SEARCH · Engineering Papers

Results for “frequency range”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Application of system identification to analytic rotor modeling from simulated and wind tunnel dynamic test data, part 2

An introduction to aircraft state and parameter identification methods is presented. A simplified form of the maximum likelihood method is selected to extract analytical aeroelastic rotor models from simulated and dynamic wind tunnel test results for accelerated cyclic pitch stirring excitation. The dynamic inflow characteristics for forward flight conditions from the blade flapping responses without direct inflow measurements were examined. The rotor blades are essentially rigid for inplane bending and for torsion within the frequency range of study, but flexible in out-of-plane bending. Reverse flow effects are considered for high rotor advance ratios. Two inflow models are studied; the first is based on an equivalent blade Lock number, the second is based on a time delayed momentum inflow. In addition to the inflow parameters, basic rotor parameters like the blade natural frequency and the actual blade Lock number are identified together with measurement bias values. The effect of the theoretical dynamic inflow on the rotor eigenvalues is evaluated.

Hohenemser, K. H.↗

NASA NTRS1980

Calculated and measured performance of a 'near ideal' locally reacting duct liner in grazing incidence

The calculated acoustic response of a nearly ideal (locally reacting and linear) duct liner has been compared with its measured performance. The ceramic honeycomb liner structure was such that the local reaction assumption was well satisfied over the frequency range of interest (0.5-3.0 kHz). In addition, the high repeatability of the measured impedance values over a large SPL range verified the assumption of linearity. A finite element algorithm was used to compute the duct liner transmission properties in terms of the liner's normal incidence impedance and the duct termination impedance using a plane wave source. Very good agreement between theory and experiment was observed in general, but required accurate normal impedance values in the high attenuation frequency bands of the liner's response.

Parrott, T. L.↗

NASA NTRS1989

Airfoil profile drag increase due to acoustic excitation

A two-dimensional airfoil (NACA-0009) is subjected to high intensity pure-tone sound over a 1-5 kHz frequency range while immersed in a flow with 240 ft/sec velocity in a quiet flow facility with a Reynolds number of 3 million. Wake dynamic pressures are determined, and the momentum deficit is used to calculate a two-dimensional drag coefficient. Significant increases in drag are observed when the airfoil is subjected to high-intensity sound at critical frequencies. The increased drag is accompanied by movement of the natural transition location. When the transition is fixed by roughness at 10 percent chord, no further transition movement is observed in response to an acoustic Tollmien-Schlichting disturbance. However, a 4 percent increase in the sectional drag coefficient is noted. It is believed to be due to the sound exciting the flow near the airfoil surface (shear layer), thus causing the existing turbulence to become more intense, possess a higher mixing rate (momentum), and increase the skin friction.

Shearin, John G.↗

DOE OSTI2026

Non-Markovian relaxation spectroscopy of fluxonium qubits

Recent studies have shown that parasitic two-level systems (TLS) in superconducting qubits, which are a leading source of decoherence, can have relaxation times longer than the qubits themselves. However, the standard techniques used to characterize qubit relaxation is only valid for measuring T 1 under the Born-Markov approximation and could mask environmental memory effects in practice. Here, we introduce two-timescale relaxometry, a technique to probe the qubit and environment relaxation simultaneously and efficiently. We apply it to high-coherence fluxonium qubits over a frequency range of 0.1-0.4 GHz, and reveal a discrete spectrum of TLS with millisecond lifetimes. Our analysis of the spectrum is consistent with a random distribution of TLS in the aluminum oxide tunnel barrier of the Josephson junction chain of the fluxonium, with a spectral and volumetric density and average electric dipole similar to previous TLS studies at much higher frequencies. Our study suggests that investigating and mitigating TLS in the junction chain is crucial to the development of various types of noise-protected qubits in circuit QED.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2016

An AC modulated near infrared gain calibration system for a “Violin-Mode” transimpedance amplifier, intended for advanced LIGO suspensions

