Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
NASA NTRS1947

Theoretical Additional Span Loading Characteristics of Wings with Arbitrary Sweep, Aspect Ratio, and Taper Ratio

The Weissinger method for determining additional span loading has been used to find the lift-curve slope, spanwise center of pressure, aerodynamic center location, and span loading coefficients of untwisted and uncambered wings having a wide range of plan forms characterized by various combinations of sweep, aspect ratio, and taper ratio. The results are presented as variations of the aerodynamic characteristics with sweep angle for various values of aspect ratio and taper ratio. Methods are also included for determining induced drag and the approximate effects of compressibility. Despite the limitations of a lifting line method such as Weissinger's, the good agreement found between experimentally and theoretically determined characteristics warrants confidence in the method. In particular, it is believed that trends observed in results of the Weissinger method should be reliable. One of the most significant results showed that for each angle of sweep there is a taper ratio for which aspect ratio has little effect on the span loading and for which the loading is practically elliptical. This elliptic loading is approached at a taper ratio of 1.39 for 30 degree of sweepforward, 0.45 for zero degree of sweepback. (author)

Deyoung, John↗
NASA NTRSDate not supplied

Wind Tunnel Testing of AFC over a Deflected Aileron on the High-Lift Common Research Model

Active flow control (AFC) using discrete fluidic actuators distributed along the span, just upstream of the deflected aileron of the 10% scale high-lift version of the Common Research Model (CRM-HL), was evaluated during a wind tunnel test in the NASA Langley 14- by 22-Foot Subsonic Tunnel. For this set of experiments, a new outboard section was fabricated incorporating a deflectable aileron. Aileron deflection angles of 0, 7.5, 16, and 25 were investigated. This experimental investigation is in response to a recent study by Boeing potential to use AFC with a drooped aileron during takeoff to improve lift-to-drag ratio (L/D) by as much as 5%, depending on AFC mass flow rate. AFC is used at deflection angles above the nominal deflection of 7.5 to control the resulting flow separation that occurs and potentially improve L/D. Improvements in aircraft low-speed L/D can affect vehicle range and/or payload. Tuft flow visualization data, steady and unsteady surface pressure data, and force and moment data are used to compare the flowfields with and without AFC. Parameters varied include actuator momentum coefficient and aileron deflection angle. The surface pressure and tuft flow visualization results indicate that without AFC, the flow over a majority of the aileron upper surface is separated for aileron deflection angles larger than 7.5. When AFC is applied, the flow is reattached to the aileron. Force and moment results show that a local increase in lift leads to an increase in L/D of at least 3.5% using mass flow rates thought to be available from air sources onboard a commercial transport.

AFC↗
DOE OSTI2023

Aerodynamic Rotor Design for a 25 MW Offshore Downwind Turbine

Continuously increasing offshore wind turbine scales require rotor designs that maximize power and performance. Downwind rotors offer advantages in lower mass due to reduced potential for tower strike, and is especially true at large scales, e.g., for a 25 MW turbine. In this study, three 25 MW downwind rotors, each with different prescribed lift coefficient distributions were designed (chord, geometry, and twist) and compared to maximize power production at unprecedented scales and Reynolds numbers, including a new approach to optimize rotor tilt and coning based on aeroelastic effects. To achieve this objective the design process was focused on achieving high power coefficients, while maximizing swept area and minimizing blade mass. Maximizing swept area was achieved by prescribing pre-cone and shaft tilt angles to ensure the aeroelastic orientation when the blades point upwards was nearly vertical at nearly rated conditions. Maximizing the power coefficient was achieved by prescribing axial induction factor and lift coefficient distributions which were then used as inputs for an inverse rotor design tool. The resulting rotors were then simulated to compare performance and subsequently optimized for minimum rotor mass. To achieve these goals, a high Reynolds number design space was developed using computational predictions as well as new empirical correlations for flatback airfoil drag and maximum lift. Within this design space, three rotors of small, medium and large chords were considered for clean airfoil conditions (effects of premature transition were also considered but did not significantly modify the design space). The results indicated that the medium chord design provided the best performance, producing the highest power in Region 2 from simulations while resulting in the lowest rotor mass, both of which support minimum LCOE. The methodology developed herein can be used for the design of other extreme-scale (upwind and downwind) turbines.

