Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transportation Data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Development and application of ride-quality criteria

A program for the development of ride-quality vibration criteria applicable to the design and evaluation of air and surface transportation systems is described. Consideration is given to the magnitude of vehicle vibration experienced by the passenger, the frequency of vibration, the direction of vibration, and the influence of seat dynamics on passenger response. Comparative vibration measurements are presented for a variety of air and surface transportation systems. In addition, simulator data on seat dynamics and passenger response are presented. Results suggest the relative merits of various physical descriptors and measurement locations for characterizing the vibration in terms suitable for the design and/or evaluation of transportation systems.

Stephens, D. G.↗

Shuttle flight pressure instrumentation: Experience and lessons for the future

Flight data obtained from the Space Transportation System orbiter entries are processed and analyzed to assess the accuracy and performance of the Development Flight Instrumentation (DFI) pressure measurement system. Selected pressure measurements are compared with available wind tunnel and computational data and are further used to perform air data analyses using the Shuttle Entry Air Data System (SEADS) computation technique. The results are compared to air data from other sources. These comparisons isolate and demonstrate the effects of the various limitations of the DFI pressure measurement system. The effects of these limitations on orbiter performance analyses are addressed, and instrumentation modifications are recommended to improve the accuracy of similar fight data systems in the future.

Siemers, P. M., III↗

The Remote Sensing of Mineral Aerosols and Their Impact on Phytoplankton Productivity using Sea WiFS

The main objective of this proposal was to use SeaWiFs data to study the relationship between aerosols found in aeollan dust and photosynthesis of phytoplankton in open ocean surface waters. This project was a collaborative effort between myself and Dr. Neil Tindale at Texas A&M University and followed on our earlier funded proposal which had been designed as a proof-of-concept study to determine if ocean color sensors such as the Coastal Zone Color Scanner (CZCS) could be used to detect and map large-scale mineral aerosol plumes. Despite the large spatial and temporal gaps inherent in the CZCS data coverage, our results from this initial study indicated that an ocean color sensor could indeed be used to detect aerosols. These encouraging results led us to propose in this proposal the use of SeaWiFS data to study mineral aerosol transport and its impact on phytoplankton production. This proposal orignally intended to make use of SeaWiFS images, but as the launch delay of SeaWiFS dragged on, we had to make do with other satellite data sets. Thus, the focus of this proposal became the CSCS image archive instead. I detail my results and accomplishments with this data set.

Stegmann, Petra M.↗

A Verification of Flux Sensitivity Estimates Using the MCNP Tally Perturbation Tool

Nuclear data is commonly used in applications such as nuclear nonproliferation, safeguards, and criticality safety. More specifically, nuclear data is used in predictive simulation codes like the Monte-Carlo N-Particle (MCNP ® ) transport code, Serpent, and similar radiation transport codes. The improvement of nuclear data enables more precise and accurate simulations, which result in higher fidelity designs and reduced operational/procedural costs. Therefore, the improvement of nuclear data is of paramount importance across the nuclear community. Nuclear data is improved and validated through integral benchmark experiments. The design of benchmark experiments is an extensive process; therefore, these experiments are often optimized on multiple characteristics, including sensitivity to the nuclear data, during the design process. Sensitivity is a measure of how much a quantity changes due to changes in independent variables such as experimental configuration. An experimental design that has a larger sensitivity to the nuclear data of interest will have a larger impact on the accuracy and precision of the validated data. Past integral benchmark experiments have primarily used the effective multiplication factor ($k_{eff}$) as the predominant measured quantity; however, experiments designed with other quantities in mind would be able to optimize on validating different areas of the nuclear data. A primary goal of the EUCLID project is to design, constrain, and reduce compensating errors in experiments focused on quantities other than $k_{eff}$ to better validate nuclear data across the board. Currently, there is a capability in MCNP to easily calculate the sensitivity of $k_{eff}$ to specific nuclear data of numerous reactions types and isotopes (KSEN card); however, the sensitivity of other quantities must be estimated in more strenuous manners. For example, the perturbation feature (PERT card) of MCNP can be used to estimate first-order sensitivities of some response in fixed source simulations. A recent announcement revealed that the first- and second-order perturbation features in previous releases of MCNP contained a bug. It was identified that particles were being scored into the wrong energy bin. The bug is in the most recent public release (MCNP6.2); however, a patch has been added to the most up to date version (MCNP6.2.2) that has not been released publicly. A direct comparison of the PERT card results for an F4 (neutron flux averaged over a cell) tally before and after the patch are shown in figure 1. All simulations used in the sensitivity estimates in this report were performed with MCNP6.2.2. This work verifies the patched MCNP perturbation tool by comparing first order sensitivities made using the PERT card to estimates made using manual perturbation of the compact ENDF (ACE) files.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

