Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Lubricants”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Tribocorrosion of stainless steel sliding against graphite in FLiNaK molten salt

The molten salt reactor (MSR) concept recently gained renewed interest in developing Generation IV nuclear reactors. One MSR design uses fluoride molten salts to cool tri-structural isotropic particle fuel encapsulated by a carbon matrix into spherical pebbles, which would inevitably contact the reactor's stainless steel container wall during salt circulation. Characterizing this interaction is crucial for reactor safety. Here, in this work, we report the tribocorrosion behavior of graphite sliding against Type 316H stainless steel lubricated by a FLiNaK (LiF:NaF:KF; 46.5:11.5:42 mol %) molten salt in an argon environment. Accelerated wear loss was observed at a higher temperature because of a lower molten salt viscosity and a higher corrosion rate. The graphite had a more rapid material loss at a higher sliding speed than stainless steel because of its higher vulnerability to vibration-induced microfracture. The salt-starved condition caused more material loss than either the no-salt or the salt-flooded condition because neither a graphite transfer film nor stable boundary lubrication could be established at salt starvation. An interesting dual-layer surface film was discovered on the stainless steel worn surface: a chromium-rich top film and a nickel-accumulated but chromium-depleted interlayer. The film composition and structure provide fundamental insights to the mechanochemical interactions between stainless steel and graphite in a molten salt environment.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Long-Term Static and Dynamic Corrosion Stability of Nonwetting Surfaces

Superhydrophobic surfaces (SHSs) and lubricant-infused surfaces (LISs) are two classes of nonwetting surfaces that have drawn attention due to their advanced functional properties including corrosion inhibition. Yet there is a conspicuous lack of corrosion study of SHSs and LISs with respect to their fabrication and material parameters, especially at high temperatures and under dynamic flow conditions over long durations, which is sought to be addressed in this article. Considering copper SHSs and LISs, a full factorial combinatorial study of two facile texturing processes, electrodeposition and etching, two different functionalization agents, stearic acid and mercaptan, and two types of infused lubricants, Krytox 104 and DOWSIL 510, is presented, encompassing over 650 measurements on 90 tested surfaces. All fabricated surfaces demonstrated water repellency with a contact angle above 150° and a sliding angle below 7°. For the first time, the study examines high-temperature corrosion stability and long-term corrosion durability of the nonwetting surfaces in both static fluid and dynamic turbulent flow conditions over a period of 30 days. Here, LISs and SHSs are shown to provide excellent corrosion inhibition over all tested corrosion conditions, with negligible presence of corrosion species on the surfaces and no deterioration of the texturing. The surfaces are also shown to rejuvenate easily to the initial wettability and corrosion resistance values. This study provides valuable insights into the selection of materials and processing parameters for the fabrication of nonwetting surfaces for the application of interest.

Copper↗
DOE OSTI2022

Interactions of Water with Pristine and Defective MoS 2

Molybdenum disulfide (MoS 2 ) is a lamellar solid lubricant often used in aerospace applications because of its extremely low friction coefficient (~0.01) in inert environments. The lubrication performance of MoS 2 is significantly impaired by exposure to even small amounts of water and oxygen, and the mechanisms behind this remain poorly understood. Here we use density functional theory calculations to study the binding of water on MoS 2 sheets with and without defects. In general, we find that pristine MoS 2 is slightly hydrophilic but that defects greatly increase the binding affinity for water. Intercalated water disrupts the crystal structure of bulk MoS 2 due to the limited space between lamellae (~3.4 Å), and this leads to generally unfavorable adsorption, except in the cases where water molecules are located on the sites of sulfur vacancies. We also find that water adsorption is more favorable directly below a surface layer of MoS 2 compared to in the bulk.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electrodeposited Mo x S y O z /Ni Tribological Coatings

