Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DRAG”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Drag Tests of 4/9-Scale Model Engine Nacelles with Various Cowlings

Results are given of drag tests of 4/9-scale model radial air-cooled engine nacelles made as a part of a general investigation of wing-nacelle-propeller interference. A small nacelle of the type commonly used with exposed engine cylinders was tested with various forms of cowling over the cylinders. The effects of cowling-ring position and of angle of ring chord to the thrust line were investigated. An N.A.C.A. cowled nacelle and a smooth body were also tested. The results are given at 50, 75, and 100 miles per hour for -5 degrees, 0 degrees, 5 degrees, 10 degrees, 15 degrees angle of pitch.

Windler, Ray↗

The Aerodynamic Drag of Flying-boat Hull Model as Measured in the NACA 20-foot Wind Tunnel I.

Measurements of aerodynamic drag were made in the 20-foot wind tunnel on a representative group of 11 flying-boat hull models. Four of the models were modified to investigate the effect of variations in over-all height, contours of deck, depth of step, angle of afterbody keel, and the addition of spray strips and windshields. The results of these tests, which cover a pitch-angle range from -5 to 10 degrees, are presented in a form suitable for use in performance calculations and for design purposes.

Hartman, Edwin P↗

The drag of inflatable rubber de-icers

Force tests on rubber de-icer models of several different profiles, at approximately one-third full scale, been carried out in the NACA 8-foot high speed wind tunnel. The conventional de-icer installation, deflated, added about 15 percent to the smooth-wing drag and, inflated, added about 100 percent. An improved installation with flash attaching strips added about 10 percent, deflated. The bulging, or ballooning, of de-icers from the wing surface is described and some remedies are discussed.

Robinson, Russell G↗

Theoretical supersonic lift and drag characteristics of symmetrical wedge-shape-airfoil sections as affected by sweepback outside the Mach cone

The theoretical supersonic section lift and drag characteristics of thin wedge-shape, untapered airfoils with sweepback are presented. The results apply to those parts of the wing in two dimensional flow and are not applicable to wings swept back within the Mach cone of the center section. The results may also be applied to swept-forward wings if the angle of sweep is not enough to put the wing within the Mach cone from the tips.

Ivey, H Reese↗

The zero-lift drag of a slender body of revolution (NACA RM-10 research model) as determined from tests in several wind tunnels and in flight at supersonic speeds

Presents zero-lift drag data of an NACA RM-10 slender body of revolution with and without stabilizing fins attached. The results from several wind tunnels and in flight are compared. The results cover a Reynolds number range from about 1 time 10 to the 6th power to 40 times 10 to the 6th power for the flight models. The Mach numbers covered include 1.5 to 2.4 in the wind tunnels and 0.85 to 2.5 in flight.

FLOW, SUPERSONIC↗

Lift, Drag, and Pitching Moment of Low-aspect-ratio Wings at Subsonic and Supersonic Speeds : Twisted and Cambered Triangular Wing of Aspect Ratio 2 with NACA 0003-63 Thickness Distribution

This report presents the results of an investigation to ascertain the lift, drag, and pitching moment of a wing-body combination having a triangular wing of aspect ratio 2 with NACA 0003-63 thickness distribution in streamwise planes and twisted and cambered for a nearly elliptical span load distribution. Results are shown for Mach numbers from 0.60 to 0.90 and from 1.30 to 1.70 at Reynolds numbers of 3.0 million and 7.5 million.

WINGS, COMPLETE - DESIGN VARIABLES↗

Pressure Recovery, Drag, and Subcritical Stability Characteristics of Three Conical Supersonic Diffusers at Stream Mach Numbers from 1.7 to 2.0

A study of a 20 degree and a 25 degree half-angle high mass-flow ratio conical supersonic inlet was made on a 16-inch ram jet in the 8- by 6-foot supersonic tunnel. A greater range of stable subcritical operation was obtained with the low mass-flow ratio inlets; a greater range was obtained with the 25 degree than with the 20 degree half-angle low mass-flow ratio inlet. The high mass-flow ratio inlet had the least drag.

DIFFUSERS, SUPERSONIC↗

A note on the drag due to lift of delta wings at Mach numbers up to 2.0

In order to indicate the effects of Reynolds number and other variables on the drag due to lift of delta wings for Mach numbers up to 2.0, the results of several investigations of wing-body combinations employing delta wings with aspect ratios from 2 to 4 have been assembled for comparison. Effects of Reynolds number, leading-edge radius, and thickness ratio could be correlated with Reynolds number based on the leading-edge radius as a parameter. The results indicated that leading-edge Reynolds number effects were large at low speeds, but decreased with increases in Mach number. The effects of aspect ratio, wing modifications, and trim requirements are discussed.

MACH NUMBER EFFECTS - COMPLETE WINGS↗

Preliminary Drag and Heat-transfer Data Obtained from Air-launched Cone-cylinder Test Vehicle over Mach Number Range from 1.5 to 5.18

An air-launched cone-cylinder test vehicle designed to obtain data at Mach numbers above 4.0 was rocket boosted from a release Mach number of 5.18. The vehicle was launched at an altitude of 35,000 feet and reached peak velocity of 5150 feet per second at 28,500 feet. The total-drag coefficient (based on maximum cross-sectional area) decreased gradually from 0.31 at a Mach number of 1.75 to 0.145 at a Mach number of 5.18, while the Reynold's number (based on body length) increased from 31 x 10 to the 6th power to 107 x 10 to the 6th power. The skin friction coefficients, in general, were slightly lower than Van Driest's theoretical values for similar wall-temperature conditions. Convective heat-transfer coefficients were obtained from a single skin-thermocouple measurement. The maximum wall temperature recorded was 1240 degrees r.

