Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Nondestructive characterization of polycrystalline 3D microstructure with time-domain Brillouin scattering

In this paper, we employ gigahertz frequency ultrasonic waves to non-invasively image grain microstructure in polycrystalline ceria, an important electrolyte material for solid oxide fuel cells. This technique, termed time domain Brillouin scattering (TDBS), is a pump-probe technique that launches and monitors ultrasonics waves as they propagate from the surface into the depth of a sample. We demonstrate the capability of TDBS to image surface and subsurface grain structure by measuring mode and depth dependent velocity of the ultrasonic wave. A neural network tool is adopted to determine grain orientation from measured velocities. The TDBS results compare closely with electron backscatter diffraction (EBSD) measurements. This work expands the application of picosecond ultrasonics to three-dimensional imaging and offers a new route for the nondestructive microstructure characterization and in situ examination of polycrystalline materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure investigations of hcp phase CoPt thin films with high coercivity

CoPt films have been grown in the past with a high anisotropy in L1{sub 1} or L1{sub 0} phase, and a high coercivity is observed only in L1{sub 0} CoPt films. Recently, we have grown CoPt films which exhibited a high coercivity without exhibiting an ordered phase. In this study, high resolution transmission electron microscopy (HRTEM) investigations have been carried out to understand the strong thickness and deposition pressure dependent magnetic properties. HRTEM studies revealed the formation of an initial growth layer in a metastable hexagonal (hcp) CoPt with high anisotropy. This phase is believed to be aided by the heteroepitaxial growth on Ru as well as the formation of Ru-doped CoPt phase. As the films grew thicker, transformation from hcp phase to an energetically favourable face-centered cubic (fcc) phase was observed. Stacking faults were found predominantly at the hcp-fcc transformation region of the CoPt film. The higher coercivity of thinner CoPt film is attributed to relatively less fcc fraction, less stacking faults, and to the isolated grain structure of these films compared to the thicker films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Iridescence from Total Internal Reflection at 3D Microscale Interfaces: Mechanistic Insights and Spectral Analysis

An experimental investigation and the optical modeling of the structural coloration produced from total internal reflection interference within 3D microstructures are described. Ray-tracing simulations coupled with color visualization and spectral analysis techniques are used to model, examine, and rationalize the iridescence generated for a range of microgeometries, including hemicylinders and truncated hemispheres, under varying illumination conditions. An approach to deconstruct the observed iridescence and complex far-field spectral features into its elementary components and systematically link them to ray trajectories that emanate from the illuminated microstructures is demonstrated. The results are compared with experiments, wherein microstructures are fabricated with methods such as chemical etching, multiphoton lithography, and grayscale lithography. Microstructure arrays patterned on surfaces with varying orientation and size lead to unique color-traveling optical effects and highlight opportunities for how total internal reflection interference can be used to create customizable reflective iridescence. The findings herein provide a robust conceptual framework for rationalizing this multibounce interference mechanism and establish approaches for characterizing and tailoring the optical and iridescent properties of microstructured surfaces.

36 MATERIALS SCIENCE↗

Y{sub 2}O{sub 3}:Eu{sup 3+} microstructures: Hydrothermal synthesis and photoluminescence properties

Hexagonal microprisms of yttrium hydroxide (Y(OH){sub 3}) with tuned diameter and height have been successfully prepared for the first time via a facile hydrothermal process using sodium citrate as the shape modifying agent. Y(OH){sub 3} microspheres with diameter of ca. 2.5 {mu}m and microtubes with an average length about 13 {mu}m, outer diameter about 3 {mu}m and tube thickness about 800 nm were also obtained in current reaction systems. The possible formation mechanism for the Y(OH){sub 3} microstructures was briefly proposed. Y{sub 2}O{sub 3}:Eu{sup 3+} (5%) microstructures with similar morphologies was obtained after thermal treatment of the as-prepared Y(OH){sub 3}:Eu{sup 3+} microstructures at 700 {sup o}C for 4 h. Results show that the relative emission intensity of the Y{sub 2}O{sub 3}:Eu{sup 3+} microprisms is about 8 times as those of the Y{sub 2}O{sub 3}:Eu{sup 3+} microtubes and microspheres under excitation of 259 nm ultraviolet light. The products were characterized by XRD, SEM, and EDS.

