SEARCH · Engineering Papers

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Low-speed aerodynamic characteristics from wind-tunnel tests of a large-scale advanced arrow-wing supersonic-cruise transport concept

Tests have been conducted to extend the existing low speed aerodynamic data base of advanced supersonic-cruise arrow wing configurations. Principle configuration variables included wing leading-edge flap deflection, wing trailing-edge flap deflection, horizontal tail effectiveness, and fuselage forebody strakes. A limited investigation was also conducted to determine the low speed aerodynamic effects due to slotted training-edge flaps. Results of this investigation demonstrate that deflecting the wing leading-edge flaps downward to suppress the wing apex vortices provides improved static longitudinal stability; however, it also results in significantly reduced static directional stability. The use of a selected fuselage forebody strakes is found to be effective in increasing the level of positive static directional stability. Drooping the fuselage nose, which is required for low-speed pilot vision, significantly improves the later-directional trim characteristics.

Smith, P. M.↗

NASA NTRS1978

Comparison of concurrent strain gage- and pressure transducer-measured flight loads on a lifting reentry vehicle and correlation with wind tunnel predictions

Concurrent strain gage and pressure transducer measured flight loads on a lifting reentry vehicle are compared and correlated with wind tunnel-predicted loads. Subsonic, transonic, and supersonic aerodynamic loads are presented for the left fin and control surfaces of the X-24B lifting reentry vehicle. Typical left fin pressure distributions are shown. The effects of variations in angle of attack, angle of sideslip, and Mach number on the left fin loads and rudder hinge moments are presented in coefficient form. Also presented are the effects of variations in angle of attack and Mach number on the upper flap, lower flap, and aileron hinge-moment coefficients. The effects of variations in lower flap hinge moments due to changes in lower flap deflection and Mach number are presented in terms of coefficient slopes.

Tang, M. H.↗

NASA NTRS1978

EBF noise suppression and aerodynamic penalties

Acoustic tests were conducted at model scale to determine the noise produced in the flyover and sideline planes at reduced separation distances between the nozzle exhaust plane and the flaps of an under-the-wing (UTW) externally blown flap (EBF) configuration in its approach attitude. Tests were also made to determine the noise suppression effectiveness of two types of passive devices which were located on the jet impingement surfaces of the configuration. In addition, static aerodynamic performance data were obtained to evaluate the penalties produced by these suppression devices. Broadband low frequency noise reductions were achieved by reducing the separation distance between the nozzle and flaps. However, mid and high frequency noise was produced which exceeded that of the reference configuration. Two passive noise suppression devices located on the flaps produced moderate to large noise reductions at reduced separation distances. Consideration of the static aerodynamic performance data obtained for the configurations tested suggests that specific broadband noise suppression characteristics may be obtained through a trade-off with aerodynamic performance penalties by the careful selection of suppression devices.

Mckinzie, L. J., Jr.↗

NASA NTRS1979

Radiation of an acoustic source near the trailing edge of a wing in forward motion

The acoustic sources simulating engine or jet noise are located near the trailing edge. During landing or take-off operations the flap angle is not small. Solutions for the scattering of the acoustic sources, monopoles, dipoles or quadrupoles, by the wing with the flap at finite angle are constructed for the case that the acoustic wave length is much larger than the length of the flap but may be of the same order as the chord. For each given geometry of the flap and the position of the singularities, critical orientations of the dipoles and the quadrupoles are defined along which the noise becomes 'suppressed', i.e., the far field pressure becomes one order smaller.

Ting, L.↗

NASA NTRS1977

Two-dimensional wind-tunnel tests of a NASA supercritical airfoil with various high-lift systems. Volume 2: Test data

Three high lift systems for a 9.3 percent blunt based, supercritical airfoil were designed, fabricated, and wind tunnel tested. A method for calculating the viscous flow about two dimensional multicomponent airfoils was evaluated by comparing its predictions with test data. A comparison of high lift systems derived from supercritical airfoils with high lift systems derived from conventional airfoils is presented. The high lift systems for the supercritical airfoil were designed to achieve maximum lift and consisted of: (1) a single slotted flap, (2) a double slotted flap and a leading edge slat, and (3) a triple slotted flap and a leading edge slat. Aerodynamic force and moment data and surface pressure data are presented for all configurations and boundary layer and wake profiles for the single slotted flap configuration. The wind-tunnel models, test facilities and instrumentation, and data reduction are described.

Omar, E.↗

NASA NTRS1979

Experimental study of acoustic loads on an upper-surface-blown STOL airplane configuration

Fluctuating pressure levels were measured on the flap and fuselage of an upper-surface-blown jet-flap airplane configuration in a wind tunnel. The model tested had turbofan engines with a bypass ratio of 3 and a thrust rating of 10 kN. Rectangular nozzles were mounted flush with the upper surface at 35 percent of the wing chord. Test parameters were flap deflection angle, jet impingement angle, angle of attack, free-stream velocity, spanwise location of the engine, and jet dynamic pressure. Load levels were high throughout the jet impingement region, with the highest levels (about 159 dB) occurring on the fuselage and near the knee of the flap. The magnitude of the forward-velocity effect appeared to depend upon the ratio of free-stream and jet velocities. Good agreement was obtained between fluctuating pressure spectra measured at jet dynamic pressures of 7 and 22 kPa when the spectra were scaled by nondimensional functions of dynamic pressure, velocity, and the empirical relationship between dynamic pressure and overall fluctuating pressure level.

