Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “atomic force microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Surface and magnetic characteristics of Ni-Mn-Ga/Si (100) thin film

Polycrystalline Ni-Mn-Ga thin films have been deposited on Si (100) substrate with different film thickness. The influence of film thickness on the phase structure and magnetic domain of the films has been examined by scanning electron microscope, atomic force microscopy and magnetic force microscopy. Analysis of structural parameters indicates that the film at lower thickness exhibits the coexistence of both austenite and martensite phase, whereas at higher thickness L1{sub 2} cubic non magnetic phase is noticed. The grains size and the surface roughness increase along with the film thickness and attain the maximum of 45 nm and 34.96 nm, respectively. At lower film thickness, the magnetic stripe domain is found like maze pattern with dark and bright images, while at higher thickness the absence of stripe domains is observed. The magnetic results reveal that the films strongly depend on their phase structure and microstructure which influence by the film thickness.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fabricating Ohmic contact on Nb-doped SrTiO{sub 3} surface in nanoscale

Fabricating reliable nano-Ohmic contact on wide gap semiconductors is an important yet difficult step in oxide nanoelectronics. We fabricated Ohmic contact on the n-type wide gap oxide Nb-doped SrTiO{sub 3} in nanoscale by mechanically scratching the surface using an atomic force microscopy tip. Although contacted to high work function metal, the scratched area exhibits nearly linear IV behavior with low contact resistance, which maintains for hours in vacuum. In contrast, the unscratched area shows Fowler–Nordheim tunneling dominated Schottky rectifying behavior with high contact resistance. It was found that the Ohmic conductivity in the scratched area was drastically suppressed by oxygen gas indicating the oxygen vacancy origin of the Ohmic behavior. The surface oxygen vacancy induced barrier width reduction was proposed to explain the phenomena. The nanoscale approach is also applicable to macroscopic devices and has potential application in all-oxide devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Phase Segregation in Polystyrene?Polylactide Blends

Spun-cast films of polystyrene (PS) blended with polylactide (PLA) were visualized and characterized using atomic force microscopy (AFM) and synchrotron-based X-ray photoemission electron microscopy (X-PEEM). The composition of the two polymers in these systems was determined by quantitative chemical analysis of near-edge X-ray absorption signals recorded with X-PEEM. The surface morphology depends on the ratio of the two components, the total polymer concentration, and the temperature of vacuum annealing. For most of the blends examined, PS is the continuous phase with PLA existing in discrete domains or segregated to the air?polymer interface. Phase segregation was improved with further annealing. A phase inversion occurred when films of a 40:60 PS:PLA blend (0.7 wt percent loading) were annealed above the glass transition temperature (Tg) of PLA.

36 MATERIALS SCIENCE↗

Comparison of structural properties of pristine and gamma irradiated single-wall carbon nanotubes: Effects of medium and irradiation dose

A systematic study of the gamma irradiation effects on single wall carbon nanotube (SWCNT) structure was conducted. Nanotubes were exposed to different doses of gamma irradiation in three media. Irradiation was carried out in air, water and aqueous ammonia. Thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), elemental analysis (EA) and Raman spectroscopy confirmed the changes in the SWCNT structure. TGA measurements showed the highest percentage of introduced groups for the SWCNTs irradiated with 100 kGy. FTIR spectroscopy provided evidence for the attachment of hydroxyl, carboxyl and nitrile functional groups to the SWCNT sidewalls. Those groups were confirmed by EA. All irradiated SWCNTs had hydroxyl and carboxyl groups irrelevant to media used for irradiation, but nitrile functional groups were only identified in SWCNTs irradiated in aqueous ammonia. Raman spectroscopy indicated that the degree of disorder in the carbon nanotube structure correlates with the irradiation dose. For the nanotubes irradiated with the dose of 100 kGy, the Raman I{sub D}/I{sub G} ratio was three times higher than for the pristine ones. Atomic force microscopy showed a 50% decrease in nanotube length at a radiation dose of 100 kGy. Scanning and transmission electron microscopies showed significant changes in the morphology and structure of gamma irradiated SWCNTs. - Highlights: Black-Right-Pointing-Pointer Gamma irradiation causes SWCNT covalent functionalization. Black-Right-Pointing-Pointer Type of covalently attached groups to SWCNT surface depends on irradiation medium. Black-Right-Pointing-Pointer The SWCNT shortening level increases with applied irradiation dose. Black-Right-Pointing-Pointer The average length of carbon nanotubes decreased by 50% at the highest dose. Black-Right-Pointing-Pointer The diameter of SWCNT bundles becomes small as irradiation dose rises.

