Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Compressibility effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

High Angle of Incidence Implications upon Air Intake Design and Location for Supersonic Cruise Aircraft and Highly Maneuverable Transonic Aircraft

Computational results which show the effects of angle of attack on supersonic mixed compression inlet performance at four different locations about a hypothetical forebody were obtained. These results demonstrate the power of the computational method to predict optimum inlet location, orientation, and centerbody control schedule for design and off design performance. The effects of inlet location and a forward canard on the angle-of-attack performance of a normal shock inlet at transonic speeds were studied. The data show that proper integration of inlet location and a forward canard can enhance the angle-of-attack performance of a normal shock inlet. Two lower lip treatments for improving the angle-of-attack performance of rectangular inlets at transonic speeds are discussed.

Presley, L. S.↗
NASA NTRS1998

Characterization of Asymptotic Entrainment Rate for Compressible Jets

Experimental results for the spreading and centerline velocity decay rates are presented for round, compressible, submerged jets, with total temperature same as ambient temperature, covering a 'jet Mach number' (M(sub J)) range of 0.3 - 2.0. Data from a convergent and a convergent-divergent nozzle are considered. The spreading rate is determined from the total longitudinal mass fluxes measured by Pilot probe survey. Results for the far asymptotic regions show that both spreading and centerline velocity decay rates, when normalized by conditions at the nozzle exit, decrease with increasing M(sub J). Dimensional analysis and isentropic calculations predict this Mach number dependence well. The analysis also demonstrates that an increase in the 'potential core length' of the jet occurring with increasing M(sub J), a commonly observed trend, is largely accounted for simply by the variations in the density and static pressure at the nozzle exit. The effect of decreasing mixing efficiency with increasing compressibility is inferred to contribute only partially to the latter trend.

Zaman, K. B. M. Q.↗
DOE OSTI2026

Cosmological constraints from a joint DESI DR1 Full-Shape and DR2 BAO

We present a cosmological analysis combining full-shape (FS) clustering measurements from the Dark Energy Spectroscopic Instrument (DESI) DR1 with baryon acoustic oscillation (BAO) measurements from DESI DR2. To achieve a robust combination that accounts for the correlation between the two data releases, we employ the ShapeFit compression method and estimate the joint covariance using EZmocks. This compressed approach inherently mitigates the prior volume effects that have previously dominated Bayesian constraints from DESI data with minimal external priors. Consequently, we obtain — for the first time within a Bayesian framework — reliable DESI-only constraints on extensions to ΛCDM using only a Big Bang Nucleosynthesis prior on the baryon density and a wide prior on the spectral index. In flat ΛCDM, we find Ω m = 0.3035 ± 0.0085, h = 0.6876 ± 0.0059, and σ 8 = 0.822 ± 0.034. For the w 0 w a CDM dynamical dark energy model, we measure w 0 = -0.49 ± 0.25 and w a = -1.52 ± 0.77, improving constraints by ∼ 30% relative to the analogous DR1 measurement and reducing the discrepancy with ΛCDM to 1.4σ when compared to BAO only analyses. We also report competitive limits on the sum of neutrino masses and spatial curvature. This work demonstrates that the ShapeFit compression provides a prior-robust and computationally efficient pathway to constrain beyond-ΛCDM physics with large-scale structure.

baryon acoustic oscillations↗
NASA NTRSDate not supplied

3D Printed Ceramic Reinforced Polymer Composites Microstructure and Mechanical Properties

In Fused Filament Fabrication (FFF) 3D printing a part is made by extruding material layer by layer. Benefits of FFF are the ability to print complex shapes quickly and at a lower cost compared to other manufacturing methods. In this work, filaments composed of either silicon carbide (SiC) or zirconium silicate ceramic particulates in a polylactic-acid (PLA) matrix were used to print specimens for microstructural analysis and mechanical testing. Pure PLA samples were also printed and tested as a baseline for comparison. A Design of Experiments approach was used to test the interactions between three different parameters and their effect on ultimate strength, Young’s modulus, and yield strength. For compression test specimens, these parameters were infill percentage, number of shells, and print orientation angle. For tensile test specimens, the parameters were layer height, number of shells, and infill orientation angle. Pre- and post-compression test samples were evaluated by scanning electron microscopy for microstructural analysis. Infill percentage had the greatest effect on mechanical properties while number of shells and print orientation angle had minor effects. When changing the layer lines from perpendicular to parallel, relative to the loading direction, SiC-PLA had higher mechanical properties while pure PLA properties had decreased, and zirconium silicate-PLA had mix results.

