Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Spinning for safety's sake

NASA Langley is currently engaged in a comprehensive research program to improve the stall/spin characteristics of general aviation airplanes. Part of this program has included systematic flight tests of a fully instrumented airplane to determine the effects of various tail, wing, and fuselage modifications, and variation of inertia, center-of-gravity, and control positions on the spin and recovery characteristics. Airplane equipment, onboard instrumentation ground equipment, test area, and test procedures have been combined to provide a safe, practical means for conducting research in preplanned hazardous conditions. Configuration changes produced spins varying from easily recoverable to unrecoverable, and wind section design significantly influenced airplane stall, spin, and recovery characteristics.

Stough, H. P., III↗

Flight evaluation of the effect of winglets on performance and handling qualities of a single-engine general aviation airplane

A flight evaluation was conducted to determine the effects of winglets on the performance and handling qualities of a light, single-engine general aviation airplane. The performance measurements were made with a pace airplane to provide calibrated airspeeds; uncalibrated panel instruments in the test airplane were used to provide additional quantitative performance data. These tests were conducted with winglets on and off during the same day to measure relative performance effects. Handling qualities were evaluated by means of pilot comments. Winglets increased cruise speed 8 knots (5.6 percent) at 3962 m (13,000 ft) density altitude and 51 percent maximum continuous power setting. Maximum speed at 3962 m was virtually unchanged. Rate of climb increased approximately 6 percent, or 0.25 m/sec (50 ft/min), at 1524 m (5000 ft). Stall speed was virtually unchanged. Handling qualities were favorably affected.

Holmes, B. J.↗

Experimental investigation of vortices shed by various wing fin configurations

Forty-six different fins, which were members of twelve plan-form families, were tested. A two dimensional Boeing single element airfoil at an angle of attack of eight degrees and a sweepback angle of thirty-two was used to simulate a portion of the wing of a generator aircraft. Various free stream velocities were used to test any individual fin at its particular angle of attack. While the fin itself was mounted on the upper surface of the generator model, the angle of attack of each fin was varied until stall was reached and/or passed. The relative fin vortex strengths were measured in two ways. First, the maximum angular velocity of a four blade rotor placed in the fin vortex center was measured with the use of a stroboscope. Second, the maximum rolling moment on a following wing model placed in the fin vortex center was measured by a force balance.

Iversen, J.↗

Some wake-related operational limitations of rotorcraft

Wind tunnel measurements show that the wake of a rotor, except at near hovering speeds, is not like that of a propeller. The wake is more like that of a wing except that, because of the slow speeds, the wake velocities may be much greater. The helicopter can produce a wake hazard to following light aircraft that is disproportionately great compared to an equivalent fixed wing aircraft. This hazard should be recognized by both pilots and airport controllers when operating in congested areas. Ground effect is generally counted as a blessing since it allows overloaded takeoffs; however, it also introduces additional operation problems. These problems include premature blade stall in hover, settling in forward transition, shuddering in approach to touchdown and complicatons with yaw control. Some of these problems were treated analytically in an approximate manner and reasonable experiment agreement was obtained. An awareness of these effects can prepare the user for their appearance and their consequences.

Heyson, H. H.↗

Extended frequency turbofan model

The fan model was developed using two dimensional modeling techniques to add dynamic radial coupling between the core stream and the bypass stream of the fan. When incorporated into a complete TF-30 engine simulation, the fan model greatly improved compression system frequency response to planar inlet pressure disturbances up to 100 Hz. The improved simulation also matched engine stability limits at 15 Hz, whereas the one dimensional fan model required twice the inlet pressure amplitude to stall the simulation. With verification of the two dimensional fan model, this program formulated a high frequency F-100(3) engine simulation using row by row compression system characteristics. In addition to the F-100(3) remote splitter fan, the program modified the model fan characteristics to simulate a proximate splitter version of the F-100(3) engine.

Mason, J. R.↗

Flight test evaluation of predicted light aircraft drag, performance, and stability

A technique was developed which permits simultaneous extraction of complete lift, drag, and thrust power curves from time histories of a single aircraft maneuver such as a pull up (from V max to V stall) and pushover (to V max for level flight). The technique, which is an extension of nonlinear equations of motion of the parameter identification methods of Iliff and Taylor and includes provisions for internal data compatibility improvement as well, was shown to be capable of correcting random errors in the most sensitive data channel and yielding highly accurate results. Flow charts, listings, sample inputs and outputs for the relevant routines are provided as appendices. This technique was applied to flight data taken on the ATLIT aircraft. Lack of adequate knowledge of the correct full throttle thrust horsepower true airspeed variation and considerable internal data inconsistency made it impossible to apply the trajectory matching features of the technique.

