Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Static longitudinal aerodynamic characteristics of close-coupled wing-canard configurations at Mach numbers from 1.60 to 2.86

An experimental investigation was made in the Mach number range from 1.60 to 2.86 to determine the static longitudinal aerodynamic characteristics of close-coupled wing-canard configurations. Three canards, ranging in exposed planform area from 17.5 to 30.0 percent of the wing reference area, were employed in this investigation. The canards were either located in the plane of the wing or in a position 18.5 percent of the wing mean geometric chord above the wing plane. Most data obtained were for a model with a 60 deg leading-edge-sweep wing; however, a small amount of data were obtained for a 44 deg leading-edge-sweep wing. The model utilized two balances to isolate interference effects between wing and canard. In general, it was determined that at angle of attack for all configurations investigated with the canard in the plane of the wing an unfavorable interference exists which causes the additional lift on the canard generated by a canard deflection to be lost on the wing due to an increased downwash at the wing from the canard. Further, this interference decreased somewhat with increasing Mach number. Raising the canard above the plane of the wing also greatly decreased the interference of the canard deflection on the wing lift. However, at Mach 2.86 the presence of the canard in the high position had a greater unfavorable interference effect at high angles of attack than the canard in the wing plane. This interference resulted in the in-plane canard having better trimmed performance at Mach 2.86 for the same center-of-gravity location.

Dollyhigh, S. M.↗
NASA NTRS1974

Estimation of nonlinear aerodynamic derivatives of a variable geometry fighter aircraft from flight data

This paper is concerned with the estimation of stability and control parameters of a high performance fighter aircraft from data obtained from high angle of attack flight. The estimation process utilizes a maximum likelihood algorithm derived for the case of a nonlinear aerodynamic force and moment model. The aircraft used was a high speed variable sweep heavy weight fighter with twin vertical tails. Comparisons of results from the nonlinear analysis are made with linear theory and wind tunnel results when available.

Ramachandran, S.↗
NASA NTRS1975

Aerodynamic characteristics of a large aircraft to transport space shuttle orbiter or other external payloads

Wind tunnel tests were conducted in the Langley V/STOL tunnel to determine the aerodynamic characteristics of a large transport aircraft designed to carry the space shuttle orbiter or orbiter booster tank. Results indicate that the transport, with or without payloads, is statically stable, the longitudinal static margins being rather excessive. Elevator power is sufficient to trim the transport up to stall except when the orbiter is mounted close to the wing. Maximum lift-drag ratios at wind tunnel Reynolds numbers vary from 12 to 14 depending on model configuration. Tests were conducted at Reynolds numbers from 1.21 x 1 million to 1.49 x 1 million with angle of attack from -2 deg to 20 deg and angle of sideslip from -5 deg to 5 deg.

Paulson, J. W., Jr.↗
NASA NTRS1979

Aircraft wake flow effect and horizontal tail buffet

As part of a program to investigate the fluctuating pressure distribution and response behavior of a fighter aircraft in transonic maneuver, an F-5A scale model has previously been tested in an 11-ft transonic wind tunnel. The model, with a number of static and dynamic pressure transducers imbedded in the lifting surfaces was tested at various angles of attack up to 16 deg. In this paper, test results of particular interest to wake flow and horizontal tail buffet are described. It is shown that the dynamic pressure data on the tail surface at the specified flight conditions serve to determine the local dynamic loads. They also influence the control performance of the aircraft under maneuver conditions where buffet is encountered. The data presented demonstrate a number of contributing factors that affect the tail dynamic pressures in the transonic regime.

Hwang, C.↗
NASA NTRS1980

NASA general aviation stall/spin flight testing

A comprehensive program incorporating spin tunnel, static and rotary balance wind tunnel, full scale wind tunnel, free flight radio control model, flight simulation, and full scale flight testing was undertaken. Work includes aerodynamic definition of various configurations at high angles of attack, testing of stall and spin prevention concepts, definition of spin and spin recovery characteristics, and development of test techniques and emergency spin recovery systems. Some of the more interesting results to date are presented for the first airplane in the program in the areas of tail design, wind leading edge design, mass distribution, center of gravity location, and small airframe changes, with associated pilot observations. Design philosophy of the spin recovery parachute system is discussed, in addition to test techniques.