36 MATERIALS SCIENCE↗

Surface acoustic wave velocity of gold films deposited on silicon substrates at different temperatures

Au thin films have been deposited by DC magnetron sputtering on Si (001) substrates at different substrate temperatures, ranging from 200 K to 450 K. With increasing temperature, the expected crystallinity and morphology of the Au thin film are clearly improved, as shown by x ray diffraction, atomic force microscopy and scanning electron microscopy experiments. Parallel to this, the surface acoustic wave propagation velocity shows a clear enhancement toward the ideal values obtained from numerical simulations of a Au thin film on Si (001) substrate. Moreover, a very thin and slightly rough interlayer between the Si (001) substrate and the Au thin film is developed for temperatures above 350 K. The composition and nature of this interlayer is not known. This interlayer may be responsible for the steep change in the structural and elastic properties of the Au thin films at the higher temperatures and possibly also for an improvement of the adhesion properties of the Au on the Si (001) substrate.

36 MATERIALS SCIENCE↗

Electropolymerization of a bifunctional ionic liquid monomer yields as electroactive liquid-crystalline polymer.

The preparation and polymerization of a bifunctional imidazolium-based ionic liquid (IL) monomer that incorporates both a vinyl group and a thiophene moiety is reported. Potentiodynamic electropolymerization of the monomer produces an optically birefringent polymer film that strongly adheres to the electrode surface. Fourier transform IR spectroscopy shows that polymerization occurs through both the vinyl and thienyl groups. Cylic voltammetry (CV) is used to determine the polymer oxidation potential (1.66 V) and electrochemical bandgap, Eg, of 2.45 eV. The polymer exhibits electrochromism, converting from yellow in the neutral form ({lambda}{sub max} = 380 nm) to blue in the polaronic state at 0.6 V ({lambda}{sub max} = 672 nm) and to blue-grey in the bipolaronic state at 1.2 V ({lambda}{sub max} > 800 nm). Topographic atomic force microscopy (AFM) images reveal isolated (separated) fibrils. Grazing-incidence small-angle X-ray scattering (GISAXS) studies indicate a lamellar structure with a lattice spacing of 3.2 nm. Wide-angle X-ray diffraction (WAXD) studies further suggest that the polymerized thiophene sheets are oriented perpendicular to the polymerized vinylimidazolium. The electrical conductivity, as determined by four-probe dc conductivity measurements was found to be 0.53 S cm{sup -1} in the neutral form and 2.36 S cm{sup -1} in the iodine-doped state, values higher than typically observed for polyalkylthiophenes. The structural ordering is believed to contribute to the observed enhancement of the electrical conductivity.

36 MATERIALS SCIENCE↗

Growth and magnetic property of {zeta}-phase Mn{sub 2}N{sub 1{+-}x} thin films by plasma-assisted molecular beam epitaxy

{zeta}-phase manganese nitride films were directly grown on sapphire substrates using plasma-assisted molecular beam epitaxy. Mn{sub 2}N{sub 1.06}, Mn{sub 2}N{sub 0.98}, and Mn{sub 2}N{sub 0.86} films were synthesized by controlling the temperature of the effusion cell filled with highly pure manganese powder. The composition, structure, and morphology of the films were identified by x-ray photoelectron spectroscopy, x-ray diffraction and atomic force microscopy, and the magnetic properties of the films were characterized by a superconducting quantum interference device magnetometer at 5 and 300 K. The magnetic measurements reveal that Mn{sub 2}N{sub 1{+-}x} exhibits weak ferromagnetism at 5 K, which is mainly ascribed to the weak interaction among the Mn cations induced by the nitrogen vacancies. Furthermore, the Mn{sub 2}N{sub 0.86} single-crystalline films are found to have room-temperature ferromagnetism, which is attributed to the strain of the Mn{sub 2}N{sub 0.86} films raised from lattice mismatch between the Mn{sub 2}N{sub 0.86} films and the substrates.

