Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Finite Element Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Thermal Analysis on Cryogenic Liquid Hydrogen Tank on an Unmanned Aerial Vehicle System

Thermal analyses are performed on the liquid hydrogen (LH2) tank designed for an unmanned aerial vehicle (UAV) powered by solar arrays and a regenerative proton-exchange membrane (PEM) fuel cell. A 14-day cruise mission at a 65,000 ft altitude is considered. Thermal analysis provides the thermal loads on the tank system and the boiling-off rates of LH2. Different approaches are being considered to minimize the boiling-off rates of the LH2. It includes an evacuated multilayer insulation (MLI) versus aerogel insulation on the LH2 tank and aluminum versus stainless steel spacer rings between the inner and outer tank. The resulting boil-off rates of LH2 provided by the one-dimensional model and three-dimensional finite element analysis (FEA) on the tank system are presented and compared to validate the results of the three-dimensional FEA. It concludes that heat flux through penetrations by conduction is as significant as that through insulation around the tank. The tank system with MLI insulation and stainless steel spacer rings result in the lowest boiling-off rate of LH2.

Wang, Xiao-Yen↗

Tapping mode microwave impedance microscopy

We report tapping mode microwave impedance imaging based on atomic force microscope platforms. The shielded cantilever probe is critical to localize the tip-sample interaction near the tip apex. The modulated tip-sample impedance can be accurately simulated by the finite-element analysis and the result agrees quantitatively to the experimental data on a series of thin-film dielectric samples. The tapping mode microwave imaging is also superior to the contact mode in that the thermal drift in a long time scale is totally eliminated and an absolute measurement on the dielectric properties is possible. We demonstrated tapping images on working nanodevices, and the data are consistent with the transport results.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Reliability-based failure analysis of brittle materials

The reliability of brittle materials under a generalized state of stress is analyzed using the Batdorf model. The model is modified to include the reduction in shear due to the effect of the compressive stress on the microscopic crack faces. The combined effect of both surface and volume flaws is included. Due to the nature of fracture of brittle materials under compressive loading, the component is modeled as a series system in order to establish bounds on the probability of failure. A computer program was written to determine the probability of failure employing data from a finite element analysis. The analysis showed that for tensile loading a single crack will be the cause of total failure but under compressive loading a series of microscopic cracks must join together to form a dominant crack.

Powers, Lynn M.↗

Recent developments in equivalent plate modeling for wing shape optimization

A new technique for structural modeling of airplane wings is presented taking transverse shear effects into account. The kinematic assumptions of first order shear deformation plate theory in combination with numerical analysis based on simple polynomials which define geometry, construction and displacement approximations lead to analytical expressions for elements of the stiffness and mass matrices and load vector. Contributions from the cover skins, spar and rib caps and spar and rib webs are included as well as concentrated springs and concentrated masses. Limitations of current equivalent plate wing modeling techniques based on classical plate theory are discussed, and the improved accuracy of the new equivalent plate technique is demonstrated through comparison to finite element analysis and test results. Analytical derivatives of stiffness, mass and load terms with respect to wing shape lead to analytic sensitivities of displacements, stresses and natural modes with respect to planform shape and depth distribution. This makes the new capability an effective structural tool for wing shape optimization.

Livne, Eli↗

Design/Analysis of the JWST ISIM Bonded Joints for Survivability at Cryogenic Temperatures

A major design and analysis challenge for the JWST ISIM structure is thermal survivability of metal/composite bonded joints below the cryogenic temperature of 30K (-405 F). Current bonded joint concepts include internal invar plug fittings, external saddle titanium/invar fittings and composite gusset/clip joints all bonded to M55J/954-6 and T300/954-6 hybrid composite tubes (75mm square). Analytical experience and design work done on metal/composite bonded joints at temperatures below that of liquid nitrogen are limited and important analysis tools, material properties, and failure criteria for composites at cryogenic temperatures are sparse in the literature. Increasing this challenge is the difficulty in testing for these required tools and properties at cryogenic temperatures. To gain confidence in analyzing and designing the ISIM joints, a comprehensive joint development test program has been planned and is currently running. The test program is designed to produce required analytical tools and develop a composite failure criterion for bonded joint strengths at cryogenic temperatures. Finite element analysis is used to design simple test coupons that simulate anticipated stress states in the flight joints; subsequently the test results are used to correlate the analysis technique for the final design of the bonded joints. In this work, we present an overview of the analysis and test methodology, current results, and working joint designs based on developed techniques and properties.

