Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dielectrics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

LDEF SP-HVDE (Space Plasma-High Voltage Drainage Experiment) post-flight results: Leakage current and discharge

TRW designed and fabricated two identical SP-HVDE trays which were flown in the NASA LDEF (Long Duration Exposure Facility) for 5.75 years in the LEO (low earth orbit) environment. One tray was placed near the leading edge and one near the trailing edge, and investigations were performed to compare the environmental interactions on the dielectric samples of the two trays. Each tray consisted of six assemblies with Kapton dielectric samples of varying thicknesses (i.e., 2 mils, 3 mil, and 5 mils) biased under +/- 300 V, +/- 500 V, and +/- 1000 V. The original objective was successfully achieved by measuring the first in-flight average leakage current through the samples. Less than 5 percent of the post-flight coulometers behaved anomalously. The data should be valuable to the design and evaluation of spacecraft with high voltage systems. M/D (micrometeoroid and debris) impacts over the dielectric samples were examined using a SEM (Scanning Electron Microscope) and an EDS (Energy Dispersive x-ray Spectrometer). These impact sites were sprayed by silver which were most likely caused either by the impact or a 'local ESD' (electrostatic discharge).

Yaung, J. Y.↗
NASA NTRS1992

Electrical breakdown of Space Station Freedom surfaces

Space Station Freedom (SSF) will be the largest and highest power spacecraft that the U.S. has put into orbit. The solar array will generate 160 volts nominal when in sunlight, and the present baseline design is for the negative end of the solar array to be tied to SSF structure. Due to the balance of leakage currents through the plasma, the structure will be driven approximately 140 volts negative of the ambient conductive ionospheric plasma. Surface materials such as anodized aluminum will have this voltage drop across a thin dielectric which may not have sufficient dielectric strength to prevent dielectric breakdown. This can lead to arcing on the exterior surfaces of Space Station.

Carruth, M. R., Jr.↗
NASA NTRS1992

Venus: Geochemical conclusions from the Magellan data

Though the Magellan mission was not designed to collect geochemical or petrological information, it has done so nonetheless. Since the time of the Pioneer Venus mission it has been known that high-altitude (greater than 2.5-5 km) mountainous areas on Venus exhibit anomalously low radiothermal emissivity (e less than 0.6). Magellan has greatly refined and extended these observations. The low emissivity requires surface material in the uplands to have a mineralogical composition that gives it a high bulk dielectric constant, greater than 20. The dielectric constant of dry terrestrial volcanic rocks seldom exceeds 7. The high-dielectric character of high-altitude surface material cannot be a primary property of the local volcanic rock, because there is no reason why rock having the required special mineralogy would erupt only at high altitudes. Therefore it is a secondary property; the primary Venus rock has reacted with the atmosphere to form a mineralogically different surface layer, and the secondary minerals formed are controlled by the ambient temperature, which decreases with altitude on Venus. A further investigation of venusian mineralogy is presented.

Wood, J. A.↗
NASA NTRS1993

Moment method analysis of linearly tapered slot antennas

A method of moments (MOM) model for the analysis of the Linearly Tapered Slot Antenna (LTSA) is developed and implemented. The model employs an unequal size rectangular sectioning for conducting parts of the antenna. Piecewise sinusoidal basis functions are used for the expansion of conductor current. The effect of the dielectric is incorporated in the model by using equivalent volume polarization current density and solving the equivalent problem in free-space. The feed section of the antenna including the microstripline is handled rigorously in the MOM model by including slotline short circuit and microstripline currents among the unknowns. Comparison with measurements is made to demonstrate the validity of the model for both the air case and the dielectric case. Validity of the model is also verified by extending the model to handle the analysis of the skew-plate antenna and comparing the results to those of a skew-segmentation modeling results of the same structure and to available data in the literature. Variation of the radiation pattern for the air LTSA with length, height, and taper angle is investigated, and the results are tabulated. Numerical results for the effect of the dielectric thickness and permittivity are presented.