downwind rotors↗
NASA NTRS1984

Applications of CONMIN to wing design optimization with vortex flow effect

Slender wings on supersonic cruise configurations are expected to be thin and highly swept. As a result, edge-separated vortex flow is inevitable and must be accounted for in aerodynamic analysis and design. The present method is based on the method of suction analogy to calculate the total aerodynamic characteristics. The method requires the solution of the attached flow problem, the latter being solved by a low-order panel method in subsonic and supersonic flow. In essence, the lifting pressure is calculated by using a pressure-doublet distribution satisfying the Prandtl-Glauert equation. From the pressure distribution, the leading-edge suction is calculated. The latter is assumed to be the vortex lift through the method of suction analogy. For a cambered wing, the location of vortex-lift action point is important in predicting the aerodynamic characteristics. It is also seen that the effect of camber shape appears nonlinearly in all aerodynamic expressions. To design the camber shape, the camber slope is represented by a cosine Fourier series at each of several spanwise stations. The Fourier coefficients are the design variables. To design a leading-edge flap in the vortex flow (i.e., a vortex flap), the coordinates of corner points and the deflection angle are the design variables. The process of wing design is to determine the camber shape and twist distribution such that an objective function, typically the drag, is minimized, subject to various constraints.

Lan, C. E.↗
NASA NTRS1921

The effect of staggering a biplane

This investigation was carried out by request of the United States Air Service at the Massachusetts Institute of Technology wind tunnel in 1918. As the data collected may be of general interest, they are published here by the National Advisory Committee for Aeronautics. The lift, drag, and center of pressure travel are determined for a biplane with a stagger varying from +100% to -100%. It is found that the efficiency and the maximum lift increase with positive stagger. With large positive staggers the center of pressure is far forward and has a very slight travel with changes in lift coefficient.

Norton, F H↗
NASA NTRS1931

The Effect of Slots and Flaps on the Lift and Drag of the Mcdonnell Airplanes Determined in Flight

This note contains the results of flight test conducted by the National Advisory Committee for Aeronautics on a low-wing monoplane equipped with leading-edge slots extending over the entire wing and flaps extending only to the ailerons, to find their effect on the lift and drag characteristics of the airplane. Curves are given showing the lift and drag characteristics of the airplane for the following conditions of the slots and flaps neutral; slots closed and flaps down; and slots open and flaps down. In addition, the high and low speed in level flight and the climbing characteristics are given. The results show that the slots used alone increase the maximum lift coefficient 54 per cent; the flaps alone increase it 38 per cent; and the slots and flaps in combination decrease the landing speed from 60 to 43 m.p.h.; increase the speed range of the airplane 40 per cent; and increase the glide angle at landing speed 4.2 degrees.

Soule, Hartley A↗
NASA NTRS1947

High-Speed Aerodynamic Characteristics of a 1/7-Scale Model of the Northrop YB-49 Airplane

Tests were conducted to find the effects of compressibility on the longitudinal stability and control of a 1/7-scale semispan model of the Northrop YB-49 airplane. Lift, drag, pitching moment, and elevon hinge moments were measured and are presented in graphical form. The results show that, due to a loss of lift on the outboard portion of the wing, the longitudinal static stability decreased rapidly as the Mach numbers increased above 0.735 the model experienced a climbing moment at positive lift coefficients. Also, a longitudinal-control effectiveness began to decrease at a Mach number of about 0.725

Robinson, Robert C.↗
NASA NTRS1921

Ground influence on airfoils

The question of ground influence on airplanes has recently attracted some attention in view of the claims made by certain designers that the landing speed of their airplanes is much decreased by an increase in lift coefficient due to the proximity of the ground in landing. The results of wind tunnel tests indicate that ground effect is not entirely beneficial. It decreases the landing speed and cushions the landing shock somewhat. However, it does so at the expense of an increased length of preliminary skimming over the ground. By decreasing the drag and increasing the lift, it lengthens the distance necessary for the airplane to travel before losing enough speed to land. On the other hand, its influence is helpful in taking off, especially in the case of flying boats with their low-lying wings. In the conventional tractor airplane, the height of the wings above the ground is determined largely by propeller clearance. However, a small low-speed airplane like the Pischoff and large low-speed commercial aircraft with engines between wings can utilize ground influence to good advantage.

Raymond, Arthur E↗
NASA NTRS1983

Aerocapture and aeroassisted orbital transfer - A high performance leverage space technology

Single pass aerocapture and aeroassisted orbital transfer designs are discussed for modifying spacecraft orbits using planetary atmospheres. Aerodynamic drag can be used to shift a hyperbolic flyby trajectory to a planetary orbit by having the spacecraft altering its in-plane L/D ratio to maintain constant drag until the desired velocity is attained. The spacecraft would then move out of the atmosphere, sometimes with a small propulsive assist. Sample missions to Uranus, Jupiter, and Titan are mentioned, with mission scenarios commencing with a Shuttle launch. Biconic-shaped spacecraft are cited as having the best L/D for insertion accuracy, a low hypersonic ballistic coefficient, and volumeric efficiency. Aeroassisted orbital transfer involves atmospheric braking in order to shed velocity on a return trip from higher orbits. No decision has yet been made as to the spacecraft shape, but calculations indicate that aeroassist braking before return to LEO for rendezvous with the Shuttle has the potential for the lowest cost/mass to GEO of any delivery system currently under consideration.

