Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrolyte additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

K 3 SbS 4 as a Potassium Superionic Conductor with Low Activation Energy for K–S Batteries

Abstract Solid‐state K‐ion conducting electrolytes are key elements to address the current problems in K secondary batteries. Here, we report a sulfide‐based K‐ion conductor K 3 SbS 4 with a low‐activation energy of 0.27 eV. W‐doped K 3− x Sb 1− x W x S 4 ( x =0.04, 0.06, 0.08, 0.10 and 0.12) compounds were also explored for increasing vacancy concentrations and improving ionic conductivity. Among them, K 2.92 Sb 0.92 W 0.08 S 4 exhibits the highest conductivity of 1.4×10 −4 S cm −1 at 40 °C, which is among the best reported potassium‐ion conductors at ambient temperature. In addition, K 2.92 Sb 0.92 W 0.08 S 4 is electrochemically stable with long‐chained potassium polysulfide of K 2 S x . A room‐temperature solid potassium–sulfur (K−S) battery system has therefore been successfully demonstrated, which is the first K−S battery prototype using non‐commercial inorganic‐based electrolyte to block the polysulfide shuttle.

25 ENERGY STORAGE↗

Fluid and electrolyte shifts in women during +Gz acceleration after 15 days' bed rest

Experiments were conducted on twelve women aged 23-34 yr - a bed rest (BR) group of eight subjects and an ambulatory (AMB) group of four subjects - to determine the effect of bed rest on shifts in plasma volume, electrolytes, and erythrocyte volume during +Gz acceleration on a centrifuge. The BR group underwent the +Gz acceleration during a two-week ambulatory control period, after 15 days of a 17-day BR period, and on the third day of ambulatory recovery. The AMB group underwent the same experimental procedures, but continued their normal daily routine during the BR period without additional prescribed physical exercise. Major conclusions are that (1) the higher the mean control tolerance, the greater the tolerance decline after BR; (2) relative confinement and reduced activity contribute as much to reduction in tolerance as does the horizontal body position during BR; (3) BR deconditioning has no effect on the erythrocyte volume during +3.0 Gz; and (4) about one-half the loss in tolerance after BR can be attributed to plasma volume and electrolyte shifts.

Greenleaf, J. E.↗

An Innovative Carbonate Fuel Cell Matrix, Abstract #188

The electrolyte matrix in direct carbonate fuel cell (DFC) is a microporous ceramic structure sandwiched between the electrodes to isolate the fuel from the oxidant, store electrolyte and facilitate ionic transport. FCE has advanced DFC electrolyte matrix over the years and demonstrated that the matrix meets the requirements for greater than 5 year life based on accelerated tests and field stack operations. However, development of advanced designs and materials that can further increase the performance and extend cell life will enable accelerated MCFC deployment. This paper will report the progress on the development of an unique and innovative matrix design that offers numerous benefits to the carbonate fuel cell performance and durability. In addition, this paper will also review parameters that affect matrix material stability and approaches to extend cell life.

08 HYDROGEN↗

Exploring the relationship between solvent-assisted ball milling, particle size, and sintering temperature in garnet-type solid electrolytes

Garnet-type solid electrolytes, such as Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO), are promising materials for solid-state batteries, but processing remains a challenge, in part due to the high sintering temperature required for densification. Additionally, this temperature can be lowered by decreasing the initial particle size via solvent-assisted ball milling, but the relationship between solvent choice, particle properties, sintering behavior, and ionic conductivity is not well understood. In this work, we systematically explore these parameters, showing that milling in commonly used protic solvents, such as alcohols, effectively decreases the particle size but results in lithium loss (through Li + /H + exchange) that leads to poor sintering. By contrast, milling in aprotic solvents with surfactant reduces the particle size to ~220 nm without lithium loss, enabling the fabrication of dense samples (5.1 g/cm 3 ) with good ionic conductivity (0.43 mS/cm at 25 °C) at a lower sintering temperature (1000 °C). We compare ionic conductivities and activation energies for samples prepared with different particle sizes and sintering temperatures and use multiphase-field simulations to identify the mass transport and microstructural mechanisms responsible for the observed sintering dependence on particle size. These results further clarify the relationship between processing parameters and performance and represent important progress toward overcoming fabrication challenges for these materials.