Smetana, F. O.↗

US and USSR Military Aircraft and Missile Aerodynamics 1970-1980. A selected, annotated bibliography, volume 1

The purpose of this selected bibliography (281 citations) is to list available, unclassified, unlimited publications which provide aerodynamic data on major aircraft and missiles currently used by the military forces of the United States of America and the Union of Soviet Socialist Republics. Technical disciplines surveyed include aerodynamic performance, static and dynamic stability, stall-spin, flutter, buffet, inlets nozzles, flap performance, and flying qualities. Concentration is on specific aircraft including fighters, bombers, helicopters, missiles, and some work on transports, which are or could be used for military purposes. The bibliography is limited to material published from 1970 to 1980. The publications herein illustrate many of the types of aerodynamic data obtained in the course of aircraft development programs and may therefore provide some guidance in identifying problems to be expected in the conduct of such work. As such, this information may be useful in planning future research programs.

Tuttle, M. H.↗

Applications of dynamic stability parameters to problems in aircraft dynamics

The application and analysis of dynamic stability parameters were examined. The effects of wing leading edge modifications on the stalling and spinning characteristics of a single engine general aviation research airplane are evaluated. It is illustrated how dynamic stability parameters measured in wind tunnel tests are used to predict the spin resistance of this class of aircraft, and that autorotation criteria are derived from the relationships which exist between static and dynamic aerodynamic characteristics.

Chambers, J. R.↗

Evaluation of pressure and thermal data from a wind tunnel test of a large-scale, powered, STOL fighter model

A STOL fighter model employing the vectored-engine-over wing concept was tested at low speeds in the NASA/Ames 40 by 80-foot wind tunnel. The model, approximately 0.75 scale of an operational fighter, was powered by two General Electric J-97 turbojet engines. Limited pressure and thermal instrumentation were provided to measure power effects (chordwise and spanwise blowing) and control-surface-deflection effects. An indepth study of the pressure and temperature data revealed many flow field features - the foremost being wing and canard leading-edge vortices. These vortices delineated regions of attached and separated flow, and their movements were often keys to an understanding of flow field changes caused by power and control-surface variations. Chordwise blowing increased wing lift and caused a modest aft shift in the center of pressure. The induced effects of chordwise blowing extended forward to the canard and significantly increased the canard lift when the surface was stalled. Spanwise blowing effectively enhanced the wing leading-edge vortex, thereby increasing lift and causing a forward shift in the center of pressure.

Howell, G. A.↗

A status report on NASA general aviation stall/spin flight testing

The NASA Langley Research Center has undertaken a comprehensive program involving spin tunnel, static and rotary balance wind tunnel, full-scale wind tunnel, free flight radio control model, flight simulation, and full-scale testing. Work underway includes aerodynamic definition of various configurations at high angles of attack, testing of stall and spin prevention concepts, definition of spin and spin recovery characteristics, and development of test techniques and emergency spin recovery systems. This paper presents some interesting results to date for the first aircraft (low-wing, single-engine) in the program, in the areas of tail design, wing leading edge design, mass distribution, center of gravity location, and small airframe changes, with associated pilot observations. The design philosophy of the spin recovery parachute system is discussed in addition to test techniques.

Patton, J. M., Jr.↗

Hinged strakes for enhanced maneuverability at high angles of attack

A controllable-strake concept for alleviating the adverse effects of strake vortex breakdown and asymmetry on the longitudinal and lateral aerodynamics of strake-wing configurations at high angles of attack is presented. The concept aims to control the strake load independently of angle of attack and sideslip by varying the anhedral angle of strakes hinged along the root chord. The strakes may be deflected in a symmetrical or nonsymmetrical mode for a variety of control functions. Results are presented of an exploratory wind-tunnel investigation to evaluate the potential of the hinged-strake concept for enhancing the three-axis controllability in post-stall flight.

Rao, D. M.↗

Simulated aircraft takeoff performance with frosted wings

The absolute and relative safety of certain nocturnal frost formations on general aviation and transport type airfoils is evaluated by a computer simulation program. The frost layer aerodynamic penalty and takeoff program was used to calculate the frost thickness distribution on an airfoil with time, as well as the aerodynamic penalties associated with the frost layer during takeoff. The program was validated by nocturnal frost formation experiments on an inclined flat plate and by comparisons with documented aerodynamic penalties of an arbitrarily roughened airfoil. For various meteorological conditions and runway take-off velocities, a frost layer can be determined that produces no aerodynamic penalty, thus inferring the absolute safety of the airfoil with respect to frost. The relative safety of a frosted airfoil depends on the ability of the engine power reserve to overcome both as much as doubling of airfoil drag and an increased stall speed due to lift penalties.

