Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Report on Skylab -M552 samples

Results of examining the M522 specimens are reported. The visual examination, location of sectioning planes, and microstructure are described. It is concluded that no specific effects of the zero gravity processing can be identified.

Source record↗

Eutectic solidification

The possibilities of using the low-gravity space environment for the processing of directionally solidified materials in order to remove the limitations imposed by the L-g earth environment have led to a careful evaluation of the directional solidification process and the results commonly obtained. Defects in the regularity of the microstructure have been identified as one of the most important areas where present processing technology needs to be improved. One-g environment material processing must also be carefully characterized before it can be determined if zero-g processing will produce significant benefits in eutectic and off-eutectic solidification. It is suggested that a combination of experimental and analytical thermal studies will be required to optimize the solidification process in order to minimize the structural defects which occur due to present processing techniques.

Douglas, F. C.↗

Grain boundary mobility in anion doped MgO

Certain anions OH(-), F(-) and Gl(-) are shown to enhance grain growth in MgO. The magnitude of their effect decreases in the order in which the anions are listed and depends on their location (solid-solution, second phase) in the MgO lattice. As most anions exhibit relatively high vapor pressures at sintering temperatures, they retard densification and invariably promote residual porosity. The role of anions on grain growth rates was studied in relation to their effect on pore mobility and pore removal; the atomic process controlling the actual rates was determined from observed kinetics in conjunction with the microstructural features. With respect to controlling mechanisms, the effects of all anions are not the same. OH(-) and F(-) control behavior through creation of a defect structure and a grain boundary liquid phase while Cl(-) promotes matter transport within pores by evaporation-condensation. Studies on an additional anion, S to the minus 2nd power gave results which were no different from undoped MgO, possibly because of evaporative losses during hot pressing. Hence, the effect of sulphur is negligible or undetermined.

Kapadia, C. M.↗

TDNiCr (ni-20Cr-2ThO2) forging studies

Elevated temperature tensile and stress rupture properties were evaluated for forged TDNiCr (Ni-20Cr-2ThO2) and related to thermomechanical history and microstructure. Forging temperature and final annealed condition had pronounced influences on grain size which, in turn, was related to high temperature strength. Tensile strength improved by a factor of 8 as grain size changed from 1 to 150 microns. Stress-rupture strength was improved by a factor of 3 to 5 by a grain size increase from 10 to 1000 microns. Some contributions to the elevated temperature strength of very large grain material may also occur from the development of a strong texture and a preponderance of small twins. Other conditions promoting the improvement of high temperature strength were: an increase of total reduction, forging which continued the metal deformation inherent in the starting material, a low forging speed, and prior deformation by extrusion. The mechanical properties of optimally forged TDNiCr compared favorably to those of high strength sheet developed for space shuttle application.

Filippi, A. M.↗

Estimates of the size of the particles in the rings of Saturn and their cosmogonic implications

Observations are discussed which are consistent with the ring particles having a very high single scattering albedo at radio wavelengths, with multiple scattering effects being important. Comparison of scattering calculations for ice and silicate particles with the radio and radar observations imply a mean particle radius of about 1 cm. The ice bands observed in the near-infrared reflectivity spectra of the rings are formed by scattering within a microstructure on the surface of the ring particles, with the scattering centers being 25 to 125 micrometers in size. The Poynting-Robertson effect has caused a significant spiraling-in of the ring particles, probably resulting in a broadening of the rings. The inferred mean size is consistent with a model in which meteoroid impacts have caused a substantial reduction in the mean particle size from its initial value.

Pollack, J. B.↗

Preparation and metallurgical properties of low gravity processed immiscible materials

Initial experiments conducted during the Apollo 14 mission demonstrated that unique dispersions of immiscible materials could be obtained by processing in a low gravity environment. Subsequently, seven metallic systems have been processed in three NASA facilities: the drop tower at MSFC, the M-512 facility on board a KC-135 aircraft and the M-518 furnace on board Skylab. All couples were solidified from the liquid while in a low gravity environment, with one gravity processed specimens as controls. Metallographic examination demonstrated that the specimens processed in a low gravity environment exhibited a more uniform dispersion and microstructure than the one gravity processed controls.