Patton, J. M., Jr.↗
NASA NTRS1980

Predicted vortex shedding from noncircular bodies in supersonic flow

A method to predict nose vortex shedding from circular and noncircular bodies in supersonic flow at angles of attack and roll is presented. The body is represented by a supersonic panel method, and the lee side vortex wake is modeled by discrete vortices in crossflow planes. The three-dimensional steady flow problem is reduced to a two-dimensional, unsteady, separated flow problem for solution. Comparison of measured and predicted surface pressure distributions, flow field surveys, and aerodynamic characteristics are presented for circular and elliptic bodies.

Mendenhall, M. R.↗
NASA NTRS1983

Acoustic measurements of a full-scale coaxial hingeless rotor helicopter

Acoustic data were obtained during a full-scale test of the XH-59A Advancing Blade Concept Technology Demonstrator in the 40- by 80-Foot Wind Tunnel. The XH-59A is a research helicopter with two coaxial rotors and hingeless blades. Performance, vibration, and noise at various forward speeds, rotor lift coefficients and rotor shaft angles of attack were investigated. The noise data were acquired over an isolated rotor lift coefficient range of 0.024 to 0.162, an advance ratio range of 0.23 to 0.45 corresponding to tunnel wind speeds of 89 to 160 knots, and angles of attack from 0 deg to 10 deg. Acoustic data are presented for seven microphone locations for all run conditions where the model noise is above the background noise. Model test configuration and performance information are also listed. Acoustic waveforms, dBA, and 1/3-octave spectra as functions of operating condition for selected data points and microphones are presented. In general, the noise level is shown to increase with rotor lift coefficient except under certain operating conditions where significant impulsive blade/vortex interactions increase noise levels.

Peterson, R. L.↗
NASA NTRS1985

Nacelle/pylon/wing integration on a transport model with a natural laminar flow nacelle

Tests were conducted in the Langley 16-Foot Transonic Tunnel at free-stream Mach numbers from 0.70 to 0.82 and angles of attack from -2.5 deg to 4.0 deg to determine if nacelle/pylon/wing integration affects the achievement of natural laminar flow on a long-duct flow-through nacelle for a high-wing transonic transport configuration. In order to fully assess the integration effect on a nacelle designed to achieve laminar flow, the effects of fixed and free nacelle transitions as well as nacelle longitudinal position and pylon contouring were obtained. The results indicate that the ability to achieve laminar flow on the nacelle is not significantly altered by nacelle/pylon/wing integration. The increment in installed drag between free and fixed transition for the nacelles on symmetrical pylons is essentially the calculated differences between turbulent and laminar flow on the nacelles. The installed drag of the contoured pylon is less than that of the symmetrical pylon. The installed drag for the nacelles in a rearward position is greater than that for the nacelles in a forward position.

Lamb, M.↗
NASA NTRS1986

Influence of airfoil mean loading on convected gust interaction noise

A theoretical model is developed for the noise generated when a convected vortical or entropic gust encounters an airfoil at nonzero angle of attack. The analysis is based on Rapid Distortion Theory. High frequency gusts, whose wavelengths are short compared to the airfoil chord, are considered. The noise generation is shown to be concentrated near the airfoil leading edge. The level of the generated noise is increased by airfoil mean loading, with the appropriate scaling parameter being the local leading edge incidence angle. The trailing edge simply scatters the leading edge sound field, and here the mean loading effects scale on the airfoil total lift. Calculations are presented which illustrate that, at high frequencies, moderate levels of airfoil steady loading can dramatically increase the noise produced by airfoil convected gust interactions.