A Client/Server Architecture for Supporting Science Data Using EPICS Version 4

The Phase 1 grant that serves as a precursor to this proposal, prototyped complex storage techniques for high speed structured data that is being produced in accelerator diagnostics and beam line experiments. It demonstrates the technologies that can be used to archive and retrieve complex data structures and provide the performance required by our new accelerators, instrumentations, and detectors. Phase 2 is proposed to develop a high-performance platform for data acquisition and analysis to provide physicists and operators a better understanding of the beam dynamics. This proposal includes developing a platform for reading 109 MHz data at 10 KHz rates through a multicore front end processor, archiving the data to an archive repository that is then indexed for fast retrieval. The data is then retrieved from this data archive, integrated with the scalar data, to provide data sets to client applications for analysis, use in feedback, and to aid in identifying problem with the instrumentation, plant, beam steering, or model. This development is built on EPICS version 4 , which is being successfully deployed to implement physics applications. Through prior SBIR grants, EPICS version 4 has a solid communication protocol for middle layer services (PVAccess), structured data representation and methods for efficient transportation and access (PVData), an operational hierarchical record environment (JAVA IOC), and prototypes for standard structured data (Normative Types). This work was further developed through project funding to successfully deploy the first service based physics application environment with demonstrated services that provide arbitrary object views, save sets, model, lattice, and unit conversion. Thin client physics applications have been developed in Python that implement quad centering, orbit display, bump control, and slow orbit feedback. This service based architecture has provided a very modular and robust environment that enables commissioning teams to rapidly develop and deploy small scripts that build on powerful services. These services are all built on relational database data stores and scalar data. The work proposed herein, builds on these previous successes to provide data acquisition of high speed data for online analysis clients.

43 PARTICLE ACCELERATORS↗

Development of a Physical-Topological Model for the Response of a High-Power Vertical DMOS Transistor to the Effect of Pulsed Gamma-Radiation

A method for developing models of semiconductor devices with two-dimensional nonuniform concentration profiles of donors and acceptors in working regions of a semiconductor device structure is for the first time proposed based on a complex of physical-topological modeling of charge carrier transport and process simulation of the forming processes of the device structure. The application of process simulation is due to the need to correctly define the parameters of the semiconductor device structure, which are used as initial data to calculate the electron transport according to the physical-topological model. The parameters of production processes of ion implantation, diffusion, and lithography, which were refined during process simulation, are determined for a high-power metal—oxide—semiconductor (MOS) transistor forming by the double diffusion method in accordance with known electrical characteristics and measured geometrical sizes of the structure. This results in two-dimensional distribution profiles of donors and acceptors in p–n junctions necessary to calculate the transistor breakdown under the effect of pulsed γ radiation. Breakdown processes are modeled with the help of the physical-topological model based on the Poisson and continuity equations as well as expressions for the diffusion and drift current densities in the transistor. Accounting for carriers formed at the instant of γ irradiation is implemented by the introduction of the dependence of the generation coefficient of electron–hole pairs on the radiation-dose power. The results of calculations correlate well with the experimental data, which makes it possible to give a conclusion regarding the adequacy of the proposed complex model.