Willis, C. M.↗

NASA NTRS1980

Airframe Noise Reduction Studies and Clean-Airframe Noise Investigation

Acoustic wind tunnel tests were conducted of a wing model with modified leading edge slat and trailing edge flap. The modifications were intended to reduce the surface pressure response to convected turbulence and thereby reduce the airframe noise without changing the lift at constant incidence. Tests were conducted at 70.7 and 100 m/sec airspeeds, with Reynolds numbers 1.5 x 10 to the 6th power and 2.1 x 10 to the 6th power. Considerable reduction of noise radiation from the side edges of a 40 deflection single slotted flap was achieved by modification to the side edge regions or the leading edge region of the flap panel. Total far field noise was reduced 2 to 3 dB over several octaves of frequency. When these panels were installed as the aft panel of a 40 deg deflection double slotted flap, 2 dB noise reduction was achieved.

Fink, M. R.↗

NASA NTRS1980

Model tests of airframe noise reduction concepts

Trailing-edge flap and leading-edge slat models were modified to reduce their acoustic response to convected turbulence. These components were tested on an 0.3-m chord wing at 70.7 and 100 m/sec velocities in an acoustic wind tunnel. Noise radiation from the side edges of the 40 deg deflected flap was reduced by use of porous and perforated surface treatment along the leading- and side-edge region. Up to 2 to 3 dB reduction of total flap noise was achieved over a 3-octave range of frequency. Leading-edge slat noise was reduced about 2 dB by use of a perforated trailing-edge region on the slat. These reductions were retained when the modified slat and flaps were tested together.

Fink, M. R.↗

NASA NTRS1980

Results of a low-speed wind tunnel test of the MDC 2.2M supersonic cruise aircraft configuration

Results of a low speed test conducted in the Full Scale Tunnel at NASA Langley using an advanced supersonic cruise vehicle configuration are presented. These tests used a 10 percent scale model of a configuration that had demonstrated high aerodynamic performance at Mach 2.2 during a previous test program. The low speed model has leading and trailing edge flaps designed to improve low speed lift to drag ratios at high lift and includes devices for longitudinal and lateral/directional control. The results obtained during the low speed test program have shown that full span leading edge flaps are required for maximum performance. The amount of deflection of the leading edge flap must increase with C sub L to obtain the maximum benefit. Over 80 percent of full leading edge suction was obtained up to lift off C sub L's of 0.65. A mild pitch up occurred at about 6 deg angle of attack with and without the leading edge flap deflected. The pitch up is controllable with the horizontal tail. Spoilers were found to be preferable to spoiler/deflectors at low speeds. The vertical tail maintained effectiveness up to the highest angle of attack tested but the tail on directional stability deteriorated at high angles of attack. Lateral control was adequate for landing at 72 m/sec in a 15.4 m/sec crosswind.

Yip, L. P.↗

NASA NTRS1980

Flow visualization study of spanwise blowing applied to the F-4 fighter aircraft configuration

Water tunnel studies were performed to define the changes that occur in vortex flow fields above the wing due to spanwise blowing over the inboard and outboard wing panels and over the trailing-edge flaps. Flow visualization photographs were obtained for angles of attack up to 30 deg and sideslip angles up to 10 deg. The sensitivity of the vortex flows to changes in flap deflection angle, nozzle position, and jet momentum coefficient was determined. Deflection of the leading edge flap delayed flow separation and the formation of the wing vortex to higher angles of attack. Spanwise blowing delayed the breakdown of the wing vortex to farther outboard and to higher angles of attack. Spanwise blowing over the trailing edge flap entrained flow downward, producing a lift increase over a wide range of angles of attack. The sweep angle of the windward wing was effectively reduced in sideslip. This decreased the stability of the wing vortex, and it burst farther inboard. Reduced wing sweep required a higher blowing rate to maintain a stable vortex. A vortex could be stabilized on the outboard wing panel when an outboard blowing nozzle was used. Blowing from both an inboard and an outboard nozzle was found to have a favorable interaction.

Lorincz, D. J.↗

NASA NTRS1980

Use of multiblade sensors for on-line rotor tip-path plane estimation

Techniques are investigated for on-line estimation of rotor states in the nonrotating frame from multiple, simultaneous measurements in the rotating frame. The multiblade coordinate transformation is first applied to transform both flapping and flapping rate measurements into the nonrotating frame. The 'observer' approach is then used to generate algorithms for estimating tip-path plane rate and attitude from transformed flapping and flapping rate measurements. A numerical evaluation using simulated measurements is conducted to evaluate the performance of the algorithms and recommendations are made.

