Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Target”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

HIGH POWER BEAM DUMP AND TARGET / ACCELERATOR INTERFACE PROCEDURES

Satisfying operational procedures and limits for the beam target interface is a critical concern for high power operation at spallation neutron sources. At the Oak Ridge Spallation Neutron Source (SNS) a number of protective measures are instituted to ensure that the beam position, beam size and peak intensity are within acceptable limits at the target and high power Ring Injection Dump (RID). The high power beam dump typically handles up to 50 100 kW of beam power and its setup is complicated by the fact that there are two separate beam components simultaneously directed to the dump. The beam on target is typically in the 800-1000 kW average power level, delivered in sub- s 60 Hz pulses. Setup techniques using beam measurements to quantify the beam parameters at the target and dump will be described. However, not all the instrumentation used for the setup and initial qualification is available during high power operation. Additional techniques are used to monitor the beam during high power operation to ensure the setup conditions are maintained, and these are also described.

Blokland, Willem↗

Enhancing proton acceleration by using composite targets

Efficient laser ion acceleration requires high laser intensities, which can only be obtained by tightly focusing laser radiation. In the radiation pressure acceleration regime, where the tightly focused laser driver leads to the appearance of the fundamental limit for the maximum attainable ion energy, this limit corresponds to the laser pulse group velocity as well as to another limit connected with the transverse expansion of the accelerated foil and consequent onset of the foil transparency. These limits can be relaxed by using composite targets, consisting of a thin foil followed by a near critical density slab. Such targets provide guiding of a laser pulse inside a self-generated channel and background electrons, being snowplowed by the pulse, compensate for the transverse expansion. The use of composite targets results in a significant increase in maximum ion energy, compared to a single foil target case.

PACS numbers: 52.25.Os, 52.38.Kd, 52.27.Ny↗

Search for Hidden Sector and Dark Matter Particles Produced at Fermilab's NuMI Target

In the long tradition of exotic searches at fixed-target experiments, we plan to use the NuMI beam-target and the NOvA Near Detector to observe potential signatures of Hidden Sector or Dark Matter particles, either directly produced within the target or through theoretically postulated mediators. Expecting mostly scattering events on electrons or nucleons as their signatures, an example of a mediator generated scalar dark matter particles is used to discuss the target production profile of a dark matter beam. This channel explores the capabilities of the detector to observe neutral-current events from electron-neutrino scattering interactions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Protocells and their use for targeted delivery of multicomponent cargos to cancer cells

Various embodiments provide materials and methods for synthesizing protocells for use in targeted delivery of cargo components to cancer cells. In one embodiment, the lipid bilayer can be fused to the porous particle core to form a protocell. The lipid bilayer can be modified with targeting ligands or other ligands to achieve targeted delivery of cargo components that are loaded within the protocell to a target cell, e.g., a type of cancer. Shielding materials can be conjugated to the surface of the lipid bilayer to reduce undesired non-specific binding.

59 BASIC BIOLOGICAL SCIENCES↗

Porous nanoparticle-supported lipid bilayers (protocells) for targeted delivery and methods of using same

The present invention is directed to protocells for specific targeting of hepatocellular and other cancer cells which comprise a nanoporous silica core with a supported lipid bilayer; at least one agent which facilitates cancer cell death (such as a traditional small molecule, a macromolecular cargo (e.g. siRNA or a protein toxin such as ricin toxin A-chain or diphtheria toxin A-chain) and/or a histone-packaged plasmid DNA disposed within the nanoporous silica core (preferably supercoiled in order to more efficiently package the DNA into protocells) which is optionally modified with a nuclear localization sequence to assist in localizing protocells within the nucleus of the cancer cell and the ability to express peptides involved in therapy (apoptosis/cell death) of the cancer cell or as a reporter, a targeting peptide which targets cancer cells in tissue to be treated such that binding of the protocell to the targeted cells is specific and enhanced and a fusogenic peptide that promotes endosomal escape of protocells and encapsulated DNA. Protocells according to the present invention may be used to treat cancer, especially including hepatocellular (liver) cancer using novel binding peptides (c-MET peptides) which selectively bind to hepatocellular tissue or to function in diagnosis of cancer, including cancer treatment and drug discovery.