Messing, Wesley E↗

Investigation of Thrust and Drag Characteristics of a Plug-type Exhaust Nozzle

An investigation was conducted in the 8- by 6-foot supersonic wind tunnel on the external and internal characteristics of a plug-type exhaust nozzle. Two positions of the center plug, one simulating a convergent nozzle and the other a convergent-divergent nozzle, were investigated. Data were obtained at free-stream Mach numbers of 0.1, 0.6, 1.6, and 2.0 over a pressure-ratio range of 1 to 20 and angles of attack of zero and 8 degrees. Results of this investigation indicated that the plug nozzle had thrust-minus-drag performance over the entire pressure-ratio range comparable with equivalent conventional nozzles. The effect of the exhaust jet on the external aerodynamics was similar to results observed for conventional nozzles. In addition, the thrust characteristics were generally insensitive to external flow and good agreement was noted with data obtained on comparable plug nozzles in quiescent air.

Hearth, Donald P↗

Preliminary Results of an Investigation at Transonic Speeds to Determine the Effects of a Heated Propulsive Jet on the Drag Characteristics of a Related Series of Afterbodies

Preliminary results are presented from an investigation to determine the influence of afterbody geometry on the effects of a sonic propulsive jet at transonic speeds. The results presented are base pressure coefficient and afterbody pressure-drag coefficient as a function of jet pressure ratio for different values of Mach number and jet temperature. Geometric parameters investigated include boattail angle, jet-to-model diameter ratio, and jet-to-base diameter ratio.

Henry, Beverly Z , Jr↗

Investigation of Local Heat-transfer and Pressure Drag Characteristics of a Yawed Circular Cylinder at Supersonic Speeds

Local heat-transfer coefficients, temperature recovery factors, and pressure distributions were measured on the front side of a circular cylinder at a nominal Mach number of 3.9 over a range of free-stream Reynolds numbers from 2.1 x 10 to the 3rd power to 6.7 x 10 to the 3rd power and yaw angles from zero degrees to 44 degrees. Yawing the cylinder reduced the heat-transfer coefficients and the pressure drag coefficients. The amount of reduction may be predicted by a theory presented herein.

Goodwin, Glen↗

A method for the direct determination of wing-section drag

In order that the method may be more easily understood, we will first consider the simpler case when there is no lift, but only drag, and when the streamlines at the measuring point behind the obstacle are nearly parallel. Moreover, the flow is assumed not to deviate much from the two-dimensional flow.

Betz, A↗

The variation of aerofoil lift and drag coefficients with changes in size and speed

This report contains the results of an investigation into the effect of changes in size and speed upon aerofoil lift and drag coefficients. Certain empirical limitations to the interchangeability of v and l in the general equation of fluid resistance are pointed out and the existing methods of correcting for scale are criticized. New methods of correcting for scale by means of simple formulae are derived and checked by comparison with test results.

Diehl, Walter S↗

The drag of Zeppelin airships

This report is a discussion of the results of tests with Zeppelin airships, in which the propellers were stopped as quickly as possible while the airship was in full flight. In this paper the author refers to the theory involved in these tests and calls attention to one scientifically interesting fact which can be derived from the tests and which has not yet been noted. The most important question concerning the tests is, of course: does the negative acceleration of an airship with stopped propellers supply proper data for determining the drag of the airship when in uniform flight? This can not be absolutely answered, however, except that in this particular case the agreement is sufficient and that the data obtained from the test are the true quantities, or, at least, the approximate quantities wanted.

Munk, Max M↗

The Drag of C Class Airship Hull with Varying Length of Cylindric Midships

A model of the C class airship hull, when severed at its major section and provided with a cylindric mid-body of variable length, had its air resistance increased about in proportion to the length of the mid-body up to 3 diameters, and in about the manner to be expected from the increase of skin friction on this variable length. For greater length the drag increased less and less rapidly.

Zahm, A F↗

Lift, Drag, and Elevator Hinge Moments of Handley Page Control Surfaces

This report combines the wind tunnel results of tests on four control surface models made in the two wind tunnels of the Navy Aerodynamic Laboratory, Washington Navy Yard, during the years of 1922 and 1924, and submitted for publication to the National Advisory Committee for Aeronautics May 7, 1927. The purpose of the tests was to compare, first, the lifts and the aerodynamic efficiencies of the control surfaces from which their relative effectiveness as tail planes could be determined; then the elevator hinge moments upon which their relative ease of operation depended. The lift and drag forces on the control surface models were obtained for various stabilizer angles and elevator settings in the 8 by 8 foot tunnel by the writer in 1922; the corresponding hinge moments were found in the 4 by 4 foot tunnel by Mr. R. M. Bear in 1924. (author)

Smith, R H↗

A proof of the theorem regarding the distribution of lift over the span for minimum induced drag

The proof of the theorem that the elliptical distribution of lift over the span is that which will give rise to the minimum induced drag has been given in a variety of ways, generally speaking too difficult to be readily followed by the graduate of the average good technical school of the present day. In the form of proof this report makes an effort to bring the matter more readily within the grasp of this class of readers.

Durand, W F↗