Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Permeability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Influence of microstructure on replacement and porosity generation during experimental dolomitization of limestones

Replacement reactions commonly alter the multiscale pore structures of rocks during fluid-rock interactions. Analysis of these processes in various model fluid-rock systems during controlled laboratory experiments provides insights into the origins of microstructures found in natural materials. This study focused on understanding the effects of initial starting material permeability and resultant differences in transport pathways on porosity and mineralogical changes during limestone dolomitization.A series of replacement experiments (32–317 days in duration) have been conducted in which 1.59 cm (5/8 in.) diameter cores of two different limestones were reacted with saturated MgCl2 solutions at 200 °C. The Texas Cream (Austin Chalk) is a high-porosity, high-permeability limestone, whereas both the porosity and permeability of the Carthage Marble (Burlington Limestone) are relatively low. Altered limestones were imaged using scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), Time-of-Flight Secondary Ion Mass Spectrometry (ToF–SIMS) and electron microprobe analysis (EMPA). A representative grain boundary of the low-porosity limestone was targeted for a focused ion beam (FIB) lift-out and characterized using transmission electron microscopy (TEM). These results were coupled with analyses of radial changes in the porosity distribution of the core derived from X-ray and neutron small- and ultra-small angle scattering ((U)SANS/(U)SAXS).The high-porosity/permeability limestone showed a four times faster bulk replacement rate than the lower-porosity/permeability material, and a different mechanism of porosity development. For the low-porosity limestone, a two-stage replacement occurred, with the reacted region of the core consisting of an inner rim in which the limestone was replaced by two calcite-dolomite solid solutions, and an outer rim in which the dolomite was replaced by magnesite. Elongated pores formed along grain boundaries at the initial limestone/dolomite reaction interface, and additional nanometer-scale porosity was formed at the secondary magnesite replacement rim. Grain boundaries were identified as preferential pathways for transport leading to dolomitization and a grain boundary diffusion rate was calculated based on microstructural characterization. In contrast, replacement in the high-porosity limestone was accompanied by porosity generation through replacement of individual grains by dolomite throughout the sample and, in longer runs, magnesite in outer parts of the core. These observations emphasize that both the mechanisms of the replacement reaction and the microstructure and chemistry of the replaced product are contingent on the initial structure of the starting material.

36 MATERIALS SCIENCE↗

CO 2 storage site characterization using ensemble-based approaches with deep generative models

Estimating spatially distributed properties such as permeability from available sparse measurements is a great challenge in efficient subsurface CO 2 storage operations. In this paper, a deep generative model that can accurately capture complex subsurface structure is tested with an ensemble-based inversion method for accurate and accelerated characterization of CO 2 storage sites. We chose Wasserstein Generative Adversarial Network with Gradient Penalty (WGAN-GP) for its realistic reservoir property representation and Ensemble Smoother with Multiple Data Assimilation (ES-MDA) for its robust data fitting and uncertainty quantification capability. WGAN-GP are trained to generate high-dimensional permeability fields from a low-dimensional latent space and ES-MDA then updates the latent variables by assimilating available measurements. Several subsurface site characterization examples including Gaussian, channelized, and fractured reservoirs are used to evaluate the accuracy and computational efficiency of the proposed method and the main features of the unknown permeability fields are characterized accurately with reliable uncertainty quantification. Furthermore, the estimation performance is compared with a widely-used variational, i.e., optimization-based, inversion approach, and the proposed approach outperforms the variational inversion method in several benchmark cases. We explain such superior performance by visualizing the objective function in the latent space: because of nonlinear and aggressive dimension reduction via generative modeling, the objective function surface becomes extremely complex while the ensemble approximation can smooth out the multi-modal surface during the minimization. This suggests that the ensemble-based approach works well over the variational approach when combined with deep generative models at the cost of forward model runs unless convergence-ensuring modifications are implemented in the variational inversion.