Bartoszyk, Andrew↗

Shear buckling analysis of a hat-stiffened panel

A buckling analysis was performed on a hat-stiffened panel subjected to shear loading. Both local buckling and global buckling were analyzed. The global shear buckling load was found to be several times higher than the local shear buckling load. The classical shear buckling theory for a flat plate was found to be useful in predicting the local shear buckling load of the hat-stiffened panel, and the predicted local shear buckling loads thus obtained compare favorably with the results of finite element analysis.

Ko, William L.↗

Verification and Large Deformation Analysis Using the Reproducing Kernel Particle Method

The reproducing kernel particle method (RKPM) is a meshless method used to solve general boundary value problems using the principle of virtual work. RKPM corrects the kernel approximation by introducing reproducing conditions which force the method to be complete to arbritrary order polynomials selected by the user. Effort in recent years has led to the implementation of RKPM within the Sierra/SM physics software framework. The purpose of this report is to investigate convergence of RKPM for verification and validation purposes as well as to demonstrate the large deformation capability of RKPM in problems where the finite element method is known to experience difficulty. Results from analyses using RKPM are compared against finite element analysis. A host of issues associated with RKPM are identified and a number of potential improvements are discussed for future work.

97 MATHEMATICS AND COMPUTING↗

LINAC Electrical Cabinets - Structural Analysis

Along LINAC s downstream path is a floor containing various cabinets above the LINAC. Of the dozens of cabinets are 4 specific cabinet types: PNF Modulator, PNF Power Supply, Water Skid, and Marx. Each of these cabinets may contain some of the various contents that include electronics, wiring, pipelines, circuits, and conduits. Lab Technicians perform maintenance and inspections of the cabinets and need to access every part, including the top section that is subject to the weight of the technician standing on top. To ensure the cabinet is structurally safe, a CAD model will be developed for each cabinet and a Finite Element Analysis (FEA) will be performed on each cabinet to confirm it is safe to stand on.

Blas, Efren↗

Probabilistic Prediction of Lifetimes of Ceramic Parts

ANSYS/CARES/PDS is a software system that combines the ANSYS Probabilistic Design System (PDS) software with a modified version of the Ceramics Analysis and Reliability Evaluation of Structures Life (CARES/Life) Version 6.0 software. [A prior version of CARES/Life was reported in Program for Evaluation of Reliability of Ceramic Parts (LEW-16018), NASA Tech Briefs, Vol. 20, No. 3 (March 1996), page 28.] CARES/Life models effects of stochastic strength, slow crack growth, and stress distribution on the overall reliability of a ceramic component. The essence of the enhancement in CARES/Life 6.0 is the capability to predict the probability of failure using results from transient finite-element analysis. ANSYS PDS models the effects of uncertainty in material properties, dimensions, and loading on the stress distribution and deformation. ANSYS/CARES/PDS accounts for the effects of probabilistic strength, probabilistic loads, probabilistic material properties, and probabilistic tolerances on the lifetime and reliability of the component. Even failure probability becomes a stochastic quantity that can be tracked as a response variable. ANSYS/CARES/PDS enables tracking of all stochastic quantities in the design space, thereby enabling more precise probabilistic prediction of lifetimes of ceramic components.

Nemeth, Noel N.↗

Dispersion retrieval from multi-level ultra-deep reactive-ion-etched microstructures for terahertz slow-wave circuits

A multi-level microstructure is proposed for terahertz slow-wave circuits, with dispersion relation retrieved by scattering parameter measurements. The measured return loss shows strong resonances above the cutoff with negligible phase shifts compared with finite element analysis. Splitting the circuit into multi levels enables a low aspect ratio configuration that alleviates the loading effect of deep-reactive-ion etching on silicon wafers. This makes it easier to achieve flat-etched bottom and smooth sidewall profiles. The dispersion retrieved from the measurement, therefore, corresponds well to the theoretical estimation. The result provides a straightforward way to the precise determination of dispersions in terahertz vacuum electronics.