25 ENERGY STORAGE↗

1.3 V superwide potential window sponsored by Na-Mn-O plates as cathodes towards aqueous rechargeable sodium-ion batteries

Aqueous rechargeable sodium-ion batteries (ARSIBs) are highly desirable for the large-scale energy storage due to their inherent high safety and low-cost. Na-Mn-O electrode material has been considered as a promising cathode, yet the redox potential window is still not fully explored and utilized in aqueous rechargeable sodium-ion batteries. Herein, a chemical bonded Na 0.44 MnO 2 (NMO) plates are successfully synthesized via a polyvinylpyrrolidone-assisted sol-gel route followed by annealing process. The possibility of utilizing a wider potential window ranging between –0.3 V and 1.0 V vs. Ag/AgCl in mild aqueous electrolyte has been thus demonstrated by using NMO plates as cathodes for the first time. As a result, the as-synthesized NMO plates can deliver a highest initial discharge capacity of 77.2 mA h g –1 at a current density of 100 mA g –1 , compared with previous Na-Mn-O reports in mild aqueous electrolyte in ARSIBs. Even at a high rate of 500 mA g –1 , it still maintains a large capacity of 35 mA h g –1 after 1000 cycles, demonstrating its superior cycling stability. In addition, ex situ SEM and TEM-EDX results reveal that there is a newly formed sheet-like layer Na-birnessite Na 0.55 Mn 2 O 4 · 1.5H 2 O on the surface of NMO cathodes, which can provide extra ion channel for sodium ions and stabilize the electrode from pulverization, resulting in improved cycling stability. Furthermore, this study provides a broad implication for developing low-cost, high performance cathode materials to broaden the applied potential window towards high performance ARSIBs.

36 MATERIALS SCIENCE↗

Durability of symmetric-structured metal-supported solid oxide fuel cells

Symmetric-structure metal-supported solid oxide fuel cells (MS-SOFC) with YSZ electrolyte are fabricated with porous YSZ backbone electrodes, stainless steel supports, and infiltrated catalysts on both anode and cathode side. Durability towards aggressive thermal and redox cycling, and long-term operation is assessed. Additionally, many sealing material candidates are screened for compatibility with the cell materials and operating conditions, and a commercial sealing glass, GM31107, is selected. LSM/SDCN cells are then subjected to 200 very fast thermal cycles and 20 complete redox cycles, with minimal impact to cell performance. LSM/SDCN and SDCN/SDCN cells are operated for more than 1200 h at 700 °C. The seal and cell hermeticity is maintained, and cell ohmic impedance does not change significantly during operation. Electrode polarization increases during operation, leading to significant degradation of the cell performance. Lastly, in-operando EIS and post-mortem SEM/EDS analysis suggest that catalyst coarsening and cathode Cr deposition are the dominant degradation modes.

30 DIRECT ENERGY CONVERSION↗

Impact of ethylene carbonate on ion transport characteristics of PVdF-AgCF{sub 3}SO{sub 3} polymer electrolyte system

The ionic transport in thin film plasticized polymer electrolytes based on polyvinylidene fluoride (PVdF) as the polymer host, silver triflate (AgCF{sub 3}SO{sub 3}) as salt and ethylene carbonate (EC) as plasticizer prepared by solution casting technique has been reported. Addition of silver triflate has resulted in an increase in the room temperature (298 K) electrical conductivity of the polymer from 10{sup -6} to 10{sup -5} S cm{sup -1} whereas incorporation of EC as the plasticizer has further enhanced the conductivity value by an order of magnitude to 10{sup -4} S cm{sup -1} owing to the possible decrease in crystallinity of the polymer matrix as revealed by the detailed temperature-dependent complex impedance, silver ionic transference number, Fourier transform infrared and X-ray diffraction measurements.

36 MATERIALS SCIENCE↗

Conversion reaction of vanadium sulfide electrode in the lithium-ion cell: Reversible or not reversible?

With the increasing interest in transition metal chalcogenides, sulfide minerals containing the disulfide unit (S 2 2- ) have gained intensive attention for potential applications in energy storage devices, such as lithium-ion batteries (LIBs). Vanadium tetrasulfide (VS 4 ) possesses a unique linear-chain structure with a Peierls distortion and shows great promise for application in LIBs. However, its electrochemical reaction mechanism is still controversial, mainly due to the amorphous nature of the intermediates and final products. Here, by applying multiple X-ray spectroscopies, we reveal that VS 4 undergoes lithium intercalation and conversion reactions sequentially during the first discharge process, which are partially reversible in the subsequent charge process. However, an anomalous intercalation/conversion mixed reaction mechanism is dominant for the second cycle, mainly owing to the amorphization of the VS 4 electrode during the first cycle. In addition, the sulfur atoms are also involved in the redox reaction during cycling, with the anionic contribution of S 2 2- ↔ 2S 2- transformation. Furthermore, we find that the formation process of the solid electrolyte interphase is highly dynamic during the discharge and charge processes. Finally, the present study provides deeper insights into the complex reaction mechanism of VS 4 . This knowledge can accelerate the development of high-performance VS 4 -based electrode materials for LIBs.

