Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solubility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Synthesis and structural characterisation using Rietveld and pair distribution function analysis of layered mixed titaniumzirconium phosphates

Crystalline metal (IV) phosphates with variable zirconium-to-titanium molar ratios of general formula (Ti 1-x Zr x )(HPO 4 ) 2 • H 2 O have been prepared by precipitation of soluble salts of the metals with phosphoric acid and heating the amorphous solids in 12 M H 3 PO 4 in an autoclave. The new materials are structurally characterised by Rietveld analysis of synchrotron X-ray powder diffraction data and pair distribution function (PDF) analysis of high energy synchrotron X-ray total scattering data. A broad range of zirconium-titanium phosphate solid solutions were formed showing isomorphous substitution of titanium by zirconium in the α-titanium phosphate lattice and vice versa for titanium substitution into the α-zirconium phosphate lattice. In both cases the solubility is partial with the coexistence of two substituted phases observed in samples with nominal compositions between the solubility limits.

43 PARTICLE ACCELERATORS↗

B-site substitutions in LaNb{sub 1-x}M{sub x}O{sub 4-{delta}} materials in the search for potential proton conductors (M=Ga, Ge, Si, B, Ti, Zr, P, Al)

The solid solubilities of potential B-site dopants in LaNb{sub 1-x}M{sub x}O{sub 4-{delta},} materials, M=Ga, Ge, Si, Al, B, P, Zr or Ti, have been investigated in the search for possible novel proton conductors. In general, the solubility levels of these cations were found to be very low (x{<=}0.03). At the maximum value x=0.03, only compositions containing Ti, Ge, Ga and Si appeared pure at the limit of resolution of XRD. The literature phase diagram, La{sub 2}O{sub 3}-Nb{sub 2}O{sub 5}-ZrO{sub 2}, has been re-analysed for compositions of low Zr-content around the composition LaNbO{sub 4}. The electrical properties of phase pure Ti-doped compositions have been studied. Higher bulk and total conductivities were observed in wet than dry conditions, suggesting a significant protonic contribution to total conductivity. In wet conditions, the activation energy for bulk conductivity of LaNb{sub 0.98}Ti{sub 0.02}O{sub 4-{delta}} was found to be much higher than that of an A-site, Sr-doped material, Sr{sub 0.02}La{sub 0.98}NbO{sub 4-{delta},} of similar acceptor dopant concentration. The Sr-doped composition offered higher conductivities than the Ti-doped composition up to approximately 900{sup o}C. -- Graphical abstract: Comparison of total (open symbols) and bulk (closed symbols) conductivities measured in wet (p(H{sub 2}O){approx}0.026 atm.) nitrogen and oxygen atmospheres for LaNb{sub 0.98}Ti{sub 0.02}O{sub 4-{delta}} (LNT2O) and Sr{sub 0.02}La{sub 0.98}NbO{sub 4-{delta}} (S2LNO) materials. Display Omitted Research highlights: {yields} The article investigates solid solubilities of potential B-site dopants in the potential proton conductor LaNb{sub 1-x}M{sub x}O{sub 4-{delta},} {yields} The literature phase diagram, La{sub 2}O{sub 3}-Nb{sub 2}O{sub 5}-ZrO{sub 2}, has been corrected for compositions of low Zr-content around the composition LaNbO{sub 4}. {yields} The electrical properties of Ti-doped compositions have been assessed in wet and dry conditions. {yields} Comparison has been made between the electrical properties of B-site, Ti-doped, compositions and A-site, Sr-doped, compositions.