36 MATERIALS SCIENCE↗

Modifications of local structures of Gd{sub 2}O{sub 3} on incorporation of SiO{sub 2}

In the present work we have reported the results of investigations on local structures of e-beam evaporated (Gd{sub 2}O{sub 3}-SiO{sub 2}) composite thin films by synchrotron based EXAFS measurements. The evolution of local structure in the case of the Gd{sub 2}O{sub 3}-SiO{sub 2} system is found to be different from the HfO{sub 2}-SiO{sub 2} system reported by us earlier. The EXAFS analysis has shown that the Gd-O bond length decreases monotonically as SiO{sub 2} content in the films increases. Also the amplitudes of the peaks in the FT-EXAFS spectra of the samples, which depend jointly on the coordination numbers as well as the Debye-Waller factors (measure of disorder) are found to decrease monotonically with increase in SiO{sub 2} contents in the Gd{sub 2}O{sub 3} matrix. Atomic force microscopy (AFM) measurements of the samples also show continuous evolution of amorphous-like denser microstructure with increase in SiO{sub 2} content in the films. Hence incorporation of SiO{sub 2} in the Gd{sub 2}O{sub 3} matrix, results in a continuous change in oxygen coordination yielding a change in the Gd-O bond length and also results in a continuous increase in amorphousness and a smoother morphology of the samples and, unlike the HfO{sub 2}-SiO{sub 2} system, does not show any maximum for a particular SiO{sub 2} concentration.

36 MATERIALS SCIENCE↗

Electrical and chemical characteristics of probe-induced two-dimensional SiO{sub x} protrusion layers

Three two-dimensional SiO{sub x} (x {identical_to} O/Si content ratio and x > 2) protrusion layers of {approx}0.5, {approx}4, and {approx}6 nm high were induced on a native SiO{sub 2} layer by atomic force microscopy (AFM) probes. X-ray photoemission spectroscopy (XPS) was used to reveal the elemental quantity of the photoelectrons, Si 2p core-levels, and Si oxidation states in the three SiO{sub x} protrusion layers and native SiO{sub 2} layer. Pt-coated conductive AFM probes were also exploited to acquire the rectifying current-voltage (IV) characteristics of the three SiO{sub x} protrusion layers and the native SiO{sub 2} layer, indicating all the three SiO{sub x} protrusion layers to be good Schottky diodes.

36 MATERIALS SCIENCE↗

Microscopic mechanisms of graphene electrolytic delamination from metal substrates

In this paper, hydrogen bubbling delamination of graphene (Gr) from copper using a strong electrolyte (KOH) water solution was performed, focusing on the effect of the KOH concentration (C{sub KOH}) on the Gr delamination rate. A factor of ∼10 decrease in the time required for the complete Gr delamination from Cu cathodes with the same geometry was found increasing C{sub KOH} from ∼0.05 M to ∼0.60 M. After transfer of the separated Gr membranes to SiO{sub 2} substrates by a highly reproducible thermo-compression printing method, an accurate atomic force microscopy investigation of the changes in Gr morphology as a function of C{sub KOH} was performed. Supported by these analyses, a microscopic model of the delamination process has been proposed, where a key role is played by graphene wrinkles acting as nucleation sites for H{sub 2} bubbles at the cathode perimeter. With this approach, the H{sub 2} supersaturation generated at the electrode for different electrolyte concentrations was estimated and the inverse dependence of t{sub d} on C{sub KOH} was quantitatively explained. Although developed in the case of Cu, this analysis is generally valid and can be applied to describe the electrolytic delamination of graphene from several metal substrates.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