Deposition of molybdenum disulfide (MoS 2 ) coatings using physical vapor deposition (PVD) and mechanical burnishing has been widely assessed for solid lubricants in space applications but still suffers from line-of-sight constraints on complex geometries. Here, we highlight one of the first demonstrations of electrodeposited Mo x S y O z and Mo x S y O z /Ni thin-film coatings from aqueous solutions of ammonium tetrathiomolybdate for solid lubricant applications and their remarkable ability to provide low coefficients of friction and high wear resistance. Characterization of the coating morphology shows amorphous microstructures with a high oxygen content and cracking upon drying. Even so, electrodeposited Mo x S y O z can achieve low steady-state coefficients of friction (μ ∼ 0.05–0.06) and wear rates (2.6 × 10 –7 mm 3 /(N m)) approaching those of physical vapor deposited coatings (2.3 × 10 –7 mm 3 /(N m)). Additionally, we show that adding dopants such as nickel increased the wear rate (7.5 × 10 –7 mm 3 /(N m)) and initial coefficient of friction (μ i = 0.23) due to compositional modifications such as dramatic sub-stoichiometry (S/Mo ∼ 1) and expression of a NiO x surface layer, although doping did reduce the degree of cracking upon drying.

Babuska, Tomas F.↗
DOE OSTI2020

Tribochemical Conversion of Methane to Graphene and Other Carbon Nanostructures: Implications for Friction and Wear

Tribochemistry involves chemical reactions occurring at sliding contact interfaces in the presence of gaseous and/or liquid media. It often leads to the formation of a solid reaction film (also termed boundary film) which controls friction and wear and hence the efficiency and reliability of moving mechanical systems (such as engines). Here we demonstrate tribochemical conversion of methane to graphene, nano-onion, and disordered carbons on the sliding surfaces of Ni-, Cu-, and CuNi-containing VN coatings at atmospheric pressure and room temperature, providing 2-3 orders of magnitude reduction in wear and similar to 50% reduction in friction compared to those of the uncoated steels. Transmission electron microscopy confirms that graphene forms preferably on metal rich nanoclusters of the composite coatings, while the carbon nano-onions are scattered throughout the carbon tribofilm. Ab initio molecular dynamics simulations elucidate underlying mechanisms involved in the tribochemical conversion of methane to carbon- based nanostructures in support of microscopic observations. These scientific findings may lead to new materials technologies that can use methane as a source for continuous and in situ lubrication. For example, there is an urgent need to curtail the uses of lubricating oils in natural gas compressors and engines as they contaminate the natural gas being compressed or burnt.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Techno-Economic and Life Cycle Assessment of Chemical Recycling and Upcycling of Mixed Plastics Waste Containing Poly-vinyl-chloride

Developing technologies that completely remove chlorine from plastic waste can allow its chemical recycling and upcycling with catalytic methods. Here, this study compares eight processes involving different dechlorination methods (absorption columns, adsorption in beds of zeolites, catalytic dechlorination, and dissolution in ionic liquids) and chemical conversion technologies (incineration, pyrolysis, hydrogenolysis) to upgrade mixed plastics waste to various products (e.g., electricity, fuels, virgin polymers, and lubricant oil). The analysis determines that the absorption of chlorine in columns with basic aqueous solutions is limited to plastics waste with PVC concentrations below 0.1%. Dissolution in ionic liquids is not cost-competitive. On the contrary, two-step processes with catalytic dechlorination followed by thermochemical catalytic depolymerization, either pyrolysis or hydrogenolysis, significantly improve process economics and emissions. The most economically viable alternative is hydrogenolysis for producing lubricants, while the technology with the lowest global warming potential is chemical recycling via catalytic pyrolysis.

circular economy↗
DOE OSTI2023

A two-stage strategy for upcycling chlorine-contaminated plastic waste

Abstract Chemical upcycling of polyolefin plastic waste to lubricant, wax and fuel-range hydrocarbons over metal-based catalysts is a crucial technological solution to the enormous environmental threat posed by plastic waste. However, currently available methods are incompatible with chlorine-contaminated feedstocks. Here we report a two-stage strategy for upcycling chlorine-contaminated polypropylene. First, magnesia–alumina mixed oxide at 30 bar H 2 and 250 °C serves as a chlorine trap by rapidly forming solid chloride, resulting in nearly complete chlorine extraction from the polyolefin melt. This enables the upcycling of plastic waste with up to 10% polyvinyl chloride content to lubricants over ruthenium-based catalysts, in the second stage. The strategy is also applicable to chlorinated aromatics and alkanes. The proposed strategy renders hydrocracking and hydrogenolysis catalysts less sensitive to the chlorine impurities in feedstocks while eliminating HCl emissions and chlorine contamination in products. It could incentivize further progress in plastics upcycling.