Dietenberger, M. A.↗

A discrete vortex method for the non-steady separated flow over an airfoil

A discrete vortex method was used to analyze the separated non-steady flow about a cambered airfoil. The foil flow modelling is based on the thin lifting-surface approach, where the chordwise location of the separation point is assumed to be known from experiments or flow-visualization data. Calculated results provided good agreement when compared with the post-stall aerodynamic data of two airfoils. Those airfoil sections differed in the extent of travel of the separation point with increasing angle of attack. Furthermore, the periodic wake shedding was analyzed and its time-dependent influence on the airfoil was investigated.

Katz, J.↗

Applications of dynamic stability parameters to problems in aircraft dynamics

The paper presents highlights of a recent study which illustrates the application and analysis of dynamic stability parameters. More specifically, the investigation consisted of an evaluation of the effects of wing leading-edge modifications on the stalling and spinning characteristics of a single-engine general aviation research airplane. The results of the investigation illustrate how dynamic stability parameters measured in wind-tunnel tests are used to predict the spin resistance of this class of aircraft; and that autorotation criteria can be derived from the relationships which exist between static and dynamic aerodynamic characteristics.

Chambers, J. R.↗

Computation of separated flows by a vortex-tracing algorithm

Numerical solutions for two-dimensional, time-dependent, separated flows around bodies are obtained, using a new version of the vortex method. This method provides an efficient representation of flows involving large regions of separation. The modifications incorporated in the new version, which improve its accuracy, versatility, and computing speed, are described. The computer cost is only of the order of the 3/2 power on N, instead of N-squared, for each step with N vortices. Arbitrary shapes can be treated; a conformal mapping is not required. Special attention is paid to the viscous character of the solution and to the accurate computation of the pressure distribution at the body surface. The vortex solution for the outer flow is coupled to an inner solution for the attached part of the boundary layer. Numerical results are presented for several bluff bodies exhibiting dependence on Reynolds number, for stationary airfoils under steady or transient conditions and for oscillating airfoils, including dynamic stalls. These results are compared with other available results, analytical or experimental, and demonstrate the enhanced reliability and accuracy of the improved method.

Spalart, P. R.↗

Trailing edge noise from hovering rotors

A method has been developed to predict the high frequency broadband noise due to the interaction of convecting turbulent eddies with the trailing edges of a hovering rotor. The trailing edge noise from each blade was modeled as point dipole noise with spanwise loading corrections. This point dipole approximation was checked by applying the concept to a stationary airfoil in a moving medium with excellent results. In order to estimate the strength of the point dipole, the trailing edge noise theory of Amiet was used. The method was applied specifically to blade boundary layer turbulence and compared to incident atmospheric turbulence noise. The results indicate that the relative importance of these two mechanisms is related to the magnitudes of the intensity and of the length scales of the inflow and boundary layer turbulence. The results tend to fall below some available experimental data indicating that in those experiments other broadband noise sources were stronger than boundary layer-trailing edge noise. The approach which was developed is also applicable to other blade-turbulence interaction mechanisms such as local stall and tip noise.

Kim, Y. N.↗

Helicopter theory

A comprehensive presentation is made of the engineering analysis methods used in the design, development and evaluation of helicopters. After an introduction covering the fundamentals of helicopter rotors, configuration and operation, rotary wing history, and the analytical notation used in the text, the following topics are discussed: (1) vertical flight, including momentum, blade element and vortex theories, induced power, vertical drag and ground effect; (2) forward flight, including in addition to momentum and vortex theory for this mode such phenomena as rotor flapping and its higher harmonics, tip loss and root cutout, compressibility and pitch-flap coupling; (3) hover and forward flight performance assessment; (4) helicopter rotor design; (5) rotary wing aerodynamics; (6) rotary wing structural dynamics, including flutter, flap-lag dynamics ground resonance and vibration and loads; (7) helicopter aeroelasticity; (8) stability and control (flying qualities); (9) stall; and (10) noise.

Johnson, W.↗

Wind-tunnel measurements of wing-canard interference and a comparison with various theories

Wind-tunnel tests and analyses of the aerodynamics of wing-canard combinations for low speed applications are presented. Systematic tests are conducted in a 7 x 10 wind tunnel to explore various combinations of wing-canard vertical and horizontal positioning. The goals of the tests are (1) to investigate potential improved stalling characteristics over conventional tail-aft configurations, (2) to investigate the existence of a lift coefficient advantage, and (3) to determine induced drag levels. The measurements obtained are compared with calculations made using the Prandtl-Munk theory, and with a vortex-lattice panel code. Results indicate that the panel code gives excellent results for lift and induced drag at moderate lift coefficient, whereas Prandtl-Munk theory gives conservative results for induced drag. The application is a light transport aircraft used for short-haul operations.

Feistel, T. W.↗