36 MATERIALS SCIENCE↗

Utilizing ink composition to tune bulk-electrode gas transport, performance, and operational robustness for a Fe-N-C catalyst in polymer electrolyte fuel cell

With lower site density and turnover frequency, platinum group metal (PGM)-free catalysts based electrodes are often greater than 50 mu m thick in order to increase performance across the fuel cell operating range. Consequently, PGM-free electrodes have an additional bulk electrode transport resistance beyond the local or aggregate level transport in thin platinum-based electrodes. In parallel to the development of more active and durable PGM-free catalysts, advancements in understanding the interplay between PGM-free electrode fabrication, bulk-electrode transport, proton conductivity and performance are needed. Here, the relationship between ionic and gas phase transport through the electrode thickness is modified by adjusting electrocatalyst and ionomer flocculation/interaction at the ink level. The influence of the ink composition (water/n-propanol content) is examined via various in-situ electrochemical and ex-situ characterization techniques and the resulting electrode structure/performance relationship contrasted with electrode performance robustness across a range of relative humidity (RH). For the electrocatalyst examined here, a water-rich (82 wt% H2O) ink formulation was favorable for operation at high RH due to improved molecular diffusion through larger electrode pores. In contrast, the improved interactions between ionomer and electrocatalyst enabled a more robust electrode and higher performance during low RH operation for the 50 wt% H2O content ink.

08 HYDROGEN↗

Electrochemically Assisted Single Crystal Growth of Reduced Preyssler Polyoxometalates Decorated with M 2+ ( M = Co, Ni) and Cubane–Like Ni 4 O 4 Units

Polyoxometalates (POMs) are of great interest to the scientific community, and their reduction and nucleation have been well–established by multi–step techniques. The present study develops an electrochemical approach for simultaneous reduction and nucleation of polyoxometalate–containing solids. Herein we report crystal growth of reduced Preyssler polyoxotungstate–based (anionic formula [NaP 5 W 30 O 110 ] 14– ) new crystalline solids made of Preyssler anions interlinked by Co 2+ and Ni 2+ ions. Crystal nucleation and in situ reduction were achieved at room temperature using a two silver wire electrode setup in various aqueous solutions under constant applied potentials. The POM material was deposited on the cathode, and its structure was characterized by X–ray diffraction techniques. The primary structure type observed involves POMs decorated by disordered Co 2+ /Ni 2+ octahedra and fused into 1–D pillars by additional Co 2+ /Ni 2+ octahedra. Additionally, a secondary phase was observed in the Ni–based reactions, where reduced Preyssler anions are decorated by Ni 4 O 4 cubane–like units. To understand the electrochemical process, polarization curves of the electrolyte solutions are presented, suggesting an applied potential best suited for crystal growth. The work highlights the effectiveness of an electrochemical pathway where nucleation and simultaneous reduction of POMs can make novel reduced POM solids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Prospects for Employing Lithium Copper Phosphates as High-Voltage Li-Ion Cathodes

Three compositions of lithium copper phosphates: Li 2 CuPO 4 , Li 2 Cu 5 (PO 4 ) 4 , and Li 2 CuP 2 O 7 have been studied as potential high-voltage cathode materials for Li-ion batteries, following computational predictions of high operating voltages. An assisted-microwave preparation of Li 2 CuPO 4 , which is otherwise difficult to prepare in nearly pure form, has been developed. The electrochemical performance of all three compounds has been investigated. Additionally, the cyclability of these materials is found to be poor due to structural changes, irreversible reduction to metallic copper at potentials as high as 2.5 V, and the possibility of dissolution into the electrolyte. Some general understanding in regard to the use of Cu compounds in redox electrodes is presented.

25 ENERGY STORAGE↗

Defect formation and microstructure tuning via proton irradiation to control electrochemical and phase reversibility in layered battery materials

The reversibility of phase transformation influences the functionality of electrode materials in batteries. In many battery materials, nanosized grains favor phase reversibility but at the cost of cyclability due to aggravated side reactions with the electrolyte. Here, in this study, we present a novel approach to enhance the phase transformation reversibility of layered oxide cathodes, exemplified by Na 2/3 Fe 1/2 Mn 1/2 O 2 through proton irradiation. In addition to forming defects, proton irradiation at sufficiently high doses can subdivide single grains into multiple nanodomains without physically rupturing them. Hence, the single grains of the material assume a pseudo-secondary particle nature without reducing the overall grain size. Preserving the grain size is advantageous, as it reduces side reactions, which is not possible with conventional grain size reduction methods. While chemical transformations and defect formation induced through proton irradiation can influence the stability of battery materials, it is expected that structural reorganization due to cycling-induced phase transformation will be contained within these nanodomains. Such confinement of phase transformation is potentially responsible for enhancing the reversibility of layered oxide materials in our study. Thus, our study suggests that grain subdivision could become an effective microstructure tuning strategy for managing electrochemical cycling-induced phase changes in battery electrodes.