Kerschen, E. J.↗
NASA NTRS1991

Flow Visualization Study of a 1/48-Scale AFTI/F111 Model to Investigate Horizontal Tail Flow Disturbances

During flight testing of the AFTI/F111 aircraft, horizontal tail buffet was observed. Flutter analysis ruled out any aeroelastic instability, so a water-tunnel flow visualization study was conducted to investigate possible flow disturbances on the horizontal tail which might cause buffet. For this study, a 1/48-scale model was used. Four different wing cambers and one horizontal tail setting were tested between 0 and 20 deg angle of attack. These wing cambers corresponded to the following leading training edge deflections: 0/2, 10/10, 10/2, and 0/10. Flow visualization results in the form of still photographs are presented for each of the four wing cambers between 8 and 12 deg angle of attack. In general, the horizontal tail experiences flow disturbances which become more pronounced with angle of attack or wing trailing-edge deflection.

Bjarke, Lisa J.↗
NASA NTRS1992

An improved PNS scheme for predicting complex three-dimensional hypersonic flows

Upwinding is incorporated into a numerical technique for predicting hypersonic viscous flows over lifting configurations at moderate angles of attack. A general real-gas flux-vector-splitting technique based on Van Leer's (1982) approach is employed to model upwinding, and three techniques are examined for flux-vector differencing. The three methods are evaluated by applying them to an axisymmetric configuration with a 10-deg afterbody flare. The results indicate that an oscillation-free shock front can be described by using first-order full upwinding across the embedded shock and central-differencing for the other zones. This combined approach is found to be highly convergent for the near-wall region, and its performance is examined for predicting a Mach 15 flow over a finned missile. Attention is given to the effects of gas chemistry which can significantly affect the flows over the missile configurations.

Bhutta, Bilal A.↗
NASA NTRS1992

The balance and harmony of control power for a combat aircraft in tactical maneuvering

An analysis is presented for a family of regular extremal attitude-maneuvers for the High Angle-of-Attack Research Vehicle that has thrust-vectoring capability. Different levels of dynamic coupling are identified in the combat aircraft attitude model, and the characteristic extremal-family motion is explained. It is shown why the extremal-family trajectories develop small sideslip-angles, a highly desirable feature from a practical viewpoint.

Bocvarov, Spiro↗
NASA NTRS1992

Sonic boom prediction for the Langley Mach 2 low-boom configuration

Sonic boom pressure signatures and aerodynamic force data for the Langley Mach 2 low sonic boom configuration were computed using the TranAir full-potential code. A solution-adaptive Cartesian grid scheme is utilized to compute off-body flow field data. Computations were performed with and without nacelles at several angles of attack. Force and moment data were computed to measure nacelle effects on the aerodynamic characteristics and sonic boom footprints of the model. Pressure signatures were computed both on and off ground-track. Near-field pressure signature computations on ground-track were in good agreement with experimental data. Computed off ground-track signatures showed that maximum pressure peaks were located off ground-track and were significantly higher than the signatures on ground-track. Bow shocks from the nacelle inlets increased lift and drag, and also increased the magnitude of the maximum pressure both on and off ground-track.

Madson, Michael D.↗
NASA NTRS1933

Wind tunnel research concerning lateral control devices, particularly at high angles of attack VII : Handley Page tip and full-span slots with ailerons and spoilers

Tests were made with ordinary ailerons and different sizes of spoilers on rectangular Clark Y wing models with Handley Page tip and full span slots. The tests showed the effect of the control devices on the general performance of the wings as well as on the lateral control and lateral stability characteristics.

Weick, Fred E↗
NASA NTRS1935

Wind-tunnel research comparing lateral control devices, particularly at high angles of attack XII : upper-surface ailerons on wings with split flaps

This report covers the twelfth of a series of tests conducted to compare different lateral control devices with particular reference to their effectiveness at high angles of attack. The present wind tunnel tests were made with two sizes of upper-surface ailerons on rectangular Clark Y wing models equipped with full span split flaps. The tests showed the effect of the upper-surface ailerons and of the split flaps on the general performance characteristics of the wings, and on the lateral controllability and stability characteristics. The results are compared with those for plain wings with ordinary ailerons of similar sizes.

