SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electromagnetic interference in deep-space network receiver is often caused by stray coupling from power lines. These stray signals create potential differences between ground terminals, which leads to excessive noise in receiver circuits. Pair of probes detect and measure noise currents in conductors.
A three-dimensional electromagnetic inverse scattering identity, based on the physical optics approximation, is developed for the monostatic scattered far field cross section of perfect conductors. Uniqueness of this inverse identity is proven. This identity requires complete scattering information for all frequencies and aspect angles. A nonsingular integral equation is developed for the arbitrary case of incomplete frequence and/or aspect angle scattering information. A general closed-form solution to this integral equation is developed, which yields the shape of the scatterer from such incomplete information. A specific practical radar solution is presented. The resolution of this solution is developed, yielding short-pulse target resolution radar system parameter equations. The special cases of two- and one-dimensional inverse scattering and the special case of a priori knowledge of scatterer symmetry are treated in some detail. The merits of this solution over the conventional radar imaging technique are discussed.
A number of fundamentally ultra-reliable, all-magnetic logic circuits are developed using as a basis a single element ferrite structure wired as a logic delay element. By making minor additions or changes to the basic wiring pattern of the delay element other logic functions such as OR, AND, NEGATION, MAJORITY, EXCLUSIVE-OR, and FAN-OUT are developed. These logic functions are then used in the design of a full-adder, a set/reset flip-flop, and an edge detector. As a demonstration of the utility of all the developed devices, an 8-bit, all-magnetic, logic arithmetic unit capable of controlled addition, subtraction, and multiplication is designed. A new basic ferrite logic element and associated complementary logic scheme with the potential of improved performance is also described. Finally, an improved batch process for fabricating joint-free power drive and logic interconnect conductors for this basic class of all-magnetic logic is presented.
The results of the development and testing of ferrite monolithic memory arrays are presented. This development required the synthesis of ferrite materials having special magnetic and physical characteristics and the development of special processes; (1) for making flexible sheets (laminae) of the ferrite composition, (2) for embedding conductors in ferrite, and (3) bonding ferrite laminae together to form a monolithic structure. Major problems encountered in each of these areas and their solutions are discussed. Twenty-two full-size arrays were fabricated and fired during the development of these processes. The majority of these arrays were tested for their memory characteristics as well as for their physical characteristics and the results are presented. The arrays produced during this program meet the essential goals and demonstrate the feasibility of fabricating monolithic ferrite memory arrays by the processes developed.
By the use of fractional factorials, paths of steepest ascent and direct comparison experimentation, performance characteristics of the CuF2/LiAsF6-MF/Li electrochemical system were optimized under conditions of temperature environment, discharge rate, active stand, and use of anhydrous cathodes. Two hundred ampere-hours/lb of CuF2 and 600 watt-hours/lb of CuF2 were achieved in anhydrous cells at plus 40 C and at a discharge rate of 10 ma sq cm. Electrical performance is primarily altered by temperature and discharge rate; however, other factors such as cathode water content, cathode conductor content, separator thickness, and the use of SO2 gas also have significant effects.
The capability to automatically route, remove insulation from, and weld small-diameter solid conductor wire is presented. This would facilitate the economical small-quantity production of complex miniature electronic assemblies. An engineering model of equipment having this capability was developed and evaluated. Whereas early work in the use of welded magnet wire interconnections was concentrated on opposed electrode systems, and generally used heat to melt the wire insulation, the present method is based on a concentric electrode system and a wire feed system which splits the insulation by application of pressure prior to welding. The work deals with the design, fabrication, and evaluation testing of an improved version of this concentric electrode system. Two different approaches to feeding the wire to the concentric electrodes were investigated. It was concluded that the process is feasible for the interconnection of complex miniature electronic assemblies.
The importance of material selection is stressed in the design and manufacture of FCC. Several applications of flat conductor cable are discussed relative to material selection and the reasons for using a particular material for each application is explained.
