Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Motor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Motorette Thermal Performance Testing and Modeling for an Electric Motor with Additively Manufactured Hollow Conductors with Integrated Heat Pipes

This paper discusses the design, build and test of a motorette to characterize the thermal performance of an additively manufactured coil integrated with heat pipes. The motorette is powered using a variable frequency AC power supply and cooled through two independent cooling systems. The first cooling system cools the stator core using forced convection of air flowing over a finned heat sink mounted on the stator outer diameter. The second cooling system cools the heat pipes using forced convection of 50-50 water ethylene glycol (WEG) mixture flowing through condenser chambers. A 3D thermal FEA model of the setup is built and heat transfer coefficients (HTC) of convective boundaries are computed using coolant flow rates from test data and empirical equations. Temperature at locations on the coil and heat sink are recorded and compared to thermal model predicted values. A maximum temperature error of 22.7% occurs at 180ARMS and 800 Hz operating point for the AM dual coil. The thermal model provides higher temperatures compared to test results and hence it is on the conservative side but in general, there is good correlation between test and model results. Lastly, opportunities for improvement to both test data measurement and 3D thermal FEA modeling are discussed.

additive manufacturing↗
DOE OSTI2025

Spike-Free Adaptive Sliding Mode Control: Application to Permanent Magnet Synchronous Motors

A new methodology for adaptive sliding mode control (ASMC) has been widely used to improve the control performance in various systems. This method exhibits several advantages, including low sliding mode control (SMC) chattering, no knowledge of the system disturbance bound, and no overestimation of the control gain. Despite its advantages, this method can be hampered by the spike phenomenon, slow control gain convergence, and difficulty in achieving optimal performance under varying disturbances. Consequently, this article proposes a spike-free ASMC method with a disturbance observer (DOB) to address these problems. Previous ASMC methods have been analyzed via simulations to verify the aforementioned problems. Here, this analysis highlights the need for disturbance compensation and improvements in the SMC gain adaptation law. Therefore, a DOB is designed to mitigate the spike phenomenon by compensating for disturbances. Subsequently, an SMC gain adaptation law based on disturbance error estimation is designed to eliminate the spike phenomenon completely. The proposed adaptation law makes the SMC gain to converge to a slightly higher value than the disturbance estimation error. Consequently, the proposed method not only eliminates the spike phenomenon, but also ensures optimal performance under varying disturbances. The performance of the proposed method is experimen tally validated through a comparative study.

42 ENGINEERING↗
DOE OSTI2024

In-cylinder spray evolution in a motored central-injection gasoline engine: Imaging and simulating the effects of flash-boiling and intake crossflow

Accurate predictions of fuel spray behavior and mixture formation in simulations of direct-injection spark-ignition (DISI) engines are fundamental to ensure proper description of all subsequent processes including ignition, combustion, and emissions. In this work, the spray evolution in a single-cylinder optical DISI engine was studied experimentally and numerically with the goal of enabling predictive computational fluid dynamics (CFD) modeling of in-cylinder sprays. The authors explored a wide range of operating conditions characterized by several fuel injection temperatures and engine speeds, using a well-characterized nine-component gasoline surrogate known as PACE-20. The effect of flash boiling and intake crossflow on the spray is discussed, with a focus on evaluating the ability of the spray models to capture highly transient spray behavior. In the experiments, the fuel temperature was varied between 20°C and 80°C, allowing for non-flash- to flash-boiling transition to emerge with enhanced flashing intensity at the highest temperatures. Spray collapse resulted in vapor-rich regions, owing to the locally lower inertia of the fluid. Varying the engine speed from 650 to 1950 rpm promoted increasingly more turbulent in-cylinder crossflow which interacted with the spray during the injection event and resulted in enhanced spray dispersion. The CFD model was able to capture the spray morphology transition at different fuel temperatures and engine speeds adequately. Further, it is shown that the spray breakup model could capture the transitional spray behavior induced by flash boiling atomization and intake flow via proper initialization of the spray cone angle and calibration of the spray models’ constants.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Abstract for CRADA between the National Energy Technology Laboratory and General Motors (AGMT-0876)

Lightweight aluminum shape castings have widespread applications for structural components in the automotive, aerospace, and general engineering industries because of their excellent castability, corrosion resistance, and particularly high strength-to-weight ratio in the heat-treated condition. In the automotive industry, cast aluminum alloys have been increasingly used to replace cast iron and steel in vehicle applications such as engine blocks, cylinder heads, intake manifolds, brackets, housings, chassis, transmission parts, and suspension systems to reduce mass. As many of the aluminum shape castings used in automobiles involve cyclic loading, fatigue properties of the castings are critical to their success. The increasing use of lightweight aluminum cast components in critical structures thus requires improved integrity, with more reliable and quantifiable performance. The objective of this project is to demonstrate and further develop GM’s patent-pending, novel casting process, “Pressure-Assistant Precision Sand Casting (PAPSC) for producing flawless cast aluminum cylinder heads with minimum manufacturing and energy costs”. The approach is to leverage NETL’s experience in producing high-quality metal castings through various microstructure control and defect elimination technologies as well as comprehensive quantification of microstructure characteristics and mechanical properties. A baseline (production) alloy together with the melt treatment will be initially evaluated with the new PAPSC process to develop and validate the process window for producing flawless cast aluminum heads.

36 MATERIALS SCIENCE↗