36 MATERIALS SCIENCE↗

Phase transformations in steels: Processing, microstructure, and performance

In this study, contemporary steel research is revealing new processing avenues to tailor microstructure and properties that, until recently, were only imaginable. Much of the technological versatility facilitating this development is provided by the understanding and utilization of the complex phase transformation sequences available in ferrous alloys. Today we have the opportunity to explore the diverse phenomena displayed by steels with specialized analytical and experimental tools. Advances in multi-scale characterization techniques provide a fresh perspective into microstructural relationships at the macro- and micro-scale, enabling a fundamental understanding of the role of phase transformations during processing and subsequent deformation.

36 MATERIALS SCIENCE↗

Effect of 316 stainless steel powder processing conditions on microstructure

One parameter that has both economic and performance effects in the manufacturing of steel parts is the powder feedstock used. 316 L steel powder can be produced through water atomization or gas atomization, where both the powder size and the atomization process determine the cost of powder feedstock. Gas atomized powder is spherical and has a lower oxygen content than water atomized powder, making it the preferred choice for performance, but comes at a higher financial cost. Here, in this study, various 316 L powder batches are characterized to understand physical properties and microstructural variations. Density and flowability were determined using gas pycnometry and Hall flow tests. Powder morphology and porosity were qualitatively analyzed via optical microscopy and scanning electron microscopy, Finally, transmission electron microscopy was used to determine changes in phases present. Spherical gas atomized powder of 30–100 μm contained Mn$-$Si rich oxides both on the surface and within the matrix. Meanwhile, irregular water atomized powder 30 μm in diameter contained silicon oxides without manganese. All powder particles contained a nickel rich cellular structure which was shown to support the formation of additional phases. While literature has observed general microstructural features across 316 L powder particles, transmission electron microscopy (TEM) in this study has identified variations in precipitation and cell structures. Information regarding morphology, flowability, density, and phase distributions can be applied to understand variations in part consolidation, which will in turn show which powder aspects are significant for production.

Chemical segregation↗

The Application of Canned Deformation to a Hard-Deformed Spray-Deposited Al-Zn-Mg-Cu Alloy

A wide variety of industrial applications require Al-Zn-Mg-Cu alloys with high strength and ductility. However, Zn-rich Al-Zn-Mg-Cu alloys prepared by rapid solidification methods usually show excellent strength but poor formability, which restricts their wide application in complex forming. In this study, we developed a new deformation method for the spray-deposited Zn-rich Al-Zn-Mg-Cu alloy to avoid crack formation and achieve isotropic properties. The microstructure evolution and crystallographic textures were analyzed and compared with the results of a normal deformation process. Crack-free forgings with the ultimate tensile strength (UTS), yield strength (YS) and elongation of 727 ± 5 MPa, 690 ± 3 MPa, 5.0 ± 0.7% along the radial direction and 735 ± 2 MPa, 693 ± 3 MPa, 6.3 ± 0.2% along the tangential direction were finally obtained. The improvement in the mechanical properties can be attributed to the larger amount of subgrains and substructures generated in the canned deformed alloy. The results of this study show excellent advantages and potential application prospects of the canned deformation to hard-deformed Al-Zn-Mg-Cu alloys.

36 MATERIALS SCIENCE↗

Numerical Simulations of One-dimensional Microstructure Dynamics

Results of numerical simulations of one-dimensional wave propagation in microstructured solids are presented and compared with the corresponding results of wave propagation in given layered media. A linear microstructure model based on Mindlin theory is adopted and represented in the framework of the internal variable theory. Fully coupled systems of equations for macro-motion and microstructure evolution are rewritten in the form of conservation laws. A modification of wave propagation algorithm is used for numerical calculations. It is shown how the initial microstructure model can be improved in order to match the results obtained by both approaches.