Koeksal, Adnan↗
NASA NTRS1993

Microwave characterization of slotline on high resistivity silicon for antenna feed network

Conventional silicon wafers have low resistivity and consequently unacceptably high value of dielectric attenuation constant. Microwave circuits for phased array antenna systems fabricated on these wafers therefore have low efficiency. By choosing a silicon substrate with sufficiently high resistivity it is possible to make the dielectric attenuation constant of the interconnecting microwave transmission lines approach those of GaAs or InP. In order for this to be possible, the transmission lines must be characterized. In this presentation, the effective dielectric constant (epsilon sub eff) and attenuation constant (alpha) of a slotline on high resistivity (5000 to 10 000 ohm-cm) silicon wafer will be discussed. The epsilon sub eff and alpha are determined from the measured resonant frequencies and the corresponding insertion loss of a slotline ring resonator. The results for slotline will be compared with microstrip line and coplanar waveguide.

Simons, Rainee N.↗
NASA NTRS1991

Method for calculating and observing microwave absorption by a sphere in a single mode rectangular cavity

A new theory of microwave absorption by a lossy dielectric sphere in a single mode rectangular cavity has been recently developed. The absorption was treated in the framework of an electromagnetic scattering problem. That theory is summarized here and calculated results that bear on optimizing the processing of materials are illustrated. Methods for observing power absorption and other results predicted by the scattering model are discussed. Cavity perturbation theory provides a bridge between theoretical calculations and experimental observations, and a special problem that arises when an established version of cavity perturbation theory is applied to spheres is identified, analyzed, and resolved. The direct problem of predicting shifts in frequency and Q from model calculations is discussed for a sphere in a cavity when the sphere's complex dielectric constant is known. Also, the inverse problem of determining the complex dielectric constants from measured values of those shifts is considered. The small sphere limit, where an electrostatic or quasistatic model is valid, is treated in detail, and planned work on parallel problems for larger spheres is described.

Jackson, H. W.↗
NASA NTRS1993

Ellipsometric characterization of In(0.52)Al(0.48)As and of modulation doped field effect transistor structures on InP substrates

The dielectric function of a thick layer of In(0.52)Al(0.48)As lattice matched to InP was measured by variable angle spectroscopic ellipsometry in the range 1.9-4.1 eV. The In(0.52)Al(0.48)As was protected from oxidation using a thin In(0.53)Ga(0.47)As cap that was mathematically removed for the dielectric function estimate. The In(0.52)Al(0.48)As dielectric function was then verified by ellipsometric measurements of other In(0.53)Ga(0.47)As/In(0.52)Al(0.48)As structures, including (MODFET), and is shown to provide accurate structure layer thicknesses.

Alterovitz, S. A.↗
NASA NTRS1993

The Brewster angle effect in SAR polarimetry

For the double bounce case, where the radar signal is reflected twice before returning to the radar antenna, some polarization effects may be observed related to the dielectric constant of the two surfaces causing the reflections. The most noticeable effect would be that the returned signal would be preferentially H polarized. In fact, it may be possible to discern the Brewster angle for both surfaces. The locations of the Brewster angle will depend on the dielectric constant and permittivity of each surface. If it is assumed that both reflections are in the same plane of incidence, and that both surfaces are smooth and flat, there is a straightforward relationship between the degree of linear polarization m and both the dielectric constants of the two reflecting surfaces and the angle of incidence of the illuminating wave: m carat = cos 2(arccot (square root of (R(sub v) / R(sub h)))) where R(sub v,h) are the V and H polarized Fresnel reflection coefficients for two surfaces perpendicular to each other. The degree of linear polarization may be calculated from AIRSAR compressed Stokes data and compared with the given equation. The degree of linear polarization may also be calculated using tree models and compared with AIRSAR data. With further work, it may be possible to use the degree of linear polarization to determine surface parameters of certain imaged areas.