In situ multimodal imaging for nanoscale visualization of tribofilm formation

A third of the energy from fuel combustion in passenger car gasoline engines is lost due to friction. Carefully designed engine lubricants can recover some of these losses by reducing friction and wear by forming a nanometer-scale chemico-physico tribofilm between surfaces. Accordingly, attention has focused on developing oil formulations that form low-friction tribofilms. However, analyses of resultant tribofilms are typically conducted after tribo-tests with conventional characterization tools and do not offer insights into tribofilm formation and evolution, precluding information critical to tuning tribofilm properties. In this work, we developed a unique multimodal methodology based on Atomic Force Microscopy (AFM) with local probe heating for in situ tribological studies that activates friction modifiers and simultaneously captures the evolution of friction and surface roughness, with nanometer resolution. As a platform to demonstrate the ability of this methodology to visualize dynamics of tribofilm formation in situ, we apply it to molybdenum-based friction modifiers to distinguish key factors in their functionality and correlate nanoscale AFM and Friction Force Microscopy data to bench tribo-tests used in the industry. To decode the formation mechanisms observed in situ and underlying chemistry of tribofilms, we performed ab initio Molecular Dynamics (AIMD) simulations at comparable conditions. AIMD simulations confirmed both nanoscale and bench tribo-test results and showed deviations in molecular organization in tribofilms that are formed from different molybdenum-based friction modifiers that corroborates with surface functionality. With this innovative methodology, we demonstrate proof-of-principle in situ formation of molybdenum-based tribofilms directly on steel surfaces that could be applied generally to studying tribofilm formation.

36 MATERIALS SCIENCE↗

Crystallization study of amorphous sputtered NiTi bi-layer thin film

The crystallization of Ni-rich/NiTiCu bi-layer thin film deposited by magnetron sputtering from two separate alloy targets was investigated. To achieve the shape memory effect, the NiTi thin films deposited at room temperature with amorphous structure were annealed at 773 K for 15, 30, and 60 min for crystallization. Characterization of the films was carried out by differential scanning calorimetry to indicate the crystallization temperature, grazing incidence X-ray diffraction to identify the phase structures, atomic force microscopy to evaluate surface morphology, scanning transmission electron microscopy to study the cross section of the thin films. The results show that the structure of the annealed thin films strongly depends on the temperature and time of the annealing. Crystalline grains nucleated first at the surface and then grew inward to form columnar grains. Furthermore, the crystallization behavior was markedly affected by composition variations. - Highlights: • A developed bi-layer Ni45TiCu5/Ni50.8Ti was deposited on Si substrate and crystallized. • During crystallization, The Ni{sub 45}TiCu{sub 5} layer is thermally less stable than the Ni-rich layer. • The activation energy is 302 and 464 kJ/mol for Cu-rich and Ni-rich layer in bi-layer, respectively.

36 MATERIALS SCIENCE↗

Unraveling the Mechanism of Nanoscale Mechanical Reinforcement in Glassy Polymer Nanocomposites

The mechanical reinforcement of polymer nanocomposites (PNCs) above the glass transition temperature, T g , has been extensively researched. However, not much is known about the origin of this effect below T g . In this paper, we unravel the mechanism of PNC reinforcement within the glassy state by directly probing nanoscale mechanical properties with atomic force microscopy and macroscopic properties with Brillouin light scattering. Our results unambiguously show that the "glassy" Young's modulus in the interfacial polymer layer of PNCs is two-times higher than in the bulk polymer, which results in significant reinforcement below T g . We ascribe this phenomenon to a high stretching of the chains within the interfacial layer. Since the interfacial chain packing is essentially temperature independent, these findings provide a new insight into the mechanical reinforcement of PNCs also above T g .

36 MATERIALS SCIENCE↗

Atomic layer deposition of cerium oxide for potential use in diesel soot combustion

The particulate soot emission from diesel motors has a severe impact on the environment and people's health. The use of catalytic convertors is one of the ways to minimize the emission and decrease the hazard level. In this paper, the activity of cerium oxide for catalytic combustion of diesel soot was studied. Thin films of cerium dioxide were synthesized by atomic layer deposition using tetrakis(2,2,6,6-tetramethyl-3,5-heptanedionato)cerium [Ce(thd){sub 4}] and ozone as precursors. The characteristics of the films were studied as a function of deposition conditions within the reaction temperature range of 180–350 °C. Thickness, crystallinity, elemental composition, and morphology of the CeO{sub 2} films deposited on Si (100) were characterized by ellipsometry, x-ray diffraction, x-ray photoelectron spectroscopy, atomic force microscopy, and field emission scanning electron microscopy, respectively. The growth rate of CeO{sub 2} was observed to be 0.30 Å/cycle at temperatures up to 250 °C with a slight increase to 0.37 Å/cycle at 300 °C. The effect of CeO{sub 2} films grown on stainless steel foil supports on soot combustion was measured with annealing tests. Based on the analysis of these, in catalytic applications, CeO{sub 2} has been shown to be effective in lowering the soot combustion temperature from 600 °C for the uncoated substrates to 370 °C for the CeO{sub 2} coated ones. It was found that the higher deposition temperatures had a positive effect on the catalyst performance.