Environmental Sciences & Ecology↗
DOE OSTI2020

Structure and dynamics of hydrodynamically interacting finite-size Brownian particles in a spherical cavity: Spheres and cylinders

The structure and dynamics of confined suspensions of particles of arbitrary shape are of interest in multiple disciplines from biology to engineering. Theoretical studies are often limited by the complexity of long-range particle-particle and particle-wall forces, including many-body fluctuating hydrodynamic interactions. Here, we report a computational study on the diffusion of spherical and cylindrical particles confined in a spherical cavity. We rely on an immersed-boundary general geometry Ewald-like method to capture lubrication and long-range hydrodynamics and include appropriate non-slip conditions at the confining walls. A Chebyshev polynomial approximation is used to satisfy the fluctuation-dissipation theorem for the Brownian suspension. We explore how lubrication, long-range hydrodynamics, particle volume fraction, and shape affect the equilibrium structure and the diffusion of the particles. It is found that once the particle volume fraction is greater than 10%, the particles start to form layered aggregates that greatly influence particle dynamics. Hydrodynamic interactions strongly influence the particle diffusion by inducing spatially dependent short-time diffusion coefficients, stronger wall effects on the particle diffusion toward the walls, and a sub-diffusive regime-caused by crowding-in the long-time particle mobility. The level of asymmetry of the cylindrical particles considered here is enough to induce an orientational order in the layered structure, decreasing the diffusion rate and facilitating a transition to the crowded mobility regime at low particle concentrations. Our results offer fundamental insights into the diffusion and distribution of globular and fibrillar proteins inside cells.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigations in the tape-to-tape contact resistance and contact composition in superconducting CORC ® wires

Conductor on Round Core (CORC®) wires and cables, constructed from multiple layers of helically wound REBa 2 Cu 3 O 7–δ tapes, are a promising cable technology for high field magnet applications. An important feature of high-temperature superconductor cables is the ability to share current between conductors, allowing current to bypass drops in I c and minimizing the risk of hot spot formation, which could lead to potential burnout in the superconductor. In contrast to stacked-tape cables, which have continuous contact between tapes, in CORC® the transfer points occur at discrete tape crossovers. The tape-to-tape contact resistance, R c , plays a critical role in the current sharing capabilities and current distribution in cables. For the work reported here, special CORC® wires were manufactured using different winding parameters to investigate variations in R c . Variations comprised inclusion of a lubricant, different lubricant conductivity, inclusion of pre-tinning, and heating briefly to melt the solder. Cables were first tested as straight lengths, followed by bending to a 10 cm diameter. In straight cables R c values ranged from 1 to over 1000 μΩ cm 2 , depending on cabling parameters, with the highest values being found for cables made by the present 'standard' process. Bending the cables to a 10 cm diameter decreased R c by a factor 2–5. Tinning with PbSn decreased R c by three orders of magnitude compared to standard CORC® wires, and heat treating wires with tinned conductor resulted in only a small further decrease in R c . Based on the measured R c at an electric field of 1 μV cm –1 the resulting current transfer length between layers can range from a few millimeters to a tens of centimeters. Examination of contacts with a laser confocal microscope showed plastic deformation of the copper at the edges of the contact overlap area, apparently caused by thicker plating at tape edges digging into the copper of neighboring layers. These images reveal that only a fraction of the total contact surface may actually be touching when there is nothing to compensate for height differential. Images of the PbSn coated tapes indicated that application of solder produces a much more uniform contact surface and higher contact area. Furthermore, imaging of CORC® cross-sections confirmed that in the non-tinned cables there are many regions where tapes are not in contact, while in contrast the PbSn cable shows significantly more contact between the tapes. These different imaging techniques reveal that tape surface morphology is a significant parameter in determining R c .