36 MATERIALS SCIENCE↗

Electrical properties of n-type GaSb substrates and p-type GaSb buffer layers for InAs/InGaSb superlattice infrared detectors

Lightly doped n-type GaSb substrates with p-type GaSb buffer layers are the preferred templates for growth of InAs/InGaSb superlattices used in infrared detector applications because of relatively high infrared transmission and a close lattice match to the superlattices. We report here temperature dependent resistivity and Hall effect measurements of bare substrates and substrate-p-type buffer layer structures grown by molecular beam epitaxy. Multicarrier analysis of the resistivity and Hall coefficient data demonstrate that high temperature transport in the substrates is due to conduction in both the high mobility zone center Γ band and the low mobility off-center L band. High overall mobility values indicate the absence of close compensation and that improved infrared and transport properties were achieved by a reduction in intrinsic acceptor concentration. Standard transport measurements of the undoped buffer layers show p-type conduction up to 300 K indicating electrical isolation of the buffer layer from the lightly n-type GaSb substrate. However, the highest temperature data indicate the early stages of the expected p to n type conversion which leads to apparent anomalously high carrier concentrations and lower than expected mobilities. Data at 77 K indicate very high quality buffer layers.

36 MATERIALS SCIENCE↗

Airframe noise component interaction studies

Acoustic wind tunnel tests were conducted of a two-dimensional wing section with removable high-lift leading and trailing edge devices and a removeable two-wheel landing gear with open cavity. An array of far field conventional microphones and an acoustic mirror directional microphone were utilized to determine far field spectrum levels and noise source distribution. Data were obtained for the wing with components deployed separately and in various combinations. The basic wing model had 0.305 m (1.00 ft) chord, which is roughly 1/10 scale for a one-hundred passenger transport airplane. Most of the data were obtained at 70.7 and 100 m/sec (232 and 328 ft/sec) airspeeds, which bracket the range of practical approach speeds for such aircraft. Data were obtained at frequence to 40 kHz so that, when scaled to s typical full-airframe, the frequency region which strongly influences preceived noise level would be included.

Fink, M. R.↗

Permeation of oxygen through high purity, large grain silver

The permeation of high purity, large grain Ag membranes by oxygen has been studied over the temperature range 400 to 800 C. The permeability was found to be quite linear and repeatable, but the magnitude was 3.2 times smaller than that determined by past research. Since previous investigators studied substantially less pure Ag and conducted experiments within much poorer vacuum environments (which indicates that their grain boundary density was much greater), the data presented here suggest oxygen transport through the membrane is primarily by grain boundary diffusion. The diffusivity measurements were found to exhibit two distinct linear regions, one above and one below a critical temperature of 630 C. The high-temperature data have an activation energy (11.1 kcal/mole) similar to that reported by others, but the low-temperature data have a higher activation energy (15.3 kcal/mole), which can be explained by impurity trapping in the grain boundaries. Vacuum desorption of the oxygen-saturated Ag was found to occur at a threshold of 630 C, which is consistent with the onset of increased mobility within the grain boundaries.

Outlaw, R. A.↗

Analysis of North Atlantic Aircraft Data on Oxygenated Intermediate Species Using an Adapted Regional Chemistry-Transport Model

Our study is on the interaction of nitrogen oxides with organics as they are exported from their complex sources in Eastern North America. Both urban and specific industrial emissions contribute the nitrogen of the C-H-O-N compounds that affect the global atmosphere, helping determine both ozone and the self-cleaning radical chemistry of the troposphere mediated by the OH radical. Different industrial sources, urban, and natural emissions contribute the organic C. Peroxyacetyl nitrate, CH3C(double bonds O)OONO2 is the most interesting compound for which we can measure the outflow to the full depth of the Atlantic troposphere. As we adapt the 3-d chemical model to describe outflow for specific periods with sufficient accuracy, we are analyzing some valuable information in the NARE-97 complete airborne dataset. (NARE: North Atlantic Regional Experiment). Ames researchers find that there are substantial puzzles in the ratios of PAN/NO2. Peroxy acetyl nitrate provides one of the major long-distance export pathways for active nitrogen from Eastern North America. It should be closely linked with NO, (defined as the sum NO + NO2) by simple thermal association and decomposition reactions, at least when the ambient temperature is substantially above 5 C.

