Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Analysis of alkaline exchange membrane fuel cells performance at different operating conditions using DC and AC methods

We report membrane electrode assemblies (MEAs) for anion exchange membrane fuel cells (AEMFCs) were manufactured from commercial materials: Pt/C catalyst, A201 AEM and AS4 ionomer by using an industrial mass-production digital printing method. The MEA designs selected are close to those recommended by US Department of Energy, including low loading of platinum on the cathode side (0.2 mg cm -2 ). Polarization curves and electrochemical impedance spectroscopy (EIS) were applied for MEA evaluation in fuel cell conditions with variation of gas humidification and oxygen partial pressure (air vs oxygen). The typical impedance curves recorded at H 2 /O 2 gas configuration consist of high- and medium-frequency arcs responsible for hydrogen oxidation and oxygen reduction, respectively. Operation with air as a cathode feed gas resulted in a decrease in AEMFC performance due to possible CO 2 poisoning and mass transfer losses. At the same time, EIS demonstrated formation of a low frequency loop due to diffusion limitations. Despite the low loading of platinum on the cathode (0.2 mg cm -2 ), a peak power density of ~330 mW cm -2 was achieved (at 50/50% of RH on anode and cathode), which is substantially higher performance than for AEMFC MEAs tested at similar conditions.

25 ENERGY STORAGE↗

Ammonia-fed reversible protonic ceramic fuel cells with Ru-based catalyst

Abstract The intermediate operating temperatures (~400–600 °C) of reversible protonic ceramic fuel cells (RePCFC) permit the potential use of ammonia as a carbon-neutral high energy density fuel and energy storage medium. Here we show fabrication of anode-supported RePCFC with an ultra-dense (~100%) and thin (4 μm) protonic ceramic electrolyte layer. When coupled to a novel Ru-(BaO) 2 (CaO)(Al 2 O 3 ) (Ru-B2CA) reversible ammonia catalyst, maximum fuel-cell power generation reaches 877 mW cm −2 at 650 °C under ammonia fuel. We report relatively stable operation at 600 °C for up to 1250 h under ammonia fuel. In fuel production mode, ammonia rates exceed 1.2 × 10 −8 NH 3 mol cm −2 s −1 at ambient pressure with H 2 from electrolysis only, and 2.1 × 10 −6 mol NH 3 cm −2 s −1 at 12.5 bar with H 2 from both electrolysis and simulated recycling gas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrocarbon Ionomeric Binders for Fuel Cells and Electrolyzers

Abstract Ionomeric binders in catalyst layers, abbreviated as ionomers, play an essential role in the performance of polymer–electrolyte membrane fuel cells and electrolyzers. Due to environmental issues associated with perfluoroalkyl substances, alternative hydrocarbon ionomers have drawn substantial attention over the past few years. This review surveys literature to discuss ionomer requirements for the electrodes of fuel cells and electrolyzers, highlighting design principles of hydrocarbon ionomers to guide the development of advanced hydrocarbon ionomers.

25 ENERGY STORAGE↗

The Electrochemical Properties of Sr(Ti,Fe)O 3-δ for Anodes in Solid Oxide Fuel Cells

Reduction-stable mixed ionic and electronic conductors such as Sr(Ti,Fe)O 3-δ (STF) are promising materials for application in anodes of solid oxide fuel cells. The defect chemistry of STF and its properties as solid oxide fuel cell (SOFC) cathode have been studied thoroughly, while mechanistic investigations of its electrochemical properties as SOFC anode material are still scarce. In this study, thin film model electrodes of STF with 30% and 70% Fe content were investigated in H 2 +H 2 O atmosphere by electrochemical impedance spectroscopy. Lithographically patterned thin film Pt current collectors were applied on top or beneath the STF thin films to compensate for the low electronic conductivity under reducing conditions. Oxygen exchange resistances, electronic and ionic conductivities and chemical capacitances were quantified and discussed in a defect chemical model. Increasing Fe content increases the electro-catalytic activity of the STF surface as well as the electronic and ionic conductivity. Current collectors on top also increase the electrochemical activity due to a highly active Pt-atmosphere-STF triple phase boundary. Furthermore, the electrochemical activity depends decisively on the H 2 :H 2 O mixing ratio and the polarization. Lastly, Fe 0 nanoparticles may evolve on the surface in hydrogen rich atmospheres and increase the hydrogen adsorption rate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fuel Cell Combined Heat and Power Commercial Demonstration

This is the annual report for the Market Transformation project as required by DOE EERE's Fuel Cell Technologies Office. We have been provided with a specific format. It describes the work that was done in developing evaluating the performance of 5 kW stationary combined heat and power fuel cell systems that have been deployed in Oregon and California. It also describes the business case that was developed to identify markets and address cost.

combined heat and power↗

BC Transit Fuel Cell Bus Project: Evaluation Results Report

This report evaluates a fuel cell electric bus demonstration led by British Columbia Transit (BC Transit) in Whistler, Canada. BC Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's National Renewable Energy Laboratory to evaluate the buses in revenue service. This evaluation report covers two years of revenue service data on the buses from April 2011 through March 2013.

