Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ships”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
NASA NTRS1924

Recent researches in airship construction II : bending stresses on an airship in flight

The first part of this report shows the differences between commercial and war airships and then goes on to show how some of the problems were solved. Their thorough investigations of these problems finally enabled the Schutte-Lanz Company to construct bulkhead diagrams for determining the buoyancy of airships, by means of which the size of each cell was established. These diagrams were derived from bulkhead diagrams employed in ship designing and are used in a similar manner.

AIRSHIPS - STRESSES, BENDING↗
NASA NTRS1927

Removing Boundary Layer by Suction

Through the utilization of the "Magnus effect" on the Flettner rotor ship, the attention of the public has been directed to the underlying physical principle. It has been found that the Prandtl boundary-layer theory furnishes a satisfactory explanation of the observed phenomena. The present article deals with the prevention of this separation or detachment of the flow by drawing the boundary layer into the inside of a body through a slot or slots in its surface.

AERODYNAMICS↗
NASA NTRS1927

Duralumin and Its Corrosion

The types of corrosion and factors of corrosion of duralumin are investigated. Salt water is the most common of the corroding media with which designers have to contend in using duralumin in aircraft and ships.

DURALUMIN - CORROSION↗
NASA NTRS1937

Experimental Investigation of the Problem of Surface Roughness

Based on the universal laws of turbulent velocity distribution at rough and smooth walls, there is in the present work presented a method that allows surface roughness tests and in particular, measurements on the roughness of ship surfaces to be carried out in a much simpler manner. The types of roughness investigated were in the form of flat, rough plates installed in a square-section rectangular channel, the other three walls always being smooth. Twenty-one plates of various roughness were investigated, the roughness elements being the following: spheres of diameter 0.41 and 0.21, respectively, spherical segments, cones, and "short" and "long" angles.

Schlichting, H↗
NASA NTRS1994

Parallel/Series-Fed Microstrip Array Antenna

Characteristics include low cross-polarization and high efficiency. Microstrip array antenna fabricated on two rectangular dielectric substrates. Produces fan-shaped beam polarized parallel to its short axis. Mounted conformally on outside surface of aircraft for use in synthetic-aperture radar. Other antennas of similar design mounted on roofs or sides of buildings, ships, or land vehicles for use in radar or communications.

Huang, John↗
NASA NTRS1994

Optoelectronic Receiver For Communication And Control

Many operational and diagnostic features integrated into circuit chip. GaAs-based integrated circuit designed to serve as optoelectronic interface in phased-array antenna. Intended function to receive digital control signals transmitted on optical fiber and to convert signals to electronic control signals, which then applied to monolithic microwave integrated circuit (MMIC). Also used in reception of high-rate optical digital communications within computers, between computers, and in signal-distribution systems in aircraft, automobiles, and ships. Interface circuit represents significant improvement over preexisting interface circuits in that its clock-signal-recovery subcircuit requires little or no preamble for immediate synchronization.

Kunath, Richard↗
NASA NTRS1994

Lightweight Tool Grinds Back-Side Weld Beads

Air-powered grinder enables high-quality rework of welds. Tool removes excess material from back side of weld in preparation for reworking. Used on workpiece while workpiece still mounted in welding fixture or welding machine. Then rewelded in original position, so full process control maintained. Used for grinding material in spaces to which access limited, such as in pressure vessels and in hulls of ships. Also used to grind materials other than metals.

Gallagher, Robert L.↗
NASA NTRS1994

Dither Helps Compensate For Friction In Reaction Wheel

Dither control and generator unit incorporated into reaction-wheel attitude-control system to help compensate for error caused by friction in reaction-wheel bearings at and near zero speed of wheel. Reaction-wheel attitude-control system designed primarily to maintain desired orientation of spacecraft but also useful in maintaining desired orientation of terrestrial antenna, optical instrument, or other device on aircraft, ship, land vehicle, or other moving platform. Alternating torque sufficient to overcome static friction applied at low speed.

Stetson, John B., Jr.↗
NASA NTRS1994

Generating High-Pressure Oxygen Electrolytically

Electrolytic cell generates oxygen directly at high pressure at point of use. System makes it unnecessary to use heavy, bulky air compressor or to ship compressed oxygen in heavy tanks. Produces hydrogen as byproduct, at pressure that may be different from that of oxygen, if desired. Cathode also barrier that lets gases collect at widely differing pressures.