Chatfield, Robert↗

Radiation Transport of Heliospheric Lyman-alpha from Combined Cassini and Voyager Data Sets

Heliospheric neutral hydrogen scatters solar Lyman-alpha radiation from the Sun with '27-day' intensity modulations observed near Earth due to the Sun's rotation combined with Earth's orbital motion. These modulations are increasingly damped in amplitude at larger distances from the Sun due to multiple scattering in the heliosphere, providing a diagnostic of the interplanetary neutral hydrogen density independent of instrument calibration. This paper presents Cassini data from 2003-2004 obtained downwind near Saturn at approximately 10 AU that at times show undamped '27-day' waves in good agreement with the single-scattering models of Pryor et al., 1992. Simultaneous Voyager 1 data from 2003- 2004 obtained upwind at a distance of 88.8-92.6 AU from the Sun show waves damped by a factor of -0.21. The observed degree of damping is interpreted in terms of Monte Carlo multiple-scattering calculations (e.g., Keller et al., 1981) applied to two heliospheric hydrogen two-shock density distributions (discussed in Gangopadhyay et al., 2006) calculated in the frame of the Baranov-Malama model of the solar wind interaction with the two-component (neutral hydrogen and plasma) interstellar wind (Baranov and Malama 1993, Izmodenov et al., 2001, Baranov and Izmodenov, 2006). We conclude that multiple scattering is definitely occurring in the outer heliosphere. Both models compare favorably to the data, using heliospheric neutral H densities at the termination shock of 0.085 cm(exp -3) and 0.095 cm(exp -3). This work generally agrees with earlier discussions of Voyager data in Quemerais et al., 1996 showing the importance of multiple scattering but is based on Voyager data obtained at larger distances from the Sun (with larger damping) simultaneously with Cassini data obtained closer to the Sun.

Pryor, W.↗

Shared and Ownership Mobility Technologies in the US: Data Availability and Usage Trends

This report supports the vision for a more sustainable transportation future by summarizing and analyzing the latest data on new mobility technologies, including ridesharing, shared and privately owned bikes, e-bikes, and scooters that have emerged over the past two decades. Having access to accurate and current data that is representative of new mobility systems and individual usage of these systems across different parts of the country is critical for researchers, city and regional planning professionals, and current and potential industry technology developers to better understand and forecast usage trends both nationwide as well as across different existing and potential future markets across the country. Building on the previous study published in 2022, this report incorporates the latest available market and usage data on new mobility technologies and compares usage by Chicago and New York City demographic characteristics. Moreover, this report includes recent developments and insights on privately owned micromobility technologies. Our analysis found that more downtown areas in Chicago show high per capita usage for all three modes than in the previous study, likely due to the full launch of shared e-scooter systems citywide in 2022. Notably, the majority of high shared mobility usage is concentrated in high-income, densely populated downtown areas in Chicago, which also have good public transit access. In contrast, TNC and bikeshare usage hotspots in central Manhattan are more widely distributed, though also appear to be shaped by the geography of the public transit system. Analysis of privately owned micromobility shows that the greatest energy savings occurred when e-bikes replaced single-occupancy vehicle (SOV) trips (i.e., gasoline-powered cars driven alone). Based on the literature review and analysis results, we also make recommendations for supporting the development of both shared and privately owned micromobility programs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Multigroup Neutron Cross Section Generation for the SCEPTRE Code

Multigroup neutron cross sections were generated for the deterministic radiation transport code SCEPTRE. ENDF/B-VII.1 nuclear data files were downloaded from Los Alamos National Laboratory (LANL), processed with the LANL cross-section preparation code NJOY-2012, and post-processed to produce a SCEPTRE-formatted cross section file. A simple radiation transport problem was used to compare results calculated with MCNP, a continuous-energy radiation transport code from LANL, to results calculated with SCEPTRE using the NJOY-2012-produced multigroup cross sections. This problem was used to debug the python scripts used to post-process the NJOY-2012 output and to assess the accuracy of the multigroup cross sections. These comparisons demonstrate that the multigroup cross sections generated in this work are accurate for most elements but yielded inaccurate results for several common transition metals. This discrepancy appears to result from poor treatment of the resolved resonance region of the continuous-energy cross sections. Further work is recommended to investigate alternative methods to treat these resonances with NJOY-2012.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