Chapman, B.↗
NASA NTRS1994

Surface property variations in Venusian fluidized ejecta blanket craters

A comprehensive study of Magellan Cycles 1 and 2 radar data from Venus reveals surface roughness and dielectric variations associated with fluidized ejecta blanket (FEB) craters that help illuminate styles of flow ejecta emplacement. This study develops new procedures of digital unit mapping and polygon-filling algorithms using Magellan synthetic aperture radar (SAR), altimetry, and radiometry data. These techniques allow the extraction of radiophysical information for FEB crater materials, nearby plains, and lava flows. Backscatter curve slopes of the FEBs studied here are consistent with surface textures that are transitional between a'a and pahoehoe-like. Average surface property values of ejecta units are relatively similar for a given crater, but are discernibly different from other craters. Individual crater ejecta reflectivity and emissivity values are relatively similar to those for the surrounding plains, which may suggest a link between plains material and ejecta dielectric properties. Increasing FEB roughness downflow are interpreted to be associated with more lava-like flows, while decreasing roughness are more similar to trends typical of gravity (pyroclastic-like or debris-like) flows. Most commonly, FEB crater flow materials exhibit transitions from proximal, lava/melt-like flow styles to distal, gravity flow-like styles. Some FEBs show more complicated behavior, however, or appear to be more dominated by dielectric differences downflow, as inferred from correlations between the data sets. Such transitions may result from changes in local topography or from overlapping of flow lobes during FEB emplacement.

Johnson, Jeffrey R.↗
NASA NTRS1995

Multilayer Thin-Film Microcapacitors

Miniature capacitors containing multiple alternating thin-film dielectric and metal layers proposed, especially for use in integrated and hybrid electronic circuits. Because capacitance inversely proportional to thickness of dielectric layers, use of thin, high-quality dielectric layers affords capacitance and energy-storage densities much greater than now available. These devices much smaller and more reliable than state-of-art capacitors.

Thakoor, Sarita↗
NASA NTRS1996

Microwave Resonators Containing Diamond Disks

Synthetic diamond dielectric bodies proposed for use in cylindrical resonators helping to stabilize frequencies of some microwave oscillators. Acting in conjunction with metal resonator cavities in which mounted, such dielectric bodies support "whispering-gallery" waveguide modes characterized by desired frequencies of resonance and by electro-magnetic-field configurations limiting dissipation of power on metal surfaces outside dielectric bodies. Performances at room temperature might exceed those of liquid-nitrogen-cooled sapphire-based resonators.

Dick, G. John↗
NASA NTRS1996

Electrorheological Fluids: Aerospace Applications

Electrorheological fluids (ERF) are an intriguing class of non-Newtonian industrial fluids. They consist of fine dielectric particles suspended in liquids of low dielectric constants. The objectives of this research were to select a particulate system such that: (1) its density can be varied to match that of the selected liquid, and (2) the dielectric constant of the particles and the liquids should be such that the critical fields needed for asymptotic increase in viscosity are less than or equal to 10 KV/cm. Synthetic Zeolite particles were selected as the solute/suspensions. Octoil oil was selected as the solvent. The results are summarized here.

Parmar, D. S.↗
NASA NTRS1995

Langley Research Center - Soluble Imide (LaRC-SI)

This report is about experimenting and developing uses for the new thermal plastic developed by Dr. Robert Bryant called the 'Langley Research Center - Soluble Imide' (LaRC-SI). The three developments are: the use of the LaRC-SI as a dielectric for thin film sensors, as an adhesive to place diamonds on surfaces to increase thermal conductivity, and as an intermediate layer to allow the placement of metal on aluminum nitride. The LaRC-SI was developed by Dr. Robert G. Bryant, a chemical engineer at NASA Langley Research Center. The unique properties of this material is that it is an amorphous thermoplastic. This means that it can be reformed at elevated temperature and pressures. It can be applied in the form of a spray, spin, dip coating, paint, or spread with a doctors blade. The LaRC-SI has excellent adhesive and dielectric properties. It can also be recycled. Potential applications for this material are resin for mechanical parts such as gears, bearings and valves, advanced composites like carbon fiber, high strength adhesives, thin film circuits, and as a dielectric film for placing electrical components on conductive materials.