42 ENGINEERING↗

Play-fairway analysis for geothermal resources and exploration risk in the Modoc Plateau region

The region surrounding the Modoc Plateau, encompassing parts of northeastern California, southern Oregon, and northwestern Nevada, lies at an intersection between two tectonic provinces; the Basin and Range province and the Cascade volcanic arc. Both of these provinces have substantial geothermal resource base and resource potential. Geothermal systems with evidence of magmatic heat, associated with Cascade arc magmatism, typify the western side of the region. Systems on the eastern side of the region appear to be fault controlled with heat derived from high crustal heat flow, both of which are typical of the Basin and Range. As it has the potential to host Cascade arc-type geothermal resources, Basin and Range-type geothermal resources, and/or resources with characteristics of both provinces, and because there is relatively little current development, the Modoc Plateau region represents an intriguing potential for undiscovered geothermal resources. It remains unclear however, what specific set(s) of characteristics are diagnostic of Modoc-type geothermal systems and how or if those characteristics are distinct from Basin and Range-type or Cascade arc-type geothermal systems. In order to evaluate the potential for undiscovered geothermal resources in the Modoc area, we integrate a wide variety of existing data in order to evaluate geothermal resource potential and exploration risk utilizing ‘play-fairway’ analysis. Here, we consider that the requisite parameters for hydrothermal circulation are: 1) heat that is sufficient to drive circulation, and 2) permeability that is sufficient to allow for fluid circulation in the subsurface. We synthesize data that indicate the extent and distribution of these parameters throughout the Modoc region. ‘Fuzzy logic’ is used to incorporate expert opinion into the utility of each dataset as an indicator of either heat or permeability, and thus geothermal favorability. The results identify several geothermal prospects, areas that are highly favorable for the occurrence of both heat and permeability. These are also areas where there is sufficient data coverage, quality, and consistency that the exploration risk is relatively low. These unknown, undeveloped, and under-developed prospects are well-suited for continued exploration efforts. The results also indicate to what degree the two ‘play-types,’ i.e. Cascade arc-type or Basin and Range-type, apply to each of the geothermal prospects, a useful guide in exploration efforts.

15 GEOTHERMAL ENERGY↗

Corrigendum to "Environmentally friendly, rheoreversible, hydraulic fracturing fluids for enhanced geothermal systems" [Geothermics 58 (2015) 22–31]

Cost-effective creation of high-permeability reservoirs inside deep crystalline bedrock is the primary challenge for the feasibility of enhanced geothermal systems (EGS). Current reservoir stimulation entails adverse environmental impacts and substantial economic costs due to the utilization of large volumes of water “doped” with chemicals including rheology modifiers, scale and corrosion inhibitors, biocides, friction reducers among others where, typically, little or no information of composition and toxicity is disclosed. An environmentally benign, CO2-activated, rheoreversible fracturing fluid has recently been developed that significantly enhances rock permeability at effective stress significantly lower than current technology. We evaluate the potential of this novel fracturing fluid for application on geothermal sites under different chemical and geomechanical conditions, by performing laboratory-scale fracturing experiments with different rock sources under different confining pressures, temperatures, and pH environments. The results demonstrate that CO2-reactive aqueous solutions of environmentally amenable Polyallylamine (PAA) represent a highly versatile fracturing fluid technology. This fracturing fluid creates/propagates fracture networks through highly impermeable crystalline rock at significantly lower effective stress as compared to control experiments where no PAA was present, and permeability enhancement was significantly increased for PAA compared to conventional hydraulic fracturing controls. This was evident in all experiments, including variable rock source/type, operation pressure and temperature (over the entire range for EGS applications), as well as over a wide range of formation-water pH values. This versatile novel fracturing fluid technology represents a great alternative to industrially available fracturing fluids for cost-effective and competitive geothermal energy production.

Shao, Hongbo↗

Self-Repairing Polymer-Modified Cements for High Temperature Geothermal and Fossil Energy Applications

In this work five novel polymer-cement composite formulations were prepared and evaluated as potential cementitious material alternatives to conventional wellbore cement. These cement composites were cured at 200 °C and their mechanical properties, including compressive strength, Young modulus, shear bond strength to steel casing, and self-healing and re-adhering (to steel) capability. Thermal stability was also evaluated by curing these cement materials at 200 °C for up to one month followed by determining their mineralogy and chemical composition by X-ray diffraction spectroscopy, 13C NMR, and total organic carbon. Permeability analysis was performed before and after healing a longitudinal fracture on unmodified cements and polymer-cement composites with the later showing lower (2nd/1st) permeability ratios with respect to base cements. Furthermore, a reduction in permeability of up to 80X on average with respect to their unmodified (base) cement, was observed in two polymer-cement formulations suggesting that the introduction of these polymers bring about self-healing capability. Two of the best performing polymer-cement composites were exposed to 30-day curing period at 200 °C showing that their self-healing capability is maintained. The composite stability is associated to the fact that the polymer material is stable as demonstrated by total organic carbon and NMR spectroscopy. These advanced polymer-cement composites with higher ductility and self-healing capability could be used as alternative wellbore cement materials for geothermal and fossil energy applications.