The background to this work was a prototype shadow sensor, which was designed for retro-fitting to an advanced LIGO (Laser Interferometer Gravitational wave Observatory) test-mass/mirror suspension, in which a 40 kg test-mass/mirror is suspended by four approximately 600 mm long by 0.4 mm diameter fused-silica suspension fibres. The shadow sensor comprised a LED source of Near InfraRed (NIR) radiation, and a “tall-thin” rectangular silicon photodiode detector, which together were to bracket the fibre under test. The photodiode was positioned so as to be sensitive (primarily) to transverse “Violin-Mode” vibrations of such a fibre, via the oscillatory movement of the shadow cast by the fibre, as this moved across the face of the detector. In this prototype shadow sensing system the photodiode was interfaced to a purpose-built transimpedance amplifier, this having both AC and DC outputs. A quasi-static calibration was made of the sensor’s DC responsivity, i.e., incremental rate of change of output voltage versus fibre position, by slowly scanning a fused-silica fibre sample transversely through the illuminating beam. The work reported here concerns the determination of the sensor’s more important AC (Violin-Mode) responsivity. Recognition of the correspondence between direct AC modulation of the source, and actual Violin-Mode signals, and of the transformative role of the AC/DC gain ratio for the amplifier, at any modulation frequency, f, resulted in the construction of the AC/DC calibration source described here. A method for determining in practice the transimpedance AC/DC gain ratio of the photodiode and amplifier, using this source, is illustrated by a specific numerical example, and the gain ratio for the prototype sensing system is reported over the frequency range 1 Hz–300 kHz. In fact, a maximum DC responsivity of 1.26 kV.m{sup −1} was measured using the prototype photodiode sensor and amplifier discussed here. Therefore, the measured AC/DC transimpedance gain ratio of 922.5 for this sensor, at 500 Hz, translated into a maximum Violin-Mode (AC) responsivity of (1.16 ± 0.05) MV m{sup −1}, at that frequency.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

NASA NTRS1987

Microwave dielectric behavior of vegetation material

The microwave dielectric behavior of vegetation was examined through the development of theoretical models involving dielectric dispersion by both bound and free water and supported by extensive dielectric measurements conducted over a wide range of conditions. The experimental data were acquired using an open-ended coaxial probe that was developed for sensing the dielectric constant of thin layers of materials, such as leaves, from measurements of the complex reflection coefficient using a network analyzer. The probe system was successfully used to record the spectral variation of the dielectric constant over a wide frequency range extending from 0.5 to 20.4 GHz at numerous temperatures between -40 to +40 C. The vegetation samples were measured over a wide range of moisture conditions. To model the dielectric spectrum of the bound water component of the water included in vegetation, dielectric measurements were made for several sucrose-water solutions as analogs for the situation in vegetation. The results were used in conjunction with the experimental data for leaves to determine some of the constant coefficients in the theoretical models. Two models, both of which provide good fit to the data, are proposed.

Elrayes, Mohamed A.↗

NASA NTRS2019

Audibility of Multiple, Low-Frequency Tonal Signals in Noise

The main purpose of this study is to examine the audibility of multiple, low-frequency tones that are placed in distinct auditory channels. Three experiments are described, the goals of which are to determine if the presence of sound in multiple channels results in enhanced audibility and to assess the applicability of the Statistical Summation Model (SSM) to this frequency range. This model predicts that for the case of multiple signals that are in separate auditory channels, implying statistical independence, each with sensitivity value d prime of i, the resulting total sensitivity is given by the square root of the sum of the squares of the individual d prime of i values. In common with previous studies conducted at higher frequencies, the signals are pure tones and the maskers are broadband noise. The requirement that low frequency tones be placed in separate auditory filters limited the number of tones to a maximum of three. The first of the three experiments measured the change in masked thresholds for two- and three-tone signals relative to the level of the equally-detectable single tones. The multiple tone signals were composed of combinations of 55, 120 and 200 Hz tones. The measured changes in thresholds exceeded those predicted by the SSM, although they did not differ statistically from the model predictions. The second experiment employed the same overall approach but acquired more data and concentrated on the three-tone signal. Once again, the measured changes in masked threshold exceeded the model predictions, this time to a statistically-significant degree. Two issues were postulated with the potential to yield inflated changes in masked threshold: interaction between tones resulting in perceptible intermodulation/difference tones, and the assumption that the tones were in distinct auditory filters and statistically independent of one another. The third experiment used two sets of three-tone signals to address these latter concerns. The first set of three tones was composed of harmonically related tone frequencies of 55, 110 and 165 Hz, which was an attempt to reduce effects of intermodulation difference tones. The second set of three tones was chosen to be 110, 220 and 330 Hz, again reducing effects of difference tones, but also providing greater separation between tones. Results for the first set of three tones compared to those of the earlier experiments indicated that intermodulation was not an important effect. The second set of three tones (110, 220, 330 Hz) yielded changes in masked thresholds that, on average, were in good agreement with the SSM, although intersubject variability was large and prohibited a definitive conclusion regarding the concern that tone spacing was inadequate. The results of the three experiments showed that the masked threshold of sounds with multiple (two or three) equally-detectable low frequency tones was lower than those of the single tones. In other words, it is clear that audibility is enhanced by the presence of signals in multiple auditory filters. This finding is consistent with most previous research conducted at higher frequencies. In contrast with previous research, test subjects were, on average, able to detect multitone sounds at lower levels than those predicted using the SSM. Analyses that included Monte Carlo simulations showed that normally distributed errors in the single tone thresholds result in biased estimates of the thresholds of multitone sounds. This phenomenon is likely responsible for at least a substantial fraction of the unexpected deviation of measurements from SSM predictions.