36 MATERIALS SCIENCE↗

Chromium incorporation into TiO{sub 2} at high pressure

Chromium incorporation into TiO{sub 2} up to 3 GPa at 1300 Degree-Sign C and 900 Degree-Sign C has been studied by XRD as well as TEM. A CaCl{sub 2} type TiO{sub 2} polymorph has been observed in the quenched samples from high pressure. Two different mechanisms of solubility occur in the recovered samples. Chromium replaces titanium on normal octahedral sites but it also occupies interstitial octahedral sites, especially in the samples recovered from higher pressures. Interstitial chromium is responsible for an orthorhombic distortion of the TiO{sub 2} rutile structure in the quenched samples and gives rise to a (1 1 0) twinned CaCl{sub 2}-structured polymorph. This phase is very likely the result of temperature quench at high pressure. The formation of this phase is directly related to the chromium content of the TiO{sub 2} grains. Chromium solubility in TiO{sub 2} increases with increasing the synthesis pressure. TiO{sub 2} is able to accommodate up to 15.3 wt% Cr{sub 2}O{sub 3} at 3 GPa and 1300 Degree-Sign C, compared to 5.7 wt% at atmospheric pressure at the same temperature. - Graphical abstract: Microstructure consisting of twins domains of recovered Cr-doped CaCl{sub 2} type TiO{sub 2} grains synthesised at high pressure. Highlights: Black-Right-Pointing-Pointer Chromium solubility in TiO{sub 2} increases at high pressure. Black-Right-Pointing-Pointer Chromium occupies substitutional and interstitial positions in the rutile structure. Black-Right-Pointing-Pointer Interstitial chromium causes a decrease of the rutile symmetry. Black-Right-Pointing-Pointer An orthorhombic CaCl{sub 2} type structure is observed in the quenched samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhanced thermoelectric performance in zinc substituted p-type filled skutterudites CeFe{sub 4-x}Zn{sub x}Sb{sub 12}

In this study, Zn-substituted polycrystalline skutterudites CeFe{sub 4-x}Zn{sub x}Sb{sub 12} (x=0, 0.05, 0.1, 0.2, 0.3) were successfully prepared by a traditional melting-annealing method. The solubility of Zn in Fe site is {approx}1.2%, exceeding which trace amount of ZnSb phase can be detected in the XRD. This ZnSb impurity phase, with size of several hundred nanometers for the sample with x=0.2 but showing surprisingly small size of {approx}10 nm for the sample with x=0.3, selectively distributes on the grain boundaries. In particular, the introduction of Zn in Fe site effectively improves the Seebeck coefficient in a manner of enhancement in hole effective mass, but it has negligible influence on both electrical and thermal conductivities though the hole concentration is increased. Consequently the corresponding improvement in power factor leads to an improved thermoelectric figure of merit (ZT) of 0.9 at 800 K for the sample with x=0.1, which is {approx}15% higher than that of Zn-free sample. This study demonstrates a favorable effect of Zn iso-substitution and opens a new strategy to improve the thermoelectric properties of p-type Fe-based skutterudites beyond the sole phonon engineering. - Graphical abstract: (a)-(c) ZnSb nanoinclusions emerge when Zn exceeds its solubility limit. (d), (e) The introduction of Zn boosts the Seebeck coefficient and thus enhances the ZT value. Highlights: Black-Right-Pointing-Pointer Zn is successfully employed to substitute Fe atom for the first time. Black-Right-Pointing-Pointer ZnSb nanoinclusions emerge when Zn exceeds its solubility limit {approx}0.12. Black-Right-Pointing-Pointer The introduction of Zn boosts the Seebeck coefficient and enhances the ZT value.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mo{sub x}Cu{sub 1-x}Sr{sub 2}YCu{sub 2}O{sub y} (0.3{<=}x{<=}1) revisited: Superconductivity, magnetism and the molybdenum oxidation state