Stang, David↗
NASA NTRS1996

Design and Laboratory Validation of a Capacitive Sensor for Measuring the Recession of Thin-Layered Ablator

Flight vehicles are typically instrumented with subsurface thermocouples to estimate heat transfer at the surface using inverse analysis procedures. If the vehicle has an ablating heat shield, however, temperature time histories from subsurface thermocouples no longer provide enough information to estimate heat flux at the surface. In this situation, the geometry changes and thermal energy leaves the surface in the form of ablation products. The ablation rate is required to estimate heat transfer to the surface. A new concept for a capacitive sensor has been developed to measure ablator depth using the ablator's dielectric effect on a capacitor's fringe region. Relying on the capacitor's fringe region enables the gage to be flush mounted in the vehicle's permanent structure and not intrude into the ablative heat shield applied over the gage. This sensor's design allows nonintrusive measurement of the thickness of dielectric materials, in particular, the recession rates of low-temperature ablators applied in thin (0.020 to 0.060 in. (0.05 to 0.15 mm)) layers. Twenty capacitive gages with 13 different sensing element geometries were designed, fabricated, and tested. A two-dimensional finite-element analysis was performed on several candidate geometries. Calibration procedures using ablator-simulating shims are described. A one-to-one correspondence between system output and dielectric material thickness was observed out to a thickness of 0.055 in. (1.4 mm) for a material with a permittivity about three times that of air or vacuum. A novel method of monitoring the change in sensor capacitance was developed. This technical memorandum suggests further improvements in gage design and fabrication techniques.

Gregory K Noffz↗
NASA NTRS1993

Microwave Scattering Model for Grass Blade Structures

In this paper, the electromagnetic scattering solution for a grass blade with complex cross-section geometry is considered. It is assumed that the blade cross section is electrically small, but its length is large compared to the incident wavelength. In a recent study it has been shown that the scattering solution for such problems, in the form of a polarizability tensor, can be obtained using the low-frequency approximation in conjunction with the method of moments. In addition, the study shows that the relationship between the polarizability tensor of a dielectric cylinder and its dielectric constant can be approximated by a simple algebraic expression. The results of this study are used to show that this algebraic approximation is valid also for cylinders with cross sections the shape of grass blades, providing that proper values am selected for each of three constants appearing in the expression. These constants are dependent on cylinder shape, and if the relationship between the constants and the three parameters describing a grass blade shape can be determined, an algebraic approximation relating polarizability tensor to blade shape, as well as dielectric constant, can be formed. Since the elements of the polarizability tensor are dependent on only these parameters, this algebraic approximation can replace the cumbersome method of moments model. A conjugate gradient method is then implemented to correctly determine the three constants of the algebraic approximation for each blade shape. A third-order polynomial fit to the data is then determined for each constant, thus providing a complete analytic replacement to the numerical (moment method) scattering model. Comparisons of this approximation to the numerical model show an average error of less than 3%.

Stiles, James M.↗
NASA NTRS1997

Validation of an Accurate Three-Dimensional Helical Slow-Wave Circuit Model

The helical slow-wave circuit embodies a helical coil of rectangular tape supported in a metal barrel by dielectric support rods. Although the helix slow-wave circuit remains the mainstay of the traveling-wave tube (TWT) industry because of its exceptionally wide bandwidth, a full helical circuit, without significant dimensional approximations, has not been successfully modeled until now. Numerous attempts have been made to analyze the helical slow-wave circuit so that the performance could be accurately predicted without actually building it, but because of its complex geometry, many geometrical approximations became necessary rendering the previous models inaccurate. In the course of this research it has been demonstrated that using the simulation code, MAFIA, the helical structure can be modeled with actual tape width and thickness, dielectric support rod geometry and materials. To demonstrate the accuracy of the MAFIA model, the cold-test parameters including dispersion, on-axis interaction impedance and attenuation have been calculated for several helical TWT slow-wave circuits with a variety of support rod geometries including rectangular and T-shaped rods, as well as various support rod materials including isotropic, anisotropic and partially metal coated dielectrics. Compared with experimentally measured results, the agreement is excellent. With the accuracy of the MAFIA helical model validated, the code was used to investigate several conventional geometric approximations in an attempt to obtain the most computationally efficient model. Several simplifications were made to a standard model including replacing the helical tape with filaments, and replacing rectangular support rods with shapes conforming to the cylindrical coordinate system with effective permittivity. The approximate models are compared with the standard model in terms of cold-test characteristics and computational time. The model was also used to determine the sensitivity of various circuit parameters including typical manufacturing dimensional tolerances and support rod permittivity. By varying the circuit parameters of an accurate model using MAFIA, these sensitivities can be computed for manufacturing concerns, and design optimization previous to fabrication, thus eliminating the need for costly experimental iterations. Several variations were made to a standard helical circuit using MAFIA to investigate the effect that variations on helical tape and support rod width, metallized loading height and support rod permittivity, have on TWT cold-test characteristics.