Du Val, R. W.↗

NASA NTRS1983

Flight measurements of hinged-plate wing-spoiler hinge moments

Hinge moment of hinged-plate wing spoilers were measured during flight of a twin turboprop airplane modified by the addition of upper and lower wing-surface spoilers. The spoiler-actuating hydraulic cylinders were instrumented to measure the forces required to extend the spoiler panels. Those measurements were converted to moment coefficient form, and are presented as a function of spoiler deployment angle. The hinge-moment data were collected at three flight conditions: with flaps extended at approach speed; with flaps retracted at a low speed; and with flaps retracted at a high speed (C sub L = 1.4, 1.0, and 0.5). In general, the magnitude of measured spoiler hinge moments were lower than predicted. Furthermore, for upper surface spoilers with flaps extended, the hinge moments increased in a discontinuous manner between spoiler deflection 10 and 10.

Fry, E. B.↗

NASA NTRS1985

Investigation of the Vortex Tab

An investigation was made into the drag reduction capability of vortex tabs on delta wing vortex flaps. The vortex tab is an up-deflected leading edge portion of the vortex flap. Tab deflection augments vortex suction on the flap, thus improving its thrust, but the tab itself is drag producing. Whether a net improvement in the drag reduction can be obtained with vortex tabs, in comparison with plane vortex flaps of the same total area, was the objective of this investigation. Wind tunnel tests were conducted on two models, and analytical studies were performed on one of them using a free vortex sheet theory.

Hoffler, K. D.↗

NASA NTRS1985

Experimentally determined flutter from two- and three-bladed model bearingless rotors in hover

A series of experiments was performed on a 1.8-m-diam model rotor in hover for the principal purpose of investigating the lead-lag stability of isolated bearingless rotors. Incidental to those tests, at least three types of pitch-flap flutter were encountered. Type 1 flutter occurred approximately at the second flap-mode frequency on both two-and three-bladed rotors for both small and large pitch angles and appeared to be a classic pitch-flap flutter. Type 2 flutter showed mostly torsional motion and was seen on both two- and three-bladed rotors. Type 3 flutter was a regressing flap flutter that occurred for only the three-bladed rotor configurations and appears to be a wake excited flutter. Although flutter occurred on a number of different configurations, no rotor parameters were identified that were clearly stabilizing or destabilizing.

Bousman, W. G.↗

NASA NTRS1986

Flight control system development and flight test experience with the F-111 mission adaptive wing aircraft

The wing on the NASA F-111 transonic aircraft technology airplane was modified to provide flexible leading and trailing edge flaps. This wing is known as the mission adaptive wing (MAW) because aerodynamic efficiency can be maintained at all speeds. Unlike a conventional wing, the MAW has no spoilers, external flap hinges, or fairings to break the smooth contour. The leading edge flaps and three-segment trailing edge flaps are controlled by a redundant fly-by-wire control system that features a dual digital primary system architecture providing roll and symmetric commands to the MAW control surfaces. A segregated analog backup system is provided in the event of a primary system failure. This paper discusses the design, development, testing, qualification, and flight test experience of the MAW primary and backup flight control systems.

Larson, R. R.↗

NASA NTRS1986

Flight control system development and flight test experience with the F-111 mission adaptive wing aircraft

Larson, R. R.↗

NASA NTRS1987

Flight investigation of the effects of an outboard wing-leading-edge modification on stall/spin characteristics of a low-wing, single-engine, T-tail light airplane

Flight tests were performed to investigate the change in stall/spin characteristics due to the addition of an outboard wing-leading-edge modification to a four-place, low-wing, single-engine, T-tail, general aviation research airplane. Stalls and attempted spins were performed for various weights, center of gravity positions, power settings, flap deflections, and landing-gear positions. Both stall behavior and wind resistance were improved compared with the baseline airplane. The latter would readily spin for all combinations of power settings, flap deflections, and aileron inputs, but the modified airplane did not spin at idle power or with flaps extended. With maximum power and flaps retracted, the modified airplane did enter spins with abused loadings or for certain combinations of maneuver and control input. The modified airplane tended to spin at a higher angle of attack than the baseline airplane.

Stough, H. Paul, III↗

NASA NTRS1986

Influence of dynamic inflow on the helicopter vertical response

A study was conducted to investigate the effects of dynamic inflow on rotor-blade flapping and vertical motion of the helicopter in hover. Linearized versions of two dynamic inflow models, one developed by Carpenter and Fridovich and the other by Pitt and Peters, were incorporated in simplified rotor-body models and were compared for variations in thrust coefficient and the blade Lock number. In addition, a comparison was made between the results of the linear analysis, and the transient and frequency responses measured in flight on the CH-47B variable-stability helicopter. Results indicate that the correlations are good, considering the simplified model used. The linear analysis also shows that dynamic inflow plays a key role in destabilizing the flapping mode. The destabilized flapping mode, along with the inflow mode that the dynamic inflow introduces, results in a large initial overshoot in the vertical acceleration response to an abrupt input in the collective pitch. This overshoot becomes more pronounced as either the thrust coefficient or the blade Lock number is reduced. Compared with Carpenter's inflow model, Pitt's model tends to produce more oscillatory responses because of the less stable flapping mode predicted by it.

Chen, Robert T. N.↗