36 MATERIALS SCIENCE↗

Assessment of semi-empirical potentials for the U-Si system

Accident tolerant fuels (ATF) are being developed in response to the Fukushima Daiichi accident in Japan. One of the options being pursued is U-Si fuels, such as the U 3 Si 2 and U 3 Si 5 compounds, which benefit from high thermal conductivity (metallic) compared to the UO2 fuel (semi-conductor) used in current Light Water Reactors (LWRs). The U-Si fuels also have higher fissile density. In order to perform meaningful engineering scale nuclear fuel performance simulations, the material properties of the fuel, including the response to irradiation environments, must be known. Unfortunately, the data available for U-Si fuels are rather limited, in particular for the temperature range where LWRs would operate. The ATF HIP is using multi-scale modeling and simulations to address this knowledge gap. Even though Density Functional Theory (DFT) calculations can provide useful answers to a subset of problems, they are computationally too costly for many others, including properties governing microstructure evolution and irradiation effects. For the latter, semi-empirical potentials are typically used. Unfortunately, there is currently no potential for the U-Si system. In this brief report we present initial results from the development of a U-Si semi-empirical potential based on the Modified Embedded Atom Method (MEAM). The potential should reproduce relevant parts of the U-Si phase diagram as well as defect properties important in irradiation environments. This work also serves as an assessment of the general challenges associated with the U-Si system, which will be valuable for the efforts to develop a U-Si Tersoff potential undertaken by Idaho National Laboratory (also part of the ATF HIP). Going forward the main potential development activity will reside at INL and the work presented here is meant to provide input data and guidelines for that activity. The main focus of our work is on the U 3 Si 2 and U3Si 5 compounds, because they are the main nuclear fuel candidates. U 3 Si 5 is derived from USi 2 in the AlB 2 structure by creating 1/6 vacant sites on Si sublattice. The ordering of these vacancies will not be studied in any detail here.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Limiting Retained Austenite Decomposition in Quenched and Tempered Steels: Influences of Rapid Tempering and Silicon

Tempering reactions are critical to microstructure and property control in martensitic steels. Here, retained austenite decomposition and cementite precipitation are monitored using Mössbauer spectroscopy in 4340 and 300-M steel under conventional and rapid tempering conditions. Tempering times are compared at a constant tempered hardness by increasing tempering temperatures associated with short time conditions to achieve equivalent matrix softening to that of longer tempering times. Time-temperature combinations that provide equivalent tempered hardness generated microstructures with similar dislocation densities and cementite precipitation fractions; these mechanisms are controlled by self-diffusion. However, systematic differences in retained austenite content were observed at a given degree of softening, where shorter tempering times exhibited higher levels of retained austenite compared to more conventional conditions. At low temperatures, the differences in retained austenite preservation between explored time-temperature conditions are attributed to corresponding differences in carbon diffusion distance (in austenite), the controlling diffusional process of retained austenite decomposition. At higher temperatures, retained austenite decomposition exhibits C-curve kinetic behavior in 4340. Thus, reduced thermodynamic driving force for cementite and ferrite formation at higher temperature is believed to play a role in restricting retained austenite decomposition within some short-time, high temperature tempering regimes. The addition of silicon pushes cementite precipitation and retained austenite decomposition to higher temperatures, although retained austenite decomposition is suppressed to a greater extent than cementite precipitation. Potential is illustrated for coupling rapid tempering with silicon alloying to produce appreciably tempered martensite (~490 HV) with relatively less retained austenite decomposition compared to conventional tempering conditions.

36 MATERIALS SCIENCE↗

Microstructure Alignment Effects from Engineered Cooling during Additive Manufacturing of Alnico Magnets from Prealloyed Powder

Alnico is a rare-earth free; permanent magnet (PM) which maintains its saturation magnetization while at temperatures up to 550°C but lacks the coercivity and energy product needed for a wide range of demanding applications. With an optimal set of processing and manufacturing techniques, Alnico could replace Dy-free Nd-Fe-B magnets in certain applications if the microstructure is textured in a $\langle$001$\rangle$ direction. Additive manufacturing (AM) of near-net-shape magnets may provide such texture. To investigate the possibility, directed-energy deposition (DED) in conjunction with an actively cooled substrate was used to build samples with a compositionally modified, gas-atomized, Alnico 8 alloy. The resulting samples were solutionized and quenched, followed by magnetic annealing and a heat treatment. Magnetic properties and microstructures are compared to previous work.

36 MATERIALS SCIENCE↗

Phase-Field Modeling of Nugget Zone for a AZ31-Mg-Alloy Friction Stir Weld

This work presents simulation of microstructure evolution in the nugget zone (NZ) of a AZ31-Mg-alloy friction stir weld. The process parameters (tool geometrical characteristics, rotational speed, travel speed, applied load) have been correlated with the resulting microstructural features in the NZ of the weld (grain size and population) with the aid of the MICRESS software, which provides the ability to simulate both nucleation and grain growth during dynamic recrystallization phenomena evolving in the NZ during the weld thermal cycle. The input parameters of the developed model include the tool geometry, the welding conditions as well as the recrystallization energy, the grain boundary mobility and specific material properties. NZ microstructure obtained by simulation shows good agreement with experimental measurements for both grain population and size.