Kory, Carol L.↗
NASA NTRS1996

YBCO High-Temperature Superconducting Filters on M-Plane Sapphire Substrates

Since the discovery of High Temperature Superconductors (HTS) in 1986, microwave circuits have been demonstrated using HTS films on various substrates. These HTS-based circuits have proven to operate with less power loss than their metallic film counterparts at 77 K. This translates into smaller and lighter microwave circuits for space communication systems such as multiplexer filter banks. High quality HTS films have conventionally been deposited on lanthanum aluminate (LaAlO3) substrates. However, LaAlO3 has a relative dielectric constant (epsilon(sub r)) of 24. With a epsilon(sub r) approx. 9.4-11.6, sapphire (Al2O3) would be a preferable substrate for the fabrication of HTS-based components since the lower dielectric constant would permit wider microstrip lines to be used in filter design, since the lower dielectric constant would permit wider microstrip lines to be used for a given characteristic impedance (Z(sub 0)), thus lowering the insertion losses and increasing the power handling capabilities of the devices. We report on the fabrication and characterization of YBa2Cu3O(7-delta) (YBCO) on M-plane sapphire bandpass filters at 4.0 GHz. For a YBCO 'hairpin' filter, a minimum insertion loss of 0.5 dB was measured at 77 K as compared with 1.4 dB for its gold counterpart. In an 'edge-coupled' configuration, the insertion loss went down from 0.9 dB for the gold film to 0.8 dB for the YBCO film at the same temperature.

Sabataitis, J. C.↗
NASA NTRS1997

Thin Film Multilayer Conductor/Ferroelectric Tunable Microwave Components for Communication Applications

High Temperature Superconductor/Ferroelectric (HTS/FE ) thin film multilayered structures deposited onto dielectric substrates are currently being investigated for use in low loss, tunable microwave components for satellite and ground based communications. The main goal for this technology is to achieve maximum tunability while keeping the microwave losses as low as possible, so as to avoid performance degradation when replacing conventional technology (e.g., filters and oscillators) with HTS/FE components. Therefore, for HTS/FE components to be successfully integrated into current working systems, full optimization of the material and electrical properties of the ferroelectric films, without degrading those of the HTS film; is required. Hence, aspects such as the appropriate type of ferroelectric and optimization of the deposition conditions (e.g., deposition temperature) should be carefully considered. The tunability range as well as the microwave losses of the desired varactor (i.e., tunable component) are also dependent on the geometry chosen (e.g., parallel plate capacitor, interdigital capacitor, coplanar waveguide, etc.). In addition, the performance of the circuit is dependent on the location of the varactor in the circuit and the biasing circuitry. In this paper, we will present our results on the study of the SrTiO3/YBa2Cu3O(7-delta)/LaAl03 (STO/YBCO/LAO) and the Ba(x)Sr(1-x)TiO3/YBa2Cu3O(7-delta)/LaAl03(BSTO/YBCO/ILAO) HTS/FE multilayered structures. We have observed that the amount of variation of the dielectric constant upon the application of a dc electric field is closely related to the microstructure of the film. The largest tuning of the STO/YBCO/LAO structure corresponded to single-phased, epitaxial STO films deposited at 800 C and with a thickness of 500 nm. Higher temperatures resulted in interfacial degradation and poor film quality, while lower deposition temperatures resulted in films with lower dielectric constants, lower tunabilities, and higher losses. For STO/LAO multilayer structures having STO film of similar quality we have observed that interdigital capacitor configurations allow for higher tunabilities and lower losses than parallel plate configurations, but required higher dc voltage. Results on the use of these geometries in working microwave components such as filters and stabilizing resonators for local oscillators (LO) will be discussed.

Miranda, Felix A.↗