30 DIRECT ENERGY CONVERSION↗

Impacts of electrode coating irregularities on polymer electrolyte membrane fuel cell lifetime using quasi in-situ infrared thermography and accelerated stress testing

In-line quality control diagnostics for roll-to-roll (R2R) manufacturing techniques will play a key role in the future commercialization of the polymer electrolyte membrane fuel cell (PEMFC) used in automotive applications. These diagnostics monitor the fabrication of the membrane electrode assembly (MEA), which detect and flag any non-uniformity that may potentially harm PEMFC performance and/or lifetime. This will require quantitative thresholds and a clear distinction between harmful defects and harmless coating irregularities. Thus, novel fuel cell hardware with quasi in-situ infrared (IR) thermography capabilities is utilized to understand how bare spots in the cathode electrode impact MEA lifetime. An accelerated stress test (AST) simulates chemical and mechanical degradation modes seen in vehicular operation. The actual open circuit voltage and rate of change of this voltage are used as in-situ indicators for MEA failure, enabling capture of the progression of failure point development. Bare spot coating irregularities located at the center of the electrode were found to have no impact on MEA lifetime when compared to a pristine MEA. However, MEA lifetime was found to be considerably shortened when these same irregularities are located at the cathode inlet and, especially, the anode inlet regions of the fuel cell.

36 MATERIALS SCIENCE↗

Stationary Direct Methanol Fuel Cells Using Pure Methanol

This project developed stationary direct methanol fuel cells (DMFCs) using pure methanol as the fuel, integrating complementary institutional expertise on platinum group metals free (PGM-free) cathode catalyst (UB), supported anode catalysts (KSU), electrode fabrication, characterization, and optimization (CMU), and multi-phase mass transfer (KU). The proposed cost-effective prototype will deliver reliable and durable performance using a methanol-tolerant PGM-free cathode and a high-performance anode with low PtRu loading. At the end of the project, the research team is expected to deliver a single cell (50 cm 2 ) with ≤3 mg PGM /cm 2 that achieves 300 mW/cm 2 using pure methanol.

30 DIRECT ENERGY CONVERSION↗

Durable High Power Density Fuel Cell Cathodes for Heavy-Duty Vehicles

The aim of this project was to advance the performance and durability of proton exchange membrane fuel cells (PEMFCs) for their use in the electrification of heavy-duty vehicles (HDVs). With an emphasis on total cost of ownership for HDVs, the development of the fuel cells focuses more heavily on the efficiency and lifetime (i.e., durability) than past focus on platinum group metal (PGM) costs and power density. This project takes a unique approach to achieving these goals – using next-generation polymer electrolytes in the electrodes that yield significant improvements in performance and dramatic reductions in degradation rates. A key outcome of the project was an ionomer/catalyst combination of a Pt catalyst on a low surface area carbon support (Pt/LSC) with a high oxygen permeability ionomer (HOPI) that met both the project’s performance target (current at 0.8 V, >0.3 A/cm 2 ) and durability target (voltage loss at 0.8 A/cm 2 , <30 mV) with the goal of projected a >4X increase in life-time.

08 HYDROGEN↗

The solid polymer electrolyte fuel cell for the Space Shuttle Orbiter.

Recent developments in the General Electric solid polymer electrolyte fuel cell have demonstrated the capability of 2000 hours of maintenance-free life and the potential for 5000 to 10,000 hours of useful life with invariant performance. Hardware developments for a 5 kW fuel cell module directed toward NASA's Space Shuttle Orbiter application have demonstrated the capability of operation on propulsion-grade reactants, operation with simple stop/start procedures, and with a specific weight of 25 lb/kW for a complete module.

Chapman, L. E.↗

Evaluation of a single cell and candidate materials with high water content hydrogen in a generic solid oxide fuel cell stack test fixture, Part II: materials and interface characterization

A generic solid oxide fuel cell (SOFC) test fixture was developed to evaluate candidate materials under realistic conditions. A commerical 50 mm x 50 mm NiO-YSZ anode supported thin YSZ electrolyte cell with lanthanum strontium manganite (LSM) cathode was tested to evaluate the stability of candidate materials. The cell was tested in two stages at 800oC: stage I of low (~3% H2O) humidity and stage II of high (~30% H2O) humidity hydrogen fuel at constant voltage or constant current mode. Part I of the work was published earlier with information of the generic test fixture design, materials, cell performance, and optical post-mortem analysis. In part II, detailed microstructure and interfacial characterizations are reported regarding the SOFC candidate materials: (Mn,Co)-spinel conductive coating, alumina coating for sealing area, ferritic stainless steel interconnect, refractory sealing glass, and their interactions with each other. Overall, the (Mn,Co)-spinel coating was very effective in minimizing Cr migration. No Cr was identified in the cathode after 1720h at 800oC. Aluminization of metallic interconnect also proved to be chemically compatible with alkaline-earth silicate sealing glass. The details of interfacial reaction and microstructure development are discussed.