36 MATERIALS SCIENCE↗

Mechanical properties and microscale changes of geopolymer concrete and Portland cement concrete containing micro-encapsulated phase change materials

The effect of micro-encapsulated phase change materials (MPCM) in solid and liquid states on the mechanical properties and microstructure of geopolymer and Portland cement concretes is investigated. Geopolymer concrete (GPC) and Portland cement concrete (PCC) containing different amounts of MPCM were prepared and cured at both 20 °C and 40 °C. The results revealed that the compressive strength of both GPC and PCC decreases with the addition of MPCM. Whether the PCM is in solid (20 °C) or liquid (40 °C) state did not significantly affect the mechanical properties of GPC, while melting the PCM was found to reduce the strength of PCC. X-ray tomography imaging was utilized to examine the effect of MPCM on the porosity of the samples. SEM imaging reveals that air gaps are formed between the microcapsules and the surrounding concrete matrix.

36 MATERIALS SCIENCE↗

Leveraging the digital thread for physics-based prediction of microstructure heterogeneity in additively manufactured parts

A major limitation of additive manufacturing (AM) processes is that local conditions of material deposition frequently lead to unintentional heterogeneities in microstructure and properties within a single component, despite nominally uniform process conditions. Up to now, there has been no way to a priori determine the distribution of these heterogeneities, requiring expensive trial-and-error approaches to fabrication, testing, and characterization. Here, a physics-based framework for creating a digital representation of the laser powder bed fusion (PBF) process is proposed to predict the variation in solidification behavior that leads to heterogeneous microstructures in an as-built part. By leveraging in situ process data stored in the part’s digital thread, the scan path and process parameters were input into a heat transfer model which predicted solidification data at the melt pool scale. A two-step unsupervised clustering algorithm was used to first cluster the local solidification conditions (12.5µm 3 voxels) and then to cluster the regional behavior on the scale of multiple scan passes and print layers (250µm 3 super-voxels). This process was used to identify regions with similar solidification characteristics for multiple locations in a Stainless Steel 316-L component. The corresponding as-built part was sectioned and characterized using electron backscatter diffraction (EBSD). Quantitative analysis of the pole figures confirmed that the predicted regions of heterogeneity in the solidification conditions corresponded with differences in the observed microstructure. In conclusion, this work shows a viable path for estimating the microstructural heterogeneity for additively manufactured parts to either limit microstructural variation throughout a part or to enable functionality-based variation of the microstructure.

36 MATERIALS SCIENCE↗

Low-Cost, Efficient and Durable High Temperature Wireless Sensors by Direct Write Additive Manufacturing for Application in Fossil Energy Systems

In-situ monitoring of physical parameters in fossil energy (FE) systems is challenging because of their high operating temperatures and oxidizing environments. This research aims utilize Aerosol Jet (AJ) nanoparticle printing, an advanced additive manufacturing method, to fabricate high temperature sensors for FE applications. Sensor films were fabricated by the AJ printing method with an excellent control over film microstructure and properties, in addition to creating less waste. Printing of six different materials, namely, silver (Ag), nickel (Ni), nickel-chromium (NiCr) alloy, copper (Cu), copper-nickel (CuNi), and carbon nanotubes (CNTs) was carried out for their evaluation of as sensor films. The films were then characterized using impedance spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), x-ray diffraction (XRD), and x-ray photoelectron spectroscopy (XPS). Film microstructure was correlated with the sensor electrical and mechanical behavior at different temperatures (24-500 °C) and frequencies (0.02 - 300 kHz). This knowledge was then used to fabricate, test, and characterize strain and temperature sensors for high temperature applications. The strain sensors were shown to have a very low thermal strain up to 500 °C and a 57% higher gauge factor compared to the commercially available counterparts. This enhance performance was attributed to the inherent porosity in the sensor films that allowed the films to exhibit a metamaterial-like behavior when deformed. The AJ printed temperature sensors were shown to have the highest Seebeck coefficient amongst all the film-based temperature sensors. In addition, fundamental aspects of crystal structure and phase transformations in Ba(Fe0.7Ta0.3)O3-δ (BFTO), a high temperature sensor material, was investigated along with 3D printed antennas that can transmit sensor signals at high temperatures. Two PhD students, one from first generation college-going underrepresented minority community (URM), two postdoctoral fellows, and several masters and undergraduate students were supported by this award. This work opens up the possibility of realizing low-cost high-performance sensor devices using advanced manufacturing techniques for high temperature FE applications.