59 BASIC BIOLOGICAL SCIENCES↗

The DESI Experiment Part I: Science,Targeting, and Survey Design

DESI (Dark Energy Spectroscopic Instrument) is a Stage IV ground-based dark energy experiment that will study baryon acoustic oscillations (BAO) and the growth of structure through redshift-space distortions with a wide-area galaxy and quasar redshift survey. To trace the underlying dark matter distribution, spectroscopic targets will be selected in four classes from imaging data. We will measure luminous red galaxies up to $z=1.0$. To probe the Universe out to even higher redshift, DESI will target bright [O II] emission line galaxies up to $z=1.7$. Quasars will be targeted both as direct tracers of the underlying dark matter distribution and, at higher redshifts ($ 2.1 < z < 3.5$), for the Ly-$\alpha$ forest absorption features in their spectra, which will be used to trace the distribution of neutral hydrogen. When moonlight prevents efficient observations of the faint targets of the baseline survey, DESI will conduct a magnitude-limited Bright Galaxy Survey comprising approximately 10 million galaxies with a median $z\approx 0.2$. In total, more than 30 million galaxy and quasar redshifts will be obtained to measure the BAO feature and determine the matter power spectrum, including redshift space distortions.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Amplification of biological targets via on-chip culture for biosensing

The present invention, in part, relates to methods and apparatuses for on-chip amplification and/or detection of various targets, including biological targets and any amplifiable targets. In some examples, the microculture apparatus includes a single-use, normally-closed fluidic valve that is initially maintained in the closed position by a valve element bonded to an adhesive coating. The valve is opened using a magnetic force. The valve element includes a magnetic material or metal. Such apparatuses and methods are useful for in-field or real-time detection of targets, especially in limited resource settings.

47 OTHER INSTRUMENTATION↗

Moving K-12 Zero Energy Schools to the Mainstream: Establishing Design Guidelines and Energy Targets: Preprint

K-12 school buildings are ideal candidates to lead the market shift from buildings that consume energy to buildings that produce as much renewable energy as they use, and there are now resources available to guide owners and project teams as they make that shift. Chief among them is the Advanced Energy Design Guide for K-12 School Buildings: Achieving Zero Energy (K-12 ZE AEDG). Starting with a feasibility study to prove that zero energy schools were possible, a committee of industry experts used extensive energy modeling to create a set of energy use intensity allowances for school buildings such that on-site renewable energy could meet the buildings' energy loads . These energy targets were compared with the energy use intensities of a limited number of schools that have achieved very high levels of energy performance. The allowances represent a 'zero energy ready' (rather than zero energy) school, because in many situations the ability to use on-site renewable sources is limited by utilities, policies, or economics. From these targets, the guidance for achieving a zero energy school was created and developed into the K-12 ZE AEDG, which covers the process of designing and building zero energy schools from the perspective of an owner and a project team. The K-12 ZE AEDG advocates setting an absolute energy target before design begins. The K-12 ZE AEDG also contains practical, cost-effective strategies for achieving the energy target and outreach approaches and disseminating these market-friendly strategies to design and school owner communities.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Amplification of biological targets via on-chip culture for biosensing

The present invention, in part, relates to methods and apparatuses for on-chip amplification and/or detection of various targets, including biological targets and any amplifiable targets. In some examples, the microculture apparatus includes a single-use, normally-closed fluidic valve that is initially maintained in the closed position by a valve element bonded to an adhesive coating. The valve is opened using a magnetic force. The valve element includes a magnetic material or metal. Such apparatuses and methods are useful for in-field or real-time detection of targets, especially in limited resource settings.

59 BASIC BIOLOGICAL SCIENCES↗

Application of compressed magnetic fields to the ignition and thermonuclear burn of inertial confinement fusion targets

Application of axial seed magnetic fields in the range 20-100 T that compress to greater than 10,000 T (100 MG) under typical NIF implosion conditions may significantly relax the conditions required for ignition and propagating burn in NIF ignition targets that are degraded by hydrodynamic instabilities. Such magnetic fields can: (a) permit the recovery of ignition, or at least significant alpha particle heating, in submarginal NIF targets that would otherwise fail because of adverse hydrodynamic instability growth, (b) permit the attainment of ignition in conventional cryogenic layered solid-DT targets redesigned to operate under reduced drive conditions, (c) permit the attainment of volumetric ignition in simpler, room-temperature single-shell DT gas capsules, and (d) ameliorate adverse hohlraum plasma conditions during laser drive and capsule compression. In general, an applied magnetic field should always improve the ignition condition for any NIF ignition target design.