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

The surface stress of biomedical silicones is a stimulant of cellular response

Silicones are commonly used for lubrication of syringes, encapsulation of medical devices, and fabrication of surgical implants. While silicones are generally viewed as relatively inert to the cellular milieu, they can mediate a variety of inflammatory responses and other deleterious effects, but the mechanisms underlying the bioactivity of silicones remain unresolved. Here, we report that silicone liquids and gels have high surface stresses that can strongly resist deformation at cellular length scales. Biomedical silicones, including syringe lubricants and fillings from FDA-approved breast implants, readily adsorb matrix proteins and activate canonical rigidity sensing pathways through their surface stresses. In 3D culture models, liquid silicone droplets support robust cellular adhesion and the formation of multinucleated monocyte-derived cell masses that recapitulate phenotypic aspects of granuloma formation in the foreign body response. Together, our findings implicate surface stress as a cellular stimulant that should be considered in application of silicones for biomedical purposes.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

Report of the Condition of a General Electric Transportation Systems Gearbox

Wind power plant operations and maintenance (O&M) costs remain an appreciable contributor to the overall cost of wind energy. Premature of wind turbine gearboxes failures are often a result of abrasive wear, micropitting, scuffing, white-etch cracks, and macropitting issues. Micropitting is a fatigue phenomenon that occurs in Hertzian contacts in both gears and rolling-element bearings that operate in mixed or micro elastohydrodynamic lubrication regimes. Micropitting is influenced by and manifests itself in many different ways depending on operating conditions such as load, speed and operating temperature, and on factors such as gear geometry and accuracy, tooth flank roughness, percentage of tooth sliding, and lubricant composition. Despite much research by many investigators, micropitting remains complex, unpredictable, and difficult to control and remains a problem in wind turbine gearboxes. The purpose of this report is to document and describe the micropitting damage observed in a wind turbine gearbox, thereby facilitating further analysis and examination in future reports.

17 WIND ENERGY↗
DOE OSTI2021

Evaluation of the Volatile Species Associated with the K-Area Complex Blend Cans (D5043)

In the K-Area Complex (KAC), blend cans are used to down blend plutonium oxide for future disposal at the Waste Isolation Pilot Plant (WIPP). The blend can is a thin walled screw lid container that is used to down blend a measured amount of plutonium oxide with adulterant to reduce the attractiveness of the plutonium. The oxide and adulterant are mixed within the blend can and the blend can is packaged into a thick walled outer container. The blend cans are procured from an offsite vendor that uses a lubricant in the can manufacturing process. A thin coating of the lubricant adheres to the outer surface of the blend can and both inner and outer surfaces of the blend can cap.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Scale up, Field testing, and Optimization of Nontoxic, Durable, Economical Coatings for Control of Biofouling and Corrosion (Abstract Only)

The objective of this project is the technical maturation and demonstration of a durable, economical, and nontoxic coating, Superhydrophobic Lubricant Infused Composite (SLIC), that will prevent fouling organisms from growing on marine and hydrokinetic (MHK) structures and prevent invasive mussels from growing on hydropower structures. SLIC technology was developed and patented by PNNL. It combines multiple antifouling mechanisms to provide excellent antifouling performance, durability, and low hydrodynamic drag without using toxic materials. Advanced proof-of-concept testing and demonstrations completed during a Phase 1 TCF project attracted industry interest and partnerships for this Phase 2 effort focused on maturation of a commercial product. Specific tasks and tests will shift the development emphasis to optimizing formulations, validating antifouling performance to address specific application needs, explore compatibility with other paint systems, develop a product with useful shelf life (in can), and determine curing times and effective applications methodology. Phase 2 efforts will focus upon technology transfer and commercialization of the technology with the industrial team. Industrial partners now include a coatings development specialist (Lorama), hydrophobic material manufacturer and paint developer (Dry Surface Technologies), nontoxic biodegradable lubricants manufacturer (BioBlend), and aquatic applications specialists (Prometheus Innovations, River Connectivity Systems). Engagement with the MHK device developers, the PNNL Marine and Coastal Research Laboratory (MCRL) test site in Sequim WA, Bureau of Reclamation, and Taylor Shellfish throughout the project will provide topical expertise and field test sites that will deliver crucial real-world performance data. Through this Phase 2 effort, SLIC will transition from a Technical Readiness Level (TRL) 5 to TRL 6 and long-term performance data will be acquired through demonstrations. The field test data will allow optimization of SLIC formulation to enhance performance (e.g., durability) and packaging, which are key de-risking activities for technology transfer and ultimately to the production of a viable commercial product.