A systematic study is reported on the range of stability of molybdenum substituted Sr-based 123 compounds with Mo-Sr-Y-Cu system, synthesized under ambient pressure. All materials crystallize in the space group: P4/mmm and the observed solubility limit of Mo is rather low in this structure because secondary phases start to form as soon as x>0.3 in nominal composition is reached. The antiferromagnetic property in all superconducting multiphase samples can be attributed to the secondary phase Y{sub 2}Cu{sub 2}O{sub 5}. The influence of oxygen annealing on the changes in electronic structure for the pure Mo{sub 0.3}Cu{sub 0.7}Sr{sub 2}YCu{sub 2}O{sub y} system associated with a non-superconductor to superconductor transition has been investigated by means of X-ray photoelectron spectroscopy, powder X-ray diffraction, magnetic susceptibility and specific-heat measurements. We unambiguously show the predominance of the Mo{sup 5+} state over the Mo{sup 6+} one on both as-synthesized and annealed phases; annealing under an oxygen atmosphere enhances both the Mo{sup 6+} and Cu{sup 2+} amounts. We suggest that the enhancement of Mo{sup 6+} under oxygen annealing is in close relation with the decrease in the O 2p{yields}Cu 3d charge-transfer energy resulting in superconducting properties. - Graphical abstract: A study on the ambient-pressure synthesis and the range of stability of complex perovskites in the system Y-Sr-Cu-Mo shows that the solubility limit of Mo is rather low in this structure ({approx}30%). Secondary phases (detected by XRD) start to form for x>0.3 in nominal composition. All materials crystallize in the space group: P4/mmm. Antiferromagnetism in all superconducting multiphase samples is attributed to the secondary phase Y{sub 2}Cu{sub 2}O{sub 5}. Pure Mo{sub 0.3}Cu{sub 0.7}Sr{sub 2}YCu{sub 2}O{sub y} studied by means of powder X-ray diffraction, magnetic susceptibility and specific-heat measurements. Changes in electronic structure for the pure Mo{sub 0.3}Cu{sub 0.7}Sr{sub 2}YCu{sub 2}O{sub y} system associated with a non-superconductor to superconductor transition have been investigated by means of X-ray photoelectron spectroscopy (XPS). Highlights: Black-Right-Pointing-Pointer Solubility limit of Mo is rather low in Mo{sub x}Cu{sub 1-x}Sr{sub 2}YCu{sub 2}O{sub y} (x{approx}0.3). Black-Right-Pointing-Pointer Antiferromagnetism and superconductivity do not coexist. Black-Right-Pointing-Pointer Pure Mo{sub 0.3}Cu{sub 0.7}Sr{sub 2}YCu{sub 2}O{sub y} (T{sub c} Almost-Equal-To 30 K) prepared and characterized. Black-Right-Pointing-Pointer XPS shows that Mo{sup 5+} predominates over Mo{sup 6+}. Black-Right-Pointing-Pointer Annealing under O{sub 2} enhances Mo{sup 6+} and Cu{sup 2+} states.

36 MATERIALS SCIENCE↗

Co-substitution at the Mn-site in YMnO{sub 3}: Structural stability and physical properties

Highlights: Black-Right-Pointing-Pointer Solid state synthesis of several series of hexagonal co-substituted YMn{sub 1-x}(M Prime ,M Double-Prime ){sub x}O{sub 3}. Black-Right-Pointing-Pointer Evidencing the critical parameters which govern the stabilization of the hexagonal phase. Black-Right-Pointing-Pointer Inducing a decrease of the antiferromagnetic ordering temperature by co-substitutions. -- Abstract: The YMnO{sub 3} oxide, crystallizing in the P6{sub 3}cm space group is one of the most studied multiferroic material. While these properties can be modified by substitutions at the Mn-site, the peculiar fivefold coordination appears to limit the M solubility range in YMn{sub 1-x}M{sub x}O{sub 3}. This motivated the preparation by solid state reaction of several series of co-substituted YMn{sub 1-x}(M Prime ,M Double-Prime ){sub x}O{sub 3}, which were studied using both powder X-ray diffraction and transmission electron microscopy. The cation pairs have been chosen for their ability to adopt a fivefold coordination similar to that of Mn{sup 3+} in YMnO{sub 3}, to keep a constant average trivalent oxidation state and to maintain an average cationic radius similar to that of Mn{sup 3+}. For YMn{sub 1-x}(Cu{sub 1/2}Ti{sub 1/2}){sub x}O{sub 3}, a complete solid solution is observed without cation ordering. For all other studied cation pairs, the solubility range is always reaching a minimum value of 25% for the Zn containing pairs (Zn{sub 2/3}V{sub 1/3} and Zn{sub 3/4}Mo{sub 1/4}), a maximum of 50% being reached for the Cu containing pairs (Cu{sub 2/3}V{sub 1/3}, Cu{sub 2/3}Nb{sub 1/3} and Cu{sub 3/4}W{sub 1/4}). Interestingly, the non-centrosymmetric P6{sub 3}cm space group is retained within the solubility range without generating cation ordering phenomena. These co-substitutions at the Mn{sup 3+} are found to induce a decrease of the antiferromagnetic ordering temperature, the T{sub N} variations being similar to the temperature decrease of the dielectric anomaly. Thus, these oxides are interesting candidates for the study of the multiferroic behavior of YMnO{sub 3} derivatives.