25 ENERGY STORAGE↗

Process for making manganese dioxide and its polymorphs reversible

A method of forming a layered manganese dioxide for use in a cathode of a battery comprises disposing a cathode into a housing of an electrochemical cell, disposing an anode into the housing, disposing a polymeric separator between the anode and the cathode such that the anode and the cathode are electrically separated, adding an alkaline electrolyte to the housing, cycling the electrochemical cell into the 2nd electron capacity of the manganese dioxide, and forming a layered manganese dioxide having a layered manganese dioxide structure with the one or more additives incorporated into the layered manganese dioxide structure. The cathode comprising a cathode material comprising: a manganese dioxide compound, one or more additives selected from the group consisting of bismuth, copper, tin, lead, silver, cobalt, nickel, magnesium, aluminum, potassium, lithium, calcium, gold, antimony, iron, zinc, and combinations thereof, and a conductive carbon.

Yadav, Gautam G.↗

Potassium Prussian blue-coated Li-rich cathode with enhanced lithium ion storage property

With high specific capacity, the layered Li-rich Mn-based oxide (LRMO) is a promising candidate cathode material for Li-ion batteries. However, the irreversible release of Li-ions during the first charging process, instability of LRMO/electrolyte interface and relatively low ion conductivity of LRMO result in low initial Coulombic efficiency (ICE), poor cycle stability and rate performance, which prohibit its further application. Furthermore, interface engineering via additive coating is expected to effectively address these issues. Herein, we rely on potassium Prussian blue (KPB), a Li + acceptor with good ion conductivity, as a new coating material on LRMO particles. The KPB coating not only forms a protective layer on the surface of LRMO against electrolyte corrosion, but also functions as a host for Li + transport and accommodation, leading to enhanced ion conductivity and ICE of LRMO cathode. Consequently, 2 wt% KPB coated LRMO cathode achieved an initial discharge capacity of up to 281.7 mA h g -1 with an ICE of 85.69% compared to an ICE of 79.52% for the LRMO cathode without coating. The cycling and rate performance are also greatly improved as evidenced by the well maintained capacity of up to 176.8 mA h g -1 after 100 cycles at a current density of 0.5 C, compared to the limited capacity of only 135.3 mA h g -1 for the LRMO cathode without coating. Overall, this work pioneers the use of potassium Prussian blue as additive coating material to enhance performance of LRMO cathode, and we expect it to inspire the battery community with new strategies of material engineering/design toward practical application in high-energy lithium-ion batteries.

25 ENERGY STORAGE↗

Electrolytically Assisted Surface Decontamination (EASD{sup TM}) for POCO Operations - 20282

NNL in collaboration with C-Tech Innovation Ltd and Sellafield Ltd has been exploring innovative technologies to enable a significant reduction of radiological hazards within facilities during the Post Operational Clean Out (POCO) phase of a nuclear plant's life cycle. Reducing the hazard by effectively decontaminating plants in-situ during POCO delivers huge cost reductions for future decommissioning operations. These cost reduction benefits are realized by reducing the number and complexity of remote operations as well as lowering the long-term waste disposal costs. Whilst chemical decontamination can achieve the desired level of decontamination, applying aggressive chemical reagents is hazardous, potentially difficult to control and requires there to be complimentary effluent treatment and waste routes. This work has aimed to develop flexible and controllable decontamination processes which could be operated without the additional complexity and issues associated with chemical decontamination. The processes needed to be relatively fast and effective to minimize the time operators would spend in an active area. In addition, there was a driver to produce decontamination methodologies which generated a secondary waste compatible with current routes and which takes advantage of current waste capacity. The strategy therefore was to come up with a solution that works with, rather than against, the science and engineering behind process plants at Sellafield. Electrolytically Assisted Surface Decontamination (EASD{sup TM}) is an innovative electrochemical decontamination process (developed by NNL and C-Tech Innovation Ltd) that can remove activity from contaminated metal in very short time periods. Application of the patented electric waveform to the surface when treating contaminated metal with nitric acid has been shown to significantly enhance the decontamination performance. When compared to proposed baseline washout procedures at Sellafield, the only change to the process is the applied electrical waveform which is temporary and controllable. The current causes dissolution of the metal surface being decontaminated which leads to activity transferring from the plant item into the nitric acid effluent stream. This innovation has the potential to transform the POCO process and allow a nitric acid based washout approach to deliver POCO quickly and cost effectively within the existing infrastructure. Several devices have now been designed that incorporate this EASD{sup TM} technology and enable the decontamination process to be applied to a range items commonly identified as being contaminated during nuclear decommissioning programmes such as pipework, tanks and hotspots of walls/floors. Inactive and active laboratory-scale testing has been completed using both simulated and 'real-life' contaminated (low level waste) metallic items retrieved from different nuclear sites. Active trials demonstrated that contaminated items could be treated to free release levels within minutes. Engineering scale tests are currently being performed, with guidance from Sellafield's system engineers and plant managers, to provide the necessary re-assurance the designed devices could be successfully deployed in an on-plant scenario. The final stage of this development work is to carry out an active demonstration of the decontamination technology on Thorp at Sellafield. This paper aims to highlight progress made to date with the EASD{sup TM} technology and, more specifically, the development of an in-situ decontamination device for deployment within radioactive pipework. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Pressure effects on lithium anode/nickel-manganese-cobalt oxide cathode pouch cells through fixture design

