a quasi simultaneous method. A factor 30 decrease of the relative fiber resistance was obtained with fluorosulfuric acid.

Besenhard, J. O.↗

NASA NTRS1983

Characteristics of thermally-induced transverse cracks in graphite epoxy composite laminates

The characteristics of thermally induced transverse cracks in T300/5208 graphite-epoxy cross-ply and quasi-isotropic laminates were investigated both experimentally and analytically. The formation of transverse cracks and the subsequent crack spacing present during cool down to -250 F (116K) and thermal cycling between 250 and -250 F (116 and 394K) was investigated. The state of stress in the vicinity of a transverse crack and the influence of transverse cracking on the laminate coefficient of thermal expansion (CTE) was predicted using a generalized plane strain finite element analysis and a modified shear lag analysis. A majority of the cross-ply laminates experienced transverse cracking during the initial cool down to -250 F whereas the quasi-isotropic laminates remained uncracked. The in situ transverse strength of the 90 degree layers was more than 1.9 times greater than the transverse strength of the unidirectional 90 degree material for all laminates investigated.

Adams, D. S.↗

NASA NTRS1982

Material characterization and specification development for 350 F curing epoxy-graphite materials

New analytical techniques and a processability laminate have been used in the development of a material specification for 350 F curing epoxy-graphite materials. The development of the specification required the evaluation of prepregs which had variations in their processing behavior that were detected only in production. Chemical techniques were used to analyze the prepregs and establish limits on the concentrations of the various chemical constituents. A batch acceptance test laminate was designed to determine suitability of prepregs for production useage. The new specification requires that the processability laminate be ultrasonically and micrographically inspected for voids and porosity. Incorporation of these and other requirements will help to insure material consistency and processability.

Rogers, A. K.↗