Rafaelof, Menachem↗

NASA NTRS1961

A Study of Longitudinal Control Problems at Low and Negative Damping and Stability with Emphasis on Effects of Motion Cues

As part of a general investigation to determine the effects of simulator motions on pilot opinion and task performance over a wide range of vehicle longitudinal dynamics, a cooperative NASA-AMAL program was conducted on the centrifuge at Johnsville, Pennsylvania. The test parameters and measurements for this program duplicated those of earlier studies made at Ames Research Center with a variable-stability airplane and with a pitch-roll chair flight simulator. Particular emphasis was placed on the minimum basic damping and stability the pilots would accept and on the minimum dynamics they considered controllable in the event of stability-augmentation system failure. Results of the centrifuge-simulator program indicated that small positive damping was required by the pilots over most of the frequency range covered for configurations rated acceptable for emergency conditions only (e.g., failure of a pitch damper). It was shown that the pilot's tolerance for unstable dynamics was dependent primarily on the value of damping. For configurations rated acceptable for emergency operation only, the allowable instability and damping corresponded to a divergence time to double amplitude of about 1 second. Comparisons were made of centrifuge, pitch-chair and fixed-cockpit simulator tests with flight tests. Pilot ratings indicated that the effects of incomplete or spurious motion cues provided by these three modes of simulation were important only for high-frequency, lightly damped dynamics or unstable, moderately damped dynamics. The pitch- chair simulation, which provided accurate angular-acceleration cues to the pilot, compared most favorably with flight. For the centrifuge simulation, which furnished accurate normal accelerations but spurious pitching and longitudinal accelerations, there was a deterioration of pilots' opinion relative to flight results. Results of simulator studies with an analog pilot replacing the human pilot illustrated the adaptive capability of human pilots in coping with the wide range of vehicle dynamics and the control problems covered in this study. It was shown that pilot-response characteristics, deduced by the analog-pilot method, could be related to pilot opinion. Possible application of these results for predicting flight-control problems was illustrated by means of an example control-problem analysis. The results of a brief evaluation of a pencil-type side-arm controller in the centrifuge showed a considerable improvement in the pilots' ability to cope with high-frequency, low-damping dynamics, compared to results obtained with the center stick. This improvement with the pencil controller was attributed primarily to a marked reduction in the adverse effects of large and exaggerated pitching and longitudinal accelerations on pilot control precision.

Sadoff, Melvin↗

NASA NTRS1982

Radar scatterometry of sand dunes and lava flows

Four frequency like polarized scatterometer data over a sand dune field and a volcanic field were analyzed to understand the scattering characteristics of these two terrain types as a function of frequency and incidence angle. For the frequency range studied (400 MHz to 13.3 GHz) unvegetated sand dunes are specular reflectors that return an echo to the radar antenna particularly when the geometry is such that the dune slope is nearly perpendicular to the antenna. Vegetation on the dunes can cause significant backscatter. Lava flows are strong diffuse scatterers which have backscatter values similar to coniferous forest at certain frequencies. Different observation frequencies are required for different situations. The scatterometer data correlate well with radar images.

Blom, R.↗

DOE OSTI2025

Multi-modal effects on indirect noise induced by turbulent entropy fields

Planar entropy waves are commonly assumed for predicting indirect combustion noise. However, the non-planar and turbulent nature of flows found in most practical combustors challenges this assumption. In the present paper, we examine the indirect noise generated by non-planar and turbulent entropy fields through subsonic nozzles. Firstly, we introduce a new transfer function framework that accounts for the contribution of non-planar Fourier modes of the entropy field to the indirect noise spectra. When applied to a turbulent flow field, this method demonstrates a significant improvement in spectral predictions compared with a conventional approach that only considers the planar mode. Secondly, simulations show that non-planar Fourier modes become significant above a threshold frequency ƒ thresh , found in the mid- to high-frequency range. This contribution of non-planar modes is explained by two-dimensional shear effects that distort the entropy waves. A scaling relation that uses residence times along streamlines is developed for ƒ thresh , showing good agreement with simulation results. Finally, we show that the indirect noise from non-planar entropy modes found in aviation combustors can be significant at frequencies below 1 kHz, which might be relevant in situations of thermo-acoustic instabilities coupled to indirect noise.