36 MATERIALS SCIENCE↗

Performance of Nitrile-Containing Anions in Task-Specific Ionic Liquids for Improved CO2/N2 Separation

This work explores the performance of a series of ionic liquids that incorporate a nitrile-containing anion paired to 1-alkyl-3-methylimidazolium cations in tailoring the selectivity and permeance of supported ionic liquid membranes for CO2/N2 separations. The permeance and selectivity of three ionic liquids, each with an increasing number of nitrile groups in the anion (i.e., two, three, and four), were measured using a non-steady-state permeation method. By predictably varying the molar volume and viscosity of the ionic liquids, we show that the solubility, selectivity, and permeance can be optimized for CO2/N2 separation through controlled introduction of the nitrile functionality into the anion. Of the three nitrile-based ionic liquids studied, 1-ethyl-3-methylimidazolium tetracyanoborate, [emim][B(CN)4], showed the highest permeance with a value of 2.55 10 9 mol/(m2 Pa s), a magnitude 30% higher than that of the popular ionic liquid [emim][Tf2N]. This same nitrile-bearing ionic liquid also exhibited a high CO2/N2 selectivity of approximately 53. Additionally, the carbon dioxide solubility for each ionic liquid was measured at room temperature with [emim][B(CN)4] again exhibiting the highest CO2 solubility. Results from our study of the nitrile-based ionic liquids can be rationalized in terms of regular solution theory wherein the selectivity and permeance of a given SILM system are largely determined by the molar volume and viscosity of the corresponding ionic liquid phase.

59 BASIC BIOLOGICAL SCIENCES↗

Ring Opened Heterocycles: Promising Ionic Liquids for Gas Separation and Capture

We report on a new class of highly fluid ionic liquids integrating a cation that resembles an opened imidazolium structure with two distinct anions, bis(trifluoromethylsulfonyl)imide, [Tf{sub 2}N], and a nitrile-containing anion, [C(CN)3]. These new ionic liquids show exceptional CO{sub 2} permeability values in liquid membrane gas separations with results that equal or exceed the Robeson upper bound. Moreover, these ionic liquids offer ideal CO{sub 2}/N{sub 2} selectivities competitive with the best results reported to date, exhibiting values that range from 28 to 45. The nitrile containing ionic liquid displayed the highest ideal CO{sub 2}/N{sub 2} selectivity with a value of 45 which primarily results from a reduction in the nitrogen permeability. In addition to permeability results, CO{sub 2} solubilities were also measured for the this new class of ionic liquids with values similar to the popular 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide. The CO{sub 2} solubility results were compared to predicted values obtained using both a modified regular solution theory and the quantum chemical Conductor-like Screening Model for Real Solvents (COSMO-RS) method. Agreement between predicted and measured solubility values is also discussed.

54 ENVIRONMENTAL SCIENCES↗

Scuffing initiation in metals sliding against copper under non-lubricated conditions

Metallic components in sliding contact are sometimes subjected to high-loads with little or no lubrication. Such starved conditions can lead to a phenomenon called scuffing. Various definitions exist for this term, but in the present case, three criteria were used to signal its onset: changes in friction, vibrations, and noise, coupled with surface examination. On this basis, scuffing initiation was determined for seven technically pure metals (Al, Mo, Nb, Ta, Ti, W, Cu) and stainless steel, all rubbing against Cu. A flat-ended pin-on-disk test configuration was used with normal loads of 1-3 N, and with step-wise increases in sliding speed from 0.16 to 2.56 m/s. Al was only weakly resistant to scuffing, presumably due to its solubility in Cu, its high ductility and its relatively low elastic modulus. Niobium provided satisfactory sliding behavior at low speeds and loads, presumably due to protective oxides; however, it scuffed at higher loads when the oxide broke through. Stainless steel, Mo, and Ta had higher friction coefficients than Al and Nb, presumably because the relatively high strengths of the former prevented severe wear even when their oxide films failed. Like Al, Ti scuffs on Cu, probably because of its high relative solubility; however, Ti's higher elastic modulus resists the more severe forms of surface damage than does Al. Of all the materials slid against Cu, W displayed the least scuffing, even under maximum speed and load. Tungsten's negligible solubility in Cu may have reduced its adhesion, and W's high elastic modulus resisted shear-deformation, even at high frictional heating. Self-mated Cu couple scuffed when the speed was increased. The oxides on the Cu surface serve as solid lubricant avoiding scuffing at lower speeds.