Fused filament fabrication↗
NASA NTRS1993

Computational parametric study of sidewall-compression scramjet inlet performance at Mach 10

A computational parametric study of three-dimensional, sidewall-compression scramjet inlets was performed to identify the effects of geometric parameters on inlet performance. The parameters were the leading-edge sweep angle, varied between 30 and 60 deg, and the leading-edge position of the cowl, located at the throat and at two forward positions. A laminar boundary layer with cold-wall (T(sub wall) = 300 K (540 R)) boundary conditions was imposed. The parametric study was performed for a Mach number of 10 and a unit free-stream Reynolds number of 7.06 x 10(exp 6) per meter (2.15 x 10(exp 6) per foot) at a geometric contraction ratio of 5. The performance of each configuration was evaluated in terms of the mass capture, throat Mach number, total pressure recovery, kinetic energy efficiency, and internal compression. One computation of an unswept configuration was included as a baseline to determine the effects of introducing leading-edge sweep on the flow-field parameters. The purpose of the computational parametric study was to perform a trade-off of the effects of various parameters on the global performance of the inlet. Although no single optimal configuration emerged, trade-offs among the stated performance parameters identified a leading-edge sweep angle of 45 deg as possessing the most attractive performance characteristics.

Holland, Scott D.↗
NASA NTRS1991

Data volume reduction for single-look polarimetric imaging radar data

An 8-b quantization scheme to reduce the data volume for single-look complex scattering matrix data measured by polarimetric imaging radar systems is described. The scattering matrices are not symmetrized before compression, thereby retaining information about background noise and system effects. The data volume is reduced by a factor of 3.2. It is shown, with measured data, that the signal to quantization noise ratio for the compression scheme is more than 35 dB for the cross-polarized channels, and more than 45 dB for the copolarized channels.

Van Zyl, Jakob J.↗
DOE OSTI2023

MHD simulation on magnetic compression of field reversed configurations with NIMROD

Abstract Magnetic compression has long been proposed a promising method for plasma heating in a field reversed configuration (FRC). However, it remains a challenge to fully understand the physical mechanisms underlying the compression process, due to its highly dynamic nature beyond the one-dimensional (1D) adiabatic theory model (Spencer et al 1983 Phys. Fluids 26 1564). In this work, magnetohydrodynamics simulations on the magnetic compression of FRCs using the NIMROD code (Sovinec et al 2004 J. Comput. Phys. 195 355) and their comparisons with the 1D theory have been performed. The effects of the assumptions of the theory on the compression process have been explored, and the detailed profiles of the FRC during compression have been investigated. The pressure evolution agrees with the theoretical prediction under various initial conditions. The axial contraction of the FRC can be affected by the initial density profile and the ramping rate of the compression magnetic field, but the theoretical predictions on the FRC’s length in general and the relation r s = 2 r o in particular hold approximately well during the whole compression process, where r s is the major radius of FRC separatrix and r o is that of the magnetic axis. The evolutions of the density and temperature can be affected significantly by the initial equilibrium profile and the ramping rate of the compression magnetic field. During the compression, the major radius of the FRC is another parameter that is susceptible to the ramping rate of the compression field. Basically, for the same magnetic compression ratio, the peak density is higher and the FRC’s radius r s is smaller than the theoretical predictions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Chemical kinetic interactions and sensitivity analyses for 2-ethylhexyl nitrate-doped PRF91 using a reduced mechanism

A numerical and experimental investigation about the chemical kinetic interactions between 2-ethylhexylnitrate (EHN) and PRF91 was performed in this study. Rapid compression machine experiments were conducted to investigate the effect of EHN on the autoignition reactivity of the fuel, and a reduced chemical kinetic mechanism was developed including an EHN sub-model. Experiments showed that the ignition delay decreases as the fuel is doped with EHN, but the effect of the doping level of EHN on the ignition is highly non-linear. Moreover, experiments showed that the EHN effectiveness is lowest during the transition between the low-temperature regime and the negative temperature coefficient (NTC) regime, and it rapidly increases as the temperature increases. Both detailed and (developed) reduced mechanisms were validated against the experimental results, allowing a more in-depth EHN-fuel chemistry study. Additionally, ignition delay sensitivity and EHN effectiveness sensitivity analyses were performed with the reduced mechanism to identify the reactions that control the interaction between EHN and the fuel. As the result, EHN thermal decomposition is only relevant for very low temperatures. The chemistry of EHN-doped fuel is more sensitive to intermediate temperature reactions than that of straight fuel, especially at lower temperatures, due to the effect of EHN on the NTC behavior of the fuel. Finally, the chemistry of EHN-doped fuel is very sensitive to NO 2 -to-NO reactions, especially at high temperatures, because these reactions transform the NO 2 generated by EHN into NO, which is a very effective fuel reactivity enhancer.