Schubert, F. H.↗
NASA NTRS1994

High-Storage-Capacity Accelerometer System

Instrumentation system measures and records accelerations at frequencies from 0 to 100 Hz and magnitudes from 10 to the negative 5th power to 0.5 g. Developed to aid research on small accelerations in spacecraft in orbit. Also used on Earth: with modified acceleration sensors to monitor acceleration environments of sensitive products transported by airplanes, railroad trains, trucks, or ships.

Chase, Theodore L.↗
NASA NTRS1994

Monolithic Optical-To-Electronic Receiver

Monolithic optoelectronic integrated circuit converts multiplexed digital optical signals into electrical signals, separates, and distributes them to intended destinations. Developed to deliver phase and amplitude commands to monolithic microwave integrated circuits (MMIC's) at elements of millimeter-wave phased-array antenna from single optical fiber driven by external array controller. Also used in distribution of high-data-rate optical communications in local-area networks (LAN's). Notable features include options for optical or electrical clock inputs; outputs for raw data, addresses, and instructions for diagnosis; and optical-signal-detection circuit used to reduce power consumption by 80 percent between data-transmission times. Chip fabricated by processes available at many major semiconductor foundries. Distribution of digital signals in aircraft, automobiles, and ships potential application.

Kunath, Richard↗
NASA NTRS1994

Numerical Simulation Of Cutting Of Gear Teeth

Shapes of gear teeth produced by gear cutters of specified shape simulated computationally, according to approach based on principles of differential geometry. Results of computer simulation displayed as computer graphics and/or used in analyses of design, manufacturing, and performance of gears. Applicable to both standard and non-standard gear-tooth forms. Accelerates and facilitates analysis of alternative designs of gears and cutters. Simulation extended to study generation of surfaces other than gears. Applied to cams, bearings, and surfaces of arbitrary rolling elements as well as to gears. Possible to develop analogous procedures for simulating manufacture of skin surfaces like automobile fenders, airfoils, and ship hulls.

Oswald, Fred B.↗
NASA NTRS1994

Dual-Mode Adhesive Pad

Tool helps worker grip and move along large, smooth structure with no handgrips or footholds. Adheres to surface but easily released by actuating simple mechanism. Includes handle and segmented contact-adhesive pad. Bulk of pad made of soft plastic foam conforming to surface of structure. Each segment reinforced with rib. In sticking mode, ribs braced by side catches. In peeling mode, side catches retracted, and segmented adhesive pad loses its stiffness. Modified versions useful in inspecting hulls of ships and scaling walls in rescue operations.

Hartz, Leslie↗
NASA NTRS1989

Project ARGO: The design and analysis of an all-propulsive and an aeroassisted version of a manned space transportation vehicle

The Senior Aerospace System Design class at the University of Michigan undertook the design of a manned space transportation vehicle (STV) that would transport payloads between low earth orbit (LEO) and geosynchronous earth orbit (GEO). Designated ARGO after the ship of the Greek adventurer Jason, two different versions of an STV that would be based, refueled, and serviced at the Space Station Freedom were designed and analyzed by the class. With the same 2-man/7-day nominal mission of transporting a 10,000-kg payload up to GEO and bringing a 5000-kg payload back to LEO, the two versions of ARGO differ in the manner in which the delta V is applied to insert the vehicle into LEO upon return from GEO. The all-propulsive ARGO (or CSTV for chemical STV) uses thrust from its LH2/LOX rocket engines to produce the delta V during all phases of its mission. While the aeroassisted ARGO (or ASTV for aeroassisted STV) also uses the same engines for the majority of the mission, the final delta V used to insert the ASTV into LEO is produced by skimming the Earth's atmosphere and using the drag on the vehicle to apply the required delta V. This procedure allows for large propellant, and thus cost, savings, but creates many design problems such as the high heating rates and decelerations experienced by a vehicle moving through the atmosphere at hypersonic velocities. The design class, consisting of 43 senior aerospace engineering students, was divided into one managerial and eight technical groups. The technical groups consisted of spacecraft configuration and integration, mission analysis, atmospheric flight, propulsion, power and communications, life support and human factors, logistics and support, and systems analysis. Two committees were set up with members from each group to create the scale models of the STV's and to produce the final report.