Applying external pressure to a pouch cell results in improved performance, implicating systems-level design of batteries. Here, different formats and amounts of external pressure to Li-Li x Ni 0.8 Mn 0.1 Co 0.1 O 2 (Li-NMC811) pouch cells were studied under lean electrolyte conditions. Due to the more uniform lithium plating/stripping, a constant gap fixture that retains the distance of the frame during cycling performed greater than a constant pressure fixture that retains applied pressure to the cell. In addition, the use of flexible foam in a constant gap fixture revealed enhanced cycle life at 10 psi; however, at 30 psi, the use of a rigid plate extended cycle life to over 250 cycles, while the foam severely shortened cycle life. This discrepancy with pressure was proven to be driven by stress distribution on cell components. The failure mechanisms and the effects of pressure fixture design on cell components were unveiled, shedding light on improving high-energy battery performance through at-scale fixture design.

25 - ENERGY STORAGE↗

Nanotechnology for Sulfur Cathodes

The field of lithium-sulfur batteries has benefited enormously from the advances in nanotechnology. At each step of technological improvement, lithium-sulfur batteries have relied upon techniques and methodologies brought upon by nanotechnology. Nanoporous material, heterogeneous nanocomposite, and hierarchical electrode developments have all been well-established as critical milestones for lithium-sulfur batteries. Overall, this review will briefly discuss the specific major roles of nanotechnology in lithium-sulfur batteries regarding practically relevant testing conditions in addition to research trends and future directions for electrocatalysis.

25 ENERGY STORAGE↗

Electrochemical and Chemical Reactivities of Titanium Oxide-Based Materials with a Chloroaluminate Ionic Liquid Electrolyte for Aluminum Batteries

Here, by selecting three different types of electrode materials, we intended to better understand the Al 3+ intercalation chemistry of titanium oxide-based frameworks with an acidic chloroaluminate electrolyte. In agreement with previous reports, we confirmed that the native interstitial sites of anatase TiO 2 are less prone to accommodate Al 3 + than Li + or Na + ions, while introducing cationic vacancies largely increases the electrochemical storage capacity. Upon the first cycle, the highest reversible capacity, up to 277 mAh/g, was obtained for a hydrated layered structure featuring cationic vacancies. Total scattering data showed that the insertion of Al 3+ ions induced a strong distortion of the framework. In addition, combined 27 Al MAS NMR and DFT calculations revealed that in oxy-hydroxylated vacant sites, the coordination mode of Al 3+ ions depends on the arrangement of anions around vacancies inducing the occurrence of 4-, 5-, and 6-fold coordination modes. Further cycling experiments revealed a progressive capacity fading for all electrode materials. Using cyclic voltammetry on the used electrolyte, we evidenced that a partial dissolution has occurred, which is more pronounced for the layered hydrate compound, and that solubilized species are electrochemically active, giving rise to specific signatures in both CVs and galvanostatic experiments. Raman spectroscopy enabled us to characterize these species, which are derived from the Ti-Cl system. The solubilized species, however, eventually precipitated, as shown by a purple deposit observed on the separator and tentatively assigned to TiCl 3 , known to be insoluble in this medium. By providing further information on the Al 3+ intercalation chemistry and a better understanding of the electrochemical and chemical reactivities of electrode materials, this work will enable progress to be made in the development of aluminum-ion batteries.

Al3+-ion insertion chemistry↗