13 HYDRO ENERGY↗
DOE OSTI2025

Investigations on the Thermal Stability and Kinetics of Biolubricants Synthesized from Different Types of Vegetable Oils

Petroleum-based lubricants raise environmental concerns due to their non-biodegradability and toxicity, whereas biobased lubricants underperform owing to low thermal stability. This study examined and compared three vegetable oils, along with their chemically modified versions, to better understand their suitability as biolubricants. High oleic soybean oil (HOSOY), regular soybean oil (RSOY), and waste cooking oil (WCO) were subjected to chemical modification, where isopropyl groups were attached to the fatty acid chains of the oils to produce branched oils, i.e., b-HOSOY, b-RSOY, and b-WCO. The detailed kinetic study of each regular and modified sample was investigated using thermogravimetric analysis. The kinetic parameters, such as the activation energies, reaction rate, and pre-exponential factor, were generated via Friedman methods. The differential thermal gravimetric (DTG) analysis showed low volatilization at the onset temperature in each modified oil as compared with the unmodified samples under an oxidative environment. Furthermore, the comparative kinetic studies demonstrated the enhanced thermoxidative stability of the modified products relative to their unaltered counterparts. Among the tested oils, the b-RSOY showed an average activation energy of 325 kJ/mol, followed by the b-WCO: 300 kJ/mol and the b-HOSOY: 251 kJ/mol, indicating the most stable modified product under an oxidative environment. For all the samples, the pre-exponential factors were in good agreement with the activation energies, which validates that finding the pre-exponential components is crucial to the kinetic analysis.

Sarker, Majher I. (ORCID:0000000299509274)↗
NASA NTRS1969

Electromechanical rotary actuator operates over wide temperature range

Electromechanical rotary actuator, which operates over wide temperature range, contains a spring stop which has been calculated to limit internal deceleration loads to a magnitude equal to stall torque. Cryogenic capability is obtained by using dry lubricant on the gears and no lubrication on the bearings.

Sullivan, S. F.↗
NASA NTRS1970

Technique for improving hydrodynamic gyro bearings

Conical or spherical, spirally grooved grease bearings have an inclined surface which is machined inboard of the grooved surface. The indentation and inclined surface provide a reservoir for forced out lubricant, and when rotation begins, centrifugal force returns the lubricant to the grooved area.

Broussard, P., Jr.↗
NASA NTRS1970

Accelerated vacuum testing of long life ball bearings and sliprings

Extensive analytical studies and testing have been conducted on bearings and sliprings in vacuum at temperatures from 30 to 130 F. Thirty-six bearings lubricated with two types of oil were tested in vacuum of less than 10 to the minus 8th power torr at speeds from 55 to 180 rpm. Temperatures, load, speed, and oil viscosity were varied to evaluate the effects on life and wear. All bearings performed successfully during a 7-month test, and the potential merits of the two oils were compared. Over 25 different, dry-lubricated brush/slipring material combinations have been tested, with variations of brush and ring design and surface speed. Test results indicate the probability of 10 years or more of slipring and brush lifetime with properly designed brushes for 1-in.-diameter ring rotating at 60 rpm.

C. R. Meeks↗
NASA NTRS1971

Integral lift engine preliminary design

A preliminary mechanical design of a complete lift fan engine system is reported. A description of the lift fan engine, layout drawings of the components and complete engine, and a discussion of the design analyses and results are presented. The design features and areas of analysis include fan and compressor rotor blades of composite construction, a combustor folded over the compressor, relatively high-temperature blades in the high-pressure turbine, the first stage of the low-pressure turbine used for bearing support and ducting of lubricant to the bearings, a complete lubrication system, critical speeds of the shafting, and vibration and flutter of the blading.

Pratt, W.↗