20 FOSSIL-FUELED POWER PLANTS↗

Microstructure and high temperature tensile properties of 316L fabricated by laser powder-bed fusion

316L stainless steel fabricated by laser powder-bed fusion (LPBF) has attracted significant attention due to a unique combination of strength and ductility at room temperature. Understanding of high temperature tensile properties of LPBF fabricated 316L is, however, limited. In the present investigation, tensile testing was conducted at 20–700ºC on LPBF 316L in as printed condition and after annealing for 5 h at 500–800ºC. Room temperature data confirmed the excellent ductility of the LPBF-processed 316L steel due to the cellular structure with high dislocation density. However, a significant decrease in ductility was observed at temperatures above 200ºC. These results are consistent with a change of deformation mechanisms observed in wrought 316L, with twinning playing a key role at room temperature. Finally, microstructure characterization and tensile testing revealed that the cellular structure is stable up to 500ºC, but a decrease of yield strength was observed at temperatures above 600ºC likely due to a decrease in dislocation density via annealing.

36 MATERIALS SCIENCE↗

High Strength, Utilizable Ductility and Electrical Conductivity in Cold Rolled Sheets of Cu-Cr-Zr-Ti Alloy

The microstructure and properties of Cu-0.5Cr-0.03Zr-0.04Ti (wt.%) alloy subjected to cold rolling and aging were investigated using hardness and electrical conductivity measurement, tensile testing, and transmission electron microscopy. Plates subjected to 85% reduction in thickness showed significant improvement in the strength compared to solution treated and aged condition. By proper selection of aging temperature, ductility could be significantly improved without reduction in the strength. Aging of the cold rolled sheet at 420 °C for 1 h yielded an ultimate tensile strength and yield strength of 540 and 460 MPa, respectively. On the other hand, total and uniform elongation was 16 and 12%, respectively, with an electrical conductivity of 65 %IACS. The combination of properties achieved after cold rolling and aging is attributed to the higher dislocation density, ultrafine grains and nano-sized chromium precipitates.

36 MATERIALS SCIENCE↗

Microstructural and mechanical characterization of Al–Zn–Si nanocomposites

In this paper the addition of silicon nanoparticles into Al–Zn alloys to form metallic matrix nanocomposites by mechanical alloying process was investigated. The influence of various process parameters such as milling time and Si concentration in the Al–Zn matrix has an interesting effect on the microstructure and mechanical properties of the synthesized nanocomposites. The microstructural characterization of the nanocomposites was evaluated by transmission electron microscopy and energy dispersive X-ray spectroscopy (TEM–EDXS) and the mechanical properties were measured by nanoindentation and micro-hardness tests. The results showed that during mechanical milling Si is added to the Al–Zn matrix achieving a uniform and homogeneous dispersion. After solidification, it forms small particles of AlZnSi with blocky morphology in interdendritic regions. The nanoindentation profiles showed that the elastic modulus and hardness properties increase with increasing milling time. However, a high concentration of Si (> 1.2 wt.%) results in a saturation of Si in the Al–Zn matrix, which adversely affects the mechanical properties. Thus, it is important to tune the milling time and concentration of Si added to the Al–Zn alloys to control the growth of brittle phases that result in reduction of the mechanical properties of the material. - Highlights: • A novel technique for addition of Si nanocomposites into Al–Zn liquid alloy is reported. • Good dispersion and homogeneity of Si in the Al–Zn matrix are obtained. • Increasing Si content above 1.2 wt.% decreases the mechanical properties of Al–Zn alloy. • The saturation point of Si in 1.2 wt.% differs from Galvalume® composition. • The Al–Zn–1.5Si alloy with addition of nanocomposite shows 5.7 GPa of hardness.

36 MATERIALS SCIENCE↗