47 OTHER INSTRUMENTATION↗

Lanthanum Bromide Detector System for Mu2e Stopping Target Monitor

The stopping target monitor (STM) in the Mu2e experiment is used to normalize the muon decay branching ratio in the Mu2e experiment, by estimating the number of muons that have been captured on the Mu2e nuclear target. The STM measures the distinctive muonic atomic transition lines and muonic nuclear excitations produced in the Aluminum Stopping Target of Mu2e. These signals must be disentangled in the presence of high rate Bremsstrahlung and other backgrounds produced in the target. An HPGe detector with fine energy resolution, ~0.1% will be employed but has limited count rate capability, ~20kcps. Time-to-Decision, that is the time to make an estimate of the experiments observed luminosity, is inversely proportional to the signal rate squared. For this reason the STM will also use a Lanthanum Bromide(LaBr3) detector, having ~2% energy resolution but capable of ~1 Mcps counting rate. This higher rate will allow not only an orthogonal verification of the HPGe luminosity measurements, but will also yield much finer luminosity measurements as a function of time because of its significantly higher counting rate capabilities. Geant4 simulations are presented comparing the performance of different sized, LaBr3 crystals. The results highly favor the use of the commercially available right circular cylindrical, 3x3-in. detector. Modifications to the STM design are discussed in order to take full advantage of the LaBr3 high rate and fast decision making capabilities. A preliminary design will be presented for a custom read-out system needed to fulfill these requirements.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Moving K-12 Zero Energy Schools to the Mainstream: Establishing Design Guidelines and Energy Targets

K-12 school buildings are ideal candidates to lead the market shift from buildings that consume energy to buildings that produce as much renewable energy as they use, and there are now resources available to guide owners and project teams as they make that shift. Chief among them is the Advanced Energy Design Guide for K-12 School Buildings: Achieving Zero Energy (K-12 ZE AEDG). Starting with a feasibility study to prove that zero energy schools were possible, a committee of industry experts used extensive energy modeling to create a set of energy use intensity allowances for school buildings such that on-site renewable energy could meet the buildings' energy loads . These energy targets were compared with the energy use intensities of a limited number of schools that have achieved very high levels of energy performance. The allowances represent a 'zero energy ready' (rather than zero energy) school, because in many situations the ability to use on-site renewable sources is limited by utilities, policies, or economics. From these targets, the guidance for achieving a zero energy school was created and developed into the K-12 ZE AEDG, which covers the process of designing and building zero energy schools from the perspective of an owner and a project team. The K-12 ZE AEDG advocates setting an absolute energy target before design begins. The K-12 ZE AEDG also contains practical, cost-effective strategies for achieving the energy target and outreach approaches and disseminating these market-friendly strategies to design and school owner communities.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

File transfers between machines without target CPU intervention

Techniques for transferring files between machines include creating a zero-length target file on non-volatile storage, truncating the file to a desired size, and allocating storage on the non-volatile storage for each block of the target file. The technique also includes determining a logical block address (LBA) for each location in the target file. The technique further includes sending a request to an input/output (I/O) node to transfer a source file to the non-volatile storage, where the request includes a mapping between the LBAs and file offsets. The technique includes opening the source file and a block device at the I/O node. The technique further includes reading each block from the source file and writing each block to the target file on the non-volatile storage utilizing the block device, and then closing the source file and the block device.

97 MATHEMATICS AND COMPUTING↗

Doses and fluxes in the proton-irradiated Big Target: A MARS15 analysis

This work is aimed at determination of secondary particle fluxes, prompt and residual doses as well as energy deposition in and around the Big Target, a 20-tonnes cylindrical target made of natural uranium with the lead core and a stainless-steel yoke, which is being considered to be irradiated by a 0.16-μA 600-MeV proton beam of the JINR Phasotron accelerator. The simulations were performed with the use of the MARS15 particle transport code employing the LAQGSM and CEM generators and based on the ENDFB-VIII neutron cross section library. The calculations for 12-hour, 100-hour, and 3-day irradiations with the aforementioned conditions indicate that temperature rise due to the beam does not require target cooling, the target can be safely handled soon after the end of irradiation, and its decommissioning is possible three years past the irradiation. Doses