36 MATERIALS SCIENCE↗

Ply-level failure analysis of a graphite/epoxy laminate under bearing-bypass loading

A combined experimental and analytical study was conducted to investigate and predict the failure modes of a graphite/epoxy laminate subjected to combined bearing and bypass loading. Tests were conducted in a test machine that allowed the bearing-bypass load ratio to be controlled while a single-fastener coupon was loaded to failure in either tension or compression. Onset and ultimate failure modes and strengths were determined for each test case. The damage-onset modes were studied in detail by sectioning and micrographing the damaged specimens. A two-dimensional, finite-element analysis was conducted to determine lamina strains around the bolt hole. Damage onset consisted of matrix cracks, delamination, and fiber failures. Stiffness loss appeared to be caused by fiber failures rather than by matrix cracking and delamination. An unusual offset-compression mode was observed for compressive bearing-bypass laoding in which the specimen failed across its width along a line offset from the hole. The computed lamina strains in the fiber direction were used in a combined analytical and experimental approach to predict bearing-bypass diagrams for damage onset from a few simple tests.

Naik, R. A.↗

Ply-level failure analysis of a graphite/epoxy laminate under bearing-bypass loading

A combined experimental and analytical study was conducted to investigate and predict the failure modes of a graphite/epoxy laminate subjected to combined bearing and bypass loading. Tests were conducted in a test machine that allowed the bearing-bypass load ratio to be controlled while a single-fastener coupon was loaded to failure in either tension or compression. Onset and ultimate failure modes and strengths were determined for each test case. The damage-onset modes were studied in detail by sectioning and micrographing the damaged specimens. A two-dimensional, finite-element analysis was conducted to determine lamina strains around the bolt hole. Damage onset consisted of matrix cracks, delamination, and fiber failures. Stiffness loss appeared to be caused by fiber failures rather than by matrix cracking and delamination. An unusual offset-compression mode was observed for compressive bearing-bypass loading in which the specimen failed across its width along a line offset from the hole. The computed lamina strains in the fiber direction were used in a combined analytical and experimental approach to predict bearing-bypass diagrams for damage onset from a few simple tests.

Naik, R. A.↗

A Finite-Element Approach for the Partitioning of Carbon in Q&P Steel

This paper reports a Galerkin finite-element analysis of carbon partitioning from martensite into austenite during the quenching and partitioning (Q&P) processes in steels. In contrast to classical or sophisticated diffusion field models, an alternative nonlinear governing equation based on chemical potential and composition is considered. The model is applied to simulate the carbon partitioning of modified 22MnB5 alloys assuming an immobile austenite–martensite phase boundary and, in turn, is compared with experimental measurements of the volume fraction and carbon content of retained austenite. The simulations show outstanding results on the influence of Si and C content on the partitioning parameters.

36 MATERIALS SCIENCE↗

STAGS Example Problems Manual

This document summarizes the STructural Analysis of General Shells (STAGS) development effort, STAGS performance for selected demonstration problems, and STAGS application problems illustrating selected advanced features available in the STAGS Version 5.0. Each problem is discussed including selected background information and reference solutions when available. The modeling and solution approach for each problem is described and illustrated. Numerical results are presented and compared with reference solutions, test data, and/or results obtained from mesh refinement studies. These solutions provide an indication of the overall capabilities of the STAGS nonlinear finite element analysis tool and provide users with representative cases, including input files, to explore these capabilities that may then be tailored to other applications.