Rod, Kenton A.↗

Modeling study of deep direct use geothermal on the West Virginia university campus-morgantown, WV

To reduce the geothermal exploration risk, a feasibility study is performed for a deep direct-use (DDU) system proposed at the West Virginia University (WVU) Morgantown campus. This study applies numerical simulations to investigate reservoir impedance and thermal production. Because of the great depth of the geothermal reservoir, few data are available to characterize reservoir features and properties. Consequently, the study focuses on the following three aspects: 1. model choice for predicting reservoir impedance and thermal breakthrough: after investigating three potential models (one single permeability model and two dual permeability models) for flow through fractured rock, it is decided only the single permeability model is needed; 2. well placement (horizontal vs. vertical) options: horizontal well placement seems to be more robust to heterogeneity and the impedance is more acceptable; 3. Prediction uncertainty: the most influential parameters are identified using a First-Order-Second-Moment uncertainty propagation analysis, and the uncertain range of the model predictions is estimated by performing a Monte Carlo simulation. Heterogeneity has a large impact on the prediction, therefore, heterogeneity is included in the predictive model and uncertainty analysis. The numerical model results and uncertainty analysis will be used for further economic studies.

15 GEOTHERMAL ENERGY↗

Simulation of carbon dioxide injection at the FutureGen2.0 site: Class VI permit model and local sensitivity analysis

Numerical simulation was conducted to evaluate supercritical CO 2 (scCO 2 ) storage in the Mt. Simon sandstone at the FutureGen 2.0 site in Morgan County, Illinois. The simulations illustrate the recent modeling effort conducted to successfully obtain a Class VI permit under the Underground Injection Control Program of the U.S. Environmental Protection Agency. The scCO2 was injected into a highly stratified reservoir, distributed among four lateral wells. Results show that each of the multiple reservoir layers with low permeability traps a fraction of the scCO 2 beneath it so that the injected scCO 2 does not reach the top of the reservoir by the end of the simulation period. Hence, all of the injected scCO 2 is considered to be safely trapped by the stratified structure within the reservoir. A local sensitivity analysis (LSA) was conducted for injectivity and plume size at the end of the 20 year injection period. The LSA indicates that the imposed initial conditions and the hydraulic properties of the injection layer contribute the most to the sensitivity. Overall, the simulation outputs are very sensitive to only a small fraction of the inputs. However, the parameters that are important for controlling CO 2 injectivity are not the same as those controlling the plume area. The three most sensitive inputs for injectivity are the horizontal permeability and the residual aqueous saturation of the injection layer, and the initial fracture-pressure gradient. For the plume area, the most sensitive inputs are the horizontal permeability of the injection layer and the residual aqueous saturation of the two adjacent layers above the injection layer. Furthermore, the advantages of requiring just a single set of simulation results, scalability to the proper parameter errors, and straightforward calculation of the composite sensitivities make the proposed analysis attractive for guiding site characterization, injection well design, estimating AoR uncertainty and, and monitoring network design.

54 ENVIRONMENTAL SCIENCES↗

Fines migration during CO 2 injection: Experimental results interpreted using surface forces

The South West Hub project is one of the Australian Flagship Carbon Capture and Storage projects located in the south-west of Western Australia. To evaluate the injectivity potential during the forthcoming full-scale CO 2 injection, we conducted three core-flooding experiments using reservoir core plugs from the well Harvey-1. We aimed to investigate in this paper whether the injection of CO 2 leads to fines migration and permeability reduction due to the relatively high kaolinite content (up to 13%) in the injection interval of the target formation (i.e. the Wonnerup Member of the Lesueur Formation). We imaged the core samples before flooding to verify the presence of kaolinite at the pore-scale using scanning electron microscopy (SEM). We also examined the pore network of the core plugs before and after the core-flooding experiments using Nuclear Magnetic Resonance (NMR). Moreover, to gain a better understanding of any kaolinite fines migration, we delineated surface force using two models based on Derjaguin-Landau-Verwey-Overbeek (denoted by DLVO) theory coupled hydrodynamic force: (1) sphere/flat model representing interaction between kaolinite/quartz, and (2) flat/flat model representing interaction between kaolinite/kaolinite. Our core-flooding experimental results showed that CO 2 /brine injection triggered moderate to significant reduction in the permeability of the core samples with a negligible porosity change. NMR measurements supported the core-flooding results, suggesting that the relatively large pores disappeared in favour of a higher proportion of the medium to small pores after flooding. The DLVO calculations showed that some kaolinite particles probably lifted off and detached from neighbouring kaolinite particles rather than quartz grains. Moreover, the modelling results showed that the kaolinite fines migration would not occur under normal reservoir multiphase flow conditions. This is not because of the low hydrodynamic force. It is rather because the geometries of the particles dominate their interplay. Finally and overall, both of the experimental and analytical modelling results point to the fines migration to be the most likely cause of the permeability impairment observed during core-flooding experiments.