42 ENGINEERING↗

NASA NTRS1980

Turbulence suppression in free shear flows by controlled excitation

The mechanism of turbulence suppression in the near field of a free shear flow under controlled acoustic excitation is investigated. The near fields of four circular air jets, a plane air jet and a large single-stream plane free air mixing layer with laminar efflux boundary layers were monitored with hot-wire anemometers. The suppression effect is found to occur over the entire frequency range in all the flows studied, with maximal suppression (as much as 80%) at about 400 initial shear layer momentum thicknesses downstream from the exit and for excitation at a Strouhal number of 0.017. Suppression is shown to be a consequence of excitation-induced modification of the shear layer instability mode and the resulting structure, and to occur at the excitation frequency corresponding to the maximally unstable disturbance frequency of the initial free shear layer. Flow visualization reveals the presence of strong, large-scale vortical structures in the unexcited flow, which are weakened and diminished by excitation. It is concluded that excitation produces rapid roll-up and early breakdown of the shear layer, thus inhibiting the formation of energetic large-scale vortices and reducing the large fluctuation intensities caused by the passage and interaction of these vortices.

Zaman, K. B. M. Q.↗

NASA NTRS1983

C-band measurements of radar backscatter from ice project summary report

The ability to measure the radar scattering coefficient of ice with a helicopter or surface spectrometer was extended into the 4-8 GHz spectral region. The scattering coefficient was measured at Mould Bay, N.W.T., over a frequency range from 4 to 18 GHz for both summer and fall conditions. Scatter from fresh water ice in the St. Lawrence River and from numerous seasonal sea-ice types along the coast of Newfoundland were also measured. The C-band (near 5 GHz) scattering cross section for different types of ice shows poorer contrast than the scattering coefficient at higher frequencies, but better contrast than the negligible value found at L-band (1.5 GHz). At frequencies above 4 GHz the contrast in scattering coefficient between the different ice types is much less in summer than in other seasons; at most times of year the scattering is much stronger from multiyear than from other ice types, but in early summer it is actually slightly weaker than that from first year ice.

Onstott, R. G.↗

NASA NTRS1992

Onset of dispersion in Nb microstrip transmission lines at submillimeter wave frequencies

We have measured the dispersion in phase velocity of a Nb-SiO(x)-Nb microstrip transmission line resonator over a frequency range from 50 GHz to 800 GHz. A submicron Nb/Al-AlO(x)/Nb Josephson junction was used as a voltage-controlled oscillator to excite the high order modes in the resonator. The same junction is used as a direct detector resulting in a series of step-like structures in the DC current-voltage characteristic at the position of each mode frequency. The transmission line is dispersionless up to about 500 GHz where the phase velocity begins to decrease. This is well below the gap frequency f(sub g) approx. equals 700 GHz. Results agree qualitatively with the expected theoretical behavior near f(sub g). This onset of dispersion and loss in Nb transmission lines will have a significant impact on the design of submillimeter wave RF circuits.

Javadi, H. H. S.↗

NASA NTRS1999

Measurement of Temperature Fluctuations and Microscopic Growth Rates in a Silicon Floating Zone and Microgravity

A silicon crystal growth experiment has been accomplished using the floating-zone technique under microgravity on a sounding rocket (TEXUS 36). Measurements of temperature fluctuations in the silicon melt zone due to time dependent thermocapillary convection (Marangoni convection) and an observation of the microscopic growth rate were simultaneously performed during the experiment. Temperature fluctuations of about 0.5 - 0.7 C with a frequency range < 0.5Hz were detectable. The microscopic growth rate fluctuates considerably around the average growth rate of 1 mm/min: Growth rates up to 3 to 4mm/min, close to zero mm/min, as well as negative values (backmelting) were observed. Dopant striations are clearly visible in the Sb-doped crystal. They were characterized by Spreading Resistance measurements and Differential Interference Contrast microscopy. The frequencies of temperature fluctuations, microscopic growth rates, and the dopant inhomogeneities correspond quite well, with main frequencies between 0.1 and 0.3 Hz. 3D numerical simulations were performed to predict the optimum position of the temperature sensor, and the characteristic temperature amplitudes and frequencies. At a position 3.4mm above the interface and 1.4mm inside the melt, equivalent to the sensor tip position in the experiment, temperature fluctuations up to 1.8 C and frequencies ? 0.25Hz were found in the simulations.