Reger, J. L.↗

Oxidation behavior of TD-NiCr in a dynamic high temperature environment

The oxidation behavior of TD-NiCr has been studied in static and high-speed flowing air environments at 1100 and 1200 C. It has been found that the stable oxide morphologies formed on the specimens exposed to the static and dynamic environments were markedly different. The faceted crystal morphology characteristic of static oxidation was found to be unstable under high-temperature, high-speed flow conditions and was quickly replaced by a porous NiO 'mushroom' type structure. Also, it was found that the rate of formation of CrO3 from Cr2O3 was greatly enhanced by high gas velocity conditions. The stability of Cr2-O3 was found to be greatly improved by the presence of an outer NiO layer, even though the NiO layer was very porous. An oxidation model is proposed to explain the observed microstructures and overall oxidation behavior of TD-NiCr alloys.

Tenney, D. R.↗

Nedagolla, a remelted iron meteorite

The Nedagolla meteorite was recognized by Axon to be a rare example of an iron which has been preterrestrially reheated to the point of melting. The dendrite secondary arms are spaced 200 microns apart, implying that Nedagolla solidified and cooled at about 0.02 C/sec. The presence of (Fe, Cr)(1-x)S inclusions precipitated during cooling in the interdendritic regions, and evidence of solute redistribution of Ni, Cr, Co, Si, and P are consistent with this cooling rate. Such a rate indicates that Nedagolla cooled very near the surface of its parent 'body'. Secondary microstructural features including the presence of isothermal taenite and minute phosphide precipitates, which have formed from the dissolution of primary phosphide material, indicate a later reheating to about 750 C for a period of several hours.

Miyake, G. T.↗

Radial and directional solidification of metallic systems in space

Investigation of the solidification behavior of spherical specimens of Ni-12 wt % Sn and Ni-1 wt % Ag that froze radially from the surface toward the center and cylindrical specimens of Al-33 wt % Cu eutectic that froze directionally under appropriately selected conditions of thermal gradient at the solid-liquid interface and growth rate. Possible effects of vacuum and low gravity conditions, under which the spherical specimens were processed, on observed nucleation and growth phenomena are discussed. A genetic explanation is given of observed microstructures, and the distributions of alloying elements is discussed. In directionally solidified eutectic specimens a comparison is made between statistically evaluated growth defects in Skylab and in ground specimens.

Katamis, T. Z.↗

High-temperature strength stability of three forms of chemically vapor deposited tungsten

Three types of CVD tungsten (fluoride-produced, chloride-produced, and a layered composite of the two-termed duplex) were evaluated to determine their high-temperature strength and microstructural stability following 5000-hr exposure to temperatures of 1540 and 1700 C. At the highest temperatures investigated (1540 and 1700 C), the tensile strengths of the two basic materials were essentially equal. At lower temperatures, chloride tungsten possessed lower yield strength but higher ultimate strength than fluoride tungsten while the behavior of the duplex material was generally intermediate. Apparent anomalies in high-temperature elongation behavior are explained on the basis of grain boundary cavity formation and recrystallization. The grain size of fluoride tungsten changed only slightly following 5000-h treatment at 1700 C. In contrast, chloride tungsten possessed both poor resistance to grain growth and an accompanying relatively high ductile-brittle transition temperature.

Bryant, W. A.↗

The Tucson meteorite

Tucson is an unusual iron meteorite which contains highly reduced silicate inclusions and elemental silicon and chromium in solution. The metal matrix of Tucson was found to be chemically uniform, suggesting that homogenization has occurred at elevated temperatures. The microstructure of the metal consists of plessite and thin ribbons of kamacite. Nickel and phosphorus concentrations indicate that kamacite nucleated along prior taenite grain boundaries at about 650 C, and grew upon cooling to 500 C. Kamacite growth calculations show that Tucson cooled at about 1 C/1000 yr, a rate which corresponds to a depth of burial at the center of a 15-km-radius parent body or closer to the surface of parent bodies of larger sizes. The shapes of the Tucson irons, and the presence and distribution of silicate inclusions in the Fe-Ni matrix appear to be a result of a solidification process.

Miyake, G. T.↗

Liquid-metal atomization for hot working preforms

Rapid quenching of a liquid metal by atomization or splat cooling overcomes the major limitation of most solidification processes, namely, the segregation of alloying elements, impurities, and constituent phases. The cooling rates of different atomizing processes are related to the dendrite arm spacings and to the microstructure of the atomized powders. The increased solubility limits and the formation of metastable compounds in splat-cooled alloys are discussed. Consolidation of the powders by hot isostatic compaction, hot extrusion, or hot forging and rolling processes yields billets with properties equivalent to or better than those of the wrought alloys. The application of this powder processing technology to high-performance alloys is reviewed.