Cruz, M. I.↗
NASA NTRS1996

Analysis of Flowfields over Four-Engine DC-X Rockets

The objective of this study is to validate a computational methodology for the aerodynamic performance of an advanced conical launch vehicle configuration. The computational methodology is based on a three-dimensional, viscous flow, pressure-based computational fluid dynamics formulation. Both wind-tunnel and ascent flight-test data are used for validation. Emphasis is placed on multiple-engine power-on effects. Computational characterization of the base drag in the critical subsonic regime is the focus of the validation effort; until recently, almost no multiple-engine data existed for a conical launch vehicle configuration. Parametric studies using high-order difference schemes are performed for the cold-flow tests, whereas grid studies are conducted for the flight tests. The computed vehicle axial force coefficients, forebody, aftbody, and base surface pressures compare favorably with those of tests. The results demonstrate that with adequate grid density and proper distribution, a high-order difference scheme, finite rate afterburning kinetics to model the plume chemistry, and a suitable turbulence model to describe separated flows, plume/air mixing, and boundary layers, computational fluid dynamics is a tool that can be used to predict the low-speed aerodynamic performance for rocket design and operations.

Wang, Ten-See↗
NASA NTRS1996

Effect of Full-Chord Porosity on Aerodynamic Characteristics of the NACA 0012 Airfoil

A test was conducted on a model of the NACA 0012 airfoil section with a solid upper surface or a porous upper surface with a cavity beneath for passive venting. The purposes of the test were to investigate the aerodynamic characteristics of an airfoil with full-chord porosity and to assess the ability of porosity to provide a multipoint or self-adaptive design. The tests were conducted in the Langley 8-Foot Transonic Pressure Tunnel over a Mach number range from 0.50 to 0.82 at chord Reynolds numbers of 2 x 10(exp 6), 4 x 10(exp 6), and 6 x 10(exp 6). The angle of attack was varied from -1 deg to 6 deg. At the lower Mach numbers, porosity leads to a dependence of the drag on the normal force. At subcritical conditions, porosity tends to flatten the pressure distribution, which reduces the suction peak near the leading edge and increases the suction over the middle of the chord. At supercritical conditions, the compression region on the porous upper surface is spread over a longer portion of the chord. In all cases, the pressure coefficient in the cavity beneath the porous surface is fairly constant with a very small increase over the rear portion. For the porous upper surface, the trailing edge pressure coefficients exhibit a creep at the lower section normal force coefficients, which suggests that the boundary layer on the rear portion of the airfoil is significantly thickening with increasing normal force coefficient.

Mineck, Raymond E.↗
NASA NTRS2012

Inviscid Analysis of Extended Formation Flight

Flying airplanes in extended formations, with separation distances of tens of wingspans, significantly improves safety while maintaining most of the fuel savings achieved in close formations. The present study investigates the impact of roll trim and compressibility at fixed lift coefficient on the benefits of extended formation flight. An Euler solver with adjoint-based mesh refinement combined with a wake propagation model is used to analyze a two-body echelon formation at a separation distance of 30 spans. Two geometries are examined: a simple wing and a wing-body geometry. Energy savings, quantified by both formation drag fraction and span efficiency factor, are investigated at subsonic and transonic speeds for a matrix of vortex locations. The results show that at fixed lift and trimmed for roll, the optimal location of vortex impingement is about 10% inboard of the trailing airplane s wing-tip. Interestingly, early results show the variation in drag fraction reduction is small in the neighborhood of the optimal position. Over 90% of energy benefits can be obtained with a 5% variation in transverse and 10% variation in crossflow directions. Early results suggest control surface deflections required to achieve trim reduce the benefits of formation flight by 3-5% at subsonic speeds. The final paper will include transonic effects and trim on extended formation flight drag benefits.

Kless, James↗
NASA NTRS2008

Spectral Attenuation of Sound in Dilute Suspensions with Nonlinear Particle Relaxation

Previous studies on the sound attenuation in particle-laden flows under Stokesian drag and conduction-controlled heat transfer have been extended to accommodate the nonlinear drag and heat transfer. It has been shown that for large particle-to-fluid density ratio, the particle Reynolds number bears a cubic relationship with (omega(tau))(sub d) (where omega is the circular frequency and (tau)(sub d) the Stokesian particle relaxation time). This dependence leads to the existence of a peak value in the linear absorption coefficient occurring at a finite value of(omega(tau))(sub d). Comparison of the predictions with the test data for the spectral attenuation of sound with water injection in a perfectly expanded supersonic air jet shows a satisfactory trend of the theory accounting for nonlinear particle relaxation processes.