CIRFT Data Update and Data Analyses for Spent Nuclear Fuel Vibration Reliability Study

The objective of this research is to collect experimental data on spent nuclear fuel (SNF) from pressurized water reactors (PWRs), including the H. B. Robinson Nuclear Power Station (HBR), Catawba Nuclear Station, North Anna Nuclear Power Station (NA), and the Limerick Nuclear Power Station (LMK) boiling water reactor (BWR). Data will be collected under simulated transportation environments using the cyclic integrated reversible-bending fatigue tester (CIRFT), an enabling hot-cell testing technology developed at Oak Ridge National Laboratory (ORNL). These data will be used to support ongoing SNF modeling activities and to address regulatory issues associated with SNF transport.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ion temperature troughs and interhemispheric transport observed in the equatorial ionosphere

Ion temperature and ion drift velocity data from Atmosphere Explorer D have verified the existence of interhemispheric plasma transport and ion temperature troughs in the topside equatorial ionosphere. The data were taken during solar minimum conditions at night where the exospheric temperature was typically 700 K and the O(+)-H(+) transition height was 520 km. Large field-aligned ion velocities were observed above about 700 km, where the H(+)/O(+) number density ratio was about 3. Model calculations have shown that the ion temperature decrease is produced by quasi-adiabatic expansion of the plasma, but the expansion cooling mechanism is less efficient at solar minimum than at solar maximum owing to the lower O(+)-H(+) transition height. Ion temperature troughs greater than 400 K were not observed even when the field-aligned ion velocity was greater than 700 m/s. Most of the expansion occurs below the transition height, and during sunspot minimum, thermal coupling to the neutral atmosphere is much more effective in quenching the cooling which the field-aligned transport tends to produce.

Heelis, R. A.↗

A parametric analysis of transport aircraft system weights and costs

In determining unit and operating costs for advanced aircraft, it has been found that by having first-order weight and performance approximations for the aircraft systems and structural components, a step increase in cost prediction accuracy results. This paper presents first-order approximation equations for these systems and components. These equations were developed from data for most current jet transports, and they have been ordered to use a minimum number of performance parameters such as aircraft style, number of passengers, empty and gross weight, cargo load, and operating range. A NASA Ames Research Center aircraft cost program has been used to compare calculated and actual weights for the same aircraft. Good aircraft cost correlation is shown to exist between calculated first-order and actual aircraft weight data.

Anderson, J. L.↗

AXAF FITS standard for ray trace interchange

A standard data format for the archival and transport of x-ray events generated by ray trace models is described. Upon review and acceptance by the Advanced X-ray Astrophysics Facility (AXAF) Software Systems Working Group (SSWG), this standard shall become the official AXAF data format for ray trace events. The Flexible Image Transport System (FITS) is well suited for the purposes of the standard and was selected to be the basis of the standard. FITS is both flexible and efficient and is also widely used within the astronomical community for storage and transfer of data. In addition, software to read and write FITS format files are widely available. In selecting quantities to be included within the ray trace standard, the AXAF Mission Support team, Science Instruments team, and the other contractor teams were surveyed. From the results of this survey, the following requirements were established: (1) for the scientific needs, each photon should have associated with it: position, direction, energy, and statistical weight; the standard must also accommodate path length (relative phase), and polarization. (2) a unique photon identifier is necessary for bookkeeping purposes; (3) a log of individuals, organizations, and software packages that have modified the data must be maintained in order to create an audit trail; (4) a mechanism for extensions to the basic kernel should be provided; and (5) the ray trace standard should integrate with future AXAF data product standards.

Hsieh, Paul F.↗