36 MATERIALS SCIENCE↗

Dissolution of Danazol Amorphous Solid Dispersions: Supersaturation and Phase Behavior as a Function of Drug Loading and Polymer Type

Amorphous solid dispersions (ASDs) are of great interest as enabling formulations because of their ability to increase the bioavailability of poorly soluble drugs. However, the dissolution of these formulations under nonsink dissolution conditions results in highly supersaturated drug solutions that can undergo different types of phase transitions. As such, the purpose of this study was to characterize the phase behavior of solutions resulting from the dissolution of model ASDs as well as the degree of supersaturation attained. Danazol was chosen as a poorly water-soluble model drug, and three polymers were used to form the dispersions: polyvinylpyrrolidone (PVP), hydroxypropylmethyl cellulose (HPMC), and hydroxypropylmethyl cellulose acetate succinate (HPMCAS). Dissolution studies were carried out under nonsink conditions, and solution phase behavior was characterized using several orthogonal techniques. It was found that liquid–liquid phase separation (LLPS) occurred following dissolution and prior to crystallization for most of the dispersions. Using flux measurements, it was further observed that the maximum attainable supersaturation following dissolution was equivalent to the amorphous solubility. The dissolution of the ASDs led to sustained supersaturation, the duration of which varied depending on the drug loading and the type of polymer used in the formulation. The overall supersaturation profile observed thus depended on a complex interplay between dissolution rate, polymer type, drug loading, and the kinetics of crystallization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Isotopic Substitution Reveals the Importance of Aluminate Diffusion Dynamics in Gibbsite (Al(OH) 3 ) Crystallization from Alkaline Aqueous Solution

Understanding molecular-scale factors governing the precipitation of aluminum hydroxides, such as gibbsite, under alkaline conditions is important for the formation of laterite deposits, as well as aluminum processing. However, mechanisms enabling tetrahedral aluminate ions to assemble into octahedral sites of the gibbsite lattice remain unclear. Formation of oligomeric complexes has been hypothesized as a critical intermediate step. Here, we report a study of gibbsite solubility in highly alkaline solutions using deuterium substitution to probe equilibrium and kinetic factors that could affect oligomeric intermediate formation, including the reactivity and the diffusivity of aluminate ions. When substituting sodium hydroxide with sodium deuteroxide, solution analysis shows a nearly 40% and 50% increase in gibbsite solubility in 2.4 and 3.3 mol·kg –1 total sodium solutions, respectively. Raman spectroscopy indicated that monomeric aluminate ions are the predominant species in solution irrespective of deuteration. However, both 27 Al and 23 Na nuclear magnetic resonance (NMR) spectroscopy revealed significant differences in chemical shifts in deuterated solutions, and analysis of 1 H, 23 Na, and 27 Al diffusion coefficients with pulsed-field gradient, stimulated echo NMR spectroscopy shows a decrease in ion diffusivity with increasing total deuterium in solution, consistent with the notion of increasing strength in the hydrogen/deuterium bonding network. In conclusion, because the relative change in 1 H diffusion coefficients are commensurate with the difference in apparent solubility constants, there is evidence for an oligomeric intermediate whose steady-state concentration is maintained by the collision frequency of aluminate ions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Density Measurements of Molten LiF–BeF 2 and LiF–BeF 2 –LaF 3 Salt Mixtures by Neutron Radiography