Knight, Norman F., Jr.↗

TURBOMAT-FR: Turbomachinery Aeroelastic Forced Response Analysis Automation Using MATLAB®: PART 1

The primary aim of this effort is to develop a software tool named “Turbomachinery Aeroelastic Analysis Tool for Forced Response (TURBOMAT-FR)” using MATLAB® (The MathWorks, Inc.) scripts. The tool will aid in performing routine forced response analysis of turbomachinery fan blades with the aid of the modal summation method (MSUM). The MSUM approach requires a modal solution consisting of modal displacements, modal frequencies, and modal stresses. The MATLAB® scripts facilitate easy extraction of the required quantities from the computational fluid dynamics (CFD) and MSC Nastran (Hexagon AB) solution files. These quantities are subsequently utilized by the MSUM approach to perform a complete forced response analysis.The MATLAB® scripts in TURBOMAT-FR are utilized in postprocessing of the MSC Nastran finite element analysis outputs in three types of solutions or steps, namely (1) stresses and displacements from static and steady response solution, (2) unsteady stresses and displacements from direct forced response solution, and (3) modal solution containing modal displacements and modal stresses. In step (4), separate MATLAB® scripts are also developed to read the processed outputs in step (3) and perform forced response analysis using MSUM. The TURBOMAT-FR MATLAB® scripts mentioned previously are presented in two reports designated “Part 1” and “Part 2”. The current report, Part 1, presents the scripts needed to accomplish steps (1) and (2), noted previously. This will be exclusively useful for performing only the static and steady response analysis and the forced response analysis using the direct forced response solution approach. Part 2 contains the TURBOMAT-FR MATLAB® scripts needed to accomplish steps (3) and (4). The MATLAB® scripts given in Part 2 facilitate the calculation of unsteady stresses using MSUM and provide an automated procedure associated with aeroelastic forced response analysis with different pressure files for the same structural model. The unsteady stresses calculated using MSUM in Part 2 can be compared with those presented in Part 1. A cantilevered blade-alone model subjected to a realistic pressure loading to a boundary was used for static and unsteady direct forced response analysis to demonstrate the effectiveness of the TURBOMATFR MATLAB® scripts.

MATLAB-Scripts↗

A Modified Isotropic–Kinematic Hardening Model to Predict the Defects in Tube Hydroforming Process

Numerical simulations of tube hydroforming process of hollow crankshafts were conducted by using finite element analysis method. Moreover, the modified model involving the integration of isotropic–kinematic hardening model with ductile criteria model was used to more accurately optimize the process parameters such as internal pressure, feed distance and friction coefficient. Subsequently, hydroforming experiments were performed based on the simulation results. The comparison between experimental and simulation results indicated that the prediction of tube deformation, crack and wrinkle was quite accurate for the tube hydroforming process. Finally, hollow crankshafts with high thickness uniformity were obtained and the thickness distribution between numerical and experimental results was well consistent.

36 MATERIALS SCIENCE↗

Thermal Analysis of a 50 kW Three-Phase Wireless Charging System

In this paper, the thermal analysis of a 50 kW three-phase wireless charging system (WCS) is presented. Addressing the thermal challenge is essential for designing a compact charging pad for 50 kW and higher-power WCS pads. Low thermal conductivity of the Litz wire and ferrite, and uneven distribution of the coil, and core loss cause the high temperature in the charging pads. In this paper, the loss distribution of a 50 kW three-phase WCS is investigated, and the temperature distribution is simulated using finite element analysis (FEA) considering the magnetic and non-magnetic materials of a charging pad. The thermal characteristics of an extremely high-power density 50 kW WCS prototype are tested experimentally for 10 minutes of operation. The simulation and experimental results show that the coil temperature increases to 65°C, the core temperature varies between 50°C to 150°C, and the packaging temperature increases to 65°C after 10 minutes of operation at rated 50 kW output power.

Mohammad, Mostak↗

Three-dimensional analysis of chevron-notched specimens by boundary integral method

The chevron-notched short bar and short rod specimens was analyzed by the boundary integral equations method. This method makes use of boundary surface elements in obtaining the solution. The boundary integral models were composed of linear triangular and rectangular surface segments. Results were obtained for two specimens with width to thickness ratios of 1.45 and 2.00 and for different crack length to width ratios ranging from 0.4 to 0.7. Crack opening displacement and stress intensity factors determined from displacement calculations along the crack front and compliance calculations were compared with experimental values and with finite element analysis.

Mendelson, A.↗