(Mn,Co)-spinel↗

Orange County Transportation Authority Fuel Cell Electric Bus Progress Report - Data Period Focus: Feb. 2020 through Jul. 2021 [Slides]

This report presents early results from a deployment of fuel cell electric buses (FCEBs) operated by Orange County Transportation Authority (OCTA) in Southern California. The ten FCEBs, produced by New Flyer, feature an electric drive propulsion system powered by a Ballard fuel cell system. The project team is collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory (NREL) to evaluate the buses in revenue service. The goal of this evaluation is to compare the FCEB performance to that of conventional technology and to track progress over time toward meeting the technical targets set by DOE and the Department of Transportation (DOT). The FCEBs were delivered beginning in late-2019, and were placed in service on February 9, 2020. The data period covers February 2020 through July 2021. NREL collects data on ten 2016 model year compressed natural gas (CNG) buses as a baseline comparison at OCTA.

30 DIRECT ENERGY CONVERSION↗

Water outlet control mechanism for fuel cell system operation in variable gravity environments

A self-regulated water separator provides centrifugal separation of fuel cell product water from oxidant gas. The system uses the flow energy of the fuel cell's two-phase water and oxidant flow stream and a regulated ejector or other reactant circulation pump providing the two-phase fluid flow. The system further uses a means of controlling the water outlet flow rate away from the water separator that uses both the ejector's or reactant pump's supply pressure and a compressibility sensor to provide overall control of separated water flow either back to the separator or away from the separator.

Vasquez, Arturo↗

Deviations from Vegard's law and evolution of the electrocatalytic activity and stability of Pt-based nanoalloys inside fuel cells by in operando X-ray spectroscopy and total scattering

Catalysts for energy related applications, in particular metallic nanoalloys, readily undergo atomic-level changes during electrochemical reactions. The origin, dynamics and implications of the changes for the catalysts’ activity inside fuel cells though are not well understood. This is largely because they are studied on model nanoalloy structures under controlled laboratory conditions. Here we use combined synchrotron X-ray spectroscopy and total scattering to study the dynamic behaviour of nanoalloys of Pt with 3d-transition metals as they function at the cathode of an operating proton exchange membrane fuel cell. Results show that the composition and atomic structure of the nanoalloys change profoundly, from the initial state to the active form and further along the cell operation. The electrocatalytic activity of the nanoalloys also changes. The rate and magnitude of the changes may be rationalized when the limits of traditional relationships used to connect the composition and structure of nanoalloys with their electrocatalytic activity and stability, such as Vegard's law, are recognized. In particular, deviations from the law inherent for Pt-3d metal nanoalloys can well explain their behaviour under operating conditions. Moreover, it appears that factors behind the remarkable electrocatalytic activity of Pt-3d metal nanoalloys, such as the large surface to unit volume ratio and “size misfit” of the constituent Pt and 3d-transition metal atoms, also contribute to their instability inside fuel cells. The new insight into the atomic-level evolution of nanoalloy electrocatalysts during their lifetime is likely to inspire new efforts to stabilize transient structure states beneficial to their activity and stability under operating conditions, if not synthesize them directly.

25 ENERGY STORAGE↗

SunLine Transit Agency Fuel Cell Electric Bus Progress Report - Data Period Focus: Jan. 2020 through Dec. 2021 [Slides]

This report presents early results from a deployment of fuel cell electric buses (FCEBs) operated by SunLine Transit Agency in the Coachella Valley area of California. The five FCEBs, produced by New Flyer, feature an electric drive propulsion system powered by a Ballard fuel cell system. The project team is collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory (NREL) to evaluate the buses in revenue service. The goal of this evaluation is to compare the FCEB performance to that of conventional technology and to track progress over time toward meeting the technical targets set by DOE and the Department of Transportation (DOT). The FCEBs were delivered beginning in mid-2019. The data period covers January 2020 through December 2021. NREL collects data on five 2019 model year compressed natural gas (CNG) buses as a baseline comparison at SunLine. These new CNG buses were phased into service beginning in April 2020.

08 HYDROGEN↗

A Direct Manufacturing Cost Model for Solid‐Oxide Fuel Cell Stacks

Abstract This work details efforts to estimate the direct manufacturing cost of solid oxide fuel cell (SOFC) stack components for combined heat and power applications. The main research goals are to identify the major contributors to fuel cell stack manufacturing costs, examine the influence of both production volume and stack size on cost, and compare the results of the cost trajectories with the U.S. Department of Energy SOFC stack manufacturing cost target of $238 kWe −1 (in 2015) and industry reported cost projections and to identify critical areas for manufacturing research and development. Stack component direct manufacturing costs are modeled for net electricity capacity of 1, 10, 50, 100 and 250 kWe across annual production volumes of 10, 1,000, 10,000 and 50,000 systems per year. Overall stack manufacturing costs range from $5,387 kWe −1 to a minimum of about $166 kWe −1 for a 250 kWe system at 50,000 systems per year. To meet the manufacturing cost target of $238 kWe −1 , a minimum annual production of 100–250 MWe per year would be required. Reduction opportunities for stack cost are expected to be available, mainly with the adoption of thinner cells and stack components, higher levels of factory automation, and more sensitive in‐line defect diagnostics.

Scataglini, R.↗