36 MATERIALS SCIENCE↗

On the Processes of the Self-Assembly of CdS Nanocrystal Arrays Formed by the Langmuir–Blodgett Technique

The morphology of CdS nanocrystal arrays self-assembled during the evaporation of a behenic-acid organic matrix on a wetted substrate surface is studied by atomic force microscopy. The dependence of the morphology of nanocrystal arrays on the initial matrix surface is studied. The morphology of nanocrystal arrays noticeably changes from small fractal arrays to a porous submonolayer with an increase in the nanocrystal density. The nature of attractive forces between nanocrystals which prevents their reversible adhesion and ensures their comparatively high mobility in the array composition is proposed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Laser ablation synthesis of silver nanoparticles in water and dependence on laser nature

Silver nanoparticles have been synthesized by a one step, easy, fast and green method. The nanoparticles were prepared in de-ionized water by laser ablation method using two lasers, a continuous wave (CW) diode laser and a pulsed Nd:YAG laser. The purpose of the experiment is to compare the role of nature of the laser for production of better NPs. The prepared silver nanoparticles were characterized for their, structural, physical and optical properties. The structural properties of the synthesized nanoparticles were characterized by X-ray Diffraction and the nanoparticles were found to be crystalline. The physical properties were analyzed by Atomic Force Microscopy which confirmed spherical and nanometer sized nanoparticles. The average size was 20 nm and 9 nm for continuous and pulsed laser respectively. The optical properties were analyzed by UV–Visible spectroscopy where band gap energy was investigated and increase in band gap energy as compared to bulk was observed. The green nature of laser ablation method, surface chemistry and chemical contamination of the surface of prepared nanoparticles were analyzed by Fourier Transform Infrared Spectroscopy. The thermal conductivity of the nanoparticles colloidal solutions (nanofluids) was calculated and an enhancement of 16% and 27% was observed for CW and pulsed laser prepared nanofluids respectively as compared to base liquid (de-ionized water).

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Synthesis, properties, and antianemic activity of new metal complexes of sodium pectinate with iron and calcium

A new water-soluble complex based on sodium pectinate with iron and calcium (P-NaFeCa) was synthesized. The regularities of the complexation of sodium pectinate (with a 35% content of COONa groups) with biogenic metals Ca and Fe were studied. The content of macro- and microelements was determined by atomic emission spectrometry; the product was identified by IR spectroscopy. Using atomic force microscopy, it was found that the average particle size of P-NaFeCa is ~170 nm. The efficiency of P-NaFeCa (per os) was studied for the first time in animals with hemolytic anemia modeled by administration of phenylhydrazine. It was experimentally shown that in vivo P-NaCaFe at a dose of 60 mg kg{sup –1} containing 50% of the recommended therapeutic dose of iron helps to recover the number of erythrocytes and mean concentration hemoglobin in erythrocyte, which indicates the efficiency of P-NaCaFe as an agent restoring the blood parameters after exposure to hemolytic poisons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of surface oxidation on the nm-scale wear behavior of a metallic glass

Metallic glasses are good candidates for applications in micromechanical systems. With size reduction of mechanical components into the micrometer and submicrometer range, the native surface oxide layer starts playing an important role in contact mechanical applications of metallic glasses. We use atomic force microscopy to investigate the wear behavior of the Ni{sub 62}Nb{sub 38} metallic glass with a native oxide layer and with an oxide grown after annealing in air. After the annealing, the wear rate is found to have significantly decreased. Also the dependency of the specific wear on the velocity is found to be linear in the case of the as spun sample while it follows a power law in the case of the sample annealed in air. We discuss these results in relation to the friction behavior and properties of the surface oxide layer obtained on the same alloy.

36 MATERIALS SCIENCE↗