Wang, H.↗
NASA NTRS1989

Laser powered interorbital vehicle

A preliminary design of a low-thrust Laser Powered Interorbital Vehicle (LPIV) intended for cargo transportation between an Earth space station and a lunar base is presented. The selected mission utilizes a spiral trajectory, characteristic of a low-thrust spacecraft, requiring eight days for a lunar rendezvous and an additional nine days for return. The ship's configuration consists primarily of an optical train, two hydrogen plasma engines, a 37.1 m box-beam truss, a payload module, and propellant tanks. The total mass of the vehicle, fully loaded, is 63,300 kg. A single plasma, regeneratively cooled engine design is incorporated into the two 500 N engines. These are connected to the spacecraft by turntables that allow the vehicle to thrust tangential to the flight path. Proper collection and transmission of the laser beam to the thrust chambers is provided through the optical train. This system consists of a 23-m-diameter primary mirror, a convex parabolic secondary mirror, a beam splitter, and two concave parabolic tertiary mirrors. The payload bay is capable of carrying 18,000 kg of cargo and is located opposite the primary mirror on the main truss. Fuel tanks carrying a maximum of 35,000 kg of liquid hydrogen are fastened to tracks that allow the tanks to be moved perpendicular to the main truss. This capability is required to prevent the center of mass from moving out of the thrust vector line. The laser beam is located and tracked by means of an acquisition, pointing, and tracking system that can be locked onto the space-based laser station. Correct orientation of the spacecraft with the laser beam is maintained by control moment gyros and reaction control rockets. In addition, an aerobrake configuration was designed to provide the option of using the atmospheric drag in place of propulsion for a return trajectory.

Clarke, M. T.↗
NASA NTRS1989

Advanced solar-propelled cargo spacecraft for Mars missions

At the University of Washington, three concepts for an unmanned, solar powered, cargo spacecraft for Mars-support missions have been investigated. These spacecraft are designed to carry a 50,000 kg payload from a low Earth orbit to a low Mars orbit. Each design uses a distinctly different propulsion system: a solar radiation absorption (SRA) system, a solar-pumped laser (SPL) system, and a solar powered mangetoplasmadynamic (MPD) arc system. The SRA directly converts solar energy to thermal energy in the propellant through a novel process developed at the University of Washington. A solar concentrator focuses sunlight into an absorption chamber. A mixture of hydrogen and potassium vapor absorbs the incident radiation and is heated to approximately 3700 K. The hot propellant gas exhausts through a nozzle to produce thrust. The SRA has an I(sub sp) of approximately 1000 sec and produces a thrust of 2940 N using two thrust chambers. In the SPL system, a pair of solar-pumped, multi-megawatt, CO2 lasers in sun-synchronous Earth orbit converts solar energy to laser energy. The laser beams are transmitted to the spacecraft via laser relay satellites. The laser energy heats the hydrogen propellant through a plasma breakdown process in the center of an absorption chamber. Propellant flowing through the chamber, heated by the plasma core, expands through a nozzle to produce thrust. The SPL has an I(sub sp) of 1285 sec and produces a thrust of 1200 N using two thrust chambers. The MPD system uses indium phosphide solar cells to convert sunlight to electricity, which powers the propulsion system. In this system, the argon propellant is ionized and electromagnetically accelerated by a magnetoplasmadynamic arc to produce thrust. The MPD spacecraft has an I(sub sp) of 2490 sec and produces a thrust of 100 N. Various orbital transfer options are examined for these concepts. In the SRA system, the mother ship transfers the payload into a very high Earth orbit and a small auxiliary propulsion system boosts the payload into a Hohmann transfer to Mars. The SPL spacecraft releases the payload as the spacecraft passes by Mars. Both the SRA-powered spacecraft and the SPL-powered spacecraft return to Earth for subsequent missions. The MPD-propelled spacecraft, however, remains at Mars as an orbiting space station. A patched conic approximation was used to determine a heliocentric interplanetary transfer orbit for the MPD propelled spacecraft. All three solar-powered spacecraft use an aerobrake procedure to place the payload into a low Mars parking orbit. The payload delivery times range from 160 days to 873 days (2.39 years).

Auziasdeturenne, J.↗
NASA NTRS1989

Design of a spanloader cargo aircraft

With a growing demand for fast international freight service, the slow-moving cargo ships currently in use will soon find a substantial portion of their clients looking elsewhere. One candidate for filling this expected gap in the freight market is a span-loading aircraft (or 'flying wing') capable of long-range operation with extremely large payloads. This report summarizes the design features of an aircraft capable of fulfilling a long-haul, high-capacity cargo mission. The spanloader seeks to gain advantage over conventional aircraft by eliminating the aircraft fuselage and thus reducing empty weight. The primary disadvantage of this configuration is that the cargo-containing wing tends to be thick, thus posing a challenge to the airfoil designer. It also suffers from stability and control problems not encountered by conventional aircraft. The result is an interesting, challenging exercise in unconventional design. The report that follows is a student written synopsis of an effort judged to be the best of eight designs developed during the year 1988-1989.

Source record↗