The densities of eutectic (LiF) 2 –BeF 2 and mixtures of this salt (FLiBe) with LaF 3 were measured by dilatometry and by neutron attenuation from 673 K to 1,073 K. Because LaF 3 has a limited solubility in FLiBe, it was necessary to determine the amount of LaF 3 in solution before the density could be determined. The FLiBe density determination was favorably benchmarked against the literature data. A simple comparison was not available for the LaF 3 –FLiBe mixtures, so extrapolation of published data was necessary based on analysis using the Molten Salt Thermal Properties Database-Thermochemistry, or MSTDB-TC, developed by the US Department of Energy. Solubilities for LaF 3 in FLiBe ranged from 1 to 4 mol % over 673 to 1,073 K. The salt system was heated and cooled over 24 h to evaluate potential changes in composition and hysteresis during the measurement. Changes in the meniscus were observed, and these were included in the correction for density determinations. Salt surface tension may have led to supersaturation of LaF 3 in the salt because the solubility curve was nonlinear with respect to the inverse temperature, as would be expected for an ideal system. Surface tension measurements are currently underway to test this hypothesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis of Butyl-Exchanged Polyoxymethylene Ethers as Renewable Diesel Blendstocks with Improved Fuel Properties

Methyl-terminated polyoxymethylene ethers (MM-POMEs), having the formula CH3O–(CH2O)n–CH3 (n = 3–5), are a high-cetane, low-sooting group of oxygenates that have recently attracted attention as potential diesel blendstocks. Despite these attractive fuel properties, MM-POMEs have shortcomings due to their low energy density and high water solubility. Guided by a computational fuel property assessment for POMEs with longer end-groups, the most promising improvements in the desired compression ignition fuel properties were observed for butyl-terminated POMEs. Here, an acid-catalyzed transacetalization reaction was developed to exchange the methyl end-groups of MM-POMEs (n = 3–6) with butyl end-groups. The reaction utilizes an ion-exchange resin as the acid catalyst at mild reaction conditions of 60 °C and atmospheric pressure. Approximately 100 mL of butyl-exchanged POMEs in the diesel boiling range were produced, enabling laboratory-scale fuel property testing. The butyl-terminated POME mixture possesses the advantaged fuel properties of the parent MM-POMEs (low-soot, high-cetane) while exhibiting improved energy density (lower heating value (LHV) of 30 MJ/kg) and substantially reduced water solubility (7.3 g/L) compared to the parent MM-POME mixture (LHV of 19 MJ/kg , water solubility of 258 g/L).

09 BIOMASS FUELS↗

Antibacterial Optimization of 4-Aminothiazolyl Analogues of the Natural Product GE2270 A: Identification of the Cycloalkylcarboxylic Acids

4-Aminothiazolyl analogues of the antibiotic natural product GE2270 A (1) were designed, synthesized, and optimized for their activity against Gram positive bacterial infections. Optimization efforts focused on improving the physicochemical properties (e.g., aqueous solubility and chemical stability) of the 4-aminothiazolyl natural product template while improving the in vitro and in vivo antibacterial activity. Structure-activity relationships were defined, and the solubility and efficacy profiles were improved over those of previous analogues and 1. These studies identified novel, potent, soluble, and efficacious elongation factor-Tu inhibitors, which bear cycloalkylcarboxylic acid side chains, and culminated in the selection of development candidates amide 48 and urethane 58.

60 APPLIED LIFE SCIENCES↗

The mechanism of magnetic properties improvement and microstructure refinement of Zr in Nd[subscript 2]Fe[subscript 14]B

In order to understand the role of Zr addition in Nd{sub 2}Fe{sub 14}B (2-14-1), a systematic study of Zr in Nd{sub 2}Fe{sub 14}B was done on a series of stoichiometric samples (Nd{sub 1-x}Zr{sub x}){sub 2}Fe{sub 14}B with 0 {le} x {le} 0.16. As-cast ingots formed significant amounts of Nd{sub 2}Fe{sub 17} starting at x = 0.06, while in the melt-spun ribbons, no Nd{sub 2}Fe{sub 17} was observed for the range studied. A monotonic decrease in lattice parameters for the 2-14-1 phase indicate Zr solubility in the melt-spun ribbons, but this is not observed in the ingots. Magnetic and thermal measurements on the ribbons showed that the saturated magnetization Ms (around 16 kG), the spin reorientation temperature (125 K), and the Curie temperature (583 K) do not depend on the Zr content, while the anisotropy field Ha slightly decreased as the Zr content increased. The energy product (BHmax) and the coercive force H{sub c} are highly dependent on the solidification and annealing process. Scanning electron microscopy and transmission electron microscopy on the as-melt spun alloys are consistent with x-ray diffraction showing Zr solubility in the 2-14-1 grains. After annealing, Zr diffuses to the grain boundaries to form Zr enriched compounds. Thus, while Zr may exhibit a metastable solubility in Nd{sub 2}Fe{sub 14}B, the enhanced magnetic behaviors observed in melt-spun ribbons are due to the refinement of the microstructure and enhanced grain-boundary pinning.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Vapor condensation onto a non-volatile liquid drop