Kandula, Max↗
NASA NTRS2008

Spectral Attenuation of Sound in Dilute Suspensions with Nonlinear Particle Relaxation

Theoretical studies on the dissipation and dispersion of sound in two-phase suspensions have been briefly reviewed. Previous studies on the sound attenuation in particle-laden flows under Stokesian drag and conduction-controlled heat transfer have been extended to accommodate the nonlinear drag and heat transfer. It has been shown that for large particle-to-fluid density ratio, the particle Reynolds number bears a cubic relationship with Omega Tau(sub d) (where Omega is the circular frequency and Tau(sub d) the Stokesian particle relaxation time). This dependence leads to the existence of a peak value in the linear absorption coefficient occurring at a finite value Omega Tau (sub d). Comparison of the predictions with the test data for the spectral attenuation of sound with water injection in a perfectly expanded supersonic air jet shows a satisfactory trend of the theory accounting for nonlinear particle relaxation processes.

Kandula, M.↗
NASA NTRS1981

Full-scale aerodynamic characteristics of a propellar installed on a small twin-engine aircraft wing panel

Full-scale measurements of shaft thrust and torque were made. Wind-tunnel speeds and blade angles were set for full-scale flight conditions. Excellent quality measurements were obtained of the thrust coefficient, the power coefficient, and the propeller efficiency for various values of the advance ratio and the blade incidence angle at 3/4-blade radius. A conventional propeller theory found in the literature was applied to the present results. Although thrust, power, and efficiency were somewhat overpredicted, the advance ratio for maximum efficiency was predicted quite accurately. It was found that, for some conditions, spinner drag could be significant. A simple correction that was based on the spinner base pressure substantially accounted for the changes in efficiency that resulted from this cause.

Barlow, P. R.↗
NASA NTRS1998

Continued Development and Application of Circulation Control Pneumatic Technology to Advanced Transport Aircraft

Personnel of the Georgia Tech Research Institute (GTRI) Aerospace and Transportation Lab have completed a four-year grant program to develop and evaluate the pneumatic aerodynamic technology known as Circulation Control (CC) or Circulation Control Wing (CCW) for advanced transport aircraft. This pneumatic technology, which employs low-level blowing from tangential slots over round or near-round trailing edges of airfoils, greatly augments the circulation around a lifting or control surface and thus enhances the aerodynamic forces and moments generated by that surface. Two-dimensional force augmentations as high as 80 times the input blowing momentum coefficient have been recorded experimentally for these blown devices, thus providing returns of 8000% on the jet momentum expended. A further benefit is the absence of moving parts such as mechanical flaps, slats, spoilers, ailerons, elevators and rudders from these pneumatic surfaces, or the use of only very small, simple, blown aerodynamic surfaces on synergistic designs which integrate the lift, drag and control surfaces. The application of these devices to advanced aircraft can offer significant benefits in their performance, efficiency, simplicity, reliability, economic cost of operation, noise reduction, and safety of flight. To further develop and evaluate this potential, this research effort was conducted by GTRI under grant for the NASA Langley Research Center, Applied Aerodynamics Division, Subsonic Aerodynamics Branch, between June 14, 1993 and May 31, 1997.

Englar, Robert J.↗
NASA NTRS2002

Thermal Analysis and Correlation of the Mars Odyssey Spacecraft's Solar Array During Aerobraking Operations

The Mars Odyssey spacecraft made use of multipass aerobraking to gradually reduce its orbit period from a highly elliptical insertion orbit to its final science orbit. Aerobraking operations provided an opportunity to apply advanced thermal analysis techniques to predict the temperature of the spacecraft's solar array for each drag pass. Odyssey telemetry data was used to correlate the thermal model. The thermal analysis was tightly coupled to the flight mechanics, aerodynamics, and atmospheric modeling efforts being performed during operations. Specifically, the thermal analysis predictions required a calculation of the spacecraft's velocity relative to the atmosphere, a prediction of the atmospheric density, and a prediction of the heat transfer coefficients due to aerodynamic heating. Temperature correlations were performed by comparing predicted temperatures of the thermocouples to the actual thermocouple readings from the spacecraft. Time histories of the spacecraft relative velocity, atmospheric density, and heat transfer coefficients, calculated using flight accelerometer and quaternion data, were used to calculate the aerodynamic heating. During aerobraking operations, the correlations were used to continually update the thermal model, thus increasing confidence in the predictions. This paper describes the thermal analysis that was performed and presents the correlations to the flight data.

Dec, John A.↗