Grant, N. J.↗

Physical forces influencing Skylab experiments M551, M552, and M553

The forces concerned with metals melting, exothermic brazing, and sphere forming experiments on Skylab 1 mission are reported. The conclusions reached are that no significant practical differences exist between terrestrial and microgravity electron beam melting, and braze gap clearances are far less critical to joining operations in space than on earth. Altered microstructures, increased grain refinement, and the appearance of a single, large interior shrinkage pore were found in the Skylab specimens.

Bourgeois, S. V.↗

Directionally solidified composite systems under evaluation

Various types of high temperature in-situ composites were reviewed and attempts were made to determine which ones offer the most potential for future development. Some of the systems that were investigated according to the ductility of the component phases were categorized. The categories range from ductile-ductile to brittle-brittle. Examples in each category are considered with special emphasis on systems which look attractive for use in gas turbine engines. Data also touch on microstructure, mechanical properties, and process problems.

Ashbrook, R. L.↗

Investigation of solidification in zero-gravity environment: M553 sphere forming experiment. Nickel-silver alloy evaluation

The processing of nickel-silver alloy specimens in space is discussed. Four specimens were melted only partially, while a fifth was melted completely and assumed after solidification a perfectly spherical shape. Growth of the solid was epitaxial on the unmelted material or on the retaining sting and occurred without undercooling. Solidification was dendritic in all cases with nonequilibrium silver particles forming monotectically between dendrite arms. Substantial loss of silver by evaporation took place. Evaporation of the silver within internal gas cavities on the melt was followed by surface condensation after completion of solidification and cooling, leading to a silver-rich lining in these cavities. The material gave no microstructural evidence of any reduction in liquid convection.

Kattamis, T. Z.↗

Surface recrystallization theory of the wear of copper in liquid methane

Copper was subjected to sliding against 440C in liquid methane. The normal load range was from 1/4 to 2 kilograms, and the sliding velocity range was from 3.1 to 25 meters per second. Over this range of experimental parameters, the wear rate of the copper rider was found to be proportional to the sliding velocity squared and to the normal load. Transmission electron microscopy was used to study the dislocation structure in the copper very near the wear scar surface. It was found that near the wear scar surface, the microstructure was characterized by a fine-cell recrystallized zone in which individual dislocations could be distinguished in the cell walls. The interiors of the cells, about 0.5 micrometer in diameter, were nearly dislocation free. Below the recrystallized layer was a zone that was intensely cold worked by the friction process. With increasing depth, this intensely cold worked zone gradually became indistinguishable from the partially cold worked bulk of the copper, representative of the initial condition of the material.

Bill, R. C.↗

High-purity silica reflecting heat shield development

A high-purity, fused-silica reflecting heat shield for the thermal protection of outer-planet probes was developed. Factors that strongly influence the performance of a silica heat shield were studied. Silica-bonded silica configurations, each prepared by a different technique, were investigated and rated according to its relative merits. Slip-casting was selected as the preferred fabrication method because it produced good reflectivity and good strength, and is relatively easy to scale up for a full-size outer-planet probe. The slips were cast using a variety of different particle sizes: continuous particle-size slips; monodisperse particle-size slips; and blends of monodisperse particle-size slips were studied. In general, smaller particles gave the highest reflectance. The monodisperse slips as well as the blend slips gave a higher reflectance than the continuous particle-size slips. An upgraded and fused natural quartz was used to study the effects of microstructure on reflectance and as the baseline to ascertain the increase in reflectance obtained from using a higher-purity synthetic material.

Congdon, W. M.↗

Microdosimetry and the radiation danger of cosmic rays

The radiation danger of space flights is due primarily to intensive proton fluxes accompanying solar flares and heavy multiple charged ions in galactic cosmic radiation. Evaluation of the biological effect of these kinds of rays is based on calculations of tissue dose, taking into account the formation of secondary radiation in shielding and tissue. The essential role in such calculations is played by the dependence of the factor of quality on linear energy transfer (LET) of these charged particles. Recommendations concerning the dependence of the quality factor on LET are based on radiobiological experiments carried out on many biological systems using various kinds of rays, including heavy ions with energies in the 1-10 Mev/nucleon range. Justification of the results of these experiments, as well as their extrapolation to other energies, requires development of a model description of the radiation effect of charged particles on biological microstructures.

Gunter, K.↗