Weick, Fred E↗
NASA NTRS1946

Flight Investigation at High Speeds of the Drag of Three Airfoils and a Circular Cylinder Representing Full-Scale Propeller Shanks

Tests have been made at high speeds to determine the drag of models, simulating propeller shanks, in the form of a circular cylinder and three airfoils, the NACA 16-025, the NACA 16-040, and the NACA 16-040 with the rear 25 percent chord cut off. All the models had a maximum thickness of 4 1/2 inches to conform with average propeller-shank dimensions and a span of 20 1/4 inches. For the tests the models were supported perpendicular to the lower surface of the wing of an XP-51 airplane. A wake-survey rake mounted below the wing directly behind the models was used to determine profile drag of Mach numbers of 0.3 to 0.8 over a small range of angle of attack. The drag of the cylinder was also determined from pressure-distribution and force measurements.

Barlow, William H↗
NASA NTRS1934

Stipa Monoplane with Venturi Fuselage

This report presents a detailed examination of the factors that went into the design of the Stipa monoplane. The model tested in the wind tunnel was made dissymmetrical externally, in order to produce a lift even at an angle of attack of 0 degrees with respect to the longitudinal axis of the tube.

Luigi Stipa↗
NASA NTRS1994

Installed F/A-18 inlet flow calculations at 30 degrees angle-of-attack: A comparative study

NASA Lewis is currently engaged in a research effort as a team member of the High Alpha Technology Program (HATP) within NASA. This program utilizes a specially equipped F/A-18, the High Alpha Research Vehicle (HARV), in an ambitious effort to improve the maneuverability of high-performance military aircraft at low subsonic speed, high angle of attack conditions. The overall objective of the Lewis effort is to develop inlet technology that will ensure efficient airflow delivery to the engine during these maneuvers. One part of the Lewis approach utilizes computational fluid dynamics codes to predict the installed performance of inlets for these highly maneuverable aircraft. Full Navier-Stokes (FNS) calculations on the installed F/A-18 inlet at 30 degrees angle of attack, 0 degrees yaw, and a freestream Mach number of 0.2 have been obtained in this study using an algebraic turbulence model with two grids (original and revised). Results obtained with the original grid were used to determine where further grid refinements and additional geometry were needed. In order to account properly for the external effects, the forebody, leading edge extension (LEX), ramp, and wing were included with inlet geometry. In the original grid, the diverter, LEX slot, and leading edge flap were not included due to insufficient geometry definition, but were included in a revised grid. In addition, a thin-layer Navier-Stokes (TLNS) code is used with the revised grid and the numerical results are compared to those obtained with the FNS code. The TLNS code was used to evaluate the effects on the solution using a code with more recent CFD developments such as upwinding with TVD schemes versus central differencing with artificial dissipation. The calculations are compared to a limited amount of available experimental data. The predicted forebody/fuselage surface static pressures compared well with data of all solutions. The predicted trajectory of the vortex generated under the LEX was different for each solution. These discrepancies are attributed to differences in the grid resolution and turbulence modeling. All solutions predict that this vortex is ingested by the inlet. The predicted inlet total pressure recoveries are lower than data and the distortions are higher than data. The results obtained with the revised grid were significantly improved from the original grid results. The original grid results indicated the ingested vortex migrated to the engine face and caused additional distortions to those already present due to secondary flow development. The revised grid results indicate that the ingested vortex is dissipated along the inlet duct inboard wall. The TLNS results indicate the flow at the engine face was much more distorted than the FNS results and is attributed to the pole boundary condition introducing numerical distortions into the flow field.

Smith, C. Frederic↗