43 PARTICLE ACCELERATORS↗

Moving Zero Energy Office Buildings to the Mainstream: Establishing Design Guidelines and Energy Targets: Preprint

Office buildings represent a significant portion of the commercial sector and are ideal candidates to lead the market towards achieving zero energy or zero energy ready buildings. The variety of sizes and uses for office buildings make them challenging to determine set design guidance that can be deployed across the market. A project committee for ASHRAE’s Zero Energy - Advanced Energy Design Guide (ZE-AEDG) for small and medium office buildings , comprised of members from five major national associations with market-pull in commercial buildings, created design guidance for achieving zero energy office buildings for new construction and major retrofit. This design guidance focuses on the process, providing a pathway for both office owners and design teams to achieve zero energy status. Energy use intensity targets range from 16 kBtu/ft²·yr to 36 kBtu/ft²·yr for the different climate zones were established such that office buildings can be “zero-ready,” that is, having low energy consumption that can easily be offset with renewables, preferably on-site. The design guidance was rooted in extensive energy modeling, as well as case studies of actual office buildings that have achieved high levels of energy performance and met zero energy or zero energy ready status. A unique aspect of the zero-energy guide is that it is not compared against a baseline but focuses on achieving an absolute target. The paper presents process of creating the targets, the selection of strategies to achieve the targets, and sample case studies that show how the cost-sensitive solutions are achievable for the design community. It also presents outreach strategies to deploy market achievable zero energy measures.

buildings↗

Modeling Needs for High Power Target

The next generation of high power targets will use more complex geometries, novel materials, and new concepts (like flowing granular materials); however, the current numerical approaches will not be sufficient to converge towards a reliable target design that satisfies the physical requirements. We will discuss what can be improved in the next 10 years in target modeling to support high power (MW class) targets.

43 PARTICLE ACCELERATORS↗

Muon Neutrino Charged Current Single Pion Production on Various Targets in the MINERvA Detector

Measurements of neutrino oscillation parameters at accelerator-based experiments require precise knowledge of neutrino interaction cross sections. A significant fraction of neutrino interactions observed in these experiments produce single charged pions. While single charged pion production has been measured on hydrocarbon and water, few precise measurements exist for heavier targets, and there are no high statistics measurements that directly compare pion production on different targets. This thesis measures differential cross sections of muon neutrino charged current single charged pion production with no other mesons in the final state in a neutrino beam with a mean energy of $\approx 6$ GeV. The pion production is studied on targets of scintillator, carbon, water, iron, and lead at MINERvA, a neutrino cross section experiment located in the NuMI beamline at Fermilab. These measured cross sections are differential in $\mu^-$ and $\pi^+$ kinematics. A strong suppression of low $Q^2 $ and an enhancement of low $T_\pi$ are observed relative to commonly used neutrino interaction models in both the light and heavy nuclear targets. Incorporation of these observed effects in future neutrino oscillation experiments will improve their ability to measure energy of neutrino interactions, and therefore measure the parameters governing neutrino oscillations.

Bercellie, Aaron↗

Muon neutrino charged current single pion production on various targets in the MINERvA detector

Measurements of neutrino oscillation parameters at accelerator-based experiments require precise knowledge of neutrino interaction cross sections. A significant fraction of neutrino interactions observed in these experiments produce single charged pions. While single charged pion production has been measured on hydrocarbon and water, few precise measurements exist for heavier targets, and there are no high statistics measurements that directly compare pion production on different targets. This thesis measures differential cross sections of muon neutrino charged current single charged pion production with no other mesons in the final state in a neutrinobeam with a mean energy of ≈ 6 GeV. The pion production is studied on targets of scintillator, carbon, water, iron, and lead at MINERvA, a neutrino cross section experiment located in the NuMI beamline at Fermilab. These measured cross sections are differential in μ - and π + kinematics. A strong suppression of low Q 2 and an enhancement of low π are observed relative to commonly used neutrino interaction models in both the light and heavy nuclear targets. Incorporation of these observed effects in future neutrino oscillation experiments will improve their ability to measure energy of neutrino interactions, and therefore measure the parameters governing neutrino oscillations.

Bercellie, Aaron↗