58 GEOSCIENCES↗

Illuminating the geology: Post-injection reservoir characterisation of the CO2CRC Otway site

Proper site characterisation is essential in the planning stages of a CO 2 storage project; but we can also learn a good deal about the reservoir once the injection is underway or has been completed. During CO2CRC Otway Project Stage 2C, sources of valuable information about storage performance have been generated as a consequence of the staged injection of 15,000 t of CO 2 rich gas, as well as observations from time-lapse seismic surveys and well monitoring data. Now that injection has ceased for Stage 2C, the geological model is compared against field observations for the period spanning injection and 23 months after injection ended. The post-injection reservoir characterisation has proven critical to refine the static and dynamic models for future field development and added assurance about the long-term stabilisation of the CO 2 plume. The south-eastern progress of plume development, as seen on the time-lapse seismic data, has led to a review of the structural interpretation and horizon-fault geometry represented in the models. The developing plume has illuminated the extent of splay faults previously unresolved on the baseline seismic data. Saturation profiles interpreted from pulsed-neutron logs at the injection and observation wells show a preference for higher saturations occurring in high permeability distributary channels penetrated by each of the wells. This has reduced the uncertainty in predicting connectivity of this facies between the wells. The pressure data from numerous injection events has been used to refine the characterisation of the average horizontal permeability of the reservoir zone, and the vertical permeability of the intra-formational seal. Furthermore, it has been used to infer near-field bounding conditions of the interior splay fault, which in turn improves our understanding of containment at the site.

58 GEOSCIENCES↗

Screening improved recovery methods in tight-oil formations by injecting and producing through fractures

Tight-oil reservoirs exhibit two characteristic behaviors that limit potential for improved recovery: (i) limited fluid movement from the unfractured matrix limits the potential to sweep additional oil towards the production wells with injection of a displacing fluid, (ii) the wettability of these reservoirs tend to be oil-wet which holds oil in relatively smaller pores, as compared to gas or water, making it difficult to mobilize that trapped oil. Primary oil production from these formations can decline to half of initial rates in the first year due to low permeability in the unfractured reservoir matrix, and a large amount of unrecovered oil remains in smaller pores that is not able to move out. To address these challenges, this study investigates the potential to improve oil recovery from tight-oil reservoirs by a method that includes injecting a fluid into the fractured reservoir to produce hydrocarbons from adjacent fractures intersecting the same wellbore. The injection and production through fractures has a potential economic advantage over huff-n-puff scheme such that there is no lag-period between injection and production. We compare the estimates of incremental oil recovery obtained by injecting water, immiscible CO 2 , and surfactant over the oil recovered by primary depletion (with no injection). The results suggest that injection of fluids may not always improve recovery from tight-oil reservoirs, especially in a heterogeneous reservoir (having different rock types) whose average matrix permeability is lower than 0.01 mD. In cases where recovery is improved over primary depletion, water flood and surfactant flood perform almost equally well with no noticeable difference between the two. Although, surfactant results in favorable fluid properties to mobilize oil, the reason surfactant did not perform well in tight-oil formation studied here is because the unswept oil is inaccessible due to small permeability, and not because of high capillary pressure.