Schweizer, Markus↗

NASA NTRS2003

High-Temperature RF Probe Station For Device Characterization Through 500 deg C and 50 GHz

A high-temperature measurement system capable of performing on-wafer microwave testing of semiconductor devices has been developed. This high temperature probe station can characterize active and passive devices and circuits at temperatures ranging from room temperature to above 500 C. The heating system uses a ceramic heater mounted on an insulating block of NASA shuttle tile material. The temperature is adjusted by a graphical computer interface and is controlled by the software-based feedback loop. The system is used with a Hewlett-Packard 8510C Network Analyzer to measure scattering parameters over a frequency range of 1 to 50 GHz. The microwave probes, cables, and inspection microscope are all shielded to protect from heat damage. The high temperature probe station has been successfully used to characterize gold transmission lines on silicon carbide at temperatures up to 540 C.

Schwartz, Zachary D.↗

DOE OSTI2014

Quadrature conductivity: A quantitative indicator of bacterial abundance in porous media

ABSTRACT The abundance and growth stages of bacteria in subsurface porous media affect the concentrations and distributions of charged species within the solid-solution interfaces. Therefore, spectral induced polarization (SIP) measurements can be used to monitor changes in bacterial biomass and growth stage. Our goal was to gain a better understanding of the SIP response of bacteria present in a porous material. Bacterial cell surfaces possess an electric double layer and therefore become polarized in an electric field. We performed SIP measurements over the frequency range of 0.1–1 kHz on cell suspensions alone and cell suspensions mixed with sand at four pore water conductivities. We used Zymomonas mobilis at four different cell densities (in- cluding the background). The quadrature conductivity spectra exhibited two peaks, one around 0.05–0.10 Hz and the other around 1–10 Hz. Because SIP measurements on bacterial suspensions are typically made at frequencies greater than 1 Hz, these peaks have not been previously reported. In the bac-terial suspensions in growth medium, the quadrature conduc-tivity at peak I was linearly proportional to the density of the bacteria. For the case of the suspensions mixed with sands, we observed that peak II presented a smaller increase in the quadrature conductivity with the cell density. A comparison of the experiments with and without sand grains illustrated the effect of the porous medium on the overall quadrature con- ductivity response (decrease in the amplitude and shift of the peaks to the lower frequencies). Our results indicate that for a given porous medium, time-lapse SIP has potential for mon- itoring changes in bacterial abundance within porous media.

Zhang, Chi↗

NASA NTRS1989

An antenna for laser gravitational-wave observations in space

Progress during the past two years on a proposed Laser Gravitational-Wave Observatory in Space (LAGOS) is discussed. Calculated performance for a 10 to the 6th km sized antenna over the frequency range of 10 to the -5th to 1 Hz is given. The sensitivity from 0.001 to 0.1 Hz is expected to be 1 x 10 to the -21st/Hz exp 0.5. Noise sources such as accelerations of the drag-free test masses by random molecular impacts and by fluctuations in the net thermal radiation pressure will limit the sensitivity at lower frequencies. The scientific objectives are the observation of CW gravitational waves from large numbers of binary systems and the detection of pulses which may have been emitted during the period of galaxy formation.

Faller, J. E.↗

NASA NTRS1990

Low-frequency radio emissions at Neptune

The Voyager 2 plasma wave receiver detected weak radio emissions from Neptune's magnetosphere in the frequency range of 3 - 60 kHz. The emissions occurred in bursts lasting for typically 1.5 hours, often occurring twice per planetary rotation. Most of these radio bursts were detected within several degrees of the magnetic equatorial plane. During the passage through the magnetosphere, electrostatic upper hybrid resonance bands were observed close to the magnetic equator in conjunction with intensifications of the radio emissions at frequencies close to and above the upper hybrid bands. Further, near closest approach, the radio emissions were observed to cross the right-hand cutoff frequency with no apparent attenuation. It is concluded that the Neptunian radio emissions below about 60 kHz are produced by mode conversion from the upper hybrid waves and propagate in the ordinary mode into beams within about 12 deg of the magnetic equator. There is also evidence of an extraordinary mode emission at about 60 kHz which is apparently generated by an entirely different source from the escaping continuum radiation.

Kurth, W. S.↗