2-ethylhexyl nitrate↗
DOE OSTI2020

First-principles study of hydrogen behavior near W/WC interfaces

Hydrogen (H) solution, migration, and binding to vacancies near the tungsten/tungsten carbide (W/WC) interfaces based on hcp WC or bcc W (W/WCb and Wb/WC) have been studied by first-principles simulations to provide insights into the effect of C on H behavior in W exposed to C deposition in fusion reactors. The H behavior near the W/WC interfaces is related to the tensile or compressive strain due to the lattice match and interfacial effects. Near the W/WCb interface, the H solution energy in hcp WC increases approaching the interface, while it decreases from the W side to the interface. The configuration change of the W slab significantly decreases the H solution energy but has only a modest effect on the H migration energy barrier in comparison with the values in bcc W. The interface enhances the H binding to vacancies in WC layers. Both the interface and configuration adjustment of the W slab reduce the H binding to vacancies on the W side of the interface. Near the Wb/WC interface, H solution energies in both WC and W slabs weakly decrease approaching the interface. The configuration change of the WC slab significantly increases the H solution energy and binding energy to vacancies but decreases the H migration energy barrier in comparison with the values in hcp WC. The H energetics near the W/WC interfaces indicate the likelihood of H localization and diffusion in the W side of the interface, rather than diffusing through the interface into WC layers.

Yang, L. (ORCID:0000000322166071)↗
DOE OSTI2024

Effect of Cyclo-Pentane Impurities on the Autoignition Reactivity and Properties of a Gasoline Surrogate Fuel

Surrogate fuels that reproduce the characteristics of full-boiling range fuels are key tools to enable numerical simulations of fuel-related processes and ensure reproducibility of experiments by eliminating batch-to-batch variability. Within the PACE initiative, a surrogate fuel for regular-grade E10 (10%vol ethanol) gasoline representative of a U.S. market gasoline, termed PACE-20, was developed and adopted as baseline fuel for the consortium. Although extensive testing demonstrated that PACE-20 replicates the properties and combustion behavior of the full-boiling range gasoline, several concerns arose regarding the purity level required for the species that compose PACE-20. This is particularly important for cyclo-pentane, since commercial-grade cyclo-pentane typically shows 60%–85% purity. Here, in the present work, the effects of the purity level of cyclo-pentane on the properties and combustion characteristics of PACE-20 were studied. Chemical kinetic simulations were performed to predict the effects of cyclo-pentane impurities on the properties, octane rating, and autoignition reactivity under homogeneous charge compression-ignition conditions of PACE-20. From the numerical results, cyclo-pentane with 85% purity or higher is required to reasonably match both the research octane number and motor octane number of the target gasoline. Finally, homogeneous charge compression-ignition engine simulations show that impurities have only a modest effect on reactivity at naturally aspirated conditions, but cyclo-pentane purity is critical to properly replicate the pressure dependency of the reactivity.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1993

Compression strength failure mechanisms in unidirectional composite laminates containing a hole

Experiments on graphite-epoxy laminated plates containing unloaded small holes show that these laminates are notch insensitive. That is, the uniaxial strength of these laminates with small holes exceeds the strength predicted by a point stress criterion using the stress concentration factor for the in-plane stress field. Laminates containing large holes exhibit notch sensitive behavior and consequently their strength is reasonably well predicted by the stress concentration effect. This hole size effect is manifested both in tension and in compression. Apparently, some mechanism must cause in-plane stress relief for laminates containing small holes. The purpose of this research was to study the influence of geometric nonlinearity on the micromechanical response of a filamentary composite material in the presence of a strain gradient caused by a discontinuity such as a hole. A mathematical model was developed at the micromechanical level to investigate this geometrically nonlinear effect.

Johnson, Eric R.↗
NASA NTRS1985

Stiffener attachment concepts for graphite-epoxy panels designed for postbuckling strength

Stiffener attachment concepts for suppressing or delaying the onset of the skin-stiffener separation failure mode in graphite-epoxy compression panels designed for postbuckling strength were experimentally studied. The effectiveness of these concepts was evaluated using panels with 16-ply skins and a single centrally-located I-shaped stiffener with both static and cyclic compressive loadings. Analytical results suggest that tailoring the relative thicknesses of the panel skin, stiffener attachment flange, and the stiffener web rotational stiffness can minimize the adverse effects of high interface shear and normal stresses. Interface stress levels may be reduced by tapering the thickness of the stiffener attachment flange and properly selecting the stacking sequences of the skin and stiffener attachment flange laminates.

Dickson, John N.↗
NASA NTRS1987

SAR image data compression for an on-line archive system

This paper summarizes the investigation of SAR image data compression for an on-line archive data distribution system. This system is planned for the ground processing system of Alaska SAR Facility (ASF) and Shuttle Imaging Radar (SIR-C). The objective of the SAR image data compression is to enable the data archive system to provide the remote users a large data base with good image quality, short response time, low transfer cost, and minimal decoding complexity. The requirements and limitations of the on-line archive data distribution system are presented. The effects of SAR image data characteristics on data compression are addressed. The users' survey results suggest that compression ratios between 10:1 and 20:1 appear suitable. Based on the algorithm evaluation results, the two-level tree-searched vector quantization technique has been recommended as the SAR image data compression algorithm for the on-line archive data distribution system.

Chang, C. Y.↗