The results are presented of study effort whose aim was the development of accurate means of analyzing and predicting signal cross-talk in multi-wire digital data cables. A complete analytical model is developed n + 1 wire systems of uniform transmission lines with arbitrary linear boundary conditions. In addition, a minimum set of parameter measurements required for the application of the model are presented. Comparisons between cross-talk predicted by this model and actual measured cross-talk are shown for a six conductor ribbon cable.
NASA flat conductor cable connectors with individually sealed contacts are described. Descriptions of the design, main features, contact spring, connector electrical data, dimensions and weight, FCC termination, and keying system for plug and receptacle are included.
The techniques and hardware are described which were developed for facilitating the use of flexible flat conductor cable (FFCC) in commercial air transports. The system was designed as an evolutionary transition from the current round wire harnessing to the use of FFCC harnesses. The equipment discussed includes the pressure crimp barrel designed for terminating FFCC, reel-fed applicator, cable connectors and adaptors, and equipment racks.
The application of flat conductor cable technology to surface mounted homewiring was investigated. Baseboard concepts, safety aspects, problems, and advantages are discussed.
The application requirements and manufacturing techniques for the flat conductor cable used in the Viking Lander Articulated Boom Unit are described. The Viking Boom is a 3-axis device utilized to position a soil sampler and provide digging forces. This application imposed severe restrictions on size, weight, materials, and choice of manufacturing processes. The final cable assembly design resulted in a combination of collated cable and flexible circuits assembled by resistance welding techniques.
A prototype facility comprising a superconducting magnetic suspension and balance and a supersonic wind tunnel was developed with the objectives of (1) establishing the feasibility of applying the 3-component magnetic balance concept to dynamic stability studies, and (2) investigating design concepts and parameters that are critical for extrapolation to large-scale systems. Many important design and operational aspects as well as safety considerations are dictated by the cryogenic nature of this advanced-technology facility. Results of initial tests demonstrate that super-conductors can be utilized safely and efficiently for wind tunnel magnetic suspensions. At the present stage of development of this facility, controlled one-dimensional support of a spherical model was achieved.
A high torque motor with improved servo mechanism is reported. Armature windings are cast into an epoxy cylinder and armature conductors are integrally cast with an aluminum mounting ring which provides thermal conductance directly into the structure. This configuration eliminates magnetic hysteresis because there is no relative motion between the rotating magnetic field and any stationary iron. The absence of destabilization forces provides a fast electrical response compared with a typical torquer of conventional construction.
An apparatus for measuring the thermoelectric properties of materials under high pressure is described that includes a pair of force transmitting assemblies constructed of thermally and electrically conductive material positioned between the ram and anvil of a press. Each force transmitting assembly has a small diameter pressing portion for contacting a face of the sample so that the sample can be squeezed between them. Each assembly also includes a heat exchanger to maintain the sample face at a controlled temperature, and an electrical conductor to carry current generated by the sample. A sleeve of thermally and electrically insulative material closely surrounds the pressing portions of the two assemblies.
The electrical and electrochemical properties of V-5 and V-7 vanadium oxides were investigated. The effects of pressure, temperature and moisture on the bulk resistivity of the oxides in powder, sintered, and crystalline form were determined, and the static and dynamic volt-ampere characteristics were obtained. Sintered samples tested showed better electrical stability than the compressed powder samples. Two types of commercially available vanadium pentoxide were heat-treated to obtain various crystalline oxide forms which were mounted on alumina substrates and terminated by thick-film conductors for making electrical connections. Indications are that these materials could have applications as sensors, critical-temperature resistors, high-speed switches, and temperature-compensation elements in hybrid microelectronic circuits.
Switch presently provides remote control switching, by radio signals, or pollution sampling devices. Can be used for remote weather station interrogation, firing of pyrotechnics, control of dangerous equipment, or control of device in location where it is impractical to run metallic conductors because of time limitations, distance, or terrain.
Plug-in flat packs and flat conductor cable (FCC) can be used to make compact, lightweight, external monitoring system requiring minimum of hard wiring. Microelectronic monitoring panel includes replaceable integrated or hybrid circuit flat packs and FCC.