Molecular dynamics simulations of miscible and partially miscible binary Lennard–Jones mixtures are used to study the dynamics and thermodynamics of vapor condensation onto a non-volatile liquid drop in the canonical ensemble. When the system volume is large, the driving force for condensation is low and only a submonolayer of the solvent is adsorbed onto the liquid drop. A small degree of mixing of the solvent phase into the core of the particles occurs for the miscible system. At smaller volumes, complete film formation is observed and the dynamics of film growth are dominated by cluster-cluster coalescence. Mixing into the core of the droplet is also observed for partially miscible systems below an onset volume suggesting the presence of a solubility transition. We also develop a non-volatile liquid drop model, based on the capillarity approximations, that exhibits a solubility transition between small and large drops for partially miscible mixtures and has a hysteresis loop similar to the one observed in the deliquescence of small soluble salt particles. The properties of the model are compared to our simulation results and the model is used to study the formulation of classical nucleation theory for systems with low free energy barriers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High thermoelectric potential of Bi{sub 2}Te{sub 3} alloyed GeTe-rich phases

In an attempt to reduce our reliance on fossil fuels, associated with severe environmental effects, the current research is focused on the identification of the thermoelectric potential of p-type (GeTe){sub 1−x}(Bi{sub 2}Te{sub 3}){sub x} alloys, with x values of up to 20%. Higher solubility limit of Bi{sub 2}Te{sub 3} in GeTe, than previously reported, was identified around ∼9%, extending the doping potential of GeTe by the Bi{sub 2}Te{sub 3} donor dopant, for an effective compensation of the high inherent hole concentration of GeTe toward thermoelectrically optimal values. Around the solubility limit of 9%, an electronic optimization resulted in an impressive maximal thermoelectric figure of merit, ZT, of ∼1.55 at ∼410 °C, which is one of the highest ever reported for any p-type GeTe-rich alloys. Beyond the solubility limit, a Fermi Level Pinning effect of stabilizing the Seebeck coefficient was observed in the x = 12%–17% range, leading to stabilization of the maximal ZTs over an extended temperature range; an effect that was associated with the potential of the governed highly symmetric Ge{sub 8}Bi{sub 2}Te{sub 11} and Ge{sub 4}Bi{sub 2}Te{sub 7} phases to create high valence band degeneracy with several bands and multiple hole pockets on the Fermi surface. At this compositional range, co-doping with additional dopants, creating shallow impurity levels (in contrast to the deep lying level created by Bi{sub 2}Te{sub 3}), was suggested for further electronic optimization of the thermoelectric properties.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Designing a mixture experiment when the components are subject to a nonlinear multiple-component constraint

This article presents a case study of developing an experimental design for a constrained mixture experiment when the experimental region is defined by single-component constraints (SCCs), linear multiple-component constraints (MCCs), and a nonlinear MCC. Traditional methods and software for designing constrained mixture experiments with SCCs and linear MCCs are not directly applicable because of the nonlinear MCC. A modification of existing methodology to account for the nonlinear MCC was developed and is described in this article. The case study involves a 15-component nuclear waste glass example in which SO3 is one of the components. SO3 has a solubility limit in glass that depends on the composition of the balance of the glass. A goal was to design the experiment so that SO3 would not exceed its predicted solubility limit for any of the experimental glasses. The SO3 solubility limit had previously been modeled by a partial quadratic mixture (PQM) model expressed in the relative proportions of the 14 other components. The PQM model was used to construct a nonlinear MCC in terms of all 15 components. In addition, there were SCCs and linear MCCs. This article discusses the waste glass example and how a layered design was generated to (i) account for the SCCs, linear MCCs, and nonlinear MCC and (ii) meet the goals of the study.

Low-activity waste↗