42 ENGINEERING↗

Deuterium permeation and retention in 316L Stainless Steel Manufactured by Laser Powder Bed Fusion

Deployment of additively manufactured materials into nuclear energy systems requires investigation of the full range of the unique environmental effects on these materials. Hydrogen isotopes are common gaseous species in nuclear reactors and exhibit ample high mobility in most materials. While hydrogen isotopes mobility in wrought stainless steel is well understood, this property is not thoroughly studied for its additively manufactured variants. In this study, we investigated the deuterium permeation and retention in 316L stainless steel manufactured by laser powder bed fusion. The results showed that the deuterium permeability in the as-built additively manufactured 316L stainless steel (AM SS316L) is greater than that of the reference wrought 316L stainless steel by a factor of 2.8. However, the stress-relieved and solution-annealed AM SS316L samples exhibit lower deuterium permeability in comparison with the as-built condition. Following the solution annealing, the deuterium permeability of AM SS316L is comparable with that of the reference wrought SS316L. Deuterium retention in the as-built AM SS316L is 45% higher than that of the wrought 316L stainless steel and slightly higher than that of the two thermally annealed AM SS316L materials. Finally, transmission electron microscopy and positron annihilation lifetime spectroscopy were used to obtain microstructural information used to determine deuterium permeation and retention behavior in the studied materials.

36 MATERIALS SCIENCE↗

Pressure core analysis of geomechanical and fluid flow properties of seals associated with gas hydrate-bearing reservoirs in the Krishna-Godavari Basin, offshore India

Physical properties of the sediment directly overlying a gas hydrate reservoir provide important controls on the effectiveness of depressurizing that reservoir to extract methane from gas hydrate as an energy resource. The permeability of overlying sediment determines if a gas hydrate reservoir’s upper contact will provide an effective seal that enables efficient reservoir depressurization. Compressibility, stiffness and strength indicate how overlying sediment will deform as the in situ stress changes during production, providing engineering data for well designs. Assessing these properties requires minimally-disturbed sediment. India’s National Gas Hydrates Program Expedition 2 (NGHP-02) provided an opportunity to study these seal sediment properties, reducing disturbance from gas exsolution and bubble growth by collecting a pressure core from the seal sediment just above the primary gas hydrate reservoir at Site NGHP-02-08 in Area C of the Krishna-Godavari Basin. The effective stress chamber (ESC) and the direct shear chamber (DSC) devices in the suite of Pressure Core Characterization Tools (PCCTs) were used to measure permeability, compressibility, stiffness and shear strength at the in situ vertical stress. Geotechnical properties of the predominantly fine-grained seal layer at in situ vertical stress are in typical clay sediment ranges, with low measured permeability (0.02 mD), high compressibility (C c = 0.26 – 0.33) and low shear strength (404 kPa). Though pressure and temperature were maintained throughout the collection and measurement process to stabilize gas hydrate, the lack of effective stress in the pressure core storage chamber and the chamber pressurization with methane-free water caused core expansion and gas hydrate in a thin coarser-grained layer to dissolve. The PCCTs can reapply in situ stress with incremental loading steps during a consolidation test to account for sediment compaction. Lastly, gas hydrate dissolution can be limited by storing cores just above freezing temperatures, and by using solid spacers to reduce the storage chamber’s free volume.

09 BIOMASS FUELS↗

Numerical simulations of depressurization-induced gas production from an interbedded turbidite gas hydrate-bearing sedimentary section in the offshore India: Site NGHP-02-16 (Area-B)

The recent National Gas Hydrate Program Expedition 02 (NGHP-02) identified the existence of gas hydrate-bearing sand reservoirs at a number of sites in the offshore of India including Site NGHP-02-16 in Area-B of the Krishna-Godavari Basin. The architecture of that gas hydrate accumulation is characterized by thin, gas hydrate-bearing, high quality sand layers interbedded with mud layers within a turbidite sedimentary interval. The lowest gas hydrate-bearing layer contacting a thinly-interbedded saline aquifer designates the base of the gas hydrate stability zone (BGHSZ). The proximity of the BGHSZ and the average temperature around 20 °C make the reservoir a favorable target for hydrate destabilization by means of the depressurization method. The results of the reservoir simulations indicate high gas production potential from this marine gas hydrate deposit with manageable concomitant water production using a well completion design that hydraulically isolates layers with water-saturated sands. Using a detailed geological input model, the predicted cumulative gas rates reach ~3.1 × 10 4 m 3 /day (~1.1 MMscf/day) after 90 days of continuous depressurization and demonstrate sustained production rates ~3.0 × 10 4 m 3 /day (~1.0 MMscf/day) after 5 years of production. The interbedded nature of this gas hydrate occurrence promotes the development of horizontal dissociation interfaces between gas hydrate-bearing sand and mud layers. As a result, non-uniform gas production along the horizontal interfaces becomes a primary determinant of reservoir performance. Simulation cases have been executed to determine the impact of the uncertainty in in situ reservoir permeability and the manner in which intrinsic permeability dynamically changes during dissociation in response to the imposed effective stress increase. Here, the cases based on low initial effective permeability and high sensitivity of compaction to stress result in the least favorable production predictions.

58 GEOSCIENCES↗

Effect of composition and nanostructure on CO2/N-2 transport properties of supported alkyl-imidazolium block copolymer membranes

Polymerized room-temperature ionic liquids (poly(RTIL)s) have garnered attention as new and interesting membrane materials for CO2/light gas separations because they combine the high CO2 affinity and thermal and chemical stability of RTILs, with the physical and mechanical properties of polymeric materials. Our group recently synthesized a new type of block copolymer (BCP) combining an imidazolium-based poly(RTIL) and an alkyl non-ionic polymer. These alkyl-b-ionic BCPs phase-separate into ordered nanostructures. Prior work investigating gas transport through phase-separated BCPs is very limited, and none has included RTIL-based BCP systems. However it has been shown that nanoscale phase-separation could facilitate gas transport via nanostructure orientation control or phase connectivity improvement. We have successfully made defect-free, thin-film composite membranes with these novel alkyl-imidazolium BCPs as a 3-20 mu m thick top layer, and determined their CO2/N-2 separation properties via single-gas permeability measurements and selectivity calculations. These new BCP materials were found to have distinct advantages over the analogous physical blends of the parent homopolymers with respect to membrane fabrication. The composition of the BCP top layer, which is directly connected to the type of nanostructure formed, was found to have a significant effect on CO2 permeability (i.e., it can increase CO2 permeability by two orders of magnitude up to an observed value of 9300 barrer). This improvement is mainly due to a large increase in the diffusion coefficient in the ordered nanostructures compared to amorphous BCP materials. (C) 2012 Elsevier B.V. All rights reserved.

Nguyen, PT↗

Impact of tuning CO 2 -philicity in polydimethylsiloxane-based membranes for carbon dioxide separation

Amidoxime-functionalized polydimethylsiloxane (AO-PDMSPNB) membranes with various amidoxime compositions were synthesized via ring-opening metathesis polymerization followed by post-polymerization modification. Compared to other previously reported PDMS-based membranes, the amidoxime-functionalized membranes show enhanced CO 2 permeability and CO 2 /N 2 selectivity. The overall gas separation performance (CO 2 permeability 6800 Barrer; CO 2 /N 2 selectivity 19) of the highest performing membrane exceeds the Robeson upper bound line, and the excellent permeability of the copolymer itself provides great potential for real world applications where huge volumes of gases are separated. This study details how tuning the CO 2 -philicity within rubbery polymer matrices influences gas transport properties. Key parameters for tuning gas transport properties are discussed, and the experimental results show good consistency with theoretical calculations. Finally, this study provides a roadmap to enhancing gas separation performance in rubbery polymers by tuning gas solubility selectivity.

54 ENVIRONMENTAL SCIENCES↗

Maximizing selectivity: An analysis of isoporous membranes

Membranes are compelling candidates for many separation-based industrial processes. However, all synthetic membranes are subject to well-recognized permeability-selectivity trade-offs that hinder their use in advanced applications. Having uniform nanoscale pore size, isoporous nanofiltration and ultrafiltration membranes have attracted wide research interest. However, quantitative analysis of isoporous membrane performance is lacking - particularly at module and system-level scales. In this study, an analytical model is built to investigate how membrane pore-size distribution affects the solute separation efficiency (i.e., rejection and selectivity). The model accounts for convective hindrance as well as concentration polarization and explores effects on separation from the solute-to-pore-size ratio and percent recovery (i.e., fraction of feed flow that passes through the membrane). At the module level, our analysis suggests that a notably sharper rejection vs. solute size curve can be obtained as the pore-size distribution becomes narrower. Additionally, as the recovery increases, the rejection of a solute is maintained at a high level using isoporous membranes while the rejection drops rapidly for membranes that possess a disperse pore-size distribution. Furthermore, in the separation of mixed solutes, isoporous membranes achieve a large selectivity with a modest loss of permeability. Overall, this study elaborates the unique role that isoporous membranes play within the permeability-selectivity trade-off